Hemantha Kumar Yeddu
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Hemantha Kumar Yeddu has a total of 48 co-authors. Here are the top co-authors by number of shared publications:
- Annika Borgenstam
Department of Materials Science and Engineering, KTH Royal Institute of Technology, Stockholm, Sweden
8 shared publications John Ågren
7 shared publications- Turab Lookman
State Key Laboratory for Mechanical Behavior of Materials, Xi’an Jiaotong University, Xi’an, China
6 shared publications Avadh Saxena
Los Alamos National Laboratory
3 shared publicationsAmer Malik
2 shared publications- Bernardo Barbiellini
LUT University
2 shared publications
Latest Publications
- Open Access
- 29 August 2025
- Published by Elsevier in Computational Materials Science
- Vol. 260
Application of machine learning for predicting hydrogen-assisted fatigue crack growth
- 29 August 2025
- Published by Elsevier in Computational Materials Science
- Vol. 260
Open AccessApplication of machine learning for predicting hydrogen-assisted fatigue crack growth
- Open Access
- 29 March 2025
- Published by Springer Nature in Welding in the World
- Vol. 69 (7) , 2123-2141
Effect of vacuum brazing and rotary friction welding on microstructure and mechanical properties of laminated steel and nickel alloy joints
In this study, a joint between a vacuum brazed laminated bimetal material, consisting of steel and Inconel $$\circledR $$ alloy, and a solid material is investigated. This type of joint is applied in an Axially Laminated Anisotropic Synchronous Reluctance Machine (ALASynRM) rotor, where the laminated active section of the rotor is joined to solid supporting shafts either by rotary friction welding (RFW) or vacuum brazing. The test specimens were manufactured with different RFW parameters and parent material compositions to evaluate the joint behavior. The RFW friction pressure (104–155 MPa) and time (1.0 $$-$$ 3.0 s) were varied to assess their impact on joint performance and composition, while other process parameters remained constant. The joint’s alloy composition and microstructure were analyzed, and its mechanical performance was assessed using tensile tests. Additionally, molecular dynamics (MD) simulations were employed to understand the nanoscale phenomena that occur during RFW joint formation. In this study, the ultimate tensile strength (UTS) of the joint in all RFW samples surpassed that of the vacuum brazed laminated material, while the vacuum brazed joints did not achieve comparable UTS. Metallurgical analysis indicated good and consistent diffusion between laminated bimetal and solid materials, resulting in defect-free joints. The MD simulations were strongly correlated with the experimental results, further validating our findings.- 29 March 2025
- Published by Springer Nature in Welding in the World
- Vol. 69 (7) , 2123-2141
Open AccessEffect of vacuum brazing and rotary friction welding on microstructure and mechanical properties of laminated steel and nickel alloy joints
In this study, a joint between a vacuum brazed laminated bimetal material, consisting of steel and Inconel $$\circledR $$ alloy, and a solid material is investigated. This type of joint is applied in an Axially Laminated Anisotropic Synchronous Reluctance Machine (ALASynRM) rotor, where the laminated active section of the rotor is joined to solid supporting shafts either by rotary friction welding (RFW) or vacuum brazing. The test specimens were manufactured with different RFW parameters and parent material compositions to evaluate the joint behavior. The RFW friction pressure (104–155 MPa) and time (1.0 $$-$$ 3.0 s) were varied to assess their impact on joint performance and composition, while other process parameters remained constant. The joint’s alloy composition and microstructure were analyzed, and its mechanical performance was assessed using tensile tests. Additionally, molecular dynamics (MD) simulations were employed to understand the nanoscale phenomena that occur during RFW joint formation. In this study, the ultimate tensile strength (UTS) of the joint in all RFW samples surpassed that of the vacuum brazed laminated material, while the vacuum brazed joints did not achieve comparable UTS. Metallurgical analysis indicated good and consistent diffusion between laminated bimetal and solid materials, resulting in defect-free joints. The MD simulations were strongly correlated with the experimental results, further validating our findings. - Open Access
- 27 May 2024
- Published by AIP Publishing in Applied Physics Letters
- Vol. 124 (22)
Extracting the electronic structure of light elements in bulk materials through a Compton scattering method in the readily accessible hard x-ray regime
Our Compton profile measurements of Ti and TiH2 using readily available hard X-ray radiation at 27.5 keV, detected by both a Hitachi Vortex silicon-drift detector and a high-resolution superconducting transition-edge sensor array, are found to be in excellent accord with state-of-the-art density functional theory based calculations. The spherically averaged difference between the Compton profiles of TiH2 and Ti is well described by an inverted parabola, supporting an itinerant behavior of the electron gas screening the protons in the Ti matrix. Our experimental approach, validated by two different detectors, extends the applicability of Compton scattering technique to the readily accessible hard x-ray regime (below 30 keV). Our study suggests possibilities for experiments at low-flux bending magnet synchrotron beamlines and paves the way for the development of tabletop Compton experiments with x-ray tubes.
