Dongkeun Lee
Research Subjects
Dongkeun Lee has a total of 13 co-authors. Here are the top co-authors by number of shared publications:
- Lijuan Cheng
Department of Civil and Environmental Engineering, 3161 Ghausi Hall, University of California Davis, One Shields Avenue, Davis, CA 95616, USA
2 shared publications Woo-Young Lim
2 shared publicationsYoung-Chan You
2 shared publicationsAlex Hak-Chul Shin
1 shared publicationChang Sik Choi
Department of Architectural Engineering, Hanyang University, Seoul 133-791, Republic of Korea
1 shared publicationHyun-Ki Choi
Department of Fire and Disaster Prevention Engineering, Kyungnam University, Gyeongsangnam-do 631-701, Republic of Korea
1 shared publication
Latest Publications
- 20 January 2021
- Published by Taylor & Francis in International Journal of Pavement Engineering
- Vol. 23 (9) , 2922-2936
Flexural and compressive behaviours of sustainable AC/RC composite system with various supplementary materials
Although sustainable infrastructure is indispensable, there is almost no reported research on an asphalt concrete (AC) and rubberized concrete (RC) composite pavement. Furthermore, each study incorporating rubber mostly deployed one or two supplementary materials. Therefore, the performance of sustainable AC/RC pavements with various supplementary materials including zeolite, slag, fly ash, and steel fiber was comprehensively investigated in this study. 126 cylinders (150×300 mm) and 84 beams (150×150×530 mm) under 4-point bending were tested. Based on the results, AC/RC pavement indicated much higher compressive strength, flexural strength, stiffness, and energy absorption capacity than AC one. Although 25% of coarse aggregate was replaced with rubber, when 30% of cement was replaced with zeolite, fly ash, and slag (each 10%) and steel fibers (1% of the beam volume) were added, 83.7% of the flexural strength of AC/plain concrete (PC) beams was retained. With 25% replacement of coarse aggregate by rubber and use of zeolite and slag (each 15%), 87.4% of the compressive strength of AC/PC was retained. 25% rubber and 30% slag were found to be the optimum design for AC/RC pavement. Moreover, results from the proposed equations for predicting flexural and compressive strengths were in good agreement with the test ones.
- 20 January 2021
- Published by Taylor & Francis in International Journal of Pavement Engineering
- Vol. 23 (9) , 2922-2936
Flexural and compressive behaviours of sustainable AC/RC composite system with various supplementary materials
Although sustainable infrastructure is indispensable, there is almost no reported research on an asphalt concrete (AC) and rubberized concrete (RC) composite pavement. Furthermore, each study incorporating rubber mostly deployed one or two supplementary materials. Therefore, the performance of sustainable AC/RC pavements with various supplementary materials including zeolite, slag, fly ash, and steel fiber was comprehensively investigated in this study. 126 cylinders (150×300 mm) and 84 beams (150×150×530 mm) under 4-point bending were tested. Based on the results, AC/RC pavement indicated much higher compressive strength, flexural strength, stiffness, and energy absorption capacity than AC one. Although 25% of coarse aggregate was replaced with rubber, when 30% of cement was replaced with zeolite, fly ash, and slag (each 10%) and steel fibers (1% of the beam volume) were added, 83.7% of the flexural strength of AC/plain concrete (PC) beams was retained. With 25% replacement of coarse aggregate by rubber and use of zeolite and slag (each 15%), 87.4% of the compressive strength of AC/PC was retained. 25% rubber and 30% slag were found to be the optimum design for AC/RC pavement. Moreover, results from the proposed equations for predicting flexural and compressive strengths were in good agreement with the test ones.
- Open Access
- 20 October 2018
- Published by MDPI AG in Sustainability
- Vol. 10 (10) , 3797
Evaluation of Progressive Collapse Resistance of Steel Moment Frames Designed with Different Connection Details Using Energy-Based Approximate Analysis
This study evaluates the progressive collapse resistance performance of steel moment frames, individually designed with different connection details. Welded unreinforced flange-bolted web (WUF-B) and reduced beam section (RBS) connections are selected and applied to ordinary moment frames designed as per the Korean Building Code (KBC) 2016. The 3-D steel frame systems are modeled using reduced models of 1-D and 2-D elements for beams, columns, connections, and composite slabs. Comparisons between the analyzed results of the reduced models and the experimental results are presented to verify the applicability of the models. Nonlinear static analyses of two prototype buildings with different connection details are conducted using the reduced models, and an energy-based approximate analysis is used to account for the dynamic effects associated with sudden column loss. The assessment on the structures was based on structural robustness and sensitivity methods using the alternative path method suggested in General Services Administration (GSA) 2003, in which column removal scenarios were performed and the bearing capacity of the initial structure with an undamaged column was calculated under gravity loads. According to the analytical results, the two prototype buildings satisfied the chord rotation criterion of GSA 2003. These results were expected since the composite slabs designed to withstand more than 3.3 times the required capacity had a significant effect on the stiffness of the entire structure. The RBS connections were found to be 14% less sensitive to progressive collapse compared to the WUF-B ones.
