Muhammad AlHadi Zulkefle
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Muhammad AlHadi Zulkefle has a total of 19 co-authors. Here are the top co-authors by number of shared publications:
- Sukreen Hana Herman
Universiti Teknologi MARA
9 shared publications - Wan Fazlida Hanim Abdullah
Universiti Teknologi MARA
7 shared publications - Khairul Aimi Yusof
NANO-Electronic Centre (NET), Faculty of Electrical Engineering, Universiti Teknologi MARA, 40450 Shah Alam, Selangor, Malaysia
4 shared publications - Rohanieza Abdul Rahman
NANO-Electronic Centre (NET), Faculty of Electrical Engineering, Universiti Teknologi MARA, 40450 Shah Alam, Selangor, Malaysia
4 shared publications - Aimi Bazilah Binti Rosli
Integrated Sensors Research Group, School of Electrical Engineering, College of Engineering, Universiti Teknologi MARA (UiTM), Shah Alam 40450, Selangor, Malaysia
3 shared publications - Rohanieza Abdul Rahman
NANO-ElecTronic Centre, Faculty of Electrical Engineering, Universiti Teknologi Mara (UiTM), 40450 Shah Alam, Selangor, Malaysia
3 shared publications
Latest Publications
- 28 October 2022
- Published by Elsevier in International Journal of Hydrogen Energy
- Vol. 48 (4) , 1636-1648
Post-deposition heat treatment effect on pH sensing behavior of chemical bath deposited nanostructured zinc oxide
- 28 October 2022
- Published by Elsevier in International Journal of Hydrogen Energy
- Vol. 48 (4) , 1636-1648
Post-deposition heat treatment effect on pH sensing behavior of chemical bath deposited nanostructured zinc oxide
- Open Access
Highly Sensitive and Selective Sol-Gel Spin-Coated Composite TiO2–PANI Thin Films for EGFET-pH Sensor
A highly selective and sensitive EGFET-pH sensor based on composite TiO2–PANI had been developed in this work. A sol-gel titanium dioxide (TiO2) and the composite of TiO2 with semiconducting polyaniline (PANI) were deposited using a simple spin-coating method on an indium tin oxide (ITO) substrate. The films have been explored as a sensing electrode (SE) of extended gate field-effect transistor (EGFET) for pH applications in the range of pH 2 to 12. The pH sensitivities between TiO2, TiO2–PANI bilayer composite, and TiO2–PANI composite thin films were discussed. Among these, the TiO2–PANI composite thin film showed a super-Nernstian behavior with high sensitivity of 66.1 mV/pH and linearity of 0.9931; good repeatability with a standard deviation of 0.49%; a low hysteresis value of 3 mV; and drift rates of 4.96, 5.54, and 3.32 mV/h in pH 4, 7, and 10, respectively, for 6 h. Upon applying the TiO2–PANI composite as the SE for nitrate measurement, low sensitivity of 12.9 mV/dec was obtained, indicating that this film is a highly selective sensing electrode as a pH sensor. The surface morphology and crystallinity of the thin films were also discussed.
Open AccessHighly Sensitive and Selective Sol-Gel Spin-Coated Composite TiO2–PANI Thin Films for EGFET-pH Sensor
A highly selective and sensitive EGFET-pH sensor based on composite TiO2–PANI had been developed in this work. A sol-gel titanium dioxide (TiO2) and the composite of TiO2 with semiconducting polyaniline (PANI) were deposited using a simple spin-coating method on an indium tin oxide (ITO) substrate. The films have been explored as a sensing electrode (SE) of extended gate field-effect transistor (EGFET) for pH applications in the range of pH 2 to 12. The pH sensitivities between TiO2, TiO2–PANI bilayer composite, and TiO2–PANI composite thin films were discussed. Among these, the TiO2–PANI composite thin film showed a super-Nernstian behavior with high sensitivity of 66.1 mV/pH and linearity of 0.9931; good repeatability with a standard deviation of 0.49%; a low hysteresis value of 3 mV; and drift rates of 4.96, 5.54, and 3.32 mV/h in pH 4, 7, and 10, respectively, for 6 h. Upon applying the TiO2–PANI composite as the SE for nitrate measurement, low sensitivity of 12.9 mV/dec was obtained, indicating that this film is a highly selective sensing electrode as a pH sensor. The surface morphology and crystallinity of the thin films were also discussed.
