Fernando Figueiredo
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Research Interests
Fernando Figueiredo has a total of 25 co-authors. Here are the top co-authors by number of shared publications:
- João Duarte
University of Coimbra IQGeo – Serviços, Ltd., Centre for Geosciences (CGeo), Department of Earth Sciences, University of Coimbra
4 shared publications Jose Carvalho
Geosciences Center, Department of Earth Sciences, University of Coimbra, Portugal
2 shared publications- Lídia Catarino
Geosciences Center, Department of Earth Sciences, University of Coimbra, 3030-790 Coimbra, Portugal
2 shared publications - Manuel J. Senos Matias
University of Aveiro
2 shared publications A. Pina
1 shared publicationC. Grangeia
1 shared publication
Latest Publications
- Open Access
- 21 May 2026
- Published by Springer Nature in Geoheritage
- Vol. 18 (2) , 126
Historic Quarries of Ançã Limestone, A Portuguese IUGS Heritage Stone
Ançã limestone is one of the most widely used building and carving stones in Portugal, particularly valued for sculpture due to its ease of carving. Although it has been exploited since prehistoric times, its greatest use was in the 14th century, when the quarries reached their greatest splendour. The Ançã limestone (“Pedra de Ançã” in Portuguese) belongs to a level of the Ançã Formation, which occurs in the municipality of Cantanhede, about 25 km northwest of Coimbra. This formation was deposited during the Bajocian and Bathonian (Middle Jurassic) periods in the Lusitanian Basin (central-western Portugal). It is about 250 m thick and consists at the base of layers reaching ≈ 2 to ≈ 3 m of greyish micritic limestone, slightly marly, changing laterally to light grey and yellowish to whitish. This is followed by creamy white micritic limestones in beds ≈ 0.5 to ≈ 1 m thick. This work aims to compile bibliographical information on the historic quarries of the Ançã limestone, which has been designated as an IUGS Global Heritage Stone by the International Union of Geological Sciences. This will allow the correct location of the historic quarries for their enhancement and as a source of raw material for possible future restorations.
- 21 May 2026
- Published by Springer Nature in Geoheritage
- Vol. 18 (2) , 126
Open AccessHistoric Quarries of Ançã Limestone, A Portuguese IUGS Heritage Stone
Ançã limestone is one of the most widely used building and carving stones in Portugal, particularly valued for sculpture due to its ease of carving. Although it has been exploited since prehistoric times, its greatest use was in the 14th century, when the quarries reached their greatest splendour. The Ançã limestone (“Pedra de Ançã” in Portuguese) belongs to a level of the Ançã Formation, which occurs in the municipality of Cantanhede, about 25 km northwest of Coimbra. This formation was deposited during the Bajocian and Bathonian (Middle Jurassic) periods in the Lusitanian Basin (central-western Portugal). It is about 250 m thick and consists at the base of layers reaching ≈ 2 to ≈ 3 m of greyish micritic limestone, slightly marly, changing laterally to light grey and yellowish to whitish. This is followed by creamy white micritic limestones in beds ≈ 0.5 to ≈ 1 m thick. This work aims to compile bibliographical information on the historic quarries of the Ançã limestone, which has been designated as an IUGS Global Heritage Stone by the International Union of Geological Sciences. This will allow the correct location of the historic quarries for their enhancement and as a source of raw material for possible future restorations.
- Open Access
Assessment of Groundwater Vulnerability in Dili City, Timor-Leste Using an Improved DRASTIC and Analytic Hierarchy Process (AHP) Method: Implications for Wastewater Management
Groundwater resources are critical in sustaining rapidly growing coastal urban regions like Dili City, Timor-Leste, where aquifers are prone to contamination. To inform groundwater pollution prevention and control in the Quaternary intergranular aquifer, a GIS-based groundwater vulnerability assessment was carried out using DRASTIC, modified DRASTIC, and modified DRASTIC–AHP methodologies. It confirmed that the central to northern urban area was the most vulnerable, while the southern part was the least vulnerable to contamination. Model performance was validated by correlating vulnerability indices with measured groundwater quality parameters, showing that the modified DRASTIC–AHP was the most accurate. The areas classified as having very low, low, moderate, high and very high vulnerability were 23.1%, 23.1%, 20.6%, 12.8%, and 19.2%, respectively, with high vulnerability along the northern coastline and Comoro River alluvial channel. Sensitivity analysis supports model robustness and identifies recharge, aquifer media, and hydraulic conductivity as the dominant controlling factors. The integrated modeling and sensitivity framework provides an efficient basis for prioritizing protection measures and infrastructure upgrades (e.g., sewerage) to reduce contamination risks. A key management implication is that centralized wastewater management is preferable to current practices for mitigating ongoing groundwater degradation.