- 20 October 2018
- Published by MDPI AG in Sustainability
- Vol. 10 (10) , 3797
Open AccessEvaluation of Progressive Collapse Resistance of Steel Moment Frames Designed with Different Connection Details Using Energy-Based Approximate Analysis
This study evaluates the progressive collapse resistance performance of steel moment frames, individually designed with different connection details. Welded unreinforced flange-bolted web (WUF-B) and reduced beam section (RBS) connections are selected and applied to ordinary moment frames designed as per the Korean Building Code (KBC) 2016. The 3-D steel frame systems are modeled using reduced models of 1-D and 2-D elements for beams, columns, connections, and composite slabs. Comparisons between the analyzed results of the reduced models and the experimental results are presented to verify the applicability of the models. Nonlinear static analyses of two prototype buildings with different connection details are conducted using the reduced models, and an energy-based approximate analysis is used to account for the dynamic effects associated with sudden column loss. The assessment on the structures was based on structural robustness and sensitivity methods using the alternative path method suggested in General Services Administration (GSA) 2003, in which column removal scenarios were performed and the bearing capacity of the initial structure with an undamaged column was calculated under gravity loads. According to the analytical results, the two prototype buildings satisfied the chord rotation criterion of GSA 2003. These results were expected since the composite slabs designed to withstand more than 3.3 times the required capacity had a significant effect on the stiffness of the entire structure. The RBS connections were found to be 14% less sensitive to progressive collapse compared to the WUF-B ones.
- 1 December 2017
- Published by Elsevier in Engineering Structures
- Vol. 153, 653-664
Cyclic loading tests on exposed column-base plate weak-axis connections of small-size steel structures
- 1 December 2017
- Published by Elsevier in Engineering Structures
- Vol. 153, 653-664
Cyclic loading tests on exposed column-base plate weak-axis connections of small-size steel structures
- 1 October 2017
- Published by Elsevier in Journal of Constructional Steel Research
- Vol. 137, 286-296
Exposed column-base plate strong-axis connections for small-size steel construction
- 1 October 2017
- Published by Elsevier in Journal of Constructional Steel Research
- Vol. 137, 286-296
Exposed column-base plate strong-axis connections for small-size steel construction
- 1 October 2016
- Published by Elsevier in Composite Structures
- Vol. 154, 256-268
Finite element study on the impact responses of concrete masonry unit walls strengthened with fiber-reinforced polymer composite materials
- 1 October 2016
- Published by Elsevier in Composite Structures
- Vol. 154, 256-268
Finite element study on the impact responses of concrete masonry unit walls strengthened with fiber-reinforced polymer composite materials
- Open Access
- 21 October 2015
- Published by Wiley in International Journal of Polymer Science
- Vol. 2015, 1-13
Shear Strength of Unreinforced Masonry Wall Retrofitted with Fiber Reinforced Polymer and Hybrid Sheet
Unreinforced masonry (URM) structures represent a significant portion of existing historical structures around the world. Recent earthquakes have shown the need for seismic retrofitting for URM structures. Various types of strengthening methods have been used for URM structures. In particular, a strengthening technique using externally bonded (EB) fiber reinforced polymer (FRP) composites has attracted engineers since EB FRP materials effectively enhance the shear strength of URM walls with negligible change to cross-sectional area and weight of the walls. Research has been extensively conducted to determine characteristics of URM walls strengthened with EB FRP materials. However, it is still difficult to determine an appropriate retrofitting level due to the complexity of mechanical behavior of strengthened URM walls. In this study, in-plane behavior under lateral loading was, therefore, investigated on a full-scale nonstrengthened URM wall and URM walls retrofitted with two different FRP materials: carbon (CFRP) and hybrid (HFRP) sheets. The test results indicated that both FRP composites were effective in increasing shear strength in comparison with the control specimen. However, better performance was obtained with HFRP compared to CFRP. In addition, an equation for estimating effective strain was proposed, and the theoretical results were in good agreement with the experimental ones.
- 21 October 2015
- Published by Wiley in International Journal of Polymer Science
- Vol. 2015, 1-13
Open AccessShear Strength of Unreinforced Masonry Wall Retrofitted with Fiber Reinforced Polymer and Hybrid Sheet
Unreinforced masonry (URM) structures represent a significant portion of existing historical structures around the world. Recent earthquakes have shown the need for seismic retrofitting for URM structures. Various types of strengthening methods have been used for URM structures. In particular, a strengthening technique using externally bonded (EB) fiber reinforced polymer (FRP) composites has attracted engineers since EB FRP materials effectively enhance the shear strength of URM walls with negligible change to cross-sectional area and weight of the walls. Research has been extensively conducted to determine characteristics of URM walls strengthened with EB FRP materials. However, it is still difficult to determine an appropriate retrofitting level due to the complexity of mechanical behavior of strengthened URM walls. In this study, in-plane behavior under lateral loading was, therefore, investigated on a full-scale nonstrengthened URM wall and URM walls retrofitted with two different FRP materials: carbon (CFRP) and hybrid (HFRP) sheets. The test results indicated that both FRP composites were effective in increasing shear strength in comparison with the control specimen. However, better performance was obtained with HFRP compared to CFRP. In addition, an equation for estimating effective strain was proposed, and the theoretical results were in good agreement with the experimental ones.
