Aleksey Pudov
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Aleksey Pudov has a total of 107 co-authors. Here are the top co-authors by number of shared publications:
- Alexandr V. Rybka
National Science Ctr. Kharkov Institute of Physics and Technology (Ukraine)
11 shared publications - Vladimir E. Kutny
National Science Ctr. Kharkov Institute of Physics and Technology (Ukraine)
11 shared publications - S. A. Sokolov
National Science Center “Kharkov Institute of Physics and Technology” 2 , 1 Akademicheskaya St., Kharkov 61108, Ukraine
7 shared publications J.R. Sites
Colorado State University, FT. Collins, CO, USA
5 shared publicationsL. Davydov
National Science Center “Kharkov Institute of Physics and Technology
4 shared publicationsGregory Brown
Nanosolar Inc., San Jose, California, USA
3 shared publications
Latest Publications
- Open Access
- 15 December 2023
- Published by AIP Publishing in Journal of Applied Physics
- Vol. 134 (23)
Simulation of thin-film detectors of ionizing radiation and thermal neutrons based on CdTe
The article is dedicated to the numerical simulations of thin-layer structures based on CdTe semiconductors, which can be fabricated by using low-cost technologies. Structures Mo/Au/CdS/CdTe/Au, and their modifications, with different thicknesses of the main layers are investigated. The possibility of creating a detector of ionizing radiation based on these structures, which has selective properties with respect to the radiation type, and very low operation voltage, is shown. The detection efficiencies of α-, β-, and γ-radiation in different energy ranges were calculated based on the obtained values of energy losses of ionizing particles, which are proportional to the output signal of the detector. The use of such detectors, together with a solid-state converter made of boron carbide containing either natural boron natB or boron enriched with the 10B isotope up to 95%, for the detection of thermal neutrons was also studied. It was shown that the structures could be used to create α-particle spectrometers, given that the CdTe thickness is tailored to the highest expected α-particle energy. Detectors with thin CdTe (1–5 μm) can be successfully used in the counting mode. For neutron detection, stacking multiple single structures into sandwich structures was proposed and investigated. In such a configuration, the detector qualities were markedly improved: the efficiency of neutron detection reached ∼60%, while the sensitivity to the background γ- and β-radiation was ∼100 times lower than that for neutrons. The very low sensitivity of the simulated neutron detectors to the neutron incidence angle was shown.
- 15 December 2023
- Published by AIP Publishing in Journal of Applied Physics
- Vol. 134 (23)
Open AccessSimulation of thin-film detectors of ionizing radiation and thermal neutrons based on CdTe
The article is dedicated to the numerical simulations of thin-layer structures based on CdTe semiconductors, which can be fabricated by using low-cost technologies. Structures Mo/Au/CdS/CdTe/Au, and their modifications, with different thicknesses of the main layers are investigated. The possibility of creating a detector of ionizing radiation based on these structures, which has selective properties with respect to the radiation type, and very low operation voltage, is shown. The detection efficiencies of α-, β-, and γ-radiation in different energy ranges were calculated based on the obtained values of energy losses of ionizing particles, which are proportional to the output signal of the detector. The use of such detectors, together with a solid-state converter made of boron carbide containing either natural boron natB or boron enriched with the 10B isotope up to 95%, for the detection of thermal neutrons was also studied. It was shown that the structures could be used to create α-particle spectrometers, given that the CdTe thickness is tailored to the highest expected α-particle energy. Detectors with thin CdTe (1–5 μm) can be successfully used in the counting mode. For neutron detection, stacking multiple single structures into sandwich structures was proposed and investigated. In such a configuration, the detector qualities were markedly improved: the efficiency of neutron detection reached ∼60%, while the sensitivity to the background γ- and β-radiation was ∼100 times lower than that for neutrons. The very low sensitivity of the simulated neutron detectors to the neutron incidence angle was shown.
