Jens Bolten
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Jens Bolten has a total of 48 co-authors. Here are the top co-authors by number of shared publications:
- Max Christian Lemme
Chair of Electronic Devices, RWTH Aachen University, Aachen, Germany
5 shared publications - Giovanna Capraro
Chair of Electronic Devices Faculty of Electrical Engineering and Information Technology RWTH Aachen University Otto-Blumenthal-Straße 25 52074 Aachen Germany
3 shared publications - Thorsten Wahlbrink
AMO GmbH Advanced Microelectronic Center Aachen Aachen Germany
3 shared publications - Georg Stefan Duesberg
Institute of Physics, University of the Bundeswehr Munich, 85579 Munich, Germany
2 shared publications - Maksim Lipkin
AMO GmbH
2 shared publications - Maximilian Prechtl
Institute of Physics, EIT 2, Faculty of Electrical Engineering and Information Technology & SENS Research Center, University of the Bundeswehr Munich, Germany
2 shared publications
Latest Publications
- Open Access
- 21 August 2023
- Published by Wiley in Advanced Photonics Research
- Vol. 4 (10)
Phase Mask Pinholes as Spatial Filters for Laser Interference Lithography
Laser resonators have outputs with Gaussian spatial beam profiles. In laser interference lithography (LIL), using such Gaussian‐shaped beams leads to an inhomogeneous exposure of the substrate. As a result, dimensions of lithography‐defined features vary significantly across the substrate. In most LIL setups, pinholes are used as filters to remove optical noise. Following a concept proposed by Hariharan et al., a phase mask can be added to these pinholes. In theory, this modification results in a more uniform beam profile, and, if applied as spatial filters in LIL, in improved exposure and hence feature size uniformity. Here, the first successful fabrication of such elements is reported on and their use in an LIL setup is demonstrated to reduce feature dimension variations in fabricated devices.
- 21 August 2023
- Published by Wiley in Advanced Photonics Research
- Vol. 4 (10)
Open AccessPhase Mask Pinholes as Spatial Filters for Laser Interference Lithography
Laser resonators have outputs with Gaussian spatial beam profiles. In laser interference lithography (LIL), using such Gaussian‐shaped beams leads to an inhomogeneous exposure of the substrate. As a result, dimensions of lithography‐defined features vary significantly across the substrate. In most LIL setups, pinholes are used as filters to remove optical noise. Following a concept proposed by Hariharan et al., a phase mask can be added to these pinholes. In theory, this modification results in a more uniform beam profile, and, if applied as spatial filters in LIL, in improved exposure and hence feature size uniformity. Here, the first successful fabrication of such elements is reported on and their use in an LIL setup is demonstrated to reduce feature dimension variations in fabricated devices.
- Open Access
Phase mask pinholes as spatial filters for laser interference lithography
Laser resonators have outputs with Gaussian spatial beam profiles. In laser interference lithography (LIL), using such Gaussian shaped beams leads to an inhomogeneous exposure of the substrate. As a result, dimensions of lithography defined features vary significantly across the substrate. In most LIL setups, pinholes are used as filters to remove optical noise. Following a concept proposed by Hariharan et. al. a phase mask can be added to these pinholes. In theory, this modification results in a more uniform beam profile, and, if applied as spatial filters in LIL, in improved exposure and hence feature size uniformity. Here, we report on the first successful fabrication of such elements and demonstrate their use in an LIL setup to reduce feature dimension variations from 47.2% to 27.5% using standard and modified pinholes, respectively.
Open AccessPhase mask pinholes as spatial filters for laser interference lithography
Laser resonators have outputs with Gaussian spatial beam profiles. In laser interference lithography (LIL), using such Gaussian shaped beams leads to an inhomogeneous exposure of the substrate. As a result, dimensions of lithography defined features vary significantly across the substrate. In most LIL setups, pinholes are used as filters to remove optical noise. Following a concept proposed by Hariharan et. al. a phase mask can be added to these pinholes. In theory, this modification results in a more uniform beam profile, and, if applied as spatial filters in LIL, in improved exposure and hence feature size uniformity. Here, we report on the first successful fabrication of such elements and demonstrate their use in an LIL setup to reduce feature dimension variations from 47.2% to 27.5% using standard and modified pinholes, respectively.