- 27 May 2024
- Published by AIP Publishing in Applied Physics Letters
- Vol. 124 (22)
Open AccessExtracting the electronic structure of light elements in bulk materials through a Compton scattering method in the readily accessible hard x-ray regime
Our Compton profile measurements of Ti and TiH2 using readily available hard X-ray radiation at 27.5 keV, detected by both a Hitachi Vortex silicon-drift detector and a high-resolution superconducting transition-edge sensor array, are found to be in excellent accord with state-of-the-art density functional theory based calculations. The spherically averaged difference between the Compton profiles of TiH2 and Ti is well described by an inverted parabola, supporting an itinerant behavior of the electron gas screening the protons in the Ti matrix. Our experimental approach, validated by two different detectors, extends the applicability of Compton scattering technique to the readily accessible hard x-ray regime (below 30 keV). Our study suggests possibilities for experiments at low-flux bending magnet synchrotron beamlines and paves the way for the development of tabletop Compton experiments with x-ray tubes.
- Open Access
- 28 August 2023
- Published by Elsevier in Computational Materials Science
- Vol. 230
Nanoscale phenomena during wetting of copper on nickel-based superalloy: A molecular dynamics study
- 28 August 2023
- Published by Elsevier in Computational Materials Science
- Vol. 230
Open AccessNanoscale phenomena during wetting of copper on nickel-based superalloy: A molecular dynamics study
- Open Access
- 18 July 2023
- Published by Taylor & Francis in Phase Transitions
- Vol. 96 (8) , 596-606
Study of ageing and size effects in Nickel–Titanium shape memory alloy using molecular dynamics simulations
- 18 July 2023
- Published by Taylor & Francis in Phase Transitions
- Vol. 96 (8) , 596-606
Open AccessStudy of ageing and size effects in Nickel–Titanium shape memory alloy using molecular dynamics simulations
- Open Access
Microstructure and Mechanical Properties of Steel and Ni-Based Superalloy Joints for Rotors of High-Speed Electric Motors
High-speed electric motors, e.g., axially laminated anisotropic synchronous reluctance motors (ALA-SynRM), use a solid rotor manufactured by joining alternating layers of magnetic and non-magnetic metallic sheets. The strength of the dissimilar metallic joints is critical for the rotor’s ability to withstand the operating conditions of the high-speed electrical machine. In this work, various dissimilar metallic joint configurations that can be used in high-speed ALA-SynRM rotors are studied by analyzing the shear strength, microstructure, hardness, and composition of the joints. Metallic joints of structural steels and Inconel® alloys fabricated by vacuum brazing and hot isostatic pressing (HIP) are studied. Finite element analysis (FEA) was performed to calculate the maximum shear stress of the joints that were subjected to various high speed operating conditions. The shear strength of the test specimens was measured and compared with FEA results. The microstructure and chemical composition of the joints were studied by using optical microscopy, scanning electron microscopy (SEM) and energy dispersive spectroscopy (EDS) on SEM. The results show that the hot isostatic pressed S1100MC-IN718 joint achieved the highest ultimate shear strength (233.3 MPa) followed by vacuum brazed S355MC-IN600 joint (230.1 MPa) and HIP S355-IN718 (203.5 MPa), thereby showing that vacuum brazing and HIP can be viable manufacturing methods to fabricate a high-speed ALA-SynRM rotor.
Open AccessMicrostructure and Mechanical Properties of Steel and Ni-Based Superalloy Joints for Rotors of High-Speed Electric Motors
High-speed electric motors, e.g., axially laminated anisotropic synchronous reluctance motors (ALA-SynRM), use a solid rotor manufactured by joining alternating layers of magnetic and non-magnetic metallic sheets. The strength of the dissimilar metallic joints is critical for the rotor’s ability to withstand the operating conditions of the high-speed electrical machine. In this work, various dissimilar metallic joint configurations that can be used in high-speed ALA-SynRM rotors are studied by analyzing the shear strength, microstructure, hardness, and composition of the joints. Metallic joints of structural steels and Inconel® alloys fabricated by vacuum brazing and hot isostatic pressing (HIP) are studied. Finite element analysis (FEA) was performed to calculate the maximum shear stress of the joints that were subjected to various high speed operating conditions. The shear strength of the test specimens was measured and compared with FEA results. The microstructure and chemical composition of the joints were studied by using optical microscopy, scanning electron microscopy (SEM) and energy dispersive spectroscopy (EDS) on SEM. The results show that the hot isostatic pressed S1100MC-IN718 joint achieved the highest ultimate shear strength (233.3 MPa) followed by vacuum brazed S355MC-IN600 joint (230.1 MPa) and HIP S355-IN718 (203.5 MPa), thereby showing that vacuum brazing and HIP can be viable manufacturing methods to fabricate a high-speed ALA-SynRM rotor.