Open AccessAssessment of Groundwater Vulnerability in Dili City, Timor-Leste Using an Improved DRASTIC and Analytic Hierarchy Process (AHP) Method: Implications for Wastewater Management
Groundwater resources are critical in sustaining rapidly growing coastal urban regions like Dili City, Timor-Leste, where aquifers are prone to contamination. To inform groundwater pollution prevention and control in the Quaternary intergranular aquifer, a GIS-based groundwater vulnerability assessment was carried out using DRASTIC, modified DRASTIC, and modified DRASTIC–AHP methodologies. It confirmed that the central to northern urban area was the most vulnerable, while the southern part was the least vulnerable to contamination. Model performance was validated by correlating vulnerability indices with measured groundwater quality parameters, showing that the modified DRASTIC–AHP was the most accurate. The areas classified as having very low, low, moderate, high and very high vulnerability were 23.1%, 23.1%, 20.6%, 12.8%, and 19.2%, respectively, with high vulnerability along the northern coastline and Comoro River alluvial channel. Sensitivity analysis supports model robustness and identifies recharge, aquifer media, and hydraulic conductivity as the dominant controlling factors. The integrated modeling and sensitivity framework provides an efficient basis for prioritizing protection measures and infrastructure upgrades (e.g., sewerage) to reduce contamination risks. A key management implication is that centralized wastewater management is preferable to current practices for mitigating ongoing groundwater degradation.
- 6 August 2025
- Published by Springer Nature
- p. 257-271
The Stone Heritage of the University of Coimbra (Portugal)
- 6 August 2025
- Published by Springer Nature
- p. 257-271
The Stone Heritage of the University of Coimbra (Portugal)
- Open Access
- 15 November 2019
- Published by IOP Publishing in IOP Conference Series: Earth and Environmental Science
- Vol. 362 (1) , 012101
Use of Ground Penetration Radar (GPR) in the Evaluation of Geological-Structural Elements of Ornamental Carbonated Rocks - Case Study in Valinho De Fatima, Portugal
In the extractive industry of carbonated ornamental rocks, the presence of discontinuities, size of grain, colour, textural anisotropy and porosity are factors that determine the extraction planning and their economic viability. This characterization is important for the planning and scaling of the exploitation. The objective of this work was in first, using the penetration radar in the soil (GPR), to identify and determine the spatial distribution of these elements. The choice of this non-destructive geophysical method to perform the work was because it is a fast method of inspection, having a good horizontal and vertical resolution, and relative precision. for this purpose, a PULSEEKKO GPR (SENSORS & SOFTWARE) acquisition equipment was used, with a system of two bi-static antennas (transmitter and receiver), unshielded, with a frequency of 100 MHz, using the reflection method with a common offset and with an antenna separation of 1,00 meter (m), at the pre-defined locations at each level of the quarry. The acquired data were subsequently processed in the REFLEXW® vers. Software. 7.5.9, from SANDMEIER-GEO®. The multiple profiles obtained (radargrams) [1], [2], which were compared with the corresponding exploitation fronts. This comparison allows validating the methodology used in the identification of existing structures, their vertical and horizontal limits and spatial relations between them.
