Connor J. O'DEa
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Connor J. O'DEa has a total of 37 co-authors. Here are the top co-authors by number of shared publications:
- Zachariah A. Page
The University of Texas at Austin
10 shared publications - Sean Thomas Roberts
The University of Texas at Austin
5 shared publications - Tod A. Grusenmeyer
Air Force Research Laboratory, Materials and Manufacturing Directorate, Wright-Patterson Air Force Base, Dayton, USA
3 shared publications - Adrian K. Rylski
Department of Chemistry The University of Texas at Austin 78712 Austin TX USA
2 shared publications - Ain Uddin
Department of Chemistry The University of Texas at Austin 78712 Austin TX USA
2 shared publications - Jack T. Ly
Materials and Manufacturing Directorate Air Force Research Laboratory 45433 Wright-Patterson AFB OH USA
2 shared publications
Latest Publications
- Open Access
- 20 August 2026
- Published by Royal Society of Chemistry (RSC) in Journal of Materials Chemistry C
- Vol. 14 (32) , 14402-14412
Morphology matters: microscopic control of the Fermi level in TIPS-pyrene
Correlated optical and scanning probe microscopy reveal how morphology and polymorphism govern electronic structure in TIPS-pyrene, establishing Fermi level engineering as a design strategy for solid-state materials.
- 20 August 2026
- Published by Royal Society of Chemistry (RSC) in Journal of Materials Chemistry C
- Vol. 14 (32) , 14402-14412
Open AccessMorphology matters: microscopic control of the Fermi level in TIPS-pyrene
Correlated optical and scanning probe microscopy reveal how morphology and polymorphism govern electronic structure in TIPS-pyrene, establishing Fermi level engineering as a design strategy for solid-state materials.
- Open Access
- 14 August 2026
- Published by American Association for the Advancement of Science (AAAS) in Science Advances
- Vol. 12 (33)
Single-exposure holographic 3D printing via inverse-designed phase masks
Additive manufacturing using light is commonly constrained by serial voxel-by-voxel or layer-by-layer processing, which fundamentally limits fabrication speed and scalability. Here, we introduce a single-exposure holographic three-dimensional (3D) printing approach that synthesizes an entire volumetric dose distribution optically in one step. The method combines inverse-designed microstructured phase masks with photopolymer resins engineered for controlled optical absorption. By precisely tailoring the phase-mask topography, we generate arbitrary 3D light-intensity distributions within the resin, including intentionally encoded dark regions that define hollow internal features. Simultaneously, the resin formulation is designed to balance optical penetration with sufficient local energy deposition to achieve high-fidelity polymerization throughout the volume. Using this approach, millimeter-scale architectures comprising more than 10 6 addressable voxels are fabricated in a single 7.5-second exposure, corresponding to a volumetric throughput of ∼1 cubic millimeters per second (>10 5 voxels per second). The demonstrated performance is presently limited by resin kinetics and illumination geometry rather than by the phase-mask framework itself. Because the volumetric information capacity scales with the space-bandwidth product of the phase mask, this approach provides a clear pathway toward substantially higher throughput, enabling scalable fabrication of micro-optical components, biomedical scaffolds, and other precision-engineered mesoscale systems.
- 14 August 2026
- Published by American Association for the Advancement of Science (AAAS) in Science Advances
- Vol. 12 (33)
Open AccessSingle-exposure holographic 3D printing via inverse-designed phase masks
Additive manufacturing using light is commonly constrained by serial voxel-by-voxel or layer-by-layer processing, which fundamentally limits fabrication speed and scalability. Here, we introduce a single-exposure holographic three-dimensional (3D) printing approach that synthesizes an entire volumetric dose distribution optically in one step. The method combines inverse-designed microstructured phase masks with photopolymer resins engineered for controlled optical absorption. By precisely tailoring the phase-mask topography, we generate arbitrary 3D light-intensity distributions within the resin, including intentionally encoded dark regions that define hollow internal features. Simultaneously, the resin formulation is designed to balance optical penetration with sufficient local energy deposition to achieve high-fidelity polymerization throughout the volume. Using this approach, millimeter-scale architectures comprising more than 10 6 addressable voxels are fabricated in a single 7.5-second exposure, corresponding to a volumetric throughput of ∼1 cubic millimeters per second (>10 5 voxels per second). The demonstrated performance is presently limited by resin kinetics and illumination geometry rather than by the phase-mask framework itself. Because the volumetric information capacity scales with the space-bandwidth product of the phase mask, this approach provides a clear pathway toward substantially higher throughput, enabling scalable fabrication of micro-optical components, biomedical scaffolds, and other precision-engineered mesoscale systems.
