Sajjad Yousefian
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Sajjad Yousefian has a total of 29 co-authors. Here are the top co-authors by number of shared publications:
- Rory F. D. Monaghan
National University of Ireland, Galway, Ireland
11 shared publications - Gilles Bourque
Department of Mechanical Engineering, McGill University , Montreal, QC H3A 0G4, Canada
4 shared publications Gilles Bourque
Siemens Canada Ltd, 9545 Cote de Liesse Road, Montreal, QC H9P 1A5, Canada; Department of Mechanical Engineering, McGill University, Montréal, QC H3A 0C3, Canada
3 shared publications- Sandeep Jella
Siemens Energy Canada Limited , Dorval, QC H9P 1A5, Canada
3 shared publications - Ashish Vashishtha
South East Technological University - Carlow
2 shared publications - Eoin M. Burke
Mechanical Engineering, National University of Ireland Galway, Galway H91 HX31, Ireland; Ryan Institute for Marine, Environmental and Energy Research, National University of Ireland Galway, Galway H91 TK33, Ireland; MaREI,SFI Research Centre for Energy, Climate and Marine, Environmental Research Institute, Beaufort Building, University College Cork, Cork P43 C573, Ireland
2 shared publications
Latest Publications
- 4 October 2022
- Published by ASME International in Journal of Engineering for Gas Turbines and Power
- Vol. 144 (12)
Quantification of Autoignition Risk in Aeroderivative Gas Turbine Premixers Using Incompletely Stirred Reactor and Surrogate Modeling
The design and operation of premixers for gas turbines must deal with the possibility of relatively rare events causing dangerous autoignition (AI). Rare AI events may occur in the presence of fluctuations of operational parameters, such as temperature and fuel composition, and must be understood and predicted. This work presents a methodology based on incompletely stirred reactor (ISR) and surrogate modeling to increase efficiency and feasibility in premixer design optimization for rare events. For a representative premixer, a space-filling design is used to sample the variability of three influential operational parameters. An ISR is reconstructed and solved in a postprocessing fashion for each sample, leveraging a well-resolved computational fluid dynamics solution of the non-reacting flow inside the premixer. Via detailed chemistry and reduced computational costs, ISR tracks the evolution of AI precursors and temperature conditioned on a mixture fraction. Accurate surrogate models are then trained for selected AI metrics on all ISR samples. The final quantification of the AI probability is achieved by querying the surrogate models via Monte Carlo sampling of the random parameters. The approach is fast and reliable so that user-controllable, independent variables can be optimized to maximize system performance while observing a constraint on the allowable probability of AI.
- 4 October 2022
- Published by ASME International in Journal of Engineering for Gas Turbines and Power
- Vol. 144 (12)
Quantification of Autoignition Risk in Aeroderivative Gas Turbine Premixers Using Incompletely Stirred Reactor and Surrogate Modeling
The design and operation of premixers for gas turbines must deal with the possibility of relatively rare events causing dangerous autoignition (AI). Rare AI events may occur in the presence of fluctuations of operational parameters, such as temperature and fuel composition, and must be understood and predicted. This work presents a methodology based on incompletely stirred reactor (ISR) and surrogate modeling to increase efficiency and feasibility in premixer design optimization for rare events. For a representative premixer, a space-filling design is used to sample the variability of three influential operational parameters. An ISR is reconstructed and solved in a postprocessing fashion for each sample, leveraging a well-resolved computational fluid dynamics solution of the non-reacting flow inside the premixer. Via detailed chemistry and reduced computational costs, ISR tracks the evolution of AI precursors and temperature conditioned on a mixture fraction. Accurate surrogate models are then trained for selected AI metrics on all ISR samples. The final quantification of the AI probability is achieved by querying the surrogate models via Monte Carlo sampling of the random parameters. The approach is fast and reliable so that user-controllable, independent variables can be optimized to maximize system performance while observing a constraint on the allowable probability of AI.
