Hamed S. Askar
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Hamed S. Askar has a total of 7 co-authors. Here are the top co-authors by number of shared publications:
- Abdelrazek E. Ebrahim1 shared publication
El-Zoughiby M. El-Said
Associate Professor, Structural Engineering Department, Faculty of Engineering, Mansoura University, Mansoura 35516, Egypt
1 shared publication- Fatma A. Ebrahim
Department of Mathematics, Al-Azhar University, Cairo, Egypt
1 shared publication - Mashhour A. Ghoneim1 shared publication
Mohamed H. Mathana
Associate Professor, Structural Engineering Department, Faculty of Engineering, Mansoura University, Mansoura 35516, Egypt
1 shared publication- Omar M. Elmeligy
Concordia University
1 shared publication
Latest Publications
- 30 June 2021
- Published by Golden Light Publishing in Journal of Structural Engineering & Applied Mechanics
- Vol. 4 (2) , 111-125
Refined strength prediction of concrete 2D bottle-shaped struts
For better strength prediction using strut-and-tie models (STM), it is essential to use reliable strength parameters of the model components; e.g., struts, ties, and nodes. Among all the elements of the STM, the strength of the bottle-shaped struts is not well quantified. The purpose of this study is to develop more accurate formulas for the calculation of the effectiveness factors for 2D bottle-shaped struts, that are unreinforced, reinforced with minimum reinforcement, and reinforced with sufficient transverse reinforcement. The nonlinear finite element analysis, with the aid of the software ABAQUS, has been utilized in this study, which has been verified against experimental tests. The study has been carried out for grades of concrete varying from 20 to 100MPa, and for bearing plate to width ratio varying from 0.1 to 0.9. The obtained formulas for the effectiveness factors of bottle-shaped struts are functions of the concrete strength, which is not the case with the ACI 318-19 provisions. These formulas have been verified against experimental tests and have been compared with the ACI 318-19 provisions. The predictions based on these formulas are more accurate than those based on the ACI 318-19 provisions. Also, the results from these formulas are always on the safe side. On the other hand, the ACI 318-19 provisions lead to unsafe results in the case of high-strength concrete and very conservative results for the case of unreinforced struts from normal-strength concrete.
- 30 June 2021
- Published by Golden Light Publishing in Journal of Structural Engineering & Applied Mechanics
- Vol. 4 (2) , 111-125
Refined strength prediction of concrete 2D bottle-shaped struts
For better strength prediction using strut-and-tie models (STM), it is essential to use reliable strength parameters of the model components; e.g., struts, ties, and nodes. Among all the elements of the STM, the strength of the bottle-shaped struts is not well quantified. The purpose of this study is to develop more accurate formulas for the calculation of the effectiveness factors for 2D bottle-shaped struts, that are unreinforced, reinforced with minimum reinforcement, and reinforced with sufficient transverse reinforcement. The nonlinear finite element analysis, with the aid of the software ABAQUS, has been utilized in this study, which has been verified against experimental tests. The study has been carried out for grades of concrete varying from 20 to 100MPa, and for bearing plate to width ratio varying from 0.1 to 0.9. The obtained formulas for the effectiveness factors of bottle-shaped struts are functions of the concrete strength, which is not the case with the ACI 318-19 provisions. These formulas have been verified against experimental tests and have been compared with the ACI 318-19 provisions. The predictions based on these formulas are more accurate than those based on the ACI 318-19 provisions. Also, the results from these formulas are always on the safe side. On the other hand, the ACI 318-19 provisions lead to unsafe results in the case of high-strength concrete and very conservative results for the case of unreinforced struts from normal-strength concrete.
- Open Access
- 1 June 2019
- Published by Egyptian Knowledge Bank in Engineering Research Journal
- Vol. 162, 15-31
Punching Shear Behavior of Interior Slab-Column Connections Reinforced with Vertical Bolts
Punching shear failure in flat plate slabs is considered as a vital topic to investigate. The fact that this failure is brittle makes it an essential field to study. Many researches have been carried out to investigate the punching shear of flat plate slabs. Nevertheless, using prestressing in enhancing punching behavior wasn't of such a big contribution. An experimental study for enhancing punching shear volume of interior slab-column links in flat plate slabs by prestressing is presented through a parametric study in this research. The parameters taken into consideration in this study are prestressed vertical studs of different number of rows. Through the experimental program, deformation features, the load carrying capacity, and the cracking patterns have been examined. A comparative study between the behavior of the improved slabs and their controls has been made. This study showed that the suggested system might be of a good benefit in practice to be used. A comparison between the experimental punching load and the calculated using various design codes has also been made. It offered acceptable agreement.
- 1 June 2019
- Published by Egyptian Knowledge Bank in Engineering Research Journal
- Vol. 162, 15-31
Open AccessPunching Shear Behavior of Interior Slab-Column Connections Reinforced with Vertical Bolts
Punching shear failure in flat plate slabs is considered as a vital topic to investigate. The fact that this failure is brittle makes it an essential field to study. Many researches have been carried out to investigate the punching shear of flat plate slabs. Nevertheless, using prestressing in enhancing punching behavior wasn't of such a big contribution. An experimental study for enhancing punching shear volume of interior slab-column links in flat plate slabs by prestressing is presented through a parametric study in this research. The parameters taken into consideration in this study are prestressed vertical studs of different number of rows. Through the experimental program, deformation features, the load carrying capacity, and the cracking patterns have been examined. A comparative study between the behavior of the improved slabs and their controls has been made. This study showed that the suggested system might be of a good benefit in practice to be used. A comparison between the experimental punching load and the calculated using various design codes has also been made. It offered acceptable agreement.
- Open Access
- 1 September 2015
- Published by Elsevier in Alexandria Engineering Journal
- Vol. 54 (3) , 509-518
Usage of prestressed vertical bolts for retrofitting flat slabs damaged due to punching shear
- 1 September 2015
- Published by Elsevier in Alexandria Engineering Journal
- Vol. 54 (3) , 509-518
Open AccessUsage of prestressed vertical bolts for retrofitting flat slabs damaged due to punching shear