- Open Access
- 7 June 2021
- Published by Penerbit UTM Press in Jurnal Teknologi (Sciences & Engineering)
- Vol. 83 (4) , 119-125
EVALUATION ON THE EGFET PH SENSING PERFORMANCE OF SOL-GEL SPIN COATED TITANIUM DIOXIDE THIN FILM
For this study, TiO2 thin film was fabricated using the sol-gel spin coating method. The fabricated film was then applied as a sensing membrane in an extended gate field effect transistor (EGFET) pH sensor system. The pH sensing performance of the sol-gel spin-coated TiO2 was evaluated in terms of sensitivity, linearity, and hysteresis where the value obtained was 58.70 mV/pH, 0.9922, and 86.17 mV respectively. The drift rate of the sample when being measured for 12 consecutive hours was also determined where measurement in pH 4, pH 7, and pH 10 yield drift rate of 1.72 mV/h, 4.14 mV/h, and 6.05 mV/h respectively. Besides that, the TiO2 was characterized for its thickness (24.32 nm) and surface roughness (5.129 nm). From the results obtained, it was found that sol-gel spin-coated TiO2 thin film with thickness between 20 - 29 nm will have high pH sensitivity (more than 50 mV/pH).
- 7 June 2021
- Published by Penerbit UTM Press in Jurnal Teknologi (Sciences & Engineering)
- Vol. 83 (4) , 119-125
Open AccessEVALUATION ON THE EGFET PH SENSING PERFORMANCE OF SOL-GEL SPIN COATED TITANIUM DIOXIDE THIN FILM
For this study, TiO2 thin film was fabricated using the sol-gel spin coating method. The fabricated film was then applied as a sensing membrane in an extended gate field effect transistor (EGFET) pH sensor system. The pH sensing performance of the sol-gel spin-coated TiO2 was evaluated in terms of sensitivity, linearity, and hysteresis where the value obtained was 58.70 mV/pH, 0.9922, and 86.17 mV respectively. The drift rate of the sample when being measured for 12 consecutive hours was also determined where measurement in pH 4, pH 7, and pH 10 yield drift rate of 1.72 mV/h, 4.14 mV/h, and 6.05 mV/h respectively. Besides that, the TiO2 was characterized for its thickness (24.32 nm) and surface roughness (5.129 nm). From the results obtained, it was found that sol-gel spin-coated TiO2 thin film with thickness between 20 - 29 nm will have high pH sensitivity (more than 50 mV/pH).
- 1 January 2018
- Published by AIP Publishing in AIP Conference Proceedings
- Vol. 1963 (1) , 020063
Influence of annealing time on pH sensitivity of ZnO sensing membrane for EGFET sensor
Solid-state materials have becomes essential in recent technological advancements. This study also utilized solid-state material but in form of thin films to sense hydrogen ions in solutions. Fabrication of ZnO thin film was done using sol-gel spin coating technique. In an attempt to increase the pH sensitivity of the produced film, prolonging of annealing time was done. It was found that the increase in annealing time from 15 minutes to 30 minutes had managed to improve the sensitivity by 4.35%. The optimum pH sensitivity and linearity obtained in this study is 50.40 mV/pH and 0.9911 respectively.
- 1 January 2018
- Published by AIP Publishing in AIP Conference Proceedings
- Vol. 1963 (1) , 020063
Influence of annealing time on pH sensitivity of ZnO sensing membrane for EGFET sensor
Solid-state materials have becomes essential in recent technological advancements. This study also utilized solid-state material but in form of thin films to sense hydrogen ions in solutions. Fabrication of ZnO thin film was done using sol-gel spin coating technique. In an attempt to increase the pH sensitivity of the produced film, prolonging of annealing time was done. It was found that the increase in annealing time from 15 minutes to 30 minutes had managed to improve the sensitivity by 4.35%. The optimum pH sensitivity and linearity obtained in this study is 50.40 mV/pH and 0.9911 respectively.
