A. N. Shankar
Research Subjects
A. N. Shankar has a total of 40 co-authors. Here are the top co-authors by number of shared publications:
- Guruprasad Balachandran
Department of Mechanical Engineering
2 shared publications - N. Rakesh
Department of Mechanical and Industrial Engineering
2 shared publications - A. Arun Negemiya
Department of Mechanical Engineering , Sri Shakthi Institute of Engineering and Technology , Coimbatore , Tamil Nadu , 641062 , India
1 shared publication - Abdullah Alzlfawi
Department of Civil and Environmental Engineering, College of Engineering, Majmaah University, Al Majmaah, Saudi Arabia
1 shared publication - Alok Kumar
Department of Mechanical Engineering Nalanda College of Engineering Chandi Bihar India
1 shared publication - Areda Batu
Department of Chemical Engineering
1 shared publication
Latest Publications
- 13 June 2025
- Published by World Scientific Pub Co Pte Ltd in International Journal of Structural Stability and Dynamics
- Vol. 27 (06)
Free-Vibration, Damping, and Buckling Performance of Sandwich Beams with Glass Fiber Honeycomb Core and Graphene-Reinforced Composite Face Sheets Based on Higher-Order Theory
The vibration, damping, and buckling behavior of graphene-reinforced sandwich beams are investigated in this work. The honeycomb sandwich beam is composed of graphene-reinforced with glass fiber-reinforced polymer (GFRP) composite skins and a GFRP strip-reinforced honeycomb core. The governing equations are developed by using the finite element formulation along with the higher-order beam theory (HOBT). A significant degree of agreement is found when comparing numerical results to accessible literature. Additionally, this work examines the effects of graphene reinforcement, GFRP honeycomb core thickness, graphene-reinforced GFRP skin layer thickness, and end conditions on the vibration, damping, and buckling behavior of honeycomb sandwich beams. The sandwich beam with graphene-reinforced skins outperforms the neat sandwich beam in terms of natural frequency, damping, and buckling, with improvements of 8.04%, 10.56%, and 18.29%, respectively. The lightweight GFRP honeycomb core, combined with the advanced graphene-reinforced composite face sheets, offers interesting applications and further research.
- 13 June 2025
- Published by World Scientific Pub Co Pte Ltd in International Journal of Structural Stability and Dynamics
- Vol. 27 (06)
Free-Vibration, Damping, and Buckling Performance of Sandwich Beams with Glass Fiber Honeycomb Core and Graphene-Reinforced Composite Face Sheets Based on Higher-Order Theory
The vibration, damping, and buckling behavior of graphene-reinforced sandwich beams are investigated in this work. The honeycomb sandwich beam is composed of graphene-reinforced with glass fiber-reinforced polymer (GFRP) composite skins and a GFRP strip-reinforced honeycomb core. The governing equations are developed by using the finite element formulation along with the higher-order beam theory (HOBT). A significant degree of agreement is found when comparing numerical results to accessible literature. Additionally, this work examines the effects of graphene reinforcement, GFRP honeycomb core thickness, graphene-reinforced GFRP skin layer thickness, and end conditions on the vibration, damping, and buckling behavior of honeycomb sandwich beams. The sandwich beam with graphene-reinforced skins outperforms the neat sandwich beam in terms of natural frequency, damping, and buckling, with improvements of 8.04%, 10.56%, and 18.29%, respectively. The lightweight GFRP honeycomb core, combined with the advanced graphene-reinforced composite face sheets, offers interesting applications and further research.
- Open Access
- 10 October 2022
- Published by Wiley in Advances in Materials Science and Engineering
- Vol. 2022, 1-9
An AHP-TOPSIS Approach for Optimizing the Mechanical Performance of Natural Fiber-Based Green Composites
Natural fibers have emerged as an effective replacement for synthetic fibers in the fabrication of green composites to be used for producing various components in automotive, aerospace, and other applications. In this proposed study, the mechanical properties of banana and coir fiber-based green composites have been optimized by using a hybrid AHP-TOPSIS approach. Corn starch along with glycerol has been used as the matrix material for fabricating the green composites. The mechanical properties such as tensile strength, flexural strength, and impact strength of the developed green composite have been optimized with a focus on the utilization of this composite in automotive and aerospace applications. Three different weight percentages (0%, 5%, and 10%) of banana and coir fibers was considered for the fabrication of green composites. The constituents of the green composite have been taken as the input variables whereas the mechanical properties of the green composite are considered as the output variables for designing the experiment. The design of the experiment consisted of nine different combinations of input and output variables. Results of the study revealed that 5 wt.% of banana fiber, 10 wt.% of coir fiber, and 85 wt.% of corn starch provide the optimum mechanical performance of the developed green composites.
