Yuntang Li
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Yuntang Li has a total of 70 co-authors. Here are the top co-authors by number of shared publications:
Yuan Chen
College of Mechanical and Electrical Engineering, China Jiliang University , Hangzhou 310018
12 shared publicationsBingqing Wang
College of Mechanical and Electrical Engineering, China Jiliang University , Hangzhou 310018
10 shared publications- Bingqing Wang
China Jiliang University College of Mechanical and Electrical Engineering
10 shared publications - Yuan Chen
China Jiliang University College of Mechanical and Electrical Engineering
8 shared publications - Jie Jin
College of Mechanical and Electrical Engineering, China Jiliang University , Hangzhou 310018
7 shared publications - Xiaolu Li
College of Mechanical and Electrical Engineering, China Jiliang University, Hangzhou 310018, China
7 shared publications
Latest Publications
- 1 September 2026
- Published by AIP Publishing in Physics of Fluids
- Vol. 38 (9)
Effect and correction of turbulence coefficient on performance calculation of aerostatic thrust bearing lubricated by supercritical CO2
In this article, the flow field and bearing performance of aerostatic thrust bearing (ATB) lubricated by supercritical CO2 (ATB-SCO2) are analyzed by solving the Reynolds equation with the laminar model and four turbulence models (Hirs model, Ng–Pan model, Constantinescu model, and Elrod–Ng model) through the finite difference method. The calculation accuracy and efficiency of ATB-SCO2 performance under different flow and CO2 models are discussed. Furthermore, the turbulence coefficient is corrected by analyzing the influences of empirical coefficient and empirical exponent on the calculation results of ATB-SCO2 performance. The turbulence models with turbulence coefficients increase the pressure and Reynolds number but decrease the velocity in the lubricating film. The ideal gas assumption shows the same effect (i.e., an increase) on pressure but opposite effects (i.e., an increase) on Reynolds number and velocity. Moreover, both turbulence models with turbulence coefficients and ideal gas assumption increase the bearing load capacity and stiffness but reduce the mass flow rate. Compared to Elrod–Ng model, the calculation adopting laminar model, Hirs model, Ng–Pan model, and Constantinescu model are less accurate but more efficient. The accuracy using the model with corrected turbulence coefficient improves by 86.02%, 82.03%, and 79.56% compared to Hirs model, Ng–Pan model, and Constantinescu model, respectively, and the calculation time reduces by 92.56% compared to Elrod–Ng model. The corrected turbulence coefficient is further verified by the performance calculation of ATB-SCO2 at eight working conditions.
- 1 September 2026
- Published by AIP Publishing in Physics of Fluids
- Vol. 38 (9)
Effect and correction of turbulence coefficient on performance calculation of aerostatic thrust bearing lubricated by supercritical CO2
In this article, the flow field and bearing performance of aerostatic thrust bearing (ATB) lubricated by supercritical CO2 (ATB-SCO2) are analyzed by solving the Reynolds equation with the laminar model and four turbulence models (Hirs model, Ng–Pan model, Constantinescu model, and Elrod–Ng model) through the finite difference method. The calculation accuracy and efficiency of ATB-SCO2 performance under different flow and CO2 models are discussed. Furthermore, the turbulence coefficient is corrected by analyzing the influences of empirical coefficient and empirical exponent on the calculation results of ATB-SCO2 performance. The turbulence models with turbulence coefficients increase the pressure and Reynolds number but decrease the velocity in the lubricating film. The ideal gas assumption shows the same effect (i.e., an increase) on pressure but opposite effects (i.e., an increase) on Reynolds number and velocity. Moreover, both turbulence models with turbulence coefficients and ideal gas assumption increase the bearing load capacity and stiffness but reduce the mass flow rate. Compared to Elrod–Ng model, the calculation adopting laminar model, Hirs model, Ng–Pan model, and Constantinescu model are less accurate but more efficient. The accuracy using the model with corrected turbulence coefficient improves by 86.02%, 82.03%, and 79.56% compared to Hirs model, Ng–Pan model, and Constantinescu model, respectively, and the calculation time reduces by 92.56% compared to Elrod–Ng model. The corrected turbulence coefficient is further verified by the performance calculation of ATB-SCO2 at eight working conditions.