- Open Access
- 11 August 2022
- Published by Wiley in Advanced Materials Technologies
- Vol. 8 (1)
AFM‐Based Hamaker Constant Determination with Blind Tip Reconstruction
Particle contamination of extreme ultraviolet (EUV) photomasks is one of the numerous challenges in nanoscale semiconductor fabrication, since it can lead to systematic device failures when disturbing patterns are projected repeatedly onto wafers during EUV exposure. Understanding adhesion of particle contamination is key in devising a strategy for cleaning of photomasks. In this work, particle contamination is treated as a particle‐plane problem in which surface roughness and the interacting materials have major influences. For this purpose, vacuum atomic force microscopy (AFM) contact measurements to quantify the van der Waals (vdW) forces between tip and sample are performed. This as a vacuum AFM‐based methodology that combines numerical Hamaker theory and blind tip reconstruction is introduced. The Hamaker constants of 15 × 10−20 J and 13 × 10−20 J for the material systems of a silicon (Si) tip with both aluminum oxide (Al2O3) and native silicon dioxide (SiO2) on Si substrates, respectively have been determined. These methodology allows an alternative, quick and low‐cost approach to characterize the Hamaker constant within the right order of magnitude for any material combination.
- 11 August 2022
- Published by Wiley in Advanced Materials Technologies
- Vol. 8 (1)
Open AccessAFM‐Based Hamaker Constant Determination with Blind Tip Reconstruction
Particle contamination of extreme ultraviolet (EUV) photomasks is one of the numerous challenges in nanoscale semiconductor fabrication, since it can lead to systematic device failures when disturbing patterns are projected repeatedly onto wafers during EUV exposure. Understanding adhesion of particle contamination is key in devising a strategy for cleaning of photomasks. In this work, particle contamination is treated as a particle‐plane problem in which surface roughness and the interacting materials have major influences. For this purpose, vacuum atomic force microscopy (AFM) contact measurements to quantify the van der Waals (vdW) forces between tip and sample are performed. This as a vacuum AFM‐based methodology that combines numerical Hamaker theory and blind tip reconstruction is introduced. The Hamaker constants of 15 × 10−20 J and 13 × 10−20 J for the material systems of a silicon (Si) tip with both aluminum oxide (Al2O3) and native silicon dioxide (SiO2) on Si substrates, respectively have been determined. These methodology allows an alternative, quick and low‐cost approach to characterize the Hamaker constant within the right order of magnitude for any material combination.
- Open Access
- 16 August 2021
- Published by Wiley in Advanced Functional Materials
- Vol. 31 (46) , 2103936
Hybrid Devices by Selective and Conformal Deposition of PtSe2 at Low Temperatures
2D materials display very promising intrinsic material properties, with multiple applications in electronics, photonics, and sensing. In particular layered platinum diselenide has shown high potential due to its layer‐dependent tunable bandgap, low‐temperature growth, and high environmental stability. Here, the conformal and area selective (AS) low‐temperature growth of layered PtSe2 is presented defining a new paradigm for 2D material integration. The thermally‐assisted conversion of platinum which is deposited by AS atomic layer deposition to PtSe2 is demonstrated on various substrates with a distinct 3D topography. Further the viability of the approach is presented by successful on‐chip integration of hybrid semiconductor devices, namely by the manufacture of a highly sensitive ammonia sensors channel with 3D topography and fully integrated infrared‐photodetectors on silicon photonics waveguides. The presented methodologies of conformal and AS growth therefore lay the foundation for new design routes for the synthesis of more complex hybrid structures with 2D materials.
- 16 August 2021
- Published by Wiley in Advanced Functional Materials
- Vol. 31 (46) , 2103936
Open AccessHybrid Devices by Selective and Conformal Deposition of PtSe2 at Low Temperatures
2D materials display very promising intrinsic material properties, with multiple applications in electronics, photonics, and sensing. In particular layered platinum diselenide has shown high potential due to its layer‐dependent tunable bandgap, low‐temperature growth, and high environmental stability. Here, the conformal and area selective (AS) low‐temperature growth of layered PtSe2 is presented defining a new paradigm for 2D material integration. The thermally‐assisted conversion of platinum which is deposited by AS atomic layer deposition to PtSe2 is demonstrated on various substrates with a distinct 3D topography. Further the viability of the approach is presented by successful on‐chip integration of hybrid semiconductor devices, namely by the manufacture of a highly sensitive ammonia sensors channel with 3D topography and fully integrated infrared‐photodetectors on silicon photonics waveguides. The presented methodologies of conformal and AS growth therefore lay the foundation for new design routes for the synthesis of more complex hybrid structures with 2D materials.