- Open Access
- 30 September 2022
- Published by Elsevier in European Journal of Mechanics - B/Fluids
- Vol. 97, 93-110
Computational design and experimental analysis of a novel visor for COVID-19 patients receiving high-flow nasal oxygen therapy
- 30 September 2022
- Published by Elsevier in European Journal of Mechanics - B/Fluids
- Vol. 97, 93-110
Open AccessComputational design and experimental analysis of a novel visor for COVID-19 patients receiving high-flow nasal oxygen therapy
- Open Access
- 16 July 2021
- Published by ASME International
An Optimized Correlation for Turbulent Flame Speed for C1-C3 Fuels at Engines-Relevant Conditions
An Optimized Correlation for Turbulent Flame Speed for C~1~- C~3~ Fuels at Engines-Relevant Conditions Abstract The aim of this work is to examine the state-of-the-art turbulent flame speed correlations and optimize their adjustable parameters to best match a wide range experimental turbulent premixed combustion results. Based on previous work, four correlations have been
- 16 July 2021
- Published by ASME International
Open AccessAn Optimized Correlation for Turbulent Flame Speed for C1-C3 Fuels at Engines-Relevant Conditions
An Optimized Correlation for Turbulent Flame Speed for C~1~- C~3~ Fuels at Engines-Relevant Conditions Abstract The aim of this work is to examine the state-of-the-art turbulent flame speed correlations and optimize their adjustable parameters to best match a wide range experimental turbulent premixed combustion results. Based on previous work, four correlations have been
- Open Access
- 16 July 2021
- Published by ASME International
CFD-CRN Study of NOX formatio in a High-Pressure Combustor Fired With Lean Premixed CH4 / H2 --Air Mixtures
A hybrid approach of CFD-CRN have been found useful in predicting pollutants for many combustion systems \[3\] without incurring very high computational costs. In this approach, flow field and major species are computed using CFD with reduced kinetic mechanism. Further, a chemical reactor network is constructed based on CFD simulation and solved with detailed chemical kinetic- 16 July 2021
- Published by ASME International
Open AccessCFD-CRN Study of NOX formatio in a High-Pressure Combustor Fired With Lean Premixed CH4 / H2 --Air Mixtures
A hybrid approach of CFD-CRN have been found useful in predicting pollutants for many combustion systems \[3\] without incurring very high computational costs. In this approach, flow field and major species are computed using CFD with reduced kinetic mechanism. Further, a chemical reactor network is constructed based on CFD simulation and solved with detailed chemical kinetic - Open Access
- 1 July 2021
- Published by Elsevier in International Journal of Hydrogen Energy
- Vol. 46 (46) , 23927-23942
Bayesian inference and uncertainty quantification for hydrogen-enriched and lean-premixed combustion systems
- 1 July 2021
- Published by Elsevier in International Journal of Hydrogen Energy
- Vol. 46 (46) , 23927-23942
Open AccessBayesian inference and uncertainty quantification for hydrogen-enriched and lean-premixed combustion systems
- 15 October 2020
- Published by ASME International in Journal of Engineering for Gas Turbines and Power
- Vol. 142 (11)
An Optimized Correlation for Turbulent Flame Speed for C1–C3 Fuels at Engine-Relevant Conditions
The aim of this work is to examine the state-of-the-art turbulent flame speed (ST) correlations and optimize their adjustable parameters to best match a wide range experimental turbulent premixed combustion results. Four correlations based on previous works by Zimont, Kobayashi, Ronney and Muppala have been selected for the present study. Using a Matlab-based Nelder-Mead simplex direct search method, each correlation's adjustable parameters are optimized such that their mean absolute percentage error (MAPE) is minimized. In addition to the literature correlations, a new empirical correlation is developed using the same search method to define constants and powers in the expression. Two sets of optimized parameters are proposed to account for atmospheric and elevated (0.2-3.0 MPa) pressure flames. Each correlation is tested further, examining their ability to match ST trends for varying equivalence ratio (ϕ) and turbulent velocity ratio (u'/SL). It was found that a minimum of two correlations and two sets of adjustable parameters are required to accurately account for the entire range of data, thus showing that there is currently no turbulent flame speed correlation that is applicable across all engine-relevant conditions.