- 1 January 2018
- Published by AIP Publishing in AIP Conference Proceedings
- Vol. 1963 (1) , 020064
Layer configurations comparison of bilayer-films for EGFET pH sensor application
The comparison between bilayer configurations were presented in this paper. TiO2 and ZnO layer configurations were manipulated in order to investigate which configuration produce highest sensing performance to be applied as EGFET pH sensor. Both of the materials were deposited together as the bilayer film. The configurations were manipulated between TiO2/ZnO and ZnO/TiO2. ITO was used as the substrate in this study and both of the materials were deposited by using sol-gel spin coating technique. After deposition process, these bilayer film then undergone for EGFET pH sensor measurement and physical characterization. The EGFET pH sensor measurement was done by dipping the fabricated bilayer film into three different pH values, which is pH4, pH7 and pH10. Bilayer film act as the pH-sensitive membrane, which connected to the commercial metal-oxide semiconductor FET (MOSFET). This MOSFET was connected to the interfacing circuit. Voltage output obtained were recorded and the graph was plotted by using the data recorded. Based on the EGFET pH sensor measurement, TiO2/ZnO bilayer film exhibit higher sensing performance, compared with ZnO/TiO2. TiO2/ZnO bilayer film produced 53.10 mV/pH with the linearity value of 0.9913. Afterwards, fabricated bilayer films then were characterized with AFM to explore their surface roughness and surface topography behavior.
- 1 January 2018
- Published by AIP Publishing in AIP Conference Proceedings
- Vol. 1963 (1) , 020064
Layer configurations comparison of bilayer-films for EGFET pH sensor application
The comparison between bilayer configurations were presented in this paper. TiO2 and ZnO layer configurations were manipulated in order to investigate which configuration produce highest sensing performance to be applied as EGFET pH sensor. Both of the materials were deposited together as the bilayer film. The configurations were manipulated between TiO2/ZnO and ZnO/TiO2. ITO was used as the substrate in this study and both of the materials were deposited by using sol-gel spin coating technique. After deposition process, these bilayer film then undergone for EGFET pH sensor measurement and physical characterization. The EGFET pH sensor measurement was done by dipping the fabricated bilayer film into three different pH values, which is pH4, pH7 and pH10. Bilayer film act as the pH-sensitive membrane, which connected to the commercial metal-oxide semiconductor FET (MOSFET). This MOSFET was connected to the interfacing circuit. Voltage output obtained were recorded and the graph was plotted by using the data recorded. Based on the EGFET pH sensor measurement, TiO2/ZnO bilayer film exhibit higher sensing performance, compared with ZnO/TiO2. TiO2/ZnO bilayer film produced 53.10 mV/pH with the linearity value of 0.9913. Afterwards, fabricated bilayer films then were characterized with AFM to explore their surface roughness and surface topography behavior.
- Open Access
- 10 October 2016
- Published by Wiley in Journal of Sensors
- Vol. 2016, 1-8
Spin Speed and Duration Dependence of TiO2Thin Films pH Sensing Behavior
Titanium dioxide (TiO2) thin films were applied as the sensing membrane of an extended-gate field-effect transistor (EGFET) pH sensor. TiO2thin films were deposited by spin coating method and the influences of the spin speed and spin duration on the pH sensing behavior of TiO2thin films were investigated. The spin coated TiO2thin films were connected to commercial metal-oxide-semiconductor field-effect transistor (MOSFET) to form the extended gates and the MOSFET was integrated in a readout interfacing circuit to complete the EGFET pH sensor system. For the spin speed parameter investigation, the highest sensitivity was obtained for the sample spun at 3000 rpm at a fixed spinning time of 60 s, which was 60.3 mV/pH. The sensitivity was further improved to achieve 68 mV/pH with good linearity of 0.9943 when the spin time was 75 s at the speed of 3000 rpm.
- 10 October 2016
- Published by Wiley in Journal of Sensors
- Vol. 2016, 1-8
Open AccessSpin Speed and Duration Dependence of TiO2Thin Films pH Sensing Behavior
Titanium dioxide (TiO2) thin films were applied as the sensing membrane of an extended-gate field-effect transistor (EGFET) pH sensor. TiO2thin films were deposited by spin coating method and the influences of the spin speed and spin duration on the pH sensing behavior of TiO2thin films were investigated. The spin coated TiO2thin films were connected to commercial metal-oxide-semiconductor field-effect transistor (MOSFET) to form the extended gates and the MOSFET was integrated in a readout interfacing circuit to complete the EGFET pH sensor system. For the spin speed parameter investigation, the highest sensitivity was obtained for the sample spun at 3000 rpm at a fixed spinning time of 60 s, which was 60.3 mV/pH. The sensitivity was further improved to achieve 68 mV/pH with good linearity of 0.9943 when the spin time was 75 s at the speed of 3000 rpm.
