JWJiantao Wang

Jiantao Wang

*This is an algorithmically generated author record based on publicly available information.

Jiantao Wang has a total of 9 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • A New Insight into Concrete Impermeability: Effect of Polymer Modification of Interfacial Transition Zone

    by Shuang Yang, Jiantao Wang, Wen Li, Yingxiang Wang, Yunpeng Liu

    Coarse aggregates were pretreated with asphalt emulsion to concentrate asphalt film in the interfacial transition zone (ITZ) so as to improve concrete impermeability at a relatively low polymer content. Several test methods, including artificial crack samples, model aggregate concrete, and surface element scanning, were employed to characterize the contribution of modified ITZ to concrete impermeability. The results showed that incorporating hydrophobic asphalt film in ITZ could simultaneously slow down water absorption while weakening the ITZ microstructure. The water absorption of concretes decreased with an increase in the asphalt content and asphalt-coated aggregates ratio. However, the rapid chloride migration tests showed different results, which could be attributed to the different water saturation states of concretes before the tests. The hydrophobic asphalt film could retard water absorption and, consequently, chloride ion diffusion, even in the presence of cracks.


  • Experimental and analytical investigation on seismic behavior of Q690 circular high‐strength concrete‐filled thin‐walled steel tubular columns

    by Jiantao Wang, Qing Sun, Xiaohong Wu, Yongcai Wu

    Summary: This paper proposed a new Q690 circular high‐strength concrete‐filled thin‐walled steel tubular (HCFTST) column comprising an ultrahigh‐strength steel tube (yield strength fy ≥ 690 MPa). A quasi‐static cyclic loading test was conducted to examine the seismic behavior, and the obtained lateral load‐displacement hysteresis curves, skeleton curves, and ductility were analyzed in detail. Then, a numerical model based on a nonlinear fiber beam‐column element incorporating the modified uniaxial cyclic constitutive laws for concrete and steel was developed mainly to predict the seismic behavior of the tested Q690 circular HCFTST columns. The effects of the concrete cylinder compressive strength (fc), steel yield strength (fy), axial compression ratio (n), and diameter‐to‐thickness (D/t) ratio on the seismic behavior were investigated through a parametric study. Finally, a simplified hysteretic model incorporating the moment‐resisting capacity and deterioration of the unloading stiffness in addition to a normalized skeleton curve and hysteretic criterion was established. The results indicate the following: the proposed Q690 circular HCFTST columns can display reasonable hysteretic behaviors to some extent; the use of high‐strength steel can lead to a significantly larger elasto‐plastic deformation capacity and delay the appearance of post‐peak behavior, even if a lower ductility capacity is provided; moderately loosening the limitations on the D/t ratio can also result in ideal hysteretic behaviors; and the established numerical model and simplified hysteretic model can satisfactorily predict the experimentally observed load‐displacement hysteretic curves, including the deterioration of the strength and stiffness and can, thus, offer design references for the elasto‐plastic analysis of circular HCFTST columns.


  • Cyclic testing of Q690 circular high-strength concrete-filled thin-walled steel tubular columns

    by Jiantao Wang, Qing Sun

    Under seismic action, the severe damage in critical regions of structures could be ascribed to the cumulative damage caused by cyclic loading. This article describes an investigation of the hysteresis behaviour of Q690 circular high-strength concrete-filled thin-walled steel tubular columns with out-of-code diameter-to-thickness ratios. A total of eight specimens were tested under constant axial compression and cyclic lateral loading. The study results of phase I testing consisting of a benchmark test were summarized to examine the seismic behaviour under standard loading, and those of the phase II testing that considered different fatigue loading modes and different concrete strengths were summarized to investigate the low-cycle fatigue behaviour. The load–displacement hysteretic curves, energy dissipation, strength and stiffness degradation were discussed in detail. A simplified method was proposed to predict the low-cycle fatigue life, which can be applied in the damage-based seismic design of circular concrete-filled steel tubular structures.


  • Open Access

    Performance Evaluation of Q690 High-Strength Concrete-Filled Thin-Walled Steel Tubular Columns under Compression-Bending Coupling

    by Jiantao Wang, Qing Sun

    The high-strength concrete-filled thin-walled steel tubular (HCFTST) columns, as a relatively new type structure member, could reduce the section size to obtain the favorable architecture aesthetic effects and gain further economic benefits. In this paper, the HCFTST columns were optimized on the basis of the orthogonal array of L16 (45) with three tested parameters. The orthogonal range analysis (ORA) was utilized to research the alteration degree, and the orthogonal variance analysis (OVA) was employed to analyze the significant degree between different parameters. Moreover, the optimized combinations based on performance index including strength, ductility, and energy dissipation were recommended to offer certain reference for structural design and application. Finally, a modified damage assessment model was proposed and verified. It indicates that the HCFTST columns with reasonable design could display favorable performance and can be expected to have a widespread application in engineering structures.

  • Open Access

    Experimental Study on High‐Cycle Fatigue Behavior of GFRP‐Steel Sleeve Composite Cross Arms

    by Jiantao Wang, Ning Tan, Shiming Zhou, Qing Sun

    To overcome the fatigue safety problem of transmission tower cross arms caused by the wind‐induced vibrations, an experimental study on the high‐cycle fatigue performance of a new type of GFRP‐steel sleeve composite cross arms was carried out. A total of six specimens were subjected to 500 thousand cyclic loadings based on the practical engineering background. The stress state was monitored, and a variety of load‐displacement‐time curves, the energy dissipation capacity, and the dynamic strain were analyzed to examine the effects of fatigue loading. After the fatigue test, the specimens without significant fatigue failure were evaluated to derive the residual bearing capacity. Based on the residual strength theory, the cumulative damage was examined, and the fatigue life was predicted under various loading conditions to ensure the reliability of composite cross arms. It is shown that the new type full‐scale GFRP‐steel sleeve composite cross arms can demonstrate a high level of safety redundancy on antifatigue performance and can be expected for wide application in power transmission towers.