- Open Access
- 21 June 2021
- Published by Wiley in Advanced Functional Materials
- Vol. 31 (35) , 2102929
Correlating Nanocrystalline Structure with Electronic Properties in 2D Platinum Diselenide
Platinum diselenide (PtSe2) is a 2D material with outstanding electronic and piezoresistive properties. The material can be grown at low temperatures in a scalable manner, which makes it extremely appealing for many potential electronics, photonics, and sensing applications. Here, the nanocrystalline structure of different PtSe2 thin films grown by thermally assisted conversion (TAC) is investigated and is correlated with their electronic and piezoresistive properties. Scanning transmission electron microscopy for structural analysis, X‐ray photoelectron spectroscopy (XPS) for chemical analysis, and Raman spectroscopy for phase identification are used. Electronic devices are fabricated using transferred PtSe2 films for electrical characterization and piezoresistive gauge factor measurements. The variations of crystallite size and their orientations are found to have a strong correlation with the electronic and piezoresistive properties of the films, especially the sheet resistivity and the effective charge carrier mobility. The findings may pave the way for tuning and optimizing the properties of TAC‐grown PtSe2 toward numerous applications.
- 21 June 2021
- Published by Wiley in Advanced Functional Materials
- Vol. 31 (35) , 2102929
Open AccessCorrelating Nanocrystalline Structure with Electronic Properties in 2D Platinum Diselenide
Platinum diselenide (PtSe2) is a 2D material with outstanding electronic and piezoresistive properties. The material can be grown at low temperatures in a scalable manner, which makes it extremely appealing for many potential electronics, photonics, and sensing applications. Here, the nanocrystalline structure of different PtSe2 thin films grown by thermally assisted conversion (TAC) is investigated and is correlated with their electronic and piezoresistive properties. Scanning transmission electron microscopy for structural analysis, X‐ray photoelectron spectroscopy (XPS) for chemical analysis, and Raman spectroscopy for phase identification are used. Electronic devices are fabricated using transferred PtSe2 films for electrical characterization and piezoresistive gauge factor measurements. The variations of crystallite size and their orientations are found to have a strong correlation with the electronic and piezoresistive properties of the films, especially the sheet resistivity and the effective charge carrier mobility. The findings may pave the way for tuning and optimizing the properties of TAC‐grown PtSe2 toward numerous applications.
- Open Access
- 15 August 2011
- Published by Institute of Electrical and Electronics Engineers (IEEE) in Journal of Lightwave Technology
- Vol. 29 (20) , 3054-3060
Silicon-on-Insulator Nanowire Resonators for Compact and Ultra-High Speed All-Optical Wavelength Converters
We present the development of application-specific silicon-on-insulator SOI nanowire ring and racetrack resonators designed to assist semiconductor optical amplifier (SOA)-based all-optical wavelength conversion. We demonstrate the fabrication of fix resonance racetrack resonators exhibiting coupling gaps as low as 160 nm and tunable ring resonators with coupling gaps <; 90 nm. The resonators are cascaded after commercial 40 Gb/s SOAs to realize chirp filtering of the optical data signals through high-resolution spectral sampling. We experimentally demonstrate inverted and non-inverted SOI resonator-assisted all-optical wavelength conversion at 40 Gb/s and 160 Gb/s with power penalties <; 3 dB.
- 15 August 2011
- Published by Institute of Electrical and Electronics Engineers (IEEE) in Journal of Lightwave Technology
- Vol. 29 (20) , 3054-3060
Open AccessSilicon-on-Insulator Nanowire Resonators for Compact and Ultra-High Speed All-Optical Wavelength Converters
We present the development of application-specific silicon-on-insulator SOI nanowire ring and racetrack resonators designed to assist semiconductor optical amplifier (SOA)-based all-optical wavelength conversion. We demonstrate the fabrication of fix resonance racetrack resonators exhibiting coupling gaps as low as 160 nm and tunable ring resonators with coupling gaps <; 90 nm. The resonators are cascaded after commercial 40 Gb/s SOAs to realize chirp filtering of the optical data signals through high-resolution spectral sampling. We experimentally demonstrate inverted and non-inverted SOI resonator-assisted all-optical wavelength conversion at 40 Gb/s and 160 Gb/s with power penalties <; 3 dB.
- 1 June 2010
- Published by IOP Publishing in Journal of Optics
- Vol. 12 (6) , 065003
Design and optical characterization of photonic crystal lasers with organic gain material
- 1 June 2010
- Published by IOP Publishing in Journal of Optics
- Vol. 12 (6) , 065003
Design and optical characterization of photonic crystal lasers with organic gain material
- 1 May 2007
- Published by Elsevier in Microelectronic Engineering
- Vol. 84 (5-8) , 904-908
Improved mold fabrication for the definition of high quality nanopatterns by Soft UV-Nanoimprint lithography using diluted PDMS material
- 1 May 2007
- Published by Elsevier in Microelectronic Engineering
- Vol. 84 (5-8) , 904-908
Improved mold fabrication for the definition of high quality nanopatterns by Soft UV-Nanoimprint lithography using diluted PDMS material