- Open Access
- 1 January 2016
- Published by Wiley in Journal of Sensors
- Vol. 2016, 1-9
EGFET pH Sensor Performance Dependence on Sputtered TiO2Sensing Membrane Deposition Temperature
Titanium dioxide (TiO2) thin films were sputtered by radio frequency (RF) magnetron sputtering method and have been employed as the sensing membrane of an extended gate field effect transistor (EGFET) for pH sensing detection application. The TiO2thin films were deposited onto indium tin oxide (ITO) coated glass substrates at room temperature and 200°C, respectively. The effect of deposition temperature on thin film properties and pH detection application was analyzed. The TiO2samples used as the sensing membrane for EGFET pH-sensor and the current-voltage (I-V), hysteresis, and drift characteristics were examined. The sensitivity of TiO2EGFET sensing membrane was obtained from the transfer characteristic (I-V) curves for different substrate heating temperatures. TiO2thin film sputtered at room temperature achieved higher sensitivity of 59.89 mV/pH compared to the one deposited at 200°C indicating lower sensitivity of 37.60 mV/pH. Moreover the hysteresis and the drift of TiO2thin film deposited at room temperature showed lower values compared to the one at 200°C. We have also tested the effect of operating temperature on the performance of the EGFET pH-sensing and found that the temperature effect was very minimal.
- 1 January 2016
- Published by Wiley in Journal of Sensors
- Vol. 2016, 1-9
Open AccessEGFET pH Sensor Performance Dependence on Sputtered TiO2Sensing Membrane Deposition Temperature
Titanium dioxide (TiO2) thin films were sputtered by radio frequency (RF) magnetron sputtering method and have been employed as the sensing membrane of an extended gate field effect transistor (EGFET) for pH sensing detection application. The TiO2thin films were deposited onto indium tin oxide (ITO) coated glass substrates at room temperature and 200°C, respectively. The effect of deposition temperature on thin film properties and pH detection application was analyzed. The TiO2samples used as the sensing membrane for EGFET pH-sensor and the current-voltage (I-V), hysteresis, and drift characteristics were examined. The sensitivity of TiO2EGFET sensing membrane was obtained from the transfer characteristic (I-V) curves for different substrate heating temperatures. TiO2thin film sputtered at room temperature achieved higher sensitivity of 59.89 mV/pH compared to the one deposited at 200°C indicating lower sensitivity of 37.60 mV/pH. Moreover the hysteresis and the drift of TiO2thin film deposited at room temperature showed lower values compared to the one at 200°C. We have also tested the effect of operating temperature on the performance of the EGFET pH-sensing and found that the temperature effect was very minimal.
- 1 January 2016
- Published by AIP Publishing in AIP Conference Proceedings
- Vol. 1733 (1) , 020059
Characteristics of TiO2/ZnO bilayer film towards pH sensitivity prepared by different spin coating deposition process
In this study, titanium dioxide (TiO2) and zinc oxide (ZnO) bilayer film for pH sensing application will be presented. TiO2/ZnO bilayer film with different speed of spin-coating process was deposited on Indium Tin Oxide (ITO), prepared by sol-gel method. This fabricated bilayer film was used as sensing membrane for Extended Gate Field-Effect Transistor (EGFET) for pH sensing application. Experimental results indicated that the sensor is able to detect the sensitivity towards pH buffer solution. In order to obtained the result, sensitivity measurement was done by using the EGFET setup equipment with constant-current (100 µA) and constant-voltage (0.3 V) biasing interfacing circuit. TiO2/ZnO bilayer film which the working electrode, act as the pH-sensitive membrane was connected to a commercial metal-oxide semiconductor FET (MOSFET). This MOSFET then was connected to the interfacing circuit. The sensitivity of the TiO2 thin film towards pH buffer solution was measured by dipping the sensing membrane in pH4, pH7 and pH10 buffer solution. These thin films were characterized by using Field Emission Scanning Electron Microscope (FESEM) to obtain the surface morphology of the composite bilayer films. In addition, I-V measurement was done in order to determine the electrical properties of the bilayer films. According to the result obtained in this experiment, bilayer film that spin at 4000 rpm, gave highest sensitivity which is 52.1 mV/pH. Relating the I-V characteristic of the thin films and sensitivity, the sensing membrane with higher conductivity gave better sensitivity.
