Subhadip Mallick
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Subhadip Mallick has a total of 55 co-authors. Here are the top co-authors by number of shared publications:
- Jason R. Croy
Argonne National Laboratory
9 shared publications - Anh D. Vu
Argonne National Laboratory
3 shared publications - Daniel P. Abraham
Chemical Sciences and Engineering Division, Argonne National Laboratory, 9700 South Cass Avenue, Lemont, Illinois 60439, United States
3 shared publications - Eungje Lee
Argonne National Laboratory
3 shared publications - Jiajun Chen
Argonne National Laboratory
3 shared publications - Jihyeon Gim
Chemical Sciences and Engineering Division, Argonne National Laboratory, Lemont, IL 60439, USA
3 shared publications
Latest Publications
- Open Access
- 20 October 2026
- Published by Royal Society of Chemistry (RSC) in Energy & Environmental Science
- Vol. 19 (20) , 7099-7112
The effect of negative electrodes and cyclable lithium on the bulk redox mechanisms of lithium- and manganese-rich positive electrodes
In Li- and Mn-rich (LMR) full-cells, voltage fade (VF) and bulk manganese reduction are decoupled. Therefore, enhancing practical LMR performance should prioritize stabilizing lithium inventory rather than suppressing presumed Mn-centered redox.
- 20 October 2026
- Published by Royal Society of Chemistry (RSC) in Energy & Environmental Science
- Vol. 19 (20) , 7099-7112
Open AccessThe effect of negative electrodes and cyclable lithium on the bulk redox mechanisms of lithium- and manganese-rich positive electrodes
In Li- and Mn-rich (LMR) full-cells, voltage fade (VF) and bulk manganese reduction are decoupled. Therefore, enhancing practical LMR performance should prioritize stabilizing lithium inventory rather than suppressing presumed Mn-centered redox.
- Open Access
- 2 September 2026
- Published by The Electrochemical Society in Journal of the Electrochemical Society
- Vol. 173 (17) , 170508
The Impact of Cobalt Substitution in Lithiated Spinel/Layered Li 2 (MnNi) 1− δ/2 Co δ O 4 (0 ⩽ δ ⩽ 0.667) Cathodes for Li-Ion Batteries
In 2020, the discovery of the lithiated spinel Li 2 MnNiO 4 opened the door to the design of a new class of cathode materials for the lithium-ion battery industry. This compound is typically prepared in air at 400 °C and co-exists with a disordered layered structure of the same composition (LiMn 0.5 Ni 0.5 O 2 ), delivering most of its capacity (∼200 mAh g −1 ) between 4.8 and 3.0 V with essentially no redox on the manganese ions. This communication reports the effects of cobalt substitution on the structural and electrochemical properties of lithiated-spinel/layered Li 2 (MnNi) 1− δ/2 Co δ O 4 composite electrodes over the compositional range 0 ⩽ δ ⩽ 0.667.
- 2 September 2026
- Published by The Electrochemical Society in Journal of the Electrochemical Society
- Vol. 173 (17) , 170508
Open AccessThe Impact of Cobalt Substitution in Lithiated Spinel/Layered Li 2 (MnNi) 1− δ/2 Co δ O 4 (0 ⩽ δ ⩽ 0.667) Cathodes for Li-Ion Batteries
In 2020, the discovery of the lithiated spinel Li 2 MnNiO 4 opened the door to the design of a new class of cathode materials for the lithium-ion battery industry. This compound is typically prepared in air at 400 °C and co-exists with a disordered layered structure of the same composition (LiMn 0.5 Ni 0.5 O 2 ), delivering most of its capacity (∼200 mAh g −1 ) between 4.8 and 3.0 V with essentially no redox on the manganese ions. This communication reports the effects of cobalt substitution on the structural and electrochemical properties of lithiated-spinel/layered Li 2 (MnNi) 1− δ/2 Co δ O 4 composite electrodes over the compositional range 0 ⩽ δ ⩽ 0.667.
- Open Access
- 1 September 2026
- Published by Royal Society of Chemistry (RSC) in Journal of Materials Chemistry A
- Vol. 14 (52) , 35650-35663
Novel architectures for stabilization of Mn-rich cathodes: a high-valent approach to interfaces
Lithium-rich surface and grain-boundary structures, induced by Sb 5+ , mitigate Mn dissolution and help to stabilize LMR cathode interfaces.
- 1 September 2026
- Published by Royal Society of Chemistry (RSC) in Journal of Materials Chemistry A
- Vol. 14 (52) , 35650-35663
Open AccessNovel architectures for stabilization of Mn-rich cathodes: a high-valent approach to interfaces
Lithium-rich surface and grain-boundary structures, induced by Sb 5+ , mitigate Mn dissolution and help to stabilize LMR cathode interfaces.