- 4 May 2026
- Published by SAGE Publications in Proceedings of the Institution of Mechanical Engineers, Part I: Journal of Systems and Control Engineering
- Vol. 240 (6) , 956-968
Integrated on-line recognition and control for adaptive hysteresis compensation in pneumatic muscle actuators
Pneumatic Muscle Actuators (PMAs) present a persistent challenge in high-precision motion control due to their pronounced hysteresis nonlinearity. While conventional Proportional-Integral-Derivative (PID) controllers based on offline-identified hysteresis models are widely used, they fail to capture the time-varying and load-dependent nature of PMA hysteresis, leading to significant modeling and tracking errors. To overcome this limitation, this paper introduces a novel integrated control architecture that, for the first time, tightly couples real-time hysteresis identification with adaptive PID regulation. The proposed method retains the simplicity of the classical Prandtl–Ishlinskii (PI) hysteresis model but employs an online parameter estimator-specifically the Forgetting-Factor Recursive Least Squares (FFRLS) algorithm—to continuously update the model under varying loads and frequencies. Furthermore, three distinct adaptive PID controllers are developed and experimentally compared, whose gains are adjusted online via a Back-Propagation (BP) neural network, a Radial Basis Function (RBF) neural network, or a fuzzy-logic system. Extensive trajectory-tracking tests demonstrate that: the FFRLS-based online identification effectively adapts to load changes and achieves the highest modeling accuracy among the tested online methods; all three adaptive PID variants significantly outperform the conventional PID controller; the BP-based adaptive PID controller delivers the best overall performance-requiring no manual tuning, exhibiting superior robustness against both load and frequency disturbances, and reducing tracking error by more than 40% compared to the classical PID approach. Thus, this work establishes a practical, readily implementable control solution that exploits the synergy between online hysteresis compensation and adaptive PID tuning, offering a robust framework for precision motion control of PMA-driven systems in real-world applications.
- 4 May 2026
- Published by SAGE Publications in Proceedings of the Institution of Mechanical Engineers, Part I: Journal of Systems and Control Engineering
- Vol. 240 (6) , 956-968
Integrated on-line recognition and control for adaptive hysteresis compensation in pneumatic muscle actuators
Pneumatic Muscle Actuators (PMAs) present a persistent challenge in high-precision motion control due to their pronounced hysteresis nonlinearity. While conventional Proportional-Integral-Derivative (PID) controllers based on offline-identified hysteresis models are widely used, they fail to capture the time-varying and load-dependent nature of PMA hysteresis, leading to significant modeling and tracking errors. To overcome this limitation, this paper introduces a novel integrated control architecture that, for the first time, tightly couples real-time hysteresis identification with adaptive PID regulation. The proposed method retains the simplicity of the classical Prandtl–Ishlinskii (PI) hysteresis model but employs an online parameter estimator-specifically the Forgetting-Factor Recursive Least Squares (FFRLS) algorithm—to continuously update the model under varying loads and frequencies. Furthermore, three distinct adaptive PID controllers are developed and experimentally compared, whose gains are adjusted online via a Back-Propagation (BP) neural network, a Radial Basis Function (RBF) neural network, or a fuzzy-logic system. Extensive trajectory-tracking tests demonstrate that: the FFRLS-based online identification effectively adapts to load changes and achieves the highest modeling accuracy among the tested online methods; all three adaptive PID variants significantly outperform the conventional PID controller; the BP-based adaptive PID controller delivers the best overall performance-requiring no manual tuning, exhibiting superior robustness against both load and frequency disturbances, and reducing tracking error by more than 40% compared to the classical PID approach. Thus, this work establishes a practical, readily implementable control solution that exploits the synergy between online hysteresis compensation and adaptive PID tuning, offering a robust framework for precision motion control of PMA-driven systems in real-world applications.
- Open Access
- 9 March 2026
- Published by Walter de Gruyter GmbH in International Journal of Turbo & Jet-Engines
- Vol. 43 (3) , 561-572
Research on multi-parameter optimization methods of the performance for a micro pneumatic turbine
In this article, response surface method (RSM), RSM combined with seeker optimization algorithm (RSM-SOA) and RSM combined with differential evolution seeker optimization algorithm (RSM-DE-SOA) are adopted for the performance optimization of a micro pneumatic turbine, avoiding the limitation of being prone to local optima of control variable method, RSM and factorial method. The nonlinear combinations of structure parameters affecting rotation speed of a pneumatic turbine are obtained by using Minitab. Furthermore, a sample comprising turbine structure parameters and corresponding rotation speed calculated by actual conditions driving simulation (ACDS) is established. The structure parameters are optimized by using RSM with rotation speed as optimization objective and further optimized through RSM-SOA and RSM-DE-SOA. The results demonstrate that RSM-DE-SOA obtains the best outcome. The turbine attains global optimal rotation speed of 171.2 krpm with an output power of 106.7 W when nozzle diameter, turbine diameter and blade tip clearance are 1.9 mm, 15.0 mm and 0.45 mm, respectively.