- 15 October 2020
- Published by ASME International in Journal of Engineering for Gas Turbines and Power
- Vol. 142 (11)
An Optimized Correlation for Turbulent Flame Speed for C1–C3 Fuels at Engine-Relevant Conditions
The aim of this work is to examine the state-of-the-art turbulent flame speed (ST) correlations and optimize their adjustable parameters to best match a wide range experimental turbulent premixed combustion results. Four correlations based on previous works by Zimont, Kobayashi, Ronney and Muppala have been selected for the present study. Using a Matlab-based Nelder-Mead simplex direct search method, each correlation's adjustable parameters are optimized such that their mean absolute percentage error (MAPE) is minimized. In addition to the literature correlations, a new empirical correlation is developed using the same search method to define constants and powers in the expression. Two sets of optimized parameters are proposed to account for atmospheric and elevated (0.2-3.0 MPa) pressure flames. Each correlation is tested further, examining their ability to match ST trends for varying equivalence ratio (ϕ) and turbulent velocity ratio (u'/SL). It was found that a minimum of two correlations and two sets of adjustable parameters are required to accurately account for the entire range of data, thus showing that there is currently no turbulent flame speed correlation that is applicable across all engine-relevant conditions.
- 21 September 2020
- Published by ASME International
CFD-CRN Study of NOx Formation in a High-Pressure Combustor Fired With Lean Premixed CH4 / H2 - Air Mixtures
The main motivation of this study is to investigate detailed NOx and CO formation in high-pressure dump combustor fired with lean premixed methane-air mixture using CFD-CRN hybrid approach. Further, this study is extended to investigate the effect of H2 enrichment on emission formation in the same combustor. Three-dimensional steady RANS CFD simulations have been performed using a Flamelet Generated Manifold (FGM) model in Simcenter STAR-CCM+ 2019.2 with the DRM22 reduced mechanism. The CFD simulations have been modelled along with all three heat transfers modes: conduction, convection and radiation. The conjugate heat transfer (CHT) approach and participating media radiation modelling have been used here. Initially, CFD simulations are performed for five lean equivalence ratios (ϕ = 0.43–0.55, Tinlet = 673 K, Vinlet = 40 m/s) of pure methane-air mixture operating at 5 bar. The exit temperature and flame-length are compared with available experimental data. The automatic chemical reactor network has been constructed from CFD data and solved using the recently developed reactor network module of Simcenter STAR-CCM+ 2019.2 in a single framework for each cases. It is found out that the CRNs up to 10,000 PSRs can provide adequate accuracy in exit NOx predictions compared to experiments for pure methane cases. The contribution of NOx formation pathway, changes from N2O intermediate to thermal NO as equivalence ratio increases. Further studies are performed for two equivalence ratios (ϕ = 0.43 and 0.50 to simulate the impact of H2 addition (up to 40% by volume) on NOx formation pathways and CO emission. It is found out here that the contribution from NNH pathway increases for leaner equivalence ratio cases (ϕ = 0.43), while thermal pathway slightly increases for ϕ = 0.50 with increase in H2 content from 0% to 40%.
