Current Organizations / Institutes

The organizations/institutes from the scholar's latest article


Rahul Samyal has a total of 21 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Environmental assessment of pearl millet waste reinforced biocomposite ceiling tiles

    by Khalid Hussain Ansari, Srikanta Routroy, Amit Bhomia, Rahul Samyal

    Agricultural waste integration as secondary resource in the fabrication of sustainable building materials helps in reducing environmental impacts. Work presented here focuses on developing a biocomposite as an alternative to gypsum ceiling tiles by partially replacing gypsum with pearl millet waste. The waste incorporated in different proportions into the gypsum matrix. A comparative life cycle assessment of pearl millet waste and gypsum ceiling tiles assesses environmental impacts in midpoint and endpoint categories. In addition, leachate analysis examines potential leachate formation, while flexural strength test determines structural performance. Biocomposite tiles demonstrates reduced carbon dioxide emissions by 66.85% (1.80 kg CO2 eq) and lowered terrestrial ecotoxicity by 64.99% (4.93 kg 1,4-DCB eq) in the midpoint assessment. In addition, biocomposite tiles also show lower human health score of 88.36 mPt, indicating a 66.7% reduction in endpoint impact assessment. Furthermore, the leachate analysis shows 3869 mg/L of total dissolved solids and 2911 mg/L of total suspended solids. The flexural strength of biocomposite tile measured at 1.23 MPa aligns with the 1.21 MPa observed for gypsum ceiling tile, validating its comparable structural performance. Novelty of the work lies in exploring pearl millet waste as a sustainable building material, enhancing resource efficiency and reducing environmental burdens.

  • Pearl millet waste reinforced biocomposite ceiling tiles: a waste management approach

    by Khalid Hussain Ansari, Srikanta Routroy, Rahul Samyal, Anupam Singhal, Arun Kumar Jalan

    More efficient and standardised building materials led to the need for gypsum. However, despite its acceptance as a construction material, it has environmental drawbacks and limitations. The aim of this work was to develop biocomposite ceiling tiles as an alternative to gypsum ceiling tiles. To do this, different proportions (35–55%) of pearl millet seed coverings (PMSC) were used as a partial replacement for gypsum. Microstructural analysis was performed, followed by tests for flexural strength and thermal and acoustic insulation evaluations. Microstructural examination of the mix made with 35% PMSC, 30% gypsum powder, 15% lime and 20% waste paper showed a compact and homogeneous structure due to the effective binding and balanced integration of the elements. This mix achieved a flexural strength of 1.23 MPa, comparable to that of commonly used gypsum ceiling tiles (1.21 MPa). The same mix was found to have sound and thermal insulation performance comparable to those of conventional gypsum ceiling tiles across various frequencies and temperature ranges. This study is original in its approach and highlights the potential of PMSC in developing biocomposites as sustainable building materials, covering applications in ceiling tiles, partitions walls and decorative finishes across diverse geographic regions.


  • A novel route of carburizing through microwave hybrid heating

    by Rahul Samyal, Chitrank Khulbey, Raman Bedi, Dinesh Kumar Shukla, Ashok Kumar Bagha

    Carburizing is a surface treatment process by diffusing carbon into the steel. These days, manufacturing industries demand highly efficient processes that consume low power. Microwave processing is a newly evolving process that consumes low power. This study proposes a novel route for carburizing mild steel (substrate) through experimental and simulation studies using a microwave heating. Charcoal powder was used as a susceptor to convert microwave energy into heat energy and to deposit carbon on the surface of the specimen. The mild steel specimens were exposed to the microwave power input of 900 W and 360 W for exposure time of 1500 s and 1980 s naming it as S2 and S3 respectively. The microstructural analysis of specimens S2 and S3 confirms the formation of pearlite structures at the surface. However, the amount of pearlite structure was significantly higher for the S3. The higher carbon content is confirmed through energy-dispersive x-ray spectroscopy (EDS) analysis of specimen S3. The average hardness of the S3 specimen was determined to be 220.8 HV, which shows an increase of 38.36% compared to the S1 (base metal). x-ray diffraction (XRD) results indicate the additional cementite peaks (Fe3C) and ferrite-confirming phase transformations for carburized samples. The wear analysis of S2 and S3 was conducted through pin-on-disk testing. The peak COF of 0.73 and 0.64 was observed for S2 and S3 respectively. The hard surface of S3 resists the penetration of the counter body to a greater extent due to the fine morphology of pearlite. From the FEM study, the maximum value of 7.96 × 10 3 (V/m) was determined at the center region for the electric field distribution in the microwave cavity, which is the optimum value for efficient heating. The maximum temperature of the mild steel obtained during the carburization process was 900 °C in 1800 s. The microwave carburizing process requires relatively less time than the conventional carburizing process which will save energy consumption.


