N. Rakesh
N. Rakesh has a total of 13 co-authors. Here are the top co-authors by number of shared publications:
- A. N. Shankar
Department of HSE & Civil Engineering
2 shared publications - Guruprasad Balachandran
Department of Mechanical Engineering
1 shared publication - K. Meena
Department of Computer Science and Engineering, GITAM School of Technology, GITAM University, Bengaluru Campus, India
1 shared publication - M. Hariprabhu
Department of Electrical and Electronics Engineering
1 shared publication - Madhan Mohankumar
Department of Robotics and Automation, Easwari Engineering College, Ramapuram, Chennai, India
1 shared publication - Nahom Daniel
Department of Chemical Engineering
1 shared publication
Latest Publications
- RetractedOpen Access
- 1 January 2021
- Published by Wiley in Advances in Materials Science and Engineering
- Vol. 2021 (1)
[Retracted] Multiobjective Optimization of Mechanical Properties on Sisal‐Glass Fiber‐Reinforced Hybrid Composites Using Response Surface Methodology and LINGO Analysis
The aim of this research work was to develop the optimal mechanical properties, namely, tensile strength, flexural strength, and impact strength of sisal and glass fiber‐reinforced polymer hybrid composites. The sisal, in the form of short fiber, is randomly used as reinforcements for composite materials, which is rich in cellulose, economical, and easily available as well as glass fibers have low cost and have good mechanical properties. In addition, epoxy resin and hardener were for the fabrication of composites by compression molding. The selected materials are fabricated by compression molding in various concentrations on volume basics. The combination of material compositions is obtained from the design of experiments and optimum parameters determined by the Response Surface Methodology (RSM). From the investigation of mechanical properties, the sisal is the most significant factor and verified by ANOVA techniques. The multiobjective optimal levels of factors are obtained by LINGO analysis.
- 1 January 2021
- Published by Wiley in Advances in Materials Science and Engineering
- Vol. 2021 (1)
RetractedOpen Access[Retracted] Multiobjective Optimization of Mechanical Properties on Sisal‐Glass Fiber‐Reinforced Hybrid Composites Using Response Surface Methodology and LINGO Analysis
The aim of this research work was to develop the optimal mechanical properties, namely, tensile strength, flexural strength, and impact strength of sisal and glass fiber‐reinforced polymer hybrid composites. The sisal, in the form of short fiber, is randomly used as reinforcements for composite materials, which is rich in cellulose, economical, and easily available as well as glass fibers have low cost and have good mechanical properties. In addition, epoxy resin and hardener were for the fabrication of composites by compression molding. The selected materials are fabricated by compression molding in various concentrations on volume basics. The combination of material compositions is obtained from the design of experiments and optimum parameters determined by the Response Surface Methodology (RSM). From the investigation of mechanical properties, the sisal is the most significant factor and verified by ANOVA techniques. The multiobjective optimal levels of factors are obtained by LINGO analysis.
- RetractedOpen Access
- 1 January 2021
- Published by Wiley in Advances in Materials Science and Engineering
- Vol. 2021 (1)
[Retracted] A Comparative Study on Crack‐Healing Ability of Al2O3/SiC Structural Ceramic Composites Synthesized by Microwave Sintering and Conventional Electrical Sintering
This study was conducted to assess and compare the crack‐healing ability of conventional electrical sintered and microwave sintered Al2O3/x wt. % SiC (x = 5, 10, 15, and 20) structural ceramic composites. The crack‐healing ability of both conventional electrical sintered and microwave sintered specimens was studied by introducing a crack of ∼100 µm length by Vickers’s indentation and conducting a heat treatment at 1200°C for dwell time of 1 h in air. The flexural or bending strength of sintered, cracked, and crack‐healed specimens was determined by three‐point bending test, and the phase variations by X‐ray diffraction and SEM micrographs before and after crack‐healing of both the sintering methods were studied and compared. The results show that almost all the specimens recovered their strength after crack‐healing, but the strength of microwave sintered Al2O3/SiC structural ceramic composites has been shown to be better than that of conventional electrical sintered Al2O3/SiC structural ceramic composites. The microwave sintered crack‐healed Al2O3/10 wt. % SiC specimen shows higher flexural strength of 794 MPa, which was 105% when compared with conventional electrical sintered Al2O3/10 wt. % SiC and crack‐healed Al2O3/10 wt. % SiC specimen. It was found by X‐ray diffractogram that before crack‐healing, all the conventional electrical sintered samples have SiO2 phase which reduce the crack‐healing ability and microwave sintered samples with 15 and 20 wt. % SiC show lesser SiO2 phase and 5 and 10 wt. % SiC samples have no SiO2 phase before crack‐healing. However, after crack‐healing treatment, all the samples have distinct SiO2 phase along with Al2O3 and SiC phases. Microwave sintered Al2O3/10 wt. % SiC specimen cracks were fully healed which was evident in SEM micrographs.
- 1 January 2021
- Published by Wiley in Advances in Materials Science and Engineering
- Vol. 2021 (1)
RetractedOpen Access[Retracted] A Comparative Study on Crack‐Healing Ability of Al2O3/SiC Structural Ceramic Composites Synthesized by Microwave Sintering and Conventional Electrical Sintering
This study was conducted to assess and compare the crack‐healing ability of conventional electrical sintered and microwave sintered Al2O3/x wt. % SiC (x = 5, 10, 15, and 20) structural ceramic composites. The crack‐healing ability of both conventional electrical sintered and microwave sintered specimens was studied by introducing a crack of ∼100 µm length by Vickers’s indentation and conducting a heat treatment at 1200°C for dwell time of 1 h in air. The flexural or bending strength of sintered, cracked, and crack‐healed specimens was determined by three‐point bending test, and the phase variations by X‐ray diffraction and SEM micrographs before and after crack‐healing of both the sintering methods were studied and compared. The results show that almost all the specimens recovered their strength after crack‐healing, but the strength of microwave sintered Al2O3/SiC structural ceramic composites has been shown to be better than that of conventional electrical sintered Al2O3/SiC structural ceramic composites. The microwave sintered crack‐healed Al2O3/10 wt. % SiC specimen shows higher flexural strength of 794 MPa, which was 105% when compared with conventional electrical sintered Al2O3/10 wt. % SiC and crack‐healed Al2O3/10 wt. % SiC specimen. It was found by X‐ray diffractogram that before crack‐healing, all the conventional electrical sintered samples have SiO2 phase which reduce the crack‐healing ability and microwave sintered samples with 15 and 20 wt. % SiC show lesser SiO2 phase and 5 and 10 wt. % SiC samples have no SiO2 phase before crack‐healing. However, after crack‐healing treatment, all the samples have distinct SiO2 phase along with Al2O3 and SiC phases. Microwave sintered Al2O3/10 wt. % SiC specimen cracks were fully healed which was evident in SEM micrographs.