William Phillips
Research Subjects
William Phillips has a total of 14 co-authors. Here are the top co-authors by number of shared publications:
- Kam Ng
Department of Civil and Architectural Engineering and Construction Management, University of Wyoming, Laramie, USA
2 shared publications - Nauman Aslam
Northumbria University
2 shared publications - Prapti Giri
Terracon, Cedar Rapids, IA, USA
2 shared publications A. Elgallad
Dalhousie University
1 shared publication- Abdelhay A. Sallam
Electrical Engineering Department., Suez Canal University., Port Said., Egypt
1 shared publication - Abdullah Alomari
Department of Computer Science, Al-Baha University, Al-Baha, Saudi Arabia
1 shared publication
Latest Publications
- Open Access
- 1 June 2022
- Published by Emerald Publishing in Geotechnical Research
- Vol. 9 (2) , 83-94
Monitoring toppling failures using wireless inertial measurement unit sensors
A topple is a common rock slope failure – and usually the cause of a rockfall – that depends on the slope and rock geometries. This paper presents a laboratory simulation and field generation of a single-column rock topple failure. Innovative inertial measurement unit (IMU) sensors were used to collect three-dimensional acceleration and angular velocity data during four laboratory experiments to understand and characterise general toppling behaviours. A topple is identified by the gradual change in at least two gravity accelerations, the continuous increase in at least one of the angular velocities and a significant change in the linear acceleration in the direction of toppling. A field experiment showed similar sensor data patterns to those observed from the laboratory experiments. An isolated-block stability analysis of a single-column topple provides the basis for incorporating the IMU sensors into the development of future monitoring and early warning systems.
- 1 June 2022
- Published by Emerald Publishing in Geotechnical Research
- Vol. 9 (2) , 83-94
Open AccessMonitoring toppling failures using wireless inertial measurement unit sensors
A topple is a common rock slope failure – and usually the cause of a rockfall – that depends on the slope and rock geometries. This paper presents a laboratory simulation and field generation of a single-column rock topple failure. Innovative inertial measurement unit (IMU) sensors were used to collect three-dimensional acceleration and angular velocity data during four laboratory experiments to understand and characterise general toppling behaviours. A topple is identified by the gradual change in at least two gravity accelerations, the continuous increase in at least one of the angular velocities and a significant change in the linear acceleration in the direction of toppling. A field experiment showed similar sensor data patterns to those observed from the laboratory experiments. An isolated-block stability analysis of a single-column topple provides the basis for incorporating the IMU sensors into the development of future monitoring and early warning systems.
- 24 June 2021
- Published by Springer Nature in Geotechnical and Geological Engineering
- Vol. 40 (1) , 367-381
Monitoring Soil Slide-Flow Using Wireless Sensor Network-Inertial Measurement Unit System
- 24 June 2021
- Published by Springer Nature in Geotechnical and Geological Engineering
- Vol. 40 (1) , 367-381
Monitoring Soil Slide-Flow Using Wireless Sensor Network-Inertial Measurement Unit System
- 20 March 2017
- Published by Springer Nature in Wireless Networks
- Vol. 24 (7) , 2589-2607
New path planning model for mobile anchor-assisted localization in wireless sensor networks
- 20 March 2017
- Published by Springer Nature in Wireless Networks
- Vol. 24 (7) , 2589-2607
New path planning model for mobile anchor-assisted localization in wireless sensor networks
- Open Access
- 30 September 2015
- Published by Wiley in Mobile Information Systems
- Vol. 2015, 1-16
QPRD: QoS-Aware Peering Routing Protocol for Delay-Sensitive Data in Hospital Body Area Network
Consistent performance, energy efficiency, and reliable transfer of data are critical factors for real-time monitoring of a patient’s data, especially in a hospital environment. In this paper, a routing protocol is proposed by considering the QoS requirements of the Body Area Network (BAN) data packets. A mechanism for handling delay-sensitive packets is provided by this protocol. Moreover, linear programming based modeling along with graphical analysis is also done. Extensive simulations using the OMNeT++ based simulator Castalia 3.2 illustrate that the proposed algorithm provides better performance than other QoS-aware routing protocols in terms of higher successful transmission rates (throughputs), lower overall network traffic, no packets dropped due to MAC buffer overflow, and fewer numbers of packet time outs in both the mobile and static patient scenarios. The scalability of the protocol is demonstrated by simulating a 24-bed real hospital environment with 49 nodes. It is shown that, even in the larger real hospital scenario requiring the transmission of delay-sensitive data packets with stringent delay requirements, QPRD outperforms comparable protocols.
- 30 September 2015
- Published by Wiley in Mobile Information Systems
- Vol. 2015, 1-16
Open AccessQPRD: QoS-Aware Peering Routing Protocol for Delay-Sensitive Data in Hospital Body Area Network
Consistent performance, energy efficiency, and reliable transfer of data are critical factors for real-time monitoring of a patient’s data, especially in a hospital environment. In this paper, a routing protocol is proposed by considering the QoS requirements of the Body Area Network (BAN) data packets. A mechanism for handling delay-sensitive packets is provided by this protocol. Moreover, linear programming based modeling along with graphical analysis is also done. Extensive simulations using the OMNeT++ based simulator Castalia 3.2 illustrate that the proposed algorithm provides better performance than other QoS-aware routing protocols in terms of higher successful transmission rates (throughputs), lower overall network traffic, no packets dropped due to MAC buffer overflow, and fewer numbers of packet time outs in both the mobile and static patient scenarios. The scalability of the protocol is demonstrated by simulating a 24-bed real hospital environment with 49 nodes. It is shown that, even in the larger real hospital scenario requiring the transmission of delay-sensitive data packets with stringent delay requirements, QPRD outperforms comparable protocols.
- 1 January 2007
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- No. 23319852,p. 650-654
Energy Efficient Cluster Formation Using A Multi-Criterion Optimization Technique for Wireless Sensor Networks
- 1 January 2007
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- No. 23319852,p. 650-654
Energy Efficient Cluster Formation Using A Multi-Criterion Optimization Technique for Wireless Sensor Networks