- Open Access
- 12 March 2026
- Published by Wiley in Advanced Functional Materials
- Vol. 36 (41)
Triplet‐Triplet Annihilation Enhances Photochemical Curing Contrast for Vat‐Based 3D Printing
Vat photopolymerization is a leading additive manufacturing strategy, yet its fidelity across length scales is fundamentally constrained by the sublinear dependence of curing rate on excitation intensity, which promotes overcure and loss of resolution. Here, we present a systematic, mechanism‐based comparison of Type I, Type II, and triple‐triplet annihilation photopolymerization (TTAP) within digital light processing (DLP) 3D printing. Using resins with matched optical densities, we show that TTAP uniquely exhibits a superlinear initiation response that suppresses overcure, yielding superior z ‐confinement and balanced x , y ‐fidelity compared to Type I and II photoinitiation. Under ambient conditions and low‐intensity green light (525 nm, 100 mW cm −2 ), TTAP resins achieve rapid curing (≈45 mm/h) while reliably fabricating features spanning tens of micrometers to millimeters, including complex geometries with overhangs, unsupported structures, and enclosed cavities. By enabling contrast‐enhanced curing at LED‐accessible intensities, this work establishes TTAP as a distinct and versatile photoinitiation paradigm and provides a framework for improving resolution and fidelity in visible‐light vat photopolymerization among other emerging additive manufacturing platforms.
- 12 March 2026
- Published by Wiley in Advanced Functional Materials
- Vol. 36 (41)
Open AccessTriplet‐Triplet Annihilation Enhances Photochemical Curing Contrast for Vat‐Based 3D Printing
Vat photopolymerization is a leading additive manufacturing strategy, yet its fidelity across length scales is fundamentally constrained by the sublinear dependence of curing rate on excitation intensity, which promotes overcure and loss of resolution. Here, we present a systematic, mechanism‐based comparison of Type I, Type II, and triple‐triplet annihilation photopolymerization (TTAP) within digital light processing (DLP) 3D printing. Using resins with matched optical densities, we show that TTAP uniquely exhibits a superlinear initiation response that suppresses overcure, yielding superior z ‐confinement and balanced x , y ‐fidelity compared to Type I and II photoinitiation. Under ambient conditions and low‐intensity green light (525 nm, 100 mW cm −2 ), TTAP resins achieve rapid curing (≈45 mm/h) while reliably fabricating features spanning tens of micrometers to millimeters, including complex geometries with overhangs, unsupported structures, and enclosed cavities. By enabling contrast‐enhanced curing at LED‐accessible intensities, this work establishes TTAP as a distinct and versatile photoinitiation paradigm and provides a framework for improving resolution and fidelity in visible‐light vat photopolymerization among other emerging additive manufacturing platforms.
