Blanka Skocilasova
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Blanka Skocilasova has a total of 15 co-authors. Here are the top co-authors by number of shared publications:
- Frantisek Klimenda
Faculty of mechanical engineering, University of Jan Evangelista Purkyně in Ústí nad Labem, Pasteurova 1, 400 96 Ústí nad Labem, Czech Republic
10 shared publications - Josef Soukup
Faculty of mechanical engineering, University of Jan Evangelista Purkyně in Ústí nad Labem, Pasteurova 1, 400 96 Ústí nad Labem, Czech Republic
7 shared publications - Jan Skočilas
Department of Process Engineering, Czech Technical University in Prague, 16600 Prague, Czech Republic
6 shared publications - Tereza Jarosova4 shared publications
Jan Skočilas
Czech Technical University in Prague, Faculty of Mechanical Engineering, Department of Process Engineering, Technická 4, 166 07 Praha 6, Czech Republic
2 shared publicationsJosef Soukup
University J. E. Purkyně in Ústí nad Labem, Faculty of Mechanical Engineering, Institute of Machinery and Energetics, Na Okraji 1001, 400 96 Ústí nad Labem, Czech Republic
2 shared publications
Latest Publications
- Open Access
- 17 November 2026
- Published by Jan Evangelista Purkyne University in Usti nad Labem in Manufacturing Technology
- Vol. 26 (4) , 408-423
Model solution for vibrations of mechanical systems - Part I
- 17 November 2026
- Published by Jan Evangelista Purkyne University in Usti nad Labem in Manufacturing Technology
- Vol. 26 (4) , 408-423
Open AccessModel solution for vibrations of mechanical systems - Part I
- Open Access
- 8 December 2025
- Published by Jan Evangelista Purkyne University in Usti nad Labem in Manufacturing Technology
- Vol. 25 (5) , 597-606
Elevator Vibrations and Ways to Reduce Them
The article deals with the measurement of the vibrations in passenger elevators. The introduction of an article briefly discusses machine vibrations and their impact on machine design and the surrounding environment. The basic equations from which the equations of motion are derived are listed here. The importance of analyzing machine vibrations in their design, or rather proposing solutions to reduce vibrations during machine reconstruction, is emphasized. Specifically, attention is paid to vibrations generated during an elevator operation in the elevator shaft. This is an elevator for transporting people in a newly constructed 5-story building. Vibration values generated by an elevator operation were measured in order to assess the suitability of simple anti-vibration modifications. Vibration measurements were taken on an existing elevator without modifications, and after the initial measurements, modifications were made to attach the guides to the bracket and attach the bracket to the elevator shaft wall. After the adjustment, the vibration measurement was performed again and both measurements were compared with each other.
- 8 December 2025
- Published by Jan Evangelista Purkyne University in Usti nad Labem in Manufacturing Technology
- Vol. 25 (5) , 597-606
Open AccessElevator Vibrations and Ways to Reduce Them
The article deals with the measurement of the vibrations in passenger elevators. The introduction of an article briefly discusses machine vibrations and their impact on machine design and the surrounding environment. The basic equations from which the equations of motion are derived are listed here. The importance of analyzing machine vibrations in their design, or rather proposing solutions to reduce vibrations during machine reconstruction, is emphasized. Specifically, attention is paid to vibrations generated during an elevator operation in the elevator shaft. This is an elevator for transporting people in a newly constructed 5-story building. Vibration values generated by an elevator operation were measured in order to assess the suitability of simple anti-vibration modifications. Vibration measurements were taken on an existing elevator without modifications, and after the initial measurements, modifications were made to attach the guides to the bracket and attach the bracket to the elevator shaft wall. After the adjustment, the vibration measurement was performed again and both measurements were compared with each other.
- Open Access
- 11 November 2025
- Published by Jan Evangelista Purkyne University in Usti nad Labem in Manufacturing Technology
- Vol. 25 (4) , 531-539
Analytic Solution of the Motion Equations of the Rolling Stock Chassis Incorporating the Effect of Asymmetry and Kinematics Excitation
The article provides an analytical solution for the dynamics of a vehicle chassis designed for both road and rail operation, featuring either single or multiple primary linear suspensions using coil springs. It derives the equations of motion ...