  • Joining of Metals Through Microwave Hybrid Heating

    by Rahul Samyal, Ankush Thakur, Raman Bedi, Ashok Kumar Bagha, Akhil Khajuria


  • Microstructural study of microwave welded austenitic stainless steel

    by Rahul Samyal, Raman Bedi, Ashok Kumar Bagha

    The joining of austenitic stainless steels through microwave hybrid heating has gained much attention due to its advantages, like uniform and volumetric heating. However, to establish a microwave joining process for promising applications, a microstructural study of the welded joint is still an area to explore. In the present study, microstructural analysis of austenitic stainless steel (SS304) joints is explained through optical microscopy, scanning electron microscopy (SEM), elemental mapping, X-ray diffraction (XRD) and Vickers' micro-hardness tester. Further, detailed microstructural analysis of interlayer and heat-affected zone (HAZ) is studied through electron back-scattered diffraction (EBSD). XRD results reveal the development of various Ni, Cr and the M23C6 type carbides at the joint interlayer region. SEM results point toward non-epitaxial grain evolution along the fusion zone. The mean microhardness of 350 ± 20 HV was determined at the joint interlayer region. A relatively fine grain structure was observed along the fusion boundary. However, moving away from the joint, two different forms of coarse grain heat-affected zone (CGHAZ) were observed. The presence of two different forms of CGHAZ is confirmed through inverse pole figure maps and grain size plots. The presence of high-angle boundaries (HABs) at 60° rotation describes the twin boundaries characterized along the axis. The existence of improved fractions of HABs in the microwave-joined specimen of SS will favor the microstructure to retard bulk deformation. The joint specimen endures a maximum force of 6.98 kN, and the ultimate tensile strength of 613 MPa with 4.75% of elongation. It is observed that microhardness observations and the microstructural studies in the research help establish a solid microstructure-property correlation for the joined material.


  • Investigation of mechanical properties of microwave welded SS304-SS202 lap joints

    by Rahul Samyal, Raman Bedi, Ashok Kumar Bagha

    The joint between dissimilar materials is always challenging to develop through traditional techniques due to the different properties of the parent materials. However, a novel non-traditional route of joining similar and dissimilar materials through energy conversion and absorption has been developed called SMHH (selective microwave hybrid heating). It has gained much attention due to its unique heating abilities. In the present work, the lap joint between SS202-SS304 is developed through SMHH placing nickel powder as an interlayer. The lap joint was characterized mechanically through shear tests and microhardness. Since the sheared area of the joint is large, it is challenging to achieve a good joint. Thus, to develop a solid joint, laser surface texturing (LST) was introduced to the joining surfaces, and the joints were characterized. After LST was introduced, a fully diffused joint interlayer region was observed through scanning electron microscopy (SEM). The EDS results confirmed the complete metallurgical bonding occurred by the diffusion of elements across the weld zone. From the XRD spectrum, the formation of intermetallic compounds like FeNi, FeNi3, C3Fe7, and M23C6 were identified at the joint region. The mean microhardness of 355 ± 10 HV was determined at the joint region of lap joints with LST. A lap joint with LST exhibits 217 MPa of shear strength, which is significantly higher than the joints without LST. Fractography of the shear failure specimens pointed out that partial heating of the interlayer caused incomplete bonding of the base metal and interlayer for without LST lap joints. However, mixed mode failure of SS202 near the overlap region of the LST lap joint occurred. It is concluded that the addition of LST on the lap joint has made a colossal impact on enhancing joint strength and intermetallic bonding. In addition, temperature-time profiling was studied to understand the heating mechanism involved in SMHH using thermocouples.