- Open Access
- 12 October 2023
- Published by Problems of Atomic Science and Technology in Problems of Atomic Science and Technology
- No. 5,p. 146-151
PROPORTIONAL DETECTORS OF GAMMA-RADIATION BASED ON HIGH PURITY XENON GAS FOR RADIATION MONITORING
This article is dedicated to a detailed investigation of properties of a proportional counter based on the Xe+2%CH4 mixture. A setup for filling the detectors with high purity Xe gas and Xe-based gas mixtures was designed and made. An optimized design of the proportional counters was developed and investigated. The design parameters, such as the material and diameter of the anode, the number and material of the gas mixture inlets, composition and pressure of the gas were improved. The operating regimes of the proportional counters, as well as their thermal stability, were investigated.
- 12 October 2023
- Published by Problems of Atomic Science and Technology in Problems of Atomic Science and Technology
- No. 5,p. 146-151
Open AccessPROPORTIONAL DETECTORS OF GAMMA-RADIATION BASED ON HIGH PURITY XENON GAS FOR RADIATION MONITORING
This article is dedicated to a detailed investigation of properties of a proportional counter based on the Xe+2%CH4 mixture. A setup for filling the detectors with high purity Xe gas and Xe-based gas mixtures was designed and made. An optimized design of the proportional counters was developed and investigated. The design parameters, such as the material and diameter of the anode, the number and material of the gas mixture inlets, composition and pressure of the gas were improved. The operating regimes of the proportional counters, as well as their thermal stability, were investigated.
- Open Access
- 9 July 2023
- Published by National Technical University Kharkiv Polytechnic Institute in Bulletin of the National Technical University "KhPI". Series: Energy: Reliability and Energy Efficiency
- No. 1 (6),p. 105-112
Effect of pulsed hydrogen and helium plasma irradiation on the formation of solid solutions in the thin-film CdTe/CdS heterosystem
The interphase interaction of cadmium sulfide and cadmium telluride thin film layers under irradiation with pulses of hydrogen and helium plasma was investigated by the X-ray diffraction method. CdS/CdTe heterosystem samples were obtained by the hot wall method on glass substrates with a transparent FTO electrode. During deposition of CdS layers 0.3–0.32 µm thick, the temperature of the evaporator zone was 590 °C, and the substrate temperature was 395 °C. CdTe layers 3.8–4.0 µm thick were deposited at an evaporation zone temperature of 520 °C and a substrate temperature of 497 °C. After deposition, the “chloride” treatment of the heterosystem was carried out. The “chloride” treatment consisted in the deposition of a cadmium chloride film 0.7 μm thick on the surface of a CdTe by thermal vacuum evaporation without heating the substrate and by annealing the entire structure in air at a temperature of 410-415 °C for 20 min. The composition of the solid solutions was determined from the lattice period according to Vegard's rule. In the initial state, along with the cubic phase of cadmium telluride, the presence of CdTe1-xSx solid solutions with a sulfur concentration of 3 % and 8.2 % is observed. After irradiation of the CdS/CdTe heterosystems with hydrogen plasma pulses, the entire base layer turned into a solid solution with a sulfur concentration of 3 %. At the same time, two more phases of CdTe1-xSx solid solutions with sulfur concentrations of 6 % and 11.5 % were observed. The relative concentration of the cadmium telluride phase in the initial state was 84 %, after irradiation with hydrogen plasma pulses it was 82 %. In the initial state, the phases of solid solutions with sulfur content of 3 % and 8.2 % had relative concentrations of 7 % and 9 %, respectively; after irradiation, their relative concentrations became 15 % and 3 %, respectively. After irradiation of the CdS/CdTe heterosystem with helium plasma pulses, the entire base layer turned into a solid solution with a sulfur concentration of 1.5 %. In this case, two more phases with a sulfur concentration of 3.7 % and 7.9 % were observed. The relative concentration of cadmium phase telluride after irradiation with hydrogen plasma pulses decreases to 79 %. After irradiation, the relative concentration of the phase of solid solutions with sulfur contents of 3 % and 8.2 % increases to 17 % and 12 %, respectively. The experimentally observed difference in the evolution of the phase composition of the CdS/CdTe film heterosystem under irradiation with hydrogen and helium plasma pulses may be due to the fact that irradiation with more massive helium atoms leads to a greater thermal effect, which causes melting.