- 15 November 2019
- Published by IOP Publishing in IOP Conference Series: Earth and Environmental Science
- Vol. 362 (1) , 012101
Open AccessUse of Ground Penetration Radar (GPR) in the Evaluation of Geological-Structural Elements of Ornamental Carbonated Rocks - Case Study in Valinho De Fatima, Portugal
In the extractive industry of carbonated ornamental rocks, the presence of discontinuities, size of grain, colour, textural anisotropy and porosity are factors that determine the extraction planning and their economic viability. This characterization is important for the planning and scaling of the exploitation. The objective of this work was in first, using the penetration radar in the soil (GPR), to identify and determine the spatial distribution of these elements. The choice of this non-destructive geophysical method to perform the work was because it is a fast method of inspection, having a good horizontal and vertical resolution, and relative precision. for this purpose, a PULSEEKKO GPR (SENSORS & SOFTWARE) acquisition equipment was used, with a system of two bi-static antennas (transmitter and receiver), unshielded, with a frequency of 100 MHz, using the reflection method with a common offset and with an antenna separation of 1,00 meter (m), at the pre-defined locations at each level of the quarry. The acquired data were subsequently processed in the REFLEXW® vers. Software. 7.5.9, from SANDMEIER-GEO®. The multiple profiles obtained (radargrams) [1], [2], which were compared with the corresponding exploitation fronts. This comparison allows validating the methodology used in the identification of existing structures, their vertical and horizontal limits and spatial relations between them.
- Open Access
- 1 August 2019
- Published by MDPI AG in Sustainability
- Vol. 11 (15) , 4158
The Use of Dolostone in Historical Buildings of Coimbra (Central Portugal)
In this paper, the importance of the dolostone (a carbonate sedimentary rock where the dominant carbonate mineral is dolomite) in monuments and urban buildings of the city of Coimbra, Portugal, is highlighted. Old quarries are not visible in the nucleus of the city, due to the sequential occupation by houses, and can only be identified by documentation (draws, contract letters and purchase orders). However, on the southern side of Mondego River (Santa Clara) some outcrops can be observed and were exploited until the mid-20th. It is presented a list of the old quarries and monuments made with this rock. The characterization of dolostones from the Coimbra Formation is also presented. It is made the connection between the local geology and the “identity” of Coimbra, putting in evidence the stone as a symbol that characterize the gilded aspect of the buildings. For restoration and rehabilitation works, a small number of blocks could be extracted from the Carvalhais quarry if were eventually necessary.
- 1 August 2019
- Published by MDPI AG in Sustainability
- Vol. 11 (15) , 4158
Open AccessThe Use of Dolostone in Historical Buildings of Coimbra (Central Portugal)
In this paper, the importance of the dolostone (a carbonate sedimentary rock where the dominant carbonate mineral is dolomite) in monuments and urban buildings of the city of Coimbra, Portugal, is highlighted. Old quarries are not visible in the nucleus of the city, due to the sequential occupation by houses, and can only be identified by documentation (draws, contract letters and purchase orders). However, on the southern side of Mondego River (Santa Clara) some outcrops can be observed and were exploited until the mid-20th. It is presented a list of the old quarries and monuments made with this rock. The characterization of dolostones from the Coimbra Formation is also presented. It is made the connection between the local geology and the “identity” of Coimbra, putting in evidence the stone as a symbol that characterize the gilded aspect of the buildings. For restoration and rehabilitation works, a small number of blocks could be extracted from the Carvalhais quarry if were eventually necessary.