- 1 January 2016
- Published by AIP Publishing in AIP Conference Proceedings
- Vol. 1733 (1) , 020059
Characteristics of TiO2/ZnO bilayer film towards pH sensitivity prepared by different spin coating deposition process
In this study, titanium dioxide (TiO2) and zinc oxide (ZnO) bilayer film for pH sensing application will be presented. TiO2/ZnO bilayer film with different speed of spin-coating process was deposited on Indium Tin Oxide (ITO), prepared by sol-gel method. This fabricated bilayer film was used as sensing membrane for Extended Gate Field-Effect Transistor (EGFET) for pH sensing application. Experimental results indicated that the sensor is able to detect the sensitivity towards pH buffer solution. In order to obtained the result, sensitivity measurement was done by using the EGFET setup equipment with constant-current (100 µA) and constant-voltage (0.3 V) biasing interfacing circuit. TiO2/ZnO bilayer film which the working electrode, act as the pH-sensitive membrane was connected to a commercial metal-oxide semiconductor FET (MOSFET). This MOSFET then was connected to the interfacing circuit. The sensitivity of the TiO2 thin film towards pH buffer solution was measured by dipping the sensing membrane in pH4, pH7 and pH10 buffer solution. These thin films were characterized by using Field Emission Scanning Electron Microscope (FESEM) to obtain the surface morphology of the composite bilayer films. In addition, I-V measurement was done in order to determine the electrical properties of the bilayer films. According to the result obtained in this experiment, bilayer film that spin at 4000 rpm, gave highest sensitivity which is 52.1 mV/pH. Relating the I-V characteristic of the thin films and sensitivity, the sensing membrane with higher conductivity gave better sensitivity.
- Open Access
- 19 November 2015
- Published by IOP Publishing in IOP Conference Series: Materials Science and Engineering
- Vol. 99 (1) , 012019
Effect of Annealing Time Process on the pH Sensitivity of Spin-coated TiO2/ ZnO Bilayer Film
This paper presents an investigation on titanium dioxide (TiO 2) and zinc oxide (ZnO) bilayer film, which is used as sensing membrane for extended-gate field effect transistor (EGFET) for pH sensing application. TiO 2 /ZnO thin films were deposited using sol-gel spin coating method on indium tin oxide (ITO) substrates. After the deposition, the bilayer films were annealed at constant temperatures which is 400 °C for 15, 30, 40 and 60 minutes. The sensitivity of the TiO 2 thin film towards pH buffer solution was measured by dipping the sensing membrane in pH4, pH7 and pH10 buffer solution. By varying the annealing time, we found that the TiO 2 /ZnO thin film annealed at 400°C for 15 minutes gave the highest sensitivity compared to other annealing conditions, with the value of 64.87 mV/pH.
- 19 November 2015
- Published by IOP Publishing in IOP Conference Series: Materials Science and Engineering
- Vol. 99 (1) , 012019
Open AccessEffect of Annealing Time Process on the pH Sensitivity of Spin-coated TiO2/ ZnO Bilayer Film
This paper presents an investigation on titanium dioxide (TiO 2) and zinc oxide (ZnO) bilayer film, which is used as sensing membrane for extended-gate field effect transistor (EGFET) for pH sensing application. TiO 2 /ZnO thin films were deposited using sol-gel spin coating method on indium tin oxide (ITO) substrates. After the deposition, the bilayer films were annealed at constant temperatures which is 400 °C for 15, 30, 40 and 60 minutes. The sensitivity of the TiO 2 thin film towards pH buffer solution was measured by dipping the sensing membrane in pH4, pH7 and pH10 buffer solution. By varying the annealing time, we found that the TiO 2 /ZnO thin film annealed at 400°C for 15 minutes gave the highest sensitivity compared to other annealing conditions, with the value of 64.87 mV/pH.