- 13 April 2022
- Published by IOP Publishing in Modelling and Simulation in Materials Science and Engineering
- Vol. 30 (4) , 045008
Effect of hydrostatic pressure on the kinetics of alpha–omega phase transformation in zirconium
A three dimensional (3D) elastoplastic phase-field model, including strain hardening, is employed to study the effect of hydrostatic pressure in the range of 4–9 GPa on the kinetics of alpha–omega phase transformation in zirconium (Zr). The input data corresponding to pure Zr are acquired from experimental studies as well as by using the CALPHAD method. A decreasing incubation time, for the formation of omega variants, with increasing pressure is observed. Avrami (JMAK) equation is used to study the transformation kinetics by analysing the phase fraction plots predicted by the phase-field simulations. The estimated activation energy is in the range of 54–59 kJ mol −1 and decreases at an average rate of 992 J mol −1 per 1 GPa increase in pressure. The analysis of Avrami exponents, based on Cahn’s approach, show that the transformation region can be divided into two distinct regions with a change in slope, which is attributed to the site saturation. It is concluded that in the first region where the exponents are above 3, the transformation proceeds by nucleation and growth. In the second region where the exponents are sub-unity, the transformation proceeds by growth of the existing variants.
- 13 April 2022
- Published by IOP Publishing in Modelling and Simulation in Materials Science and Engineering
- Vol. 30 (4) , 045008
Effect of hydrostatic pressure on the kinetics of alpha–omega phase transformation in zirconium
A three dimensional (3D) elastoplastic phase-field model, including strain hardening, is employed to study the effect of hydrostatic pressure in the range of 4–9 GPa on the kinetics of alpha–omega phase transformation in zirconium (Zr). The input data corresponding to pure Zr are acquired from experimental studies as well as by using the CALPHAD method. A decreasing incubation time, for the formation of omega variants, with increasing pressure is observed. Avrami (JMAK) equation is used to study the transformation kinetics by analysing the phase fraction plots predicted by the phase-field simulations. The estimated activation energy is in the range of 54–59 kJ mol −1 and decreases at an average rate of 992 J mol −1 per 1 GPa increase in pressure. The analysis of Avrami exponents, based on Cahn’s approach, show that the transformation region can be divided into two distinct regions with a change in slope, which is attributed to the site saturation. It is concluded that in the first region where the exponents are above 3, the transformation proceeds by nucleation and growth. In the second region where the exponents are sub-unity, the transformation proceeds by growth of the existing variants.
- 4 March 2021
- Published by ASME International in Journal of Engineering Materials and Technology
- Vol. 143 (3) , 1-29
Modeling of Reversed Austenite Formation and Its Effect on Performance of Stainless Steel Components
The kinetics of reversed austenite formation in 301 stainless steel and its effect on the deformation of an automobile front bumper beam are studied by using modeling approaches at different length scales. The diffusion-controlled reversed austenite formation is studied by using the Johnson–Mehl–Avrami–Kolmogorov (JMAK) model, based on the experimental data. The model can be used to predict the volume fraction of reversed austenite in a temperature range of 650–750 °C. A three-dimensional elastoplastic phase-field model is used to study the diffusionless shear-type reversed austenite formation in 301 steel at 760 °C. The phase-field simulations show that reversion initiates at martensite lath boundaries and proceeds inwards of laths due to the high driving force at such high temperature. The effect of reversed austenite (RA) and martensite on the deformation of a bumper beam subjected to front and side impacts is studied by using finite element (FE) analysis. The FE simulations show that the presence of reversed austenite and martensite increased the critical speed at which the beam yielded and failed. RA fraction also affects the performance of the bumper beam.
- 4 March 2021
- Published by ASME International in Journal of Engineering Materials and Technology
- Vol. 143 (3) , 1-29
Modeling of Reversed Austenite Formation and Its Effect on Performance of Stainless Steel Components
The kinetics of reversed austenite formation in 301 stainless steel and its effect on the deformation of an automobile front bumper beam are studied by using modeling approaches at different length scales. The diffusion-controlled reversed austenite formation is studied by using the Johnson–Mehl–Avrami–Kolmogorov (JMAK) model, based on the experimental data. The model can be used to predict the volume fraction of reversed austenite in a temperature range of 650–750 °C. A three-dimensional elastoplastic phase-field model is used to study the diffusionless shear-type reversed austenite formation in 301 steel at 760 °C. The phase-field simulations show that reversion initiates at martensite lath boundaries and proceeds inwards of laths due to the high driving force at such high temperature. The effect of reversed austenite (RA) and martensite on the deformation of a bumper beam subjected to front and side impacts is studied by using finite element (FE) analysis. The FE simulations show that the presence of reversed austenite and martensite increased the critical speed at which the beam yielded and failed. RA fraction also affects the performance of the bumper beam.
- 1 July 2020
- Published by Elsevier in Journal of Materials Science & Technology
- Vol. 49, 157-165
Multi-length scale modeling of carburization, martensitic microstructure evolution and fatigue properties of steel gears
- 1 July 2020
- Published by Elsevier in Journal of Materials Science & Technology
- Vol. 49, 157-165
Multi-length scale modeling of carburization, martensitic microstructure evolution and fatigue properties of steel gears
- 1 May 2019
- Published by Elsevier in Computational Materials Science
- Vol. 162, 1-11
Effect of carbon on elastic properties and microstructure of maraging steel: First-principles and phase-field study
- 1 May 2019
- Published by Elsevier in Computational Materials Science
- Vol. 162, 1-11
Effect of carbon on elastic properties and microstructure of maraging steel: First-principles and phase-field study