- 10 October 2022
- Published by Wiley in Advances in Materials Science and Engineering
- Vol. 2022, 1-9
Open AccessAn AHP-TOPSIS Approach for Optimizing the Mechanical Performance of Natural Fiber-Based Green Composites
Natural fibers have emerged as an effective replacement for synthetic fibers in the fabrication of green composites to be used for producing various components in automotive, aerospace, and other applications. In this proposed study, the mechanical properties of banana and coir fiber-based green composites have been optimized by using a hybrid AHP-TOPSIS approach. Corn starch along with glycerol has been used as the matrix material for fabricating the green composites. The mechanical properties such as tensile strength, flexural strength, and impact strength of the developed green composite have been optimized with a focus on the utilization of this composite in automotive and aerospace applications. Three different weight percentages (0%, 5%, and 10%) of banana and coir fibers was considered for the fabrication of green composites. The constituents of the green composite have been taken as the input variables whereas the mechanical properties of the green composite are considered as the output variables for designing the experiment. The design of the experiment consisted of nine different combinations of input and output variables. Results of the study revealed that 5 wt.% of banana fiber, 10 wt.% of coir fiber, and 85 wt.% of corn starch provide the optimum mechanical performance of the developed green composites.
- Open Access
- 1 January 2021
- Published by Wiley in Advances in Materials Science and Engineering
- Vol. 2021 (1)
Investigation on Processing Maps of Diffusion Bonding Process Parameters for Ti‐6Al‐4 V/AISI304 Dissimilar Joints
The diffusion bonding (DB) method is used in this investigation to connect high‐temperature dissimilar materials. The existence of difficult‐to‐remove oxide coatings on the titanium surfaces, as well as the arrangement of breakable metallic interlayers and oxide enclosures inside the bond region, provides the most significant challenges during the transition from AISI304 to Ti‐6Al‐4V alloying. In addition, an effort was made to advance DB processing maps for the operational connection of Ti‐6Al‐4V to AISI304 alloys to improve their performance. Joints had been created by combining several process factors, such as bonding temperature (T), bonding pressure (P), and holding time (t), to create diverse designs. Based on the findings, database processing maps were created. This set of processing maps may be used as a rough guideline for selecting appropriate DB process parameters for generating virtuous excellent bonds between Ti‐6Al‐4V and AISI304 alloys. The maximum lap shear strength (LSS) was achieved at 800°C, 15 MPa, and 45 min.
- 1 January 2021
- Published by Wiley in Advances in Materials Science and Engineering
- Vol. 2021 (1)
Open AccessInvestigation on Processing Maps of Diffusion Bonding Process Parameters for Ti‐6Al‐4 V/AISI304 Dissimilar Joints
The diffusion bonding (DB) method is used in this investigation to connect high‐temperature dissimilar materials. The existence of difficult‐to‐remove oxide coatings on the titanium surfaces, as well as the arrangement of breakable metallic interlayers and oxide enclosures inside the bond region, provides the most significant challenges during the transition from AISI304 to Ti‐6Al‐4V alloying. In addition, an effort was made to advance DB processing maps for the operational connection of Ti‐6Al‐4V to AISI304 alloys to improve their performance. Joints had been created by combining several process factors, such as bonding temperature (T), bonding pressure (P), and holding time (t), to create diverse designs. Based on the findings, database processing maps were created. This set of processing maps may be used as a rough guideline for selecting appropriate DB process parameters for generating virtuous excellent bonds between Ti‐6Al‐4V and AISI304 alloys. The maximum lap shear strength (LSS) was achieved at 800°C, 15 MPa, and 45 min.