- 9 March 2026
- Published by Walter de Gruyter GmbH in International Journal of Turbo & Jet-Engines
- Vol. 43 (3) , 561-572
Open AccessResearch on multi-parameter optimization methods of the performance for a micro pneumatic turbine
In this article, response surface method (RSM), RSM combined with seeker optimization algorithm (RSM-SOA) and RSM combined with differential evolution seeker optimization algorithm (RSM-DE-SOA) are adopted for the performance optimization of a micro pneumatic turbine, avoiding the limitation of being prone to local optima of control variable method, RSM and factorial method. The nonlinear combinations of structure parameters affecting rotation speed of a pneumatic turbine are obtained by using Minitab. Furthermore, a sample comprising turbine structure parameters and corresponding rotation speed calculated by actual conditions driving simulation (ACDS) is established. The structure parameters are optimized by using RSM with rotation speed as optimization objective and further optimized through RSM-SOA and RSM-DE-SOA. The results demonstrate that RSM-DE-SOA obtains the best outcome. The turbine attains global optimal rotation speed of 171.2 krpm with an output power of 106.7 W when nozzle diameter, turbine diameter and blade tip clearance are 1.9 mm, 15.0 mm and 0.45 mm, respectively.
- 3 December 2025
- Published by SAGE Publications in Proceedings of the Institution of Mechanical Engineers, Part J: Journal of Engineering Tribology
- Vol. 240 (8) , 1425-1436
Mixed TEHL analysis of tandem hydraulic reciprocating seal in deep-sea hydraulic system considering inter-cavity pressure effect
Connecting two or more seals in series is an effective way to improve the reliability of seals for deep-sea hydraulic systems, but the pressure fluctuations in the inter-cavity between the two-stage seals may have adverse effects on the sealing system. To address it, this paper established a mixed thermo-elastohydrodynamic lubrication (TEHL) model for tandem hydraulic reciprocating seal (HRS) applied in deep-sea hydraulic system. The service state of the seal is defined according to the evolution law of inter-cavity pressure, and the impact of operating conditions on the sealing behavior and performance of the seal under different service status is explored. The research results indicate that tandem seals have a significant advantage over single seals to reduce leakage, but also lead to increased friction in the sealing system. As the inter-cavity pressure increases, the components in the sealing system that mainly perform sealing function gradually change from the main-seal to the sub-seal. It is recommended to reduce the damage to the function of the tandem seal by increasing the volume of the inter-cavity or regularly releasing the inter-cavity pressure, thereby further improving the reliability of the tandem seal in deep-sea hydraulic system.
- 3 December 2025
- Published by SAGE Publications in Proceedings of the Institution of Mechanical Engineers, Part J: Journal of Engineering Tribology
- Vol. 240 (8) , 1425-1436
Mixed TEHL analysis of tandem hydraulic reciprocating seal in deep-sea hydraulic system considering inter-cavity pressure effect
Connecting two or more seals in series is an effective way to improve the reliability of seals for deep-sea hydraulic systems, but the pressure fluctuations in the inter-cavity between the two-stage seals may have adverse effects on the sealing system. To address it, this paper established a mixed thermo-elastohydrodynamic lubrication (TEHL) model for tandem hydraulic reciprocating seal (HRS) applied in deep-sea hydraulic system. The service state of the seal is defined according to the evolution law of inter-cavity pressure, and the impact of operating conditions on the sealing behavior and performance of the seal under different service status is explored. The research results indicate that tandem seals have a significant advantage over single seals to reduce leakage, but also lead to increased friction in the sealing system. As the inter-cavity pressure increases, the components in the sealing system that mainly perform sealing function gradually change from the main-seal to the sub-seal. It is recommended to reduce the damage to the function of the tandem seal by increasing the volume of the inter-cavity or regularly releasing the inter-cavity pressure, thereby further improving the reliability of the tandem seal in deep-sea hydraulic system.