- Open Access
- 11 November 2025
- Published by American Chemical Society (ACS) in ChemRxiv
Green-to-Violet Photon Upconversion Enables Simultaneous 3D Printing of Macro and Microscale Features with Vat Photopolymerization
Vat photopolymerization (VPP) is a leading additive manufacturing strategy, yet its fidelity across length scales is fundamentally constrained by the sublinear dependence of curing rate on excitation intensity, which promotes overcure and loss of resolution. Here, we present a systematic comparison of Type I, Type II, and Type III (triplet–triplet annihilation upconversion, TTA-UC) photopolymerization mechanisms within digital light processing (DLP) 3D printing. Using matched optical densities, we show that Type III uniquely exhibits a superlinear initiation response that suppresses overcure, yielding superior z-confinement and balanced x,y-fidelity compared to Type I and II. Under low-intensity green light (525 nm, 100 mW cm-2) and ambient conditions, Type III resins achieved rapid curing (~3.8 s/50 µm layer) and reliably fabricated features spanning tens of micrometers to millimeters, including complex geometries with overhangs, unsupported structures, and enclosed cavities. Beyond this proof-of-concept, the visible-light operating window offers opportunities for cytocompatible bioprinting, functional nanocomposites, and integration into volumetric printing platforms. These results establish Type III as a distinct and versatile photoinitiation paradigm, advancing the precision of visible-light additive manufacturing.
- 11 November 2025
- Published by American Chemical Society (ACS) in ChemRxiv
Open AccessGreen-to-Violet Photon Upconversion Enables Simultaneous 3D Printing of Macro and Microscale Features with Vat Photopolymerization
Vat photopolymerization (VPP) is a leading additive manufacturing strategy, yet its fidelity across length scales is fundamentally constrained by the sublinear dependence of curing rate on excitation intensity, which promotes overcure and loss of resolution. Here, we present a systematic comparison of Type I, Type II, and Type III (triplet–triplet annihilation upconversion, TTA-UC) photopolymerization mechanisms within digital light processing (DLP) 3D printing. Using matched optical densities, we show that Type III uniquely exhibits a superlinear initiation response that suppresses overcure, yielding superior z-confinement and balanced x,y-fidelity compared to Type I and II. Under low-intensity green light (525 nm, 100 mW cm-2) and ambient conditions, Type III resins achieved rapid curing (~3.8 s/50 µm layer) and reliably fabricated features spanning tens of micrometers to millimeters, including complex geometries with overhangs, unsupported structures, and enclosed cavities. Beyond this proof-of-concept, the visible-light operating window offers opportunities for cytocompatible bioprinting, functional nanocomposites, and integration into volumetric printing platforms. These results establish Type III as a distinct and versatile photoinitiation paradigm, advancing the precision of visible-light additive manufacturing.
- Open Access
- 13 October 2025
- Published by Wiley in Advanced Functional Materials
- Vol. 36 (18)
Energy‐Efficient Bulk Photoalignment of Main‐Chain Liquid Crystalline Polymers Enabled by In Situ Monitoring
Main‐chain liquid crystalline polymers (LCPs) offer tunable anisotropic properties essential for applications in optical data storage, soft robotics, and sensing. While photoalignment provides a powerful, non‐contact route to control mesogen orientation, its use has been largely constrained to sub‐micron films due to light attenuation and weak anchoring. Here, a strategy is reported for bulk photoalignment of azobenzene‐containing main‐chain LCPs, enabled by in situ optical monitoring and systematic structure–processing analysis. By tuning molecular weight, azobenzene content, cooling rate, and sample thickness, key parameters are revealed that govern alignment efficiency. Optically anisotropic films with order parameters ( S ) ≥0.25 and thicknesses up to 130 µm are achieved, surpassing conventional alignment limits. Azobenzene– r –C6M copolymers align rapidly and are stabilized through crystallization without chemical crosslinking. For example, 2 µm‐thick copolymer films reach S = 0.63 within 6 min using 420 nm light exposure (30 mW cm −2 ), while 200 nm homopolymers require 34 min to reach S = 0.48. Reversible QR code write–read–erase cycles highlight potential in rewritable optical media. This work introduces a scalable approach for reconfigurable alignment in LCPs and advances the design of bulk‐responsive anisotropic materials.