- 3 June 2026
- Published by American Chemical Society (ACS) in Chemistry of Materials
- Vol. 38 (12) , 6077-6089
Unexpected Structural Complexity in Pseudo-Ruddlesden–Popper Phases
- 3 June 2026
- Published by American Chemical Society (ACS) in Chemistry of Materials
- Vol. 38 (12) , 6077-6089
Unexpected Structural Complexity in Pseudo-Ruddlesden–Popper Phases
- Open Access
- 23 April 2026
- Published by The Electrochemical Society in Journal of the Electrochemical Society
- Vol. 173 (9)
Cobalt-Free Lithium and Manganese Rich Cathodes for Electric Vehicle Applications:Influence of Inherent Properties on Temperature-Dependent Performance
Lithium- and manganese-rich (LMR) oxides are attractive options as next-generation, earth-abundant cathodes. Despite inherent properties that result in less-than-ideal performance, advancements in this class of cathodes toward commercialization have been steady. Herein, we report a benchmark study on the influence these inherent properties exert on the discharge rate of Co-free, LMR//graphite (Gr) cells as a function of temperature. Because low-temperature performance is an essential consideration in the design of electric vehicle cells, understanding the limitations of current LMR systems is essential in understanding their current applicability as well as strategies for improvement. This work identifies two major limitations in the rate performance of LMR//Gr cells and suggests several areas of focus where practical strategies may provide improvements.
- 23 April 2026
- Published by The Electrochemical Society in Journal of the Electrochemical Society
- Vol. 173 (9)
Open AccessCobalt-Free Lithium and Manganese Rich Cathodes for Electric Vehicle Applications:Influence of Inherent Properties on Temperature-Dependent Performance
Lithium- and manganese-rich (LMR) oxides are attractive options as next-generation, earth-abundant cathodes. Despite inherent properties that result in less-than-ideal performance, advancements in this class of cathodes toward commercialization have been steady. Herein, we report a benchmark study on the influence these inherent properties exert on the discharge rate of Co-free, LMR//graphite (Gr) cells as a function of temperature. Because low-temperature performance is an essential consideration in the design of electric vehicle cells, understanding the limitations of current LMR systems is essential in understanding their current applicability as well as strategies for improvement. This work identifies two major limitations in the rate performance of LMR//Gr cells and suggests several areas of focus where practical strategies may provide improvements.
- Open Access
- 2 February 2026
- Published by The Electrochemical Society in Journal of the Electrochemical Society
- Vol. 173 (3) , 030505
Defining Electrode-Level Metrics for Enabling Earth-Abundant, Mn-Rich Cathodes: A Technoeconomic Analysis of Experimental Materials
Manganese-rich oxides are attractive options as next-generation, earth-abundant cathodes and significant efforts are being directed toward commercial implementation. We report here an updated techno-economic analysis of the lithium- and manganese-rich (LMR) class of earth-abundant cathodes for electric vehicle applications. BatPaC modeling was used to define the cell-level metrics that must be met for these materials to be cost and energy competitive with the current commercial earth-abundant benchmark, LiFePO 4 , as well as anticipated variations such as LiMn 0.8 Fe 0.2 PO 4 . The model was used to evaluate a high-performance material from the literature and subsequently define R&D targets as the likely limits of practical performance for similar LMR systems. Experimental validation and BatPaC evaluation of an advanced, cobalt-free LMR cell system was also conducted. Results show that the advanced LMR cells come within ∼5% of the defined limits and exceed the energy of LiFe(Mn)PO 4 cells at a similar cost. Excellent cycle-life, low impedance, and low impedance rise were also achieved under the conditions tested and reveal that cobalt is not necessary to achieve high-performance LMR oxides. Although the analysis conducted herein reports on LMR cell systems, the methodology and target values defined for performance metrics easily extend to the evaluation of other systems under consideration as earth-abundant options.