- 11 November 2025
- Published by Jan Evangelista Purkyne University in Usti nad Labem in Manufacturing Technology
- Vol. 25 (4) , 531-539
Open AccessAnalytic Solution of the Motion Equations of the Rolling Stock Chassis Incorporating the Effect of Asymmetry and Kinematics Excitation
The article provides an analytical solution for the dynamics of a vehicle chassis designed for both road and rail operation, featuring either single or multiple primary linear suspensions using coil springs. It derives the equations of motion ...
- Open Access
- 1 July 2024
- Published by Jan Evangelista Purkyne University in Usti nad Labem in Manufacturing Technology
- Vol. 24 (3) , 393-409
Deformation and Velocity Wave Propagation in a Thin Isotropic Plate
The propagation and velocity of the deformation wave in the thin isotropic plate is investigated. The deformation is induced by the stroke of impact body onto the facial surface of the plate. The plate is supported perpendicularly. The excitation of the plate oscillation is initialized by a unit force (Heaviside's jump). The impact body has a rounded facet by radius c = 2.5 mm. Hook's material model and Kirchhoff's and Flüegge's geometric model have been investigated. The analytical solutions for both models are presented. The MATLAB script has been assembled to solve material and geometrical models. The results were compared for two selected points on the surface of the plate. Plate deformation was recorded at two points T1 (at a distance of 20 mm from the impact location on the x axis) and T2 (at a distance of 20 mm from the impact location on the y axis).
- 1 July 2024
- Published by Jan Evangelista Purkyne University in Usti nad Labem in Manufacturing Technology
- Vol. 24 (3) , 393-409
Open AccessDeformation and Velocity Wave Propagation in a Thin Isotropic Plate
The propagation and velocity of the deformation wave in the thin isotropic plate is investigated. The deformation is induced by the stroke of impact body onto the facial surface of the plate. The plate is supported perpendicularly. The excitation of the plate oscillation is initialized by a unit force (Heaviside's jump). The impact body has a rounded facet by radius c = 2.5 mm. Hook's material model and Kirchhoff's and Flüegge's geometric model have been investigated. The analytical solutions for both models are presented. The MATLAB script has been assembled to solve material and geometrical models. The results were compared for two selected points on the surface of the plate. Plate deformation was recorded at two points T1 (at a distance of 20 mm from the impact location on the x axis) and T2 (at a distance of 20 mm from the impact location on the y axis).
- Open Access
Vertical Oscillation of Railway Vehicle Chassis with Asymmetry Effect Consideration
This paper deals with the problem of vertical oscillation of rail and road vehicles under symmetrical and asymmetrical loading and symmetrical and asymmetrical kinematic excitation. The term asymmetry is understood as the asymmetric distribution of vehicle mass and elastic and dissipative elements with respect to the axes of geometric symmetry, including asymmetric kinematic excitation. The various models used (spatial, planar, quarter-plane) are discussed and their analytical solutions are outlined. The theory of the spatial model is applied to the chassis of a model railway vehicle. The basic relations for the calculation of the equations of motion of this vehicle are given. In the next section, the experimental solution of a four-axle platform rail car is described and the measurements of vertical displacement and accelerations when crossing wedges (representing unevenness) are given.
Open AccessVertical Oscillation of Railway Vehicle Chassis with Asymmetry Effect Consideration
This paper deals with the problem of vertical oscillation of rail and road vehicles under symmetrical and asymmetrical loading and symmetrical and asymmetrical kinematic excitation. The term asymmetry is understood as the asymmetric distribution of vehicle mass and elastic and dissipative elements with respect to the axes of geometric symmetry, including asymmetric kinematic excitation. The various models used (spatial, planar, quarter-plane) are discussed and their analytical solutions are outlined. The theory of the spatial model is applied to the chassis of a model railway vehicle. The basic relations for the calculation of the equations of motion of this vehicle are given. In the next section, the experimental solution of a four-axle platform rail car is described and the measurements of vertical displacement and accelerations when crossing wedges (representing unevenness) are given.