- 13 October 2025
- Published by Wiley in Advanced Functional Materials
- Vol. 36 (18)
Open AccessEnergy‐Efficient Bulk Photoalignment of Main‐Chain Liquid Crystalline Polymers Enabled by In Situ Monitoring
Main‐chain liquid crystalline polymers (LCPs) offer tunable anisotropic properties essential for applications in optical data storage, soft robotics, and sensing. While photoalignment provides a powerful, non‐contact route to control mesogen orientation, its use has been largely constrained to sub‐micron films due to light attenuation and weak anchoring. Here, a strategy is reported for bulk photoalignment of azobenzene‐containing main‐chain LCPs, enabled by in situ optical monitoring and systematic structure–processing analysis. By tuning molecular weight, azobenzene content, cooling rate, and sample thickness, key parameters are revealed that govern alignment efficiency. Optically anisotropic films with order parameters ( S ) ≥0.25 and thicknesses up to 130 µm are achieved, surpassing conventional alignment limits. Azobenzene– r –C6M copolymers align rapidly and are stabilized through crystallization without chemical crosslinking. For example, 2 µm‐thick copolymer films reach S = 0.63 within 6 min using 420 nm light exposure (30 mW cm −2 ), while 200 nm homopolymers require 34 min to reach S = 0.48. Reversible QR code write–read–erase cycles highlight potential in rewritable optical media. This work introduces a scalable approach for reconfigurable alignment in LCPs and advances the design of bulk‐responsive anisotropic materials.
- Open Access
- 12 August 2025
- Published by Royal Society of Chemistry (RSC) in Journal of Materials Chemistry A
- Vol. 13 (36) , 30151-30157
Design of phthalocyanine metal complexes for efficient far-red to near-IR light-initiated photopolymerizations
Efficient near-infrared (NIR) photopolymerization is promising for applications such as hydrogel bioprinting, composite manufacturing, and other technologies that benefit from deep light penetration and low-energy activation. Yet, design principles for optimizing NIR photoinitiators, particularly those based on earth-abundant or metal-free elements, remain limited. Here, a library of phthalocyanine (Pc) and naphthalocyanine (Nc) derivatives was synthesized, characterized, and evaluated as photoredox catalysts for NIR-induced radical polymerizations. Variations in metal center (Zn, Si, Pd), α-substitution (pentyl or butoxy), and π-extension (Pcvs.Nc) enabled tuning of light absorption, excited-state energies and lifetimes, and triplet excited state quantum yields. Polymerization kinetics were quantified using real-time FTIR spectroscopy under LED irradiation (740–940 nm), with photon absorption normalized to allow direct comparison of internal quantum yields. This work provides a framework for quantitative benchmarking of NIR photoinitiators under controlled conditions. Among the catalysts studied, a Pd–Pc complex showed the highest internal efficiency, while a Si–Nc catalyst outperformed a leading commercial cyanine initiator, highlighting the potential of silicon as a sustainable alternative to precious metals. These results establish clear structure–property relationships and offer guiding principles for the design of next-generation NIR photoinitiators suited for biomedical and advanced manufacturing technologies.
- 12 August 2025
- Published by Royal Society of Chemistry (RSC) in Journal of Materials Chemistry A
- Vol. 13 (36) , 30151-30157
Open AccessDesign of phthalocyanine metal complexes for efficient far-red to near-IR light-initiated photopolymerizations
Efficient near-infrared (NIR) photopolymerization is promising for applications such as hydrogel bioprinting, composite manufacturing, and other technologies that benefit from deep light penetration and low-energy activation. Yet, design principles for optimizing NIR photoinitiators, particularly those based on earth-abundant or metal-free elements, remain limited. Here, a library of phthalocyanine (Pc) and naphthalocyanine (Nc) derivatives was synthesized, characterized, and evaluated as photoredox catalysts for NIR-induced radical polymerizations. Variations in metal center (Zn, Si, Pd), α-substitution (pentyl or butoxy), and π-extension (Pcvs.Nc) enabled tuning of light absorption, excited-state energies and lifetimes, and triplet excited state quantum yields. Polymerization kinetics were quantified using real-time FTIR spectroscopy under LED irradiation (740–940 nm), with photon absorption normalized to allow direct comparison of internal quantum yields. This work provides a framework for quantitative benchmarking of NIR photoinitiators under controlled conditions. Among the catalysts studied, a Pd–Pc complex showed the highest internal efficiency, while a Si–Nc catalyst outperformed a leading commercial cyanine initiator, highlighting the potential of silicon as a sustainable alternative to precious metals. These results establish clear structure–property relationships and offer guiding principles for the design of next-generation NIR photoinitiators suited for biomedical and advanced manufacturing technologies.