- 9 July 2023
- Published by National Technical University Kharkiv Polytechnic Institute in Bulletin of the National Technical University "KhPI". Series: Energy: Reliability and Energy Efficiency
- No. 1 (6),p. 105-112
Open AccessEffect of pulsed hydrogen and helium plasma irradiation on the formation of solid solutions in the thin-film CdTe/CdS heterosystem
The interphase interaction of cadmium sulfide and cadmium telluride thin film layers under irradiation with pulses of hydrogen and helium plasma was investigated by the X-ray diffraction method. CdS/CdTe heterosystem samples were obtained by the hot wall method on glass substrates with a transparent FTO electrode. During deposition of CdS layers 0.3–0.32 µm thick, the temperature of the evaporator zone was 590 °C, and the substrate temperature was 395 °C. CdTe layers 3.8–4.0 µm thick were deposited at an evaporation zone temperature of 520 °C and a substrate temperature of 497 °C. After deposition, the “chloride” treatment of the heterosystem was carried out. The “chloride” treatment consisted in the deposition of a cadmium chloride film 0.7 μm thick on the surface of a CdTe by thermal vacuum evaporation without heating the substrate and by annealing the entire structure in air at a temperature of 410-415 °C for 20 min. The composition of the solid solutions was determined from the lattice period according to Vegard's rule. In the initial state, along with the cubic phase of cadmium telluride, the presence of CdTe1-xSx solid solutions with a sulfur concentration of 3 % and 8.2 % is observed. After irradiation of the CdS/CdTe heterosystems with hydrogen plasma pulses, the entire base layer turned into a solid solution with a sulfur concentration of 3 %. At the same time, two more phases of CdTe1-xSx solid solutions with sulfur concentrations of 6 % and 11.5 % were observed. The relative concentration of the cadmium telluride phase in the initial state was 84 %, after irradiation with hydrogen plasma pulses it was 82 %. In the initial state, the phases of solid solutions with sulfur content of 3 % and 8.2 % had relative concentrations of 7 % and 9 %, respectively; after irradiation, their relative concentrations became 15 % and 3 %, respectively. After irradiation of the CdS/CdTe heterosystem with helium plasma pulses, the entire base layer turned into a solid solution with a sulfur concentration of 1.5 %. In this case, two more phases with a sulfur concentration of 3.7 % and 7.9 % were observed. The relative concentration of cadmium phase telluride after irradiation with hydrogen plasma pulses decreases to 79 %. After irradiation, the relative concentration of the phase of solid solutions with sulfur contents of 3 % and 8.2 % increases to 17 % and 12 %, respectively. The experimentally observed difference in the evolution of the phase composition of the CdS/CdTe film heterosystem under irradiation with hydrogen and helium plasma pulses may be due to the fact that irradiation with more massive helium atoms leads to a greater thermal effect, which causes melting.
- 9 September 2022
- Published by AIP Publishing in Journal of Applied Physics
- Vol. 132 (10) , 104501
Radiation sensor based on thin-film CdTe/CdS device structure and its radiation resistance under high-intensity hydrogen plasma
In this work, the ability of CdTe/CdS thin-film device structures prepared by the hot-wall method to detect ionizing radiation was investigated. The samples were fabricated with a structure typical of CdTe/CdS-based solar cells and exhibit radiation sensitivity even without the application of an external voltage. This allows such structures to be used as low-voltage radiation sensors. An investigation of the radiation resistance of the structures, namely, the effect of irradiation with high-intensity hydrogen plasma H2+ on the crystal structure and performance, was carried out. It was shown that the device structures remained operational after two plasma pulses at an ion density of 2 × 1023 m−2 and an energy density of up to 0.2 MJ/m2. With further exposure to plasma, the device structures deteriorated, first, due to gradual sputtering off of the back contact, and, second, as a result of diffusion processes that occurred when the structures were heated to high temperatures, due to which the entire volume of the CdTe base layer got converted into a CdSxTe1−x solid solution.