- 1 December 2025
- Published by AIP Publishing in Physics of Fluids
- Vol. 37 (12)
A novel micro-vibration prediction method for an aerostatic thrust bearing by using Ω-vortex identification
In this paper, an Ω-vortex identification method is proposed to predict the micro-vibration of an aerostatic thrust bearing. It can identify vortex structure and corresponding spatial distribution in bearing gas film accurately, quantifying vortex region area by the Ω iso-surface. Four methods are used to predict the micro-vibration of nine aerostatic thrust bearings according to the flow fields obtained by large eddy simulation (LES). The experimental results indicate that the prediction accuracy is 66.7% for the maximum gas flow velocity method, 83.3% for the maximum gas pressure difference method and gas pressure fluctuation method, and 100% for the Ω-vortex identification method. The proposed method is helpful for micro-vibration prediction and provides guidance for structure optimization to suppress vortex and micro-vibration of an aerostatic thrust bearing.
- 1 December 2025
- Published by AIP Publishing in Physics of Fluids
- Vol. 37 (12)
A novel micro-vibration prediction method for an aerostatic thrust bearing by using Ω-vortex identification
In this paper, an Ω-vortex identification method is proposed to predict the micro-vibration of an aerostatic thrust bearing. It can identify vortex structure and corresponding spatial distribution in bearing gas film accurately, quantifying vortex region area by the Ω iso-surface. Four methods are used to predict the micro-vibration of nine aerostatic thrust bearings according to the flow fields obtained by large eddy simulation (LES). The experimental results indicate that the prediction accuracy is 66.7% for the maximum gas flow velocity method, 83.3% for the maximum gas pressure difference method and gas pressure fluctuation method, and 100% for the Ω-vortex identification method. The proposed method is helpful for micro-vibration prediction and provides guidance for structure optimization to suppress vortex and micro-vibration of an aerostatic thrust bearing.
- 1 December 2025
- Published by AIP Publishing in Physics of Fluids
- Vol. 37 (12)
Performance analysis of high-speed aerostatic thrust bearing lubricated by high-pressure natural gas adopting the Elrod-Ng turbulent model
An aerostatic thrust bearing lubricated by natural gas (ATB-NG) is an ideal supporting component for a natural gas turbo-expander. However, complex turbulent flow exists in the gas film if the ATB-NG operates at high-pressure and high-speed conditions, leading to prediction errors in bearing performance by using a laminar model. This article establishes a modified Reynolds equation adopting the Elrod-Ng turbulent model to calculate the performance of an aerostatic thrust bearing (ATB). The result demonstrates that the gas flow state experiences laminar flow, transitional flow, and turbulent flow sequentially with the increase in rotation speed, causing ATB performance calculated by the turbulent model to deviate from that of the laminar model. Moreover, the critical rotation speed, at which gas flow state transitions from transitional flow to turbulent flow, is related to the ratio of gas density to viscosity. Compared with the result calculated by laminar model, the load capacity, mass flow rate, and stiffness calculated by turbulent model increases by 5.4%–88.1%, decreases by 1.6%–24.3%, and grows by 4.5%–69.9%, respectively, while the operating condition changes (operating pressure: 2–4.2 MPa, operating temperature: 280–335 K, and bearing clearance: 8–30 μm). Furthermore, the performance of the ATB-NG is poorer than that of an aerostatic thrust bearing lubricated by air (ATB-AIR) at different working conditions.
- 1 December 2025
- Published by AIP Publishing in Physics of Fluids
- Vol. 37 (12)
Performance analysis of high-speed aerostatic thrust bearing lubricated by high-pressure natural gas adopting the Elrod-Ng turbulent model
An aerostatic thrust bearing lubricated by natural gas (ATB-NG) is an ideal supporting component for a natural gas turbo-expander. However, complex turbulent flow exists in the gas film if the ATB-NG operates at high-pressure and high-speed conditions, leading to prediction errors in bearing performance by using a laminar model. This article establishes a modified Reynolds equation adopting the Elrod-Ng turbulent model to calculate the performance of an aerostatic thrust bearing (ATB). The result demonstrates that the gas flow state experiences laminar flow, transitional flow, and turbulent flow sequentially with the increase in rotation speed, causing ATB performance calculated by the turbulent model to deviate from that of the laminar model. Moreover, the critical rotation speed, at which gas flow state transitions from transitional flow to turbulent flow, is related to the ratio of gas density to viscosity. Compared with the result calculated by laminar model, the load capacity, mass flow rate, and stiffness calculated by turbulent model increases by 5.4%–88.1%, decreases by 1.6%–24.3%, and grows by 4.5%–69.9%, respectively, while the operating condition changes (operating pressure: 2–4.2 MPa, operating temperature: 280–335 K, and bearing clearance: 8–30 μm). Furthermore, the performance of the ATB-NG is poorer than that of an aerostatic thrust bearing lubricated by air (ATB-AIR) at different working conditions.