- 21 September 2020
- Published by ASME International
CFD-CRN Study of NOx Formation in a High-Pressure Combustor Fired With Lean Premixed CH4 / H2 - Air Mixtures
The main motivation of this study is to investigate detailed NOx and CO formation in high-pressure dump combustor fired with lean premixed methane-air mixture using CFD-CRN hybrid approach. Further, this study is extended to investigate the effect of H2 enrichment on emission formation in the same combustor. Three-dimensional steady RANS CFD simulations have been performed using a Flamelet Generated Manifold (FGM) model in Simcenter STAR-CCM+ 2019.2 with the DRM22 reduced mechanism. The CFD simulations have been modelled along with all three heat transfers modes: conduction, convection and radiation. The conjugate heat transfer (CHT) approach and participating media radiation modelling have been used here. Initially, CFD simulations are performed for five lean equivalence ratios (ϕ = 0.43–0.55, Tinlet = 673 K, Vinlet = 40 m/s) of pure methane-air mixture operating at 5 bar. The exit temperature and flame-length are compared with available experimental data. The automatic chemical reactor network has been constructed from CFD data and solved using the recently developed reactor network module of Simcenter STAR-CCM+ 2019.2 in a single framework for each cases. It is found out that the CRNs up to 10,000 PSRs can provide adequate accuracy in exit NOx predictions compared to experiments for pure methane cases. The contribution of NOx formation pathway, changes from N2O intermediate to thermal NO as equivalence ratio increases. Further studies are performed for two equivalence ratios (ϕ = 0.43 and 0.50 to simulate the impact of H2 addition (up to 40% by volume) on NOx formation pathways and CO emission. It is found out here that the contribution from NNH pathway increases for leaner equivalence ratio cases (ϕ = 0.43), while thermal pathway slightly increases for ϕ = 0.50 with increase in H2 content from 0% to 40%.
- 20 September 2019
- Published by ASME International in Journal of Engineering for Gas Turbines and Power
- Vol. 141 (10)
Uncertainty Quantification of NOx and CO Emissions in a Swirl-Stabilized Burner
Uncertainty quantification (UQ) is becoming an essential attribute for development of computational tools in gas turbine combustion systems. Prediction of emissions with a variety of gaseous fuels and uncertain conditions requires probabilistic modeling tools, especially at part load conditions. The aim of this paper was to develop a computationally efficient tool to integrate uncertainty, sensitivity, and reliability analyses of CO and NOx emissions for a practical swirl-stabilized premixed burner. Sampling-based method (SBM), nonintrusive polynomial chaos expansion (NIPCE) based on point collocation method (PCM), Sobol sensitivity indices, and first-order reliability method (FORM) approaches are integrated with a chemical reactor network (CRN) model to develop a UQ-enabled emissions prediction tool. The CRN model consisting of a series of perfectly stirred reactors (PSRs) to model CO and NOx is constructed in Cantera. Surrogate models are developed using NIPCE-PCM approach and compared with the results of CRN model. The surrogate models are then used to perform global sensitivity and reliability analyses. The results show that the surrogate models substantially reduce the required computational costs by 2 to 3 orders of magnitude in comparison with the SBM to calculate sensitivity indices, importance factors and perform reliability analysis. Moreover, the results obtained by the NIPCE-PCM approach are more accurate in comparison with the SBM. Therefore, the developed UQ-enabled emissions prediction tool based on CRN and NIPCE-PCM approaches can be used for practical combustion systems as a reliable and computationally efficient framework to conduct probabilistic modeling of emissions.
- 20 September 2019
- Published by ASME International in Journal of Engineering for Gas Turbines and Power
- Vol. 141 (10)
Uncertainty Quantification of NOx and CO Emissions in a Swirl-Stabilized Burner
Uncertainty quantification (UQ) is becoming an essential attribute for development of computational tools in gas turbine combustion systems. Prediction of emissions with a variety of gaseous fuels and uncertain conditions requires probabilistic modeling tools, especially at part load conditions. The aim of this paper was to develop a computationally efficient tool to integrate uncertainty, sensitivity, and reliability analyses of CO and NOx emissions for a practical swirl-stabilized premixed burner. Sampling-based method (SBM), nonintrusive polynomial chaos expansion (NIPCE) based on point collocation method (PCM), Sobol sensitivity indices, and first-order reliability method (FORM) approaches are integrated with a chemical reactor network (CRN) model to develop a UQ-enabled emissions prediction tool. The CRN model consisting of a series of perfectly stirred reactors (PSRs) to model CO and NOx is constructed in Cantera. Surrogate models are developed using NIPCE-PCM approach and compared with the results of CRN model. The surrogate models are then used to perform global sensitivity and reliability analyses. The results show that the surrogate models substantially reduce the required computational costs by 2 to 3 orders of magnitude in comparison with the SBM to calculate sensitivity indices, importance factors and perform reliability analysis. Moreover, the results obtained by the NIPCE-PCM approach are more accurate in comparison with the SBM. Therefore, the developed UQ-enabled emissions prediction tool based on CRN and NIPCE-PCM approaches can be used for practical combustion systems as a reliable and computationally efficient framework to conduct probabilistic modeling of emissions.