- Open Access
- 16 January 2024
- Published by American Chemical Society (ACS) in ACS Central Science
- Vol. 10 (2) , 272-282
Triplet Upconversion under Ambient Conditions Enables Digital Light Processing 3D Printing
The rapid photochemical conversion of materials from liquid to solid (i.e., curing) has enabled the fabrication of modern plastics used in microelectronics, dentistry, and medicine. However, industrialized photocurables remain restricted to unimolecular bond homolysis reactions (Type I photoinitiations) that are driven by high-energy UV light. This narrow mechanistic scope both challenges the production of high-resolution objects and restricts the materials that can be produced using emergent manufacturing technologies (e.g., 3D printing). Herein we develop a photosystem based on triplet-triplet annihilation upconversion (TTA-UC) that efficiently drives a Type I photocuring process using green light at low power density (2) and in the presence of ambient oxygen. This system also exhibits a superlinear dependence of its cure depth on the light exposure intensity, which enhances spatial resolution. This enables for the first-time integration of TTA-UC in an inexpensive, rapid, and high-resolution manufacturing process, digital light processing (DLP) 3D printing. Moreover, relative to traditional Type I and Type II (photoredox) strategies, the present TTA-UC photoinitiation method results in improved cure depth confinement and resin shelf stability. This report provides a user-friendly avenue to utilize TTA-UC in ambient photochemical processes and paves the way toward fabrication of next-generation plastics with improved geometric precision and functionality.
- 16 January 2024
- Published by American Chemical Society (ACS) in ACS Central Science
- Vol. 10 (2) , 272-282
Open AccessTriplet Upconversion under Ambient Conditions Enables Digital Light Processing 3D Printing
The rapid photochemical conversion of materials from liquid to solid (i.e., curing) has enabled the fabrication of modern plastics used in microelectronics, dentistry, and medicine. However, industrialized photocurables remain restricted to unimolecular bond homolysis reactions (Type I photoinitiations) that are driven by high-energy UV light. This narrow mechanistic scope both challenges the production of high-resolution objects and restricts the materials that can be produced using emergent manufacturing technologies (e.g., 3D printing). Herein we develop a photosystem based on triplet-triplet annihilation upconversion (TTA-UC) that efficiently drives a Type I photocuring process using green light at low power density (2) and in the presence of ambient oxygen. This system also exhibits a superlinear dependence of its cure depth on the light exposure intensity, which enhances spatial resolution. This enables for the first-time integration of TTA-UC in an inexpensive, rapid, and high-resolution manufacturing process, digital light processing (DLP) 3D printing. Moreover, relative to traditional Type I and Type II (photoredox) strategies, the present TTA-UC photoinitiation method results in improved cure depth confinement and resin shelf stability. This report provides a user-friendly avenue to utilize TTA-UC in ambient photochemical processes and paves the way toward fabrication of next-generation plastics with improved geometric precision and functionality.