- 1 November 2025
- Published by AIP Publishing in Physics of Fluids
- Vol. 37 (11)
Theoretical and experimental studies on the effect of spiral groove–orifice restrictor position coupling on the performance of hybrid aerostatic–aerodynamic thrust bearing
To meet the requirements of high-speed and high-power rotational equipment for gas thrust bearings with large load bearing capacity and high stiffness, this study takes the spiral groove–orifice restrictor coupled hybrid aerostatic–aerodynamic thrust bearing (HATB) as the research object. Using computational fluid dynamics numerical simulation and performance experiments, this study investigates the influence of the relative position between the spiral groove and the orifice restrictor on gas flow characteristics, load bearing capacity, and stiffness of the HATB. Furthermore, the effects of gas supply pressure and rotational speed on the coupling interaction between the spiral groove and the orifice restrictor are analyzed. The results reveal that the orifice restrictor dominates the gas pressure distribution within the gas film of the bearing, while the spiral groove alters the gas pressure distribution at its location and adjusts the gas pressure distribution in adjacent regions. The coupling interaction between the spiral groove and the orifice restrictor exhibits significant dependence on the rotational speed of the thrust surface. Under stationary conditions or low rotational speeds, close proximity between the spiral groove and the orifice restrictor results in synergistic static performance enhancement. As the spacing increases, the coupling effect between the spiral groove and the orifice restrictor shifts from synergistically enhancing bearing performance to synergistically suppressing it. When the rotational speed exceeds a certain critical value, spiral groove and orifice restrictor could synergistically enhance the load bearing capacity and stiffness of gas bearing. Experimental findings demonstrate that under stationary conditions and large gas film thickness, the experiment load bearing capacity and experiment stiffness of HATB A1, HATB A2, and HATB A3 surpass those of orifice-throttled aerostatic thrust bearing. This study highlights that an optimized design of the relative position between the spiral groove and the orifice restrictor can improve both the load bearing capacity and stiffness of the HATB, offering valuable insight for the design of high-performance gas thrust bearings in precision applications.
- 1 November 2025
- Published by AIP Publishing in Physics of Fluids
- Vol. 37 (11)
Theoretical and experimental studies on the effect of spiral groove–orifice restrictor position coupling on the performance of hybrid aerostatic–aerodynamic thrust bearing
To meet the requirements of high-speed and high-power rotational equipment for gas thrust bearings with large load bearing capacity and high stiffness, this study takes the spiral groove–orifice restrictor coupled hybrid aerostatic–aerodynamic thrust bearing (HATB) as the research object. Using computational fluid dynamics numerical simulation and performance experiments, this study investigates the influence of the relative position between the spiral groove and the orifice restrictor on gas flow characteristics, load bearing capacity, and stiffness of the HATB. Furthermore, the effects of gas supply pressure and rotational speed on the coupling interaction between the spiral groove and the orifice restrictor are analyzed. The results reveal that the orifice restrictor dominates the gas pressure distribution within the gas film of the bearing, while the spiral groove alters the gas pressure distribution at its location and adjusts the gas pressure distribution in adjacent regions. The coupling interaction between the spiral groove and the orifice restrictor exhibits significant dependence on the rotational speed of the thrust surface. Under stationary conditions or low rotational speeds, close proximity between the spiral groove and the orifice restrictor results in synergistic static performance enhancement. As the spacing increases, the coupling effect between the spiral groove and the orifice restrictor shifts from synergistically enhancing bearing performance to synergistically suppressing it. When the rotational speed exceeds a certain critical value, spiral groove and orifice restrictor could synergistically enhance the load bearing capacity and stiffness of gas bearing. Experimental findings demonstrate that under stationary conditions and large gas film thickness, the experiment load bearing capacity and experiment stiffness of HATB A1, HATB A2, and HATB A3 surpass those of orifice-throttled aerostatic thrust bearing. This study highlights that an optimized design of the relative position between the spiral groove and the orifice restrictor can improve both the load bearing capacity and stiffness of the HATB, offering valuable insight for the design of high-performance gas thrust bearings in precision applications.