- Open Access
- 18 September 2021
- Published by Jan Evangelista Purkyne University in Usti nad Labem in Manufacturing Technology
- Vol. 21 (4) , 471-478
Model solving of aluminium alloy solidification
- 18 September 2021
- Published by Jan Evangelista Purkyne University in Usti nad Labem in Manufacturing Technology
- Vol. 21 (4) , 471-478
Open AccessModel solving of aluminium alloy solidification
- 1 January 2021
- Published by Springer Nature
- p. 25-36
Convergence of Dual Infinity Series
- Open Access
- 15 January 2019
- Published by EDP Sciences in MATEC Web of Conferences
- Vol. 254, 03010
Vertical oscillation investigation of spatially elastically supported rigid plate – vehicle model
The article deals with introduction into the issue of the general asymmetry under vertical oscillation of systems of spatially elastically supported bodies with context of vehicle application. The various models are mentioned, quarter, half and full model (with different DOF) and advantages and disadvantages are discussed. The basic calculation procedures were presented for symmetry and asymmetry of geometry and excitation. The excitation is produced by jump change of plate support (analytically and numerically solved by Heaviside’s function, in the experimental part by jump down from the wedges). The procedure to solve the basic 3D model is introduced for selected types of asymmetry of geometry and excitation. The practical approach is presented on the two-axle railroad vehicle. The vertical displacement, velocities, accelerations and angles of rotation of symmetry axes are considered. The time trend of the vertical displacement of the general point the aim of the calculation (3 DOF considered).
- 15 January 2019
- Published by EDP Sciences in MATEC Web of Conferences
- Vol. 254, 03010
Open AccessVertical oscillation investigation of spatially elastically supported rigid plate – vehicle model
The article deals with introduction into the issue of the general asymmetry under vertical oscillation of systems of spatially elastically supported bodies with context of vehicle application. The various models are mentioned, quarter, half and full model (with different DOF) and advantages and disadvantages are discussed. The basic calculation procedures were presented for symmetry and asymmetry of geometry and excitation. The excitation is produced by jump change of plate support (analytically and numerically solved by Heaviside’s function, in the experimental part by jump down from the wedges). The procedure to solve the basic 3D model is introduced for selected types of asymmetry of geometry and excitation. The practical approach is presented on the two-axle railroad vehicle. The vertical displacement, velocities, accelerations and angles of rotation of symmetry axes are considered. The time trend of the vertical displacement of the general point the aim of the calculation (3 DOF considered).
- 7 August 2018
- Published by AIP Publishing in AIP Conference Proceedings
- Vol. 2000 (1) , 020016
Optimalization of steam control station
The article deals with the design of a new reduction station. The station serves for backup heating of the hot water heat exchangers. The hot water heating network of the Ledvice power plant is the main system. Back-up heating system has been developed with regard to the enhancement of the heat demand by 1.5 MWt. The existing fluid block and the new supercritical block equipped by granular boiler will be used as a new source of the heat. The main fuel of the boiler is brown coal. A new control station for a steam reduction (demanded for heating of a hot-water circuit) is described.
- 7 August 2018
- Published by AIP Publishing in AIP Conference Proceedings
- Vol. 2000 (1) , 020016
Optimalization of steam control station
The article deals with the design of a new reduction station. The station serves for backup heating of the hot water heat exchangers. The hot water heating network of the Ledvice power plant is the main system. Back-up heating system has been developed with regard to the enhancement of the heat demand by 1.5 MWt. The existing fluid block and the new supercritical block equipped by granular boiler will be used as a new source of the heat. The main fuel of the boiler is brown coal. A new control station for a steam reduction (demanded for heating of a hot-water circuit) is described.
- 7 August 2018
- Published by AIP Publishing in AIP Conference Proceedings
- Vol. 2000 (1) , 020017
Cooling of core during aluminum casting
The article deals with the casting process of the pistons for combustion engines. The molds are cooled to reduce the casting cycle time. The mold and cores are made of steel and cooled down by water. The complicated geometry of the casting tools and non-uniform cooling cause the inhomogeneous temperature distribution especially in the core. As a result, the internal stresses are generated in the core that cause it to crack and thus reduce its life cycle.
- 7 August 2018
- Published by AIP Publishing in AIP Conference Proceedings
- Vol. 2000 (1) , 020017
Cooling of core during aluminum casting
The article deals with the casting process of the pistons for combustion engines. The molds are cooled to reduce the casting cycle time. The mold and cores are made of steel and cooled down by water. The complicated geometry of the casting tools and non-uniform cooling cause the inhomogeneous temperature distribution especially in the core. As a result, the internal stresses are generated in the core that cause it to crack and thus reduce its life cycle.