- Open Access
- 13 September 2023
- Published by Royal Society of Chemistry (RSC) in Journal of Materials Chemistry A
- Vol. 11 (41) , 22259-22266
Thiophene-fused boron dipyrromethenes as energy efficient near-infrared photocatalysts for radical polymerizations
Rapid near-infrared (NIR) light driven polymerizations have the potential to enable energy-efficient, benign, and multimaterial manufacturing for applications ranging from tissue engineering to soft robotics. However, achieving photopolymerization rates with NIR light that are viable for emergent additive manufacturing technologies (∼0.1–1.0 M s−1 at light intensities −2) has proven challenging due to its inherently low energy. Herein, we begin to take down these barriers through a systematic investigation of four distinct thiophene-fused boron dipyrromethene (BODIPY) photocatalysts. Through extended π-conjugation, the thiophene-fused BODIPYs effectively absorb NIR (>780 nm) light and drive efficient acrylate polymerizations upon exposure to low-intensity (2.5–40 mW cm−2) NIR light emitting diodes (LEDs). The installation of bromine atoms is shown to further improve NIR light-fueled photopolymerization efficiency by a factor of ∼1.5×. This enhancement was rationalized by the formation of long-lived spin-triplet excited states via intersystem crossing, as observed using ultrafast transient absorption spectroscopy. However, the triplet yields are modest (∼6–14%), suggesting efficient charge transfer from singlet excited states also occurs within the present photosystem. Finally, optimization of resin formulations containing non-halogenated thiophene-fused BODIPY photocatalysts is shown to provide unprecedented polymerization rates (0.33 M s−1) upon exposure to an 850 nm LED at an intensity of 20 mW cm−2. The structure–reactivity relationships identified herein provide key insights that will inform further design and optimization of energy-efficient, NIR light-driven polymerizations with utility in photocurables for coatings, adhesives, and 3D printing.
- 13 September 2023
- Published by Royal Society of Chemistry (RSC) in Journal of Materials Chemistry A
- Vol. 11 (41) , 22259-22266
Open AccessThiophene-fused boron dipyrromethenes as energy efficient near-infrared photocatalysts for radical polymerizations
Rapid near-infrared (NIR) light driven polymerizations have the potential to enable energy-efficient, benign, and multimaterial manufacturing for applications ranging from tissue engineering to soft robotics. However, achieving photopolymerization rates with NIR light that are viable for emergent additive manufacturing technologies (∼0.1–1.0 M s−1 at light intensities −2) has proven challenging due to its inherently low energy. Herein, we begin to take down these barriers through a systematic investigation of four distinct thiophene-fused boron dipyrromethene (BODIPY) photocatalysts. Through extended π-conjugation, the thiophene-fused BODIPYs effectively absorb NIR (>780 nm) light and drive efficient acrylate polymerizations upon exposure to low-intensity (2.5–40 mW cm−2) NIR light emitting diodes (LEDs). The installation of bromine atoms is shown to further improve NIR light-fueled photopolymerization efficiency by a factor of ∼1.5×. This enhancement was rationalized by the formation of long-lived spin-triplet excited states via intersystem crossing, as observed using ultrafast transient absorption spectroscopy. However, the triplet yields are modest (∼6–14%), suggesting efficient charge transfer from singlet excited states also occurs within the present photosystem. Finally, optimization of resin formulations containing non-halogenated thiophene-fused BODIPY photocatalysts is shown to provide unprecedented polymerization rates (0.33 M s−1) upon exposure to an 850 nm LED at an intensity of 20 mW cm−2. The structure–reactivity relationships identified herein provide key insights that will inform further design and optimization of energy-efficient, NIR light-driven polymerizations with utility in photocurables for coatings, adhesives, and 3D printing.
- 20 April 2023
- Published by Wiley in Angewandte Chemie
- Vol. 135 (22) , e202219140
Do The Twist: Efficient Heavy‐Atom‐Free Visible Light Polymerization Facilitated by Spin‐Orbit Charge Transfer Inter‐system Crossing
The use of visible light to drive polymerizations with spatiotemporal control offers a mild alternative to contemporary UV‐light‐based production of soft materials. In this spectral region, photoredox catalysis represents the most efficient polymerization method, yet it relies on the use of heavy‐atoms, such as precious metals or toxic halogens. Herein, spin‐orbit charge transfer intersystem crossing from boron dipyrromethene (BODIPY) dyads bearing twisted aromatic groups is shown to enable efficient visible light polymerizations in the absence of heavy‐atoms. A ≈5–15× increase in polymerization rate and improved photostability was achieved for twisted BODIPYs relative to controls. Furthermore, monomer polarity had a distinct effect on polymerization rate, which was attributed to charge transfer stabilization based on ultrafast transient absorption and phosphorescence spectroscopies. Finally, rapid and high‐resolution 3D printing with a green LED was demonstrated using the present photosystem.