- 1 October 2025
- Published by AIP Publishing in Physics of Fluids
- Vol. 37 (10)
Influence of inlet and outlet shift on the performance of a micro pneumatic turbine
This article proposes micro pneumatic turbines with shift inlet and outlet. The rotation speeds and output powers of the micro pneumatic turbines with four inlet and outlet layouts [radial inlet and radial outlet (RIRO); inlet and outlet both circumferential shift (IOBS); radial inlet and axial outlet (RIAO); inlet circumferential shift and axial outlet (ISAO)] are calculated by using actual conditions driving simulation. Moreover, the influence of inlet and outlet layout on turbine performance is analyzed according to flow characteristics and the Ω-vortex identification criterion. Furthermore, the maximum rotation speed and corresponding structure parameters and output power of the micro pneumatic turbine with the optimal inlet and outlet layout are obtained by using quadratic regression equations. Finally, the effects of inlet and outlet angles on the performance of the turbine with the optimal inlet and outlet layout are studied. The results indicate that the turbine with an IOBS layout can effectively alleviate abrupt pressure changes near the blade, reducing the occurrence of vortices and flow separation, and exhibiting the best performance. The maximum rotation speed of the IOBS turbine reaches to 356.43 krpm, and the corresponding output power is 253.68 W when the turbine diameter, blade height and tip clearance are 12.5, 2.6, and 1 mm, respectively. The influence of inlet angle on IOBS turbine performance is significant, whereas that of outlet angle is small.
- 1 October 2025
- Published by AIP Publishing in Physics of Fluids
- Vol. 37 (10)
Influence of inlet and outlet shift on the performance of a micro pneumatic turbine
This article proposes micro pneumatic turbines with shift inlet and outlet. The rotation speeds and output powers of the micro pneumatic turbines with four inlet and outlet layouts [radial inlet and radial outlet (RIRO); inlet and outlet both circumferential shift (IOBS); radial inlet and axial outlet (RIAO); inlet circumferential shift and axial outlet (ISAO)] are calculated by using actual conditions driving simulation. Moreover, the influence of inlet and outlet layout on turbine performance is analyzed according to flow characteristics and the Ω-vortex identification criterion. Furthermore, the maximum rotation speed and corresponding structure parameters and output power of the micro pneumatic turbine with the optimal inlet and outlet layout are obtained by using quadratic regression equations. Finally, the effects of inlet and outlet angles on the performance of the turbine with the optimal inlet and outlet layout are studied. The results indicate that the turbine with an IOBS layout can effectively alleviate abrupt pressure changes near the blade, reducing the occurrence of vortices and flow separation, and exhibiting the best performance. The maximum rotation speed of the IOBS turbine reaches to 356.43 krpm, and the corresponding output power is 253.68 W when the turbine diameter, blade height and tip clearance are 12.5, 2.6, and 1 mm, respectively. The influence of inlet angle on IOBS turbine performance is significant, whereas that of outlet angle is small.
- 1 September 2025
- Published by AIP Publishing in Physics of Fluids
- Vol. 37 (9)
A novel flow field analysis and performance prediction method for turbo-expanders under actual driving conditions
In this paper, actual conditions driving simulation (ACDS) is adopted for the flow field analysis and performance prediction of a turbo-expander. Compared to moving reference frames simulation (single reference frame simulation, SRFS and multiple reference frames simulation, MRFS) suffering from over-constrained boundary conditions, the settings of ACDS are consistent with actual working conditions. Moreover, the influences of a tetrahedral grid, a polyhedral grid, a hexahedral grid, and a poly-hexcore hybrid grid (PHHG) on the calculation results of SRFS, MRFS, and ACDS are analyzed for selecting the optimal grid of the simulations, considering calculation efficiency and accuracy. The results indicate that PHHG is the best grid for SRFS and MRFS, while HG is the optimal choice for ACDS. The flow fields calculated by SRFS and MRFS exist unreasonable sudden change, while those of ACDS vary smoothly. The average errors of isentropic efficiency obtained from SRFS, MRFS, and ACDS are 11.84%, 4.18%, and 2.26%, respectively. Furthermore, the average error of rotation speed calculated by ACDS is 6.52%, and the dynamic variation process of rotation speed is obtained.