  • Comparative performance of various susceptor materials and vertical cavity shapes for selective microwave hybrid heating (SMHH)

    by Saurabh Rawat, Rahul Samyal, Raman Bedi, Ashok Kumar Bagha

    The microwave processing of materials is gaining popularity over the past decade due to its unique heating abilities. The microwave hybrid heating (MHH) technique has effectively processed bulk metallic materials. MHH is assisted by susceptor material which forces metals to absorb microwave radiations. Further, MHH is modified to selective microwave hybrid heating (SMHH) to increase the efficiency of the process. This work examines the performance of Graphite and Charcoal susceptors with a conical vertical cavity for SMHH using FEM simulation. It is observed that the maximum temperature achieved by Graphite was 215 °C at an exposure time of 300 s, whereas, for Charcoal susceptor, it is 655 °C. Further, the effect of different vertical cavity shapes (cylindrical and conical) on the SMHH technique is presented for Charcoal susceptor. For an exposure time of 300 s, the temperature rise in the conical and cylindrical cavity is 655 °C and 319 °C, respectively. From resistive heat flow, time-temperature profile and temperature distribution, it is clear how SMHH is significantly effective for a conical vertical cavity having Charcoal susceptor. In addition, the performance of the conical vertical cavity having Charcoal susceptor was validated through experimental study. The real-time temperature profile was determined through testo 885/testo 890 thermal imaging camera. The observed maximum temperature of the susceptor after heating for 300 s was 639.9 °C.


  • Finite element model updating of microwave welded lap joint with direct updating algorithm

    by Ashok Kumar Bagha, Shivashrit Tiwari, Shivani Kumari, Rahul Samyal, Raman Bedi, Nitin Sharma, Shashi Bahl

    Microwave joining is a non-conventional joining method that can be used to join bulk metals. Different types of joints such as butt-joint, lap joint, etc can be successfully joined with this novel green technique of joining. In this paper, a domestic microwave oven having a power output of 700W, frequency of 2.45 GHz, and capacity of 25L is used to weld the SS202-SS202 and SS304-SS304 bulk metals. To characterize the lap joints Vicker’s hardness test and SEM of the welded specimens are carried out. The experimental modal analysis is used to measure the experimental eigenvalues and eigenvectors of the welded lap joints. The finite element method has been used to develop the simulated finite element model of the microwave welded joints. The developed finite element model may be very beneficial to predict the dynamic characteristics of the welded structures. However, the finite element method is a numerical tool that gives approximate results. The finite element modeling of the structures depends upon various uncertain factors such as structural material properties, dimensions, boundary conditions, etc Due to these uncertainties in the simulated finite element model, there is always an error between the simulated and experimental observations. In this paper, a lap joint of bulk metals is fabricated by using microwave hybrid heating and a finite element model updating technique such as a direct updating algorithm is proposed to update its simulated finite element model. The objective is to update the simulated mass and the stiffness matrices of the microwave welded lap joint. The experimental modal analysis is used to measure the natural frequencies of the lap joint specimen experimentally. It is observed that the direct updating algorithm can successfully update the simulated finite element model of the welded joints and reduces the error between the simulated and experimental natural frequencies. It is found that the maximum error between the predicted and measured natural frequencies reduces to 0.56% by using the proposed algorithm for welded joints.


  • Open Access

    Predicting the effect of fiber orientations and boundary conditions on the optimal placement of PZT sensor on the composite structures

    by Rahul Samyal, Ashok Kumar Bagha, Raman Bedi, Shashi Bahl, Kuldeep K Saxena, Shankar Sehgal

    In this paper, the modal-model of the composite structure is predicted and viewed to decide the optimal position of the PZT sensors on the composite structures. The novelty of this work is to systematically study the effect of fiber orientations and boundary conditions on the modal-model and the optimal location of the PZT sensors on the composite structures. The glass fibers are reinforced in a polyester matrix at different fiber orientations such as 0°, 30°, 45°, 60° and 90°. It is used for various engineering applications, especially in the aerospace and automobile sector, and it is very important to measure its dynamical response. The PZT patches can be embedded on the composite structures to measure their vibrational response. In this paper, ABAQUS software is used to build the finite element model of the PZT-composite structure. The composite structure is modeled with different boundary conditions. It is observed that the orientation of the fibers as well as the boundary condition directly put their effect on the modal-model of the composite structure and also on the selection of the optimal position of the PZT patches. It is found that the optimal position of the PZT directly depends upon the fiber orientation.