Shangping Chen
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Shangping Chen has a total of 3 co-authors. Here are the top co-authors by number of shared publications:
Maxim Aarnts
Tata Steel, Ijmuiden, The Netherlands
3 shared publicationsRichard Mostert
Tata Steel, Ijmuiden, The Netherlands
3 shared publicationsHe Gao
Tata Steel, Ijmuiden, The Netherlands
1 shared publication
Latest Publications
- 19 December 2025
- Published by Springer Nature in Journal of Materials Engineering and Performance
- Vol. 35 (20) , 20228-20240
Spot Weldability of Transformation Induced Plasticity Steels with Varying Si and Al Content
- 19 December 2025
- Published by Springer Nature in Journal of Materials Engineering and Performance
- Vol. 35 (20) , 20228-20240
Spot Weldability of Transformation Induced Plasticity Steels with Varying Si and Al Content
- 1 December 2023
- Published by SAGE Publications in Materials Science and Technology
- Vol. 39 (17) , 2642-2661
Heat treatment effects on microstructure and properties of advanced high-strength steels
The effects of the austempering time on the microstructure and properties of two third-generation high-strength steels are investigated for austempering (TBF), and for quenching and partitioning (QP). The process parameters are chosen according to the capacity of an existing continuous annealing or galvanising line. More than 10% retained austenite can be stabilised although carbides start to form at short overageing times with the simulated cycles. The product of the tensile strength and total elongation for TBF is higher than for QP, and it peaks with increasing austempering time for TBF, but decreases monotonously for QP. The hole expansion capacity for QP is higher than for TBF and it peaks with austempering time for both TBF and QP.
- 1 December 2023
- Published by SAGE Publications in Materials Science and Technology
- Vol. 39 (17) , 2642-2661
Heat treatment effects on microstructure and properties of advanced high-strength steels
The effects of the austempering time on the microstructure and properties of two third-generation high-strength steels are investigated for austempering (TBF), and for quenching and partitioning (QP). The process parameters are chosen according to the capacity of an existing continuous annealing or galvanising line. More than 10% retained austenite can be stabilised although carbides start to form at short overageing times with the simulated cycles. The product of the tensile strength and total elongation for TBF is higher than for QP, and it peaks with increasing austempering time for TBF, but decreases monotonously for QP. The hole expansion capacity for QP is higher than for TBF and it peaks with austempering time for both TBF and QP.
- 2 October 2022
- Published by Taylor & Francis in Advances in Materials and Processing Technologies
- Vol. 9 (4) , 1848-1858
Cooling rate dependence of properties in a Si rich advanced high strength steel
The possibility to produce third-generation advanced high strength grades from a Fe-0.22C-2.1Mn-1.0Si steel through continuous cooling was explored. A large amount of retained austenite is formed at medium cooling rates ranging from 1°C/s to 15°C/s due to the fact that C enrichment in the austenite occurs because the high content of Si inhibits the formation of pearlite. A multi-phase microstructure including ferrite, bainite, martensite and retained austenite is obtained when the cooling rate is in between 5°C/s and 40°C/s. A grade of steel with an ultimate tensile strength of 1200 MPa, a total elongation of 8% and a hole expansion capacity of 20% can be obtained with a cooling rate of 15–20°C/s. Third generation high strength grades with enhanced formability cannot be obtained through continuous cooling process with the current composition as the size of the bainitic ferrite are too large and the stability of the retained austenite is too low.
- 2 October 2022
- Published by Taylor & Francis in Advances in Materials and Processing Technologies
- Vol. 9 (4) , 1848-1858
Cooling rate dependence of properties in a Si rich advanced high strength steel
The possibility to produce third-generation advanced high strength grades from a Fe-0.22C-2.1Mn-1.0Si steel through continuous cooling was explored. A large amount of retained austenite is formed at medium cooling rates ranging from 1°C/s to 15°C/s due to the fact that C enrichment in the austenite occurs because the high content of Si inhibits the formation of pearlite. A multi-phase microstructure including ferrite, bainite, martensite and retained austenite is obtained when the cooling rate is in between 5°C/s and 40°C/s. A grade of steel with an ultimate tensile strength of 1200 MPa, a total elongation of 8% and a hole expansion capacity of 20% can be obtained with a cooling rate of 15–20°C/s. Third generation high strength grades with enhanced formability cannot be obtained through continuous cooling process with the current composition as the size of the bainitic ferrite are too large and the stability of the retained austenite is too low.
- 1 April 2021
- Published by SAGE Publications in Materials Science and Technology
- Vol. 37 (6) , 651-662
Microstructure and properties of an advanced high-strength steel after austempering treatment
The microstructure and mechanical properties were investigated as a function of the austempering temperature in an Si-rich advanced high-strength steel that is expected to serve for automotive applications. The results indicate that both the size and the morphology of bainitic ferrite vary with the austempering temperature. Incomplete bainite transformation was observed only in a limited temperature range. The strength of the steel is dominated by the ferrite size of the matrix including bainitic ferrite and martensite. The hole expansion capacity exhibits a positive correlation to the C content of retained austenite and a negative correlation to the amount of the retained austenite and the formation of carbides.
- 1 April 2021
- Published by SAGE Publications in Materials Science and Technology
- Vol. 37 (6) , 651-662
Microstructure and properties of an advanced high-strength steel after austempering treatment
The microstructure and mechanical properties were investigated as a function of the austempering temperature in an Si-rich advanced high-strength steel that is expected to serve for automotive applications. The results indicate that both the size and the morphology of bainitic ferrite vary with the austempering temperature. Incomplete bainite transformation was observed only in a limited temperature range. The strength of the steel is dominated by the ferrite size of the matrix including bainitic ferrite and martensite. The hole expansion capacity exhibits a positive correlation to the C content of retained austenite and a negative correlation to the amount of the retained austenite and the formation of carbides.