- 1 September 2025
- Published by AIP Publishing in Physics of Fluids
- Vol. 37 (9)
A novel flow field analysis and performance prediction method for turbo-expanders under actual driving conditions
In this paper, actual conditions driving simulation (ACDS) is adopted for the flow field analysis and performance prediction of a turbo-expander. Compared to moving reference frames simulation (single reference frame simulation, SRFS and multiple reference frames simulation, MRFS) suffering from over-constrained boundary conditions, the settings of ACDS are consistent with actual working conditions. Moreover, the influences of a tetrahedral grid, a polyhedral grid, a hexahedral grid, and a poly-hexcore hybrid grid (PHHG) on the calculation results of SRFS, MRFS, and ACDS are analyzed for selecting the optimal grid of the simulations, considering calculation efficiency and accuracy. The results indicate that PHHG is the best grid for SRFS and MRFS, while HG is the optimal choice for ACDS. The flow fields calculated by SRFS and MRFS exist unreasonable sudden change, while those of ACDS vary smoothly. The average errors of isentropic efficiency obtained from SRFS, MRFS, and ACDS are 11.84%, 4.18%, and 2.26%, respectively. Furthermore, the average error of rotation speed calculated by ACDS is 6.52%, and the dynamic variation process of rotation speed is obtained.
- 1 August 2025
- Published by AIP Publishing in Physics of Fluids
- Vol. 37 (8)
Influence of pressure fluctuations on the sealing performance of a spiral groove mechanical seal in different phase states
To investigate the impact of internal pressure fluctuations on the performance of multiphase flow mechanical seals in high-speed rotating equipment, this study focuses on a spiral groove mechanical seal and establishes a transient continuous boiling model that comprehensively considers centrifugal inertia and phase transition. The transient Reynolds equation, energy equation, and heat transfer equation are solved using the finite difference method, and the small perturbation method is employed to analyze multi-variable perturbations of film pressure, viscosity, and density. The study examines the influence of pressure fluctuations at the inner and outer diameters on the phase state of the fluid film and the steady-state and dynamic performance of the seal when the fluid film is in different phase states. The results indicate that the location of pressure fluctuations significantly affects the phase transition ratio of the fluid film and the sealing performance. Compared to inner diameter pressure fluctuations, outer diameter pressure fluctuations exhibit a more pronounced effect on the response curves of fluid film phase transition ratio, opening force, and axial stiffness coefficient, while showing a weaker influence on leakage rate and axial damping coefficient. When outer diameter pressure fluctuations stabilize, the restored stable response times of sealing performance and dynamic characteristic coefficients are significantly longer than those for inner diameter pressure fluctuations. Large-scale and rapid changes in the vapor mass fraction of the fluid film can significantly alter the pressure distribution, causing strong oscillations in the response curves of sealing performance and dynamic characteristic coefficients, and transient increases in leakage rate.
- 1 August 2025
- Published by AIP Publishing in Physics of Fluids
- Vol. 37 (8)
Influence of pressure fluctuations on the sealing performance of a spiral groove mechanical seal in different phase states
To investigate the impact of internal pressure fluctuations on the performance of multiphase flow mechanical seals in high-speed rotating equipment, this study focuses on a spiral groove mechanical seal and establishes a transient continuous boiling model that comprehensively considers centrifugal inertia and phase transition. The transient Reynolds equation, energy equation, and heat transfer equation are solved using the finite difference method, and the small perturbation method is employed to analyze multi-variable perturbations of film pressure, viscosity, and density. The study examines the influence of pressure fluctuations at the inner and outer diameters on the phase state of the fluid film and the steady-state and dynamic performance of the seal when the fluid film is in different phase states. The results indicate that the location of pressure fluctuations significantly affects the phase transition ratio of the fluid film and the sealing performance. Compared to inner diameter pressure fluctuations, outer diameter pressure fluctuations exhibit a more pronounced effect on the response curves of fluid film phase transition ratio, opening force, and axial stiffness coefficient, while showing a weaker influence on leakage rate and axial damping coefficient. When outer diameter pressure fluctuations stabilize, the restored stable response times of sealing performance and dynamic characteristic coefficients are significantly longer than those for inner diameter pressure fluctuations. Large-scale and rapid changes in the vapor mass fraction of the fluid film can significantly alter the pressure distribution, causing strong oscillations in the response curves of sealing performance and dynamic characteristic coefficients, and transient increases in leakage rate.