- 1 October 2013
- Published by Elsevier in Construction and Building Materials
- Vol. 47, 1512-1522
Bond of NSM systems in concrete strengthening – Examining design issues of strength, groove detailing and bond-dependent coefficient
- 1 October 2013
- Published by Elsevier in Construction and Building Materials
- Vol. 47, 1512-1522
Bond of NSM systems in concrete strengthening – Examining design issues of strength, groove detailing and bond-dependent coefficient
- 1 February 2013
- Published by American Society of Civil Engineers (ASCE) in Journal of Composites for Construction
- Vol. 17 (1) , 117-129
Bond Characteristics of Various NSM FRP Reinforcements in Concrete
The rehabilitation and strengthening technique using near-surface mounted (NSM) fiber-reinforced polymer (FRP) has proved to be a reliable alternative to the existing methods for deficient concrete structures. To effectively apply this method, bond characteristics at the interface need to be fully understood. This paper presents the results of the bond performance of a wide range of embedded FRP NSM reinforcements with various surface configurations, cross-sectional shapes, material types, adhesive types, and groove sizes. A total of 109 concrete specimens (with a dimension of 350×300×150 mm) were tested under direct pull-out loading configuration. It was found that both specimen sets using NSM bars treated with spirally wound and sand coating with indentation and groove displayed the best performance. Strip shape was more effective than round and square cross-sectional shapes. Higher bond strength was obtained by using carbon FRP than glass and adhesives with higher material bond strength. Incre...
- 1 February 2013
- Published by American Society of Civil Engineers (ASCE) in Journal of Composites for Construction
- Vol. 17 (1) , 117-129
Bond Characteristics of Various NSM FRP Reinforcements in Concrete
The rehabilitation and strengthening technique using near-surface mounted (NSM) fiber-reinforced polymer (FRP) has proved to be a reliable alternative to the existing methods for deficient concrete structures. To effectively apply this method, bond characteristics at the interface need to be fully understood. This paper presents the results of the bond performance of a wide range of embedded FRP NSM reinforcements with various surface configurations, cross-sectional shapes, material types, adhesive types, and groove sizes. A total of 109 concrete specimens (with a dimension of 350×300×150 mm) were tested under direct pull-out loading configuration. It was found that both specimen sets using NSM bars treated with spirally wound and sand coating with indentation and groove displayed the best performance. Strip shape was more effective than round and square cross-sectional shapes. Higher bond strength was obtained by using carbon FRP than glass and adhesives with higher material bond strength. Incre...
- 1 August 2011
- Published by American Society of Civil Engineers (ASCE) in Journal of Composites for Construction
- Vol. 15 (4) , 615-624
Assessing the Strengthening Effect of Various Near-Surface-Mounted FRP Reinforcements on Concrete Bridge Slab Overhangs
The near-surface-mounted (NSM) method has proved to be a reliable alternative to the existing externally bonded (EB) method for the repair and strengthening of concrete structures using fiber-reinforced polymer (FRP) composites. This technique is especially advantageous in bridge deck upgrades for larger barriers and slab overhang strengthening. This paper presents the results of a comparison of the flexural behavior of bridge slab overhangs strengthened in negative bending moment regions with various types of NSM reinforcement that differ in surface condition (e.g., textured and sand coated), cross-sectional shape (e.g., round and square), material type (carbon and glass), and prestressing effect. Eleven full-scale overhang specimens (1.524 m long in overhang and 0.914 m wide) were tested under a cantilever condition. Test results showed that the FRP NSM reinforcements were effective in increasing both yield and ultimate strength of predamaged slab overhangs. All surface treatments were more beneficial t...
- 1 August 2011
- Published by American Society of Civil Engineers (ASCE) in Journal of Composites for Construction
- Vol. 15 (4) , 615-624
Assessing the Strengthening Effect of Various Near-Surface-Mounted FRP Reinforcements on Concrete Bridge Slab Overhangs
The near-surface-mounted (NSM) method has proved to be a reliable alternative to the existing externally bonded (EB) method for the repair and strengthening of concrete structures using fiber-reinforced polymer (FRP) composites. This technique is especially advantageous in bridge deck upgrades for larger barriers and slab overhang strengthening. This paper presents the results of a comparison of the flexural behavior of bridge slab overhangs strengthened in negative bending moment regions with various types of NSM reinforcement that differ in surface condition (e.g., textured and sand coated), cross-sectional shape (e.g., round and square), material type (carbon and glass), and prestressing effect. Eleven full-scale overhang specimens (1.524 m long in overhang and 0.914 m wide) were tested under a cantilever condition. Test results showed that the FRP NSM reinforcements were effective in increasing both yield and ultimate strength of predamaged slab overhangs. All surface treatments were more beneficial t...