- Open Access
- 1 March 2019
- Published by IOP Publishing in IOP Conference Series: Earth and Environmental Science
- Vol. 221 (1) , 012061
Use of Non-Destructive Methods in Structural Analysis of Petrous Materials - Ultrasonic Testing and Ground Penetrating Radar (GPR)
In the extractive and transformation processing industry of ornamental rocks, the presence of discontinuities, grain size, porosity and textural anisotropies in the explored blocks is an economic risk factor. This study aims the identification and possible quantification of these elements. The existence of a low-cost, non-intrusive and fast inspection method for the evaluation of blocks would facilitate their use avoiding their wastage. For this purpose, two nondestructive methods ("P" Wave Ultrasonic Testing and the Ground Penetration Radar (GPR)) were tested on a limestone rock block and compared the models obtained. The portable ultrasound equipment used was a Proceq Pundit Lab (Portable Ultrasonic Non-Destructive Digital Indicating Tester) which is based on the pulse rate method with 54 KHz to provide information about the uniformity, cavities, cracks and defects of the material concerned by the measurement of the ultrasonic wave time and the measurement of the pulse rate. The equipment used for the GPR data acquisition was a PULSEEKKO GPR (SENSORS & SOFTWARE), with a system of two bistatic antennas (transmitter and receiver) with a frequency of 1 GHz, using the reflection method with a common offset and with an antenna separation of 0,15 meters [m]. To make a comparison of the results valid and representative, both tests were performed with 0,10 m spacing between measurements, according to a pre-defined and common grid. In the case of the ultrasonic test, velocity color maps were created based on the results of the measurements, and through this colors differences it was possible to detect and locate some of the individual and visible fractures, but also not visible fractures on the surface of the tested face. By increasing the distance between transducers, the measurement depth also increases, creating maps of the same face at different depths. This method allows us to create several GPR profiles (radargrams) were obtained because of the processing, and were used to create 2, 2,5 and 3D models to identify the existing structures, their vertical and horizontal limits and spatial relationships between them.
- 1 March 2019
- Published by IOP Publishing in IOP Conference Series: Earth and Environmental Science
- Vol. 221 (1) , 012061
Open AccessUse of Non-Destructive Methods in Structural Analysis of Petrous Materials - Ultrasonic Testing and Ground Penetrating Radar (GPR)
In the extractive and transformation processing industry of ornamental rocks, the presence of discontinuities, grain size, porosity and textural anisotropies in the explored blocks is an economic risk factor. This study aims the identification and possible quantification of these elements. The existence of a low-cost, non-intrusive and fast inspection method for the evaluation of blocks would facilitate their use avoiding their wastage. For this purpose, two nondestructive methods ("P" Wave Ultrasonic Testing and the Ground Penetration Radar (GPR)) were tested on a limestone rock block and compared the models obtained. The portable ultrasound equipment used was a Proceq Pundit Lab (Portable Ultrasonic Non-Destructive Digital Indicating Tester) which is based on the pulse rate method with 54 KHz to provide information about the uniformity, cavities, cracks and defects of the material concerned by the measurement of the ultrasonic wave time and the measurement of the pulse rate. The equipment used for the GPR data acquisition was a PULSEEKKO GPR (SENSORS & SOFTWARE), with a system of two bistatic antennas (transmitter and receiver) with a frequency of 1 GHz, using the reflection method with a common offset and with an antenna separation of 0,15 meters [m]. To make a comparison of the results valid and representative, both tests were performed with 0,10 m spacing between measurements, according to a pre-defined and common grid. In the case of the ultrasonic test, velocity color maps were created based on the results of the measurements, and through this colors differences it was possible to detect and locate some of the individual and visible fractures, but also not visible fractures on the surface of the tested face. By increasing the distance between transducers, the measurement depth also increases, creating maps of the same face at different depths. This method allows us to create several GPR profiles (radargrams) were obtained because of the processing, and were used to create 2, 2,5 and 3D models to identify the existing structures, their vertical and horizontal limits and spatial relationships between them.
- 1 January 2018
- Published by EAGE Publications bv
- p. 1-5
Geophysics in the Prospecting Hydrogeological of Santiago
- 1 January 2018
- Published by EAGE Publications bv
- p. 1-5
Geophysics in the Prospecting Hydrogeological of Santiago
- 28 April 2011
- Published by Oxford University Press (OUP) in Journal of Geophysics and Engineering
- Vol. 8 (2) , 351-365
A multi-method high-resolution geophysical survey in the Machado de Castro museum, central Portugal
- 28 April 2011
- Published by Oxford University Press (OUP) in Journal of Geophysics and Engineering
- Vol. 8 (2) , 351-365
A multi-method high-resolution geophysical survey in the Machado de Castro museum, central Portugal
- 1 January 2008
- Published by EAGE Publications bv
High Resolution Geophysics Inside Machado de Castro Museum – Coimbra, Centre Portugal
- 1 January 2008
- Published by EAGE Publications bv
High Resolution Geophysics Inside Machado de Castro Museum – Coimbra, Centre Portugal