- 9 September 2022
- Published by AIP Publishing in Journal of Applied Physics
- Vol. 132 (10) , 104501
Radiation sensor based on thin-film CdTe/CdS device structure and its radiation resistance under high-intensity hydrogen plasma
In this work, the ability of CdTe/CdS thin-film device structures prepared by the hot-wall method to detect ionizing radiation was investigated. The samples were fabricated with a structure typical of CdTe/CdS-based solar cells and exhibit radiation sensitivity even without the application of an external voltage. This allows such structures to be used as low-voltage radiation sensors. An investigation of the radiation resistance of the structures, namely, the effect of irradiation with high-intensity hydrogen plasma H2+ on the crystal structure and performance, was carried out. It was shown that the device structures remained operational after two plasma pulses at an ion density of 2 × 1023 m−2 and an energy density of up to 0.2 MJ/m2. With further exposure to plasma, the device structures deteriorated, first, due to gradual sputtering off of the back contact, and, second, as a result of diffusion processes that occurred when the structures were heated to high temperatures, due to which the entire volume of the CdTe base layer got converted into a CdSxTe1−x solid solution.
- 27 June 2020
- Published by Springer Nature
- p. 229-243
Hand-Held Gamma Detector Based on High-Pressure Xenon Gas: Determination of Charge Carrier Lifetime in Xe
- 27 June 2020
- Published by Springer Nature
- p. 229-243
Hand-Held Gamma Detector Based on High-Pressure Xenon Gas: Determination of Charge Carrier Lifetime in Xe
- 30 January 2020
- Published by Problems of Atomic Science and Technology
- p. 211-214
MINERAL INSULATORS FOR KOMPTON DETECTORS OF NEUTRONS WITH A METAL HAFNIUM EMITTER
One of the priority tasks of nuclear power industry is to increase the reliability and safety of nuclear power plants. In this regard, traditional detectors for measuring the neutron flux in the reactor core are being improved and new ones are developed. This work is dedicated to one of the tasks of creating a compton self-powered neutron detector, namely, the formation of an insulator of magnesium oxide on an emitter of metallic hafnium. The effect of three types of magnesium oxide of different purity and structural state, as well as annealing temperature on the electrical resistance of the insulator between the collector and the emitter of the detector, is studied. The detector prototypes were manufactured by filling with magnesium oxidepowders or by applying liquid-phase mixturesthereof.
- 30 January 2020
- Published by Problems of Atomic Science and Technology
- p. 211-214
MINERAL INSULATORS FOR KOMPTON DETECTORS OF NEUTRONS WITH A METAL HAFNIUM EMITTER
One of the priority tasks of nuclear power industry is to increase the reliability and safety of nuclear power plants. In this regard, traditional detectors for measuring the neutron flux in the reactor core are being improved and new ones are developed. This work is dedicated to one of the tasks of creating a compton self-powered neutron detector, namely, the formation of an insulator of magnesium oxide on an emitter of metallic hafnium. The effect of three types of magnesium oxide of different purity and structural state, as well as annealing temperature on the electrical resistance of the insulator between the collector and the emitter of the detector, is studied. The detector prototypes were manufactured by filling with magnesium oxidepowders or by applying liquid-phase mixturesthereof.
- Open Access
- 1 December 2019
- Published by Elsevier in Nuclear Engineering and Technology
- Vol. 51 (8) , 1964-1969
Radiation-induced transformation of Hafnium composition
- 1 December 2019
- Published by Elsevier in Nuclear Engineering and Technology
- Vol. 51 (8) , 1964-1969
Open AccessRadiation-induced transformation of Hafnium composition
- Open Access
- 25 September 2018
- Published by National Academy of Sciences of Ukraine (Co. LTD Ukrinformnauka) in Nuclear Physics and Atomic Energy
- Vol. 19 (3) , 237-243
Compton-emissive hafnium detector of neutrons for in-core monitoring
- 25 September 2018
- Published by National Academy of Sciences of Ukraine (Co. LTD Ukrinformnauka) in Nuclear Physics and Atomic Energy
- Vol. 19 (3) , 237-243
Open AccessCompton-emissive hafnium detector of neutrons for in-core monitoring