- RetractedOpen Access
- 1 January 2021
- Published by Wiley in Advances in Materials Science and Engineering
- Vol. 2021 (1)
[Retracted] Multiobjective Optimization of Mechanical Properties on Sisal‐Glass Fiber‐Reinforced Hybrid Composites Using Response Surface Methodology and LINGO Analysis
The aim of this research work was to develop the optimal mechanical properties, namely, tensile strength, flexural strength, and impact strength of sisal and glass fiber‐reinforced polymer hybrid composites. The sisal, in the form of short fiber, is randomly used as reinforcements for composite materials, which is rich in cellulose, economical, and easily available as well as glass fibers have low cost and have good mechanical properties. In addition, epoxy resin and hardener were for the fabrication of composites by compression molding. The selected materials are fabricated by compression molding in various concentrations on volume basics. The combination of material compositions is obtained from the design of experiments and optimum parameters determined by the Response Surface Methodology (RSM). From the investigation of mechanical properties, the sisal is the most significant factor and verified by ANOVA techniques. The multiobjective optimal levels of factors are obtained by LINGO analysis.
- 1 January 2021
- Published by Wiley in Advances in Materials Science and Engineering
- Vol. 2021 (1)
RetractedOpen Access[Retracted] Multiobjective Optimization of Mechanical Properties on Sisal‐Glass Fiber‐Reinforced Hybrid Composites Using Response Surface Methodology and LINGO Analysis
The aim of this research work was to develop the optimal mechanical properties, namely, tensile strength, flexural strength, and impact strength of sisal and glass fiber‐reinforced polymer hybrid composites. The sisal, in the form of short fiber, is randomly used as reinforcements for composite materials, which is rich in cellulose, economical, and easily available as well as glass fibers have low cost and have good mechanical properties. In addition, epoxy resin and hardener were for the fabrication of composites by compression molding. The selected materials are fabricated by compression molding in various concentrations on volume basics. The combination of material compositions is obtained from the design of experiments and optimum parameters determined by the Response Surface Methodology (RSM). From the investigation of mechanical properties, the sisal is the most significant factor and verified by ANOVA techniques. The multiobjective optimal levels of factors are obtained by LINGO analysis.
- RetractedOpen Access
- 1 January 2021
- Published by Wiley in Advances in Materials Science and Engineering
- Vol. 2021 (1)
[Retracted] A Comparative Study on Crack‐Healing Ability of Al2O3/SiC Structural Ceramic Composites Synthesized by Microwave Sintering and Conventional Electrical Sintering
This study was conducted to assess and compare the crack‐healing ability of conventional electrical sintered and microwave sintered Al2O3/x wt. % SiC (x = 5, 10, 15, and 20) structural ceramic composites. The crack‐healing ability of both conventional electrical sintered and microwave sintered specimens was studied by introducing a crack of ∼100 µm length by Vickers’s indentation and conducting a heat treatment at 1200°C for dwell time of 1 h in air. The flexural or bending strength of sintered, cracked, and crack‐healed specimens was determined by three‐point bending test, and the phase variations by X‐ray diffraction and SEM micrographs before and after crack‐healing of both the sintering methods were studied and compared. The results show that almost all the specimens recovered their strength after crack‐healing, but the strength of microwave sintered Al2O3/SiC structural ceramic composites has been shown to be better than that of conventional electrical sintered Al2O3/SiC structural ceramic composites. The microwave sintered crack‐healed Al2O3/10 wt. % SiC specimen shows higher flexural strength of 794 MPa, which was 105% when compared with conventional electrical sintered Al2O3/10 wt. % SiC and crack‐healed Al2O3/10 wt. % SiC specimen. It was found by X‐ray diffractogram that before crack‐healing, all the conventional electrical sintered samples have SiO2 phase which reduce the crack‐healing ability and microwave sintered samples with 15 and 20 wt. % SiC show lesser SiO2 phase and 5 and 10 wt. % SiC samples have no SiO2 phase before crack‐healing. However, after crack‐healing treatment, all the samples have distinct SiO2 phase along with Al2O3 and SiC phases. Microwave sintered Al2O3/10 wt. % SiC specimen cracks were fully healed which was evident in SEM micrographs.