- 1 October 2018
- Published by ASME International in Journal of Engineering for Gas Turbines and Power
- Vol. 140 (12)
Uncertainty Quantification of NOx Emission Due to Operating Conditions and Chemical Kinetic Parameters in a Premixed Burner
Many sources of uncertainty exist when emissions are modeled for a gas turbine combustion system. They originate from uncertain inputs, boundary conditions, calibration, or lack of sufficient fidelity in a model. In this paper, a nonintrusive polynomial chaos expansion (NIPCE) method is coupled with a chemical reactor network (CRN) model using Python to quantify uncertainties of NOx emission in a premixed burner. The first objective of uncertainty quantification (UQ) in this study is development of a global sensitivity analysis method based on the NIPCE method to capture aleatory uncertainty on NOx emission due to variation of operating conditions. The second objective is uncertainty analysis (UA) of NOx emission due to uncertain Arrhenius parameters in a chemical kinetic mechanism to study epistemic uncertainty in emission modeling. A two-reactor CRN consisting of a perfectly stirred reactor (PSR) and a plug flow reactor (PFR) is constructed in this study using Cantera to model NOx emission in a benchmark premixed burner under gas turbine operating conditions. The results of uncertainty and sensitivity analysis (SA) using NIPCE based on point collocation method (PCM) are then compared with the results of advanced Monte Carlo simulation (MCS). A set of surrogate models is also developed based on the NIPCE approach and compared with the forward model in Cantera to predict NOx emissions. The results show the capability of NIPCE approach for UQ using a limited number of evaluations to develop a UQ-enabled emission prediction tool for gas turbine combustion systems.
- 1 October 2018
- Published by ASME International in Journal of Engineering for Gas Turbines and Power
- Vol. 140 (12)
Uncertainty Quantification of NOx Emission Due to Operating Conditions and Chemical Kinetic Parameters in a Premixed Burner
Many sources of uncertainty exist when emissions are modeled for a gas turbine combustion system. They originate from uncertain inputs, boundary conditions, calibration, or lack of sufficient fidelity in a model. In this paper, a nonintrusive polynomial chaos expansion (NIPCE) method is coupled with a chemical reactor network (CRN) model using Python to quantify uncertainties of NOx emission in a premixed burner. The first objective of uncertainty quantification (UQ) in this study is development of a global sensitivity analysis method based on the NIPCE method to capture aleatory uncertainty on NOx emission due to variation of operating conditions. The second objective is uncertainty analysis (UA) of NOx emission due to uncertain Arrhenius parameters in a chemical kinetic mechanism to study epistemic uncertainty in emission modeling. A two-reactor CRN consisting of a perfectly stirred reactor (PSR) and a plug flow reactor (PFR) is constructed in this study using Cantera to model NOx emission in a benchmark premixed burner under gas turbine operating conditions. The results of uncertainty and sensitivity analysis (SA) using NIPCE based on point collocation method (PCM) are then compared with the results of advanced Monte Carlo simulation (MCS). A set of surrogate models is also developed based on the NIPCE approach and compared with the forward model in Cantera to predict NOx emissions. The results show the capability of NIPCE approach for UQ using a limited number of evaluations to develop a UQ-enabled emission prediction tool for gas turbine combustion systems.