- 20 April 2023
- Published by Wiley in Angewandte Chemie
- Vol. 135 (22) , e202219140
Do The Twist: Efficient Heavy‐Atom‐Free Visible Light Polymerization Facilitated by Spin‐Orbit Charge Transfer Inter‐system Crossing
The use of visible light to drive polymerizations with spatiotemporal control offers a mild alternative to contemporary UV‐light‐based production of soft materials. In this spectral region, photoredox catalysis represents the most efficient polymerization method, yet it relies on the use of heavy‐atoms, such as precious metals or toxic halogens. Herein, spin‐orbit charge transfer intersystem crossing from boron dipyrromethene (BODIPY) dyads bearing twisted aromatic groups is shown to enable efficient visible light polymerizations in the absence of heavy‐atoms. A ≈5–15× increase in polymerization rate and improved photostability was achieved for twisted BODIPYs relative to controls. Furthermore, monomer polarity had a distinct effect on polymerization rate, which was attributed to charge transfer stabilization based on ultrafast transient absorption and phosphorescence spectroscopies. Finally, rapid and high‐resolution 3D printing with a green LED was demonstrated using the present photosystem.
- 20 April 2023
- Published by Wiley in Angewandte Chemie International Edition
- Vol. 62 (22) , e202219140
Do The Twist: Efficient Heavy‐Atom‐Free Visible Light Polymerization Facilitated by Spin‐Orbit Charge Transfer Inter‐system Crossing
The use of visible light to drive polymerizations with spatiotemporal control offers a mild alternative to contemporary UV‐light‐based production of soft materials. In this spectral region, photoredox catalysis represents the most efficient polymerization method, yet it relies on the use of heavy‐atoms, such as precious metals or toxic halogens. Herein, spin‐orbit charge transfer intersystem crossing from boron dipyrromethene (BODIPY) dyads bearing twisted aromatic groups is shown to enable efficient visible light polymerizations in the absence of heavy‐atoms. A ≈5–15× increase in polymerization rate and improved photostability was achieved for twisted BODIPYs relative to controls. Furthermore, monomer polarity had a distinct effect on polymerization rate, which was attributed to charge transfer stabilization based on ultrafast transient absorption and phosphorescence spectroscopies. Finally, rapid and high‐resolution 3D printing with a green LED was demonstrated using the present photosystem.
- 20 April 2023
- Published by Wiley in Angewandte Chemie International Edition
- Vol. 62 (22) , e202219140
Do The Twist: Efficient Heavy‐Atom‐Free Visible Light Polymerization Facilitated by Spin‐Orbit Charge Transfer Inter‐system Crossing
The use of visible light to drive polymerizations with spatiotemporal control offers a mild alternative to contemporary UV‐light‐based production of soft materials. In this spectral region, photoredox catalysis represents the most efficient polymerization method, yet it relies on the use of heavy‐atoms, such as precious metals or toxic halogens. Herein, spin‐orbit charge transfer intersystem crossing from boron dipyrromethene (BODIPY) dyads bearing twisted aromatic groups is shown to enable efficient visible light polymerizations in the absence of heavy‐atoms. A ≈5–15× increase in polymerization rate and improved photostability was achieved for twisted BODIPYs relative to controls. Furthermore, monomer polarity had a distinct effect on polymerization rate, which was attributed to charge transfer stabilization based on ultrafast transient absorption and phosphorescence spectroscopies. Finally, rapid and high‐resolution 3D printing with a green LED was demonstrated using the present photosystem.