- 1 January 2021
- Published by Wiley in Advances in Materials Science and Engineering
- Vol. 2021 (1)
RetractedOpen Access[Retracted] A Comparative Study on Crack‐Healing Ability of Al2O3/SiC Structural Ceramic Composites Synthesized by Microwave Sintering and Conventional Electrical Sintering
This study was conducted to assess and compare the crack‐healing ability of conventional electrical sintered and microwave sintered Al2O3/x wt. % SiC (x = 5, 10, 15, and 20) structural ceramic composites. The crack‐healing ability of both conventional electrical sintered and microwave sintered specimens was studied by introducing a crack of ∼100 µm length by Vickers’s indentation and conducting a heat treatment at 1200°C for dwell time of 1 h in air. The flexural or bending strength of sintered, cracked, and crack‐healed specimens was determined by three‐point bending test, and the phase variations by X‐ray diffraction and SEM micrographs before and after crack‐healing of both the sintering methods were studied and compared. The results show that almost all the specimens recovered their strength after crack‐healing, but the strength of microwave sintered Al2O3/SiC structural ceramic composites has been shown to be better than that of conventional electrical sintered Al2O3/SiC structural ceramic composites. The microwave sintered crack‐healed Al2O3/10 wt. % SiC specimen shows higher flexural strength of 794 MPa, which was 105% when compared with conventional electrical sintered Al2O3/10 wt. % SiC and crack‐healed Al2O3/10 wt. % SiC specimen. It was found by X‐ray diffractogram that before crack‐healing, all the conventional electrical sintered samples have SiO2 phase which reduce the crack‐healing ability and microwave sintered samples with 15 and 20 wt. % SiC show lesser SiO2 phase and 5 and 10 wt. % SiC samples have no SiO2 phase before crack‐healing. However, after crack‐healing treatment, all the samples have distinct SiO2 phase along with Al2O3 and SiC phases. Microwave sintered Al2O3/10 wt. % SiC specimen cracks were fully healed which was evident in SEM micrographs.
- RetractedOpen Access
- 1 January 2021
- Published by Wiley in Advances in Materials Science and Engineering
- Vol. 2021 (1)
[Retracted] Computational Investigations of Fixed‐Free and Fixed‐Fixed Types Single‐Wall Carbon Nanotube Mass Sensing Biosensor
Using carbon nanotubes for sensing the mass in a biosensor is recently proven as an emerging technology in healthcare industry. This study investigates relative frequency shifts and sensitivity studies of various biological objects such as insulin hormone, immunoglobulin G (IgG), the most abundant type of antibody, and low‐density lipoproteins (LDL) masses using the single‐wall carbon nanotubes as a biomass sensor via continuum mechanics. Uniform distributed mass is applied to the single‐wall carbon nanotube mass sensor. In this study, fixed‐free and fixed‐fixed type single‐wall carbon nanotubes with various lengths of relative frequency shifts are studied. Additionally, the sensitivity analysis of fixed‐free and fixed‐fixed type CNT biological mass sensors is carried out. Moreover, mode shapes studies are performed. The sensitivity results show better, if the length of the single‐wall carbon nanotube is reduced.
- 1 January 2021
- Published by Wiley in Advances in Materials Science and Engineering
- Vol. 2021 (1)
RetractedOpen Access[Retracted] Computational Investigations of Fixed‐Free and Fixed‐Fixed Types Single‐Wall Carbon Nanotube Mass Sensing Biosensor
Using carbon nanotubes for sensing the mass in a biosensor is recently proven as an emerging technology in healthcare industry. This study investigates relative frequency shifts and sensitivity studies of various biological objects such as insulin hormone, immunoglobulin G (IgG), the most abundant type of antibody, and low‐density lipoproteins (LDL) masses using the single‐wall carbon nanotubes as a biomass sensor via continuum mechanics. Uniform distributed mass is applied to the single‐wall carbon nanotube mass sensor. In this study, fixed‐free and fixed‐fixed type single‐wall carbon nanotubes with various lengths of relative frequency shifts are studied. Additionally, the sensitivity analysis of fixed‐free and fixed‐fixed type CNT biological mass sensors is carried out. Moreover, mode shapes studies are performed. The sensitivity results show better, if the length of the single‐wall carbon nanotube is reduced.
- 19 February 2020
- Published by Springer Nature
- p. 1-13
Anchorage System for Penstocks—Case Study of Champawat Town Pumping Water Supply Scheme
- 19 February 2020
- Published by Springer Nature
- p. 1-13
Anchorage System for Penstocks—Case Study of Champawat Town Pumping Water Supply Scheme