- 2 February 2026
- Published by The Electrochemical Society in Journal of the Electrochemical Society
- Vol. 173 (3) , 030505
Open AccessDefining Electrode-Level Metrics for Enabling Earth-Abundant, Mn-Rich Cathodes: A Technoeconomic Analysis of Experimental Materials
Manganese-rich oxides are attractive options as next-generation, earth-abundant cathodes and significant efforts are being directed toward commercial implementation. We report here an updated techno-economic analysis of the lithium- and manganese-rich (LMR) class of earth-abundant cathodes for electric vehicle applications. BatPaC modeling was used to define the cell-level metrics that must be met for these materials to be cost and energy competitive with the current commercial earth-abundant benchmark, LiFePO 4 , as well as anticipated variations such as LiMn 0.8 Fe 0.2 PO 4 . The model was used to evaluate a high-performance material from the literature and subsequently define R&D targets as the likely limits of practical performance for similar LMR systems. Experimental validation and BatPaC evaluation of an advanced, cobalt-free LMR cell system was also conducted. Results show that the advanced LMR cells come within ∼5% of the defined limits and exceed the energy of LiFe(Mn)PO 4 cells at a similar cost. Excellent cycle-life, low impedance, and low impedance rise were also achieved under the conditions tested and reveal that cobalt is not necessary to achieve high-performance LMR oxides. Although the analysis conducted herein reports on LMR cell systems, the methodology and target values defined for performance metrics easily extend to the evaluation of other systems under consideration as earth-abundant options.
- Open Access
- 1 November 2025
- Published by The Electrochemical Society in Journal of the Electrochemical Society
- Vol. 172 (11) , 110513
The Sensitivity of Nickel Substitution in the Structural Design of Manganese-Based Layered and Lithiated Spinel Electrodes for Li-Ion Batteries
A concerted effort is being made at Argonne National Laboratory to explore and develop high-performance lithium-manganese-nickel-oxide cathode materials for the lithium battery industry. They are both energy- and cost-competitive relative to cobalt- and nickel-rich systems, such as LiCoO 2 , LiNi 0.8 Co 0.15 Al 0.05 O 2 , and LiNi 0.8 Mn 0.1 Co 0.1 O 2 . The recent discovery of the structural versatility of LiNi 0.5 Mn 0.5 O 2 , has revealed that it can exist in three configurations: lithiated spinel, partially disordered layered, and completely disordered rock salt within a common cubic-close-packed oxygen array. This versatility opens up the possibility of designing structurally integrated electrode components with interlinking 2-D (layered) and 3-D (spinel) channels for Li-ion transport. This paper highlights the sensitivity of Ni substitution and synthesis temperature on the structural and electrochemical properties of LiNi 0.50 Mn 0.50 O 2 , LiNi 0.53 Mn 0.47 O 2 , LiNi 0.47 Mn 0.53 O 2 , and LiNi 0.25 Mn 0.75 O 2 electrodes, as well as a cobalt-containing composition, LiNi 0.333 Mn 0.333 Co 0.333 O 2 , when synthesized at a relatively low temperature of 400 °C.
- 1 November 2025
- Published by The Electrochemical Society in Journal of the Electrochemical Society
- Vol. 172 (11) , 110513
Open AccessThe Sensitivity of Nickel Substitution in the Structural Design of Manganese-Based Layered and Lithiated Spinel Electrodes for Li-Ion Batteries
A concerted effort is being made at Argonne National Laboratory to explore and develop high-performance lithium-manganese-nickel-oxide cathode materials for the lithium battery industry. They are both energy- and cost-competitive relative to cobalt- and nickel-rich systems, such as LiCoO 2 , LiNi 0.8 Co 0.15 Al 0.05 O 2 , and LiNi 0.8 Mn 0.1 Co 0.1 O 2 . The recent discovery of the structural versatility of LiNi 0.5 Mn 0.5 O 2 , has revealed that it can exist in three configurations: lithiated spinel, partially disordered layered, and completely disordered rock salt within a common cubic-close-packed oxygen array. This versatility opens up the possibility of designing structurally integrated electrode components with interlinking 2-D (layered) and 3-D (spinel) channels for Li-ion transport. This paper highlights the sensitivity of Ni substitution and synthesis temperature on the structural and electrochemical properties of LiNi 0.50 Mn 0.50 O 2 , LiNi 0.53 Mn 0.47 O 2 , LiNi 0.47 Mn 0.53 O 2 , and LiNi 0.25 Mn 0.75 O 2 electrodes, as well as a cobalt-containing composition, LiNi 0.333 Mn 0.333 Co 0.333 O 2 , when synthesized at a relatively low temperature of 400 °C.
- 18 August 2025
- Published by American Chemical Society (ACS) in Chemistry of Materials
- Vol. 37 (17) , 6500-6511
Advancing the Performance of Lithium-Rich Oxides in Cooperation with Inherent Complexities: Engineering Domain Structure
- 18 August 2025
- Published by American Chemical Society (ACS) in Chemistry of Materials
- Vol. 37 (17) , 6500-6511
Advancing the Performance of Lithium-Rich Oxides in Cooperation with Inherent Complexities: Engineering Domain Structure
- Open Access
- 1 May 2025
- Published by The Electrochemical Society in Journal of the Electrochemical Society
- Vol. 172 (5) , 050527
Mitigating Transition Metal Dissolution from Mn-rich Cathodes: Influence of Processing and Testing Methods
Manganese-rich oxides continue to gain interest with respect to the development of Earth-abundant options for lithium-ion cathodes. Of the unique challenges that hinder the respective performance of various classes of such materials, manganese dissolution still stands as a common theme. The work herein explores Li3PO4 as a robust surface protection layer on a prototypical, Co-free, manganese-rich cathode in the way of a lithium- and manganese-rich oxide. The study highlights the critical importance of synthesis and processing in realizing optimal performance of a given surface treatment by comparing sol-gel and atomic layer deposition methods. Furthermore, cycling protocols are emphasized as a critical factor in adequately gauging the efficacy of surface protection strategies to mitigate manganese dissolution and the subsequent electrochemical consequence. Optimized Li3PO4 coatings coatings on lithium- and manganese-rich cathode particles are shown to greatly mitigate capacity fade, impedance rise, pore/void formation and mechanical damage during long-term cycling.
- 1 May 2025
- Published by The Electrochemical Society in Journal of the Electrochemical Society
- Vol. 172 (5) , 050527
Open AccessMitigating Transition Metal Dissolution from Mn-rich Cathodes: Influence of Processing and Testing Methods
Manganese-rich oxides continue to gain interest with respect to the development of Earth-abundant options for lithium-ion cathodes. Of the unique challenges that hinder the respective performance of various classes of such materials, manganese dissolution still stands as a common theme. The work herein explores Li3PO4 as a robust surface protection layer on a prototypical, Co-free, manganese-rich cathode in the way of a lithium- and manganese-rich oxide. The study highlights the critical importance of synthesis and processing in realizing optimal performance of a given surface treatment by comparing sol-gel and atomic layer deposition methods. Furthermore, cycling protocols are emphasized as a critical factor in adequately gauging the efficacy of surface protection strategies to mitigate manganese dissolution and the subsequent electrochemical consequence. Optimized Li3PO4 coatings coatings on lithium- and manganese-rich cathode particles are shown to greatly mitigate capacity fade, impedance rise, pore/void formation and mechanical damage during long-term cycling.
- Open Access
- 11 April 2025
- Published by The Electrochemical Society in Journal of the Electrochemical Society
- Vol. 172 (5) , 050503
Recent Developments in Lithium-Manganese-Nickel Oxide Electrochemistry: The Alchemy of LiMn0.5Ni0.5O2
Efforts have been underway for some time at Argonne National Laboratory to design structurally integrated and stabilized lithium-manganese-nickel-oxide cathode materials. The goal has been to find a cobalt-free, high-capacity cathode for a Li-ion battery that is competitive, both cost- and energy-wise, with lithium-nickel-manganese-cobalt-oxide (NMC) and lithium-iron-phosphate (LFP) products. This brief synopsis highlights the remarkable alchemy of LiMn0.5Ni0.5O2 resulting from its well-known, slightly disordered layered structure and the recently discovered lithiated spinel phase and totally disordered rock-salt configurations. All three arrangements share a structurally compatible cubic-close-packed oxygen array. The lithiated spinel and layered components provide an intersecting network of two- and three-dimensional channels that facilitate Li+-ion transport, while a minor amount of an extensively disordered rock-salt component likely serves to enhance the structural and electrochemical stability of the electrode. The synopsis also encompasses the historical development of lithiated spinel electrode materials and structurally integrated systems.
- 11 April 2025
- Published by The Electrochemical Society in Journal of the Electrochemical Society
- Vol. 172 (5) , 050503
Open AccessRecent Developments in Lithium-Manganese-Nickel Oxide Electrochemistry: The Alchemy of LiMn0.5Ni0.5O2
Efforts have been underway for some time at Argonne National Laboratory to design structurally integrated and stabilized lithium-manganese-nickel-oxide cathode materials. The goal has been to find a cobalt-free, high-capacity cathode for a Li-ion battery that is competitive, both cost- and energy-wise, with lithium-nickel-manganese-cobalt-oxide (NMC) and lithium-iron-phosphate (LFP) products. This brief synopsis highlights the remarkable alchemy of LiMn0.5Ni0.5O2 resulting from its well-known, slightly disordered layered structure and the recently discovered lithiated spinel phase and totally disordered rock-salt configurations. All three arrangements share a structurally compatible cubic-close-packed oxygen array. The lithiated spinel and layered components provide an intersecting network of two- and three-dimensional channels that facilitate Li+-ion transport, while a minor amount of an extensively disordered rock-salt component likely serves to enhance the structural and electrochemical stability of the electrode. The synopsis also encompasses the historical development of lithiated spinel electrode materials and structurally integrated systems.