Yuri G. Kabaldin
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Yuri G. Kabaldin has a total of 42 co-authors. Here are the top co-authors by number of shared publications:
- Maksim S. Anosov
R.E. Alekseev Nizhny Novgorod State Technical University
8 shared publications - Dmitrii A. Shatagin
Nizhny Novgorod State Technical University
5 shared publications - Dmitrii A. Ryabov
Nizhny Novgorod State Technical University, Nizhny Novgorod, Russia
4 shared publications Dmitry A. Ryabov
Nizhny Novgorod State Technical University
3 shared publications- Alexander A. Khlybov
Nizhny Novgorod State Technical University named after R.E. Alekseev, Nizhny Novgorod, Russia
2 shared publications Andrey V. Kiselev
Nizhny Novgorod State Technical University
2 shared publications
Latest Publications
- Open Access
- 2 July 2026
- Published by National University of Science and Technology MISiS in Izvestiya. Ferrous Metallurgy
- Vol. 69 (3) , 242-249
Effect of the defects occurring during WAAM process on fatigue strength of 08CrMoV and 30CrMnSi steels
At the moment, there are very few studies on fatigue failure of the products obtained by additive manufacturing, especially when fatigue failure occurs due to various types of defects. The importance of this topic is due to the potential for premature components damage under cyclic loading, especially in critical applications such as aviation and energy, where WAAM (wire arc additive manufacturing) can save significant manufacturing time by up to 40 – 60 %. The study evaluates the impact of technological defects on the fatigue strength of 08CrMoV and 30CrMnSi steels produced by WAAM. The authors used different surfacing modes to generate various types of defects, including macrodefects such as pores, lack of fusion, and surface concentrators, as well as microstructural defects like Widmannstetten structures and grain diversity. Defect-free samples were also produced. The authors performed metallographic analysis to investigate the metals microstructure, distribution and nature of any possible defects. Samples were etched using a 4 % aqueous HNO 3 solution. Fatigue tests were conducted on a specialized machine with sample loading following the cantilever bending method. Defect-free samples of both steels exhibited the highest fatigue strength. The presence of any type of defect, whether microstructural or macrostructural, resulted in a decrease in fatigue strength. Macrostructural defects, such as large pores and lack of fusion, had a stronger impact on the material fatigue strength compared to microstructural defects. Additionally, it was found that the presence of a surface concentrator had a greater influence on initiation of a primary fatigue crack than the presence of large non-melted regions in the sample central part.
- 2 July 2026
- Published by National University of Science and Technology MISiS in Izvestiya. Ferrous Metallurgy
- Vol. 69 (3) , 242-249
Open AccessEffect of the defects occurring during WAAM process on fatigue strength of 08CrMoV and 30CrMnSi steels
At the moment, there are very few studies on fatigue failure of the products obtained by additive manufacturing, especially when fatigue failure occurs due to various types of defects. The importance of this topic is due to the potential for premature components damage under cyclic loading, especially in critical applications such as aviation and energy, where WAAM (wire arc additive manufacturing) can save significant manufacturing time by up to 40 – 60 %. The study evaluates the impact of technological defects on the fatigue strength of 08CrMoV and 30CrMnSi steels produced by WAAM. The authors used different surfacing modes to generate various types of defects, including macrodefects such as pores, lack of fusion, and surface concentrators, as well as microstructural defects like Widmannstetten structures and grain diversity. Defect-free samples were also produced. The authors performed metallographic analysis to investigate the metals microstructure, distribution and nature of any possible defects. Samples were etched using a 4 % aqueous HNO 3 solution. Fatigue tests were conducted on a specialized machine with sample loading following the cantilever bending method. Defect-free samples of both steels exhibited the highest fatigue strength. The presence of any type of defect, whether microstructural or macrostructural, resulted in a decrease in fatigue strength. Macrostructural defects, such as large pores and lack of fusion, had a stronger impact on the material fatigue strength compared to microstructural defects. Additionally, it was found that the presence of a surface concentrator had a greater influence on initiation of a primary fatigue crack than the presence of large non-melted regions in the sample central part.
- 30 September 2025
- Published by Nosov Magnitogorsk State Technical University in Vestnik of Nosov Magnitogorsk State Technical University
- Vol. 23 (3)
Structural Changes in Carbon Steels During Contact Interaction with a Hard Alloy Under Conditions of Build-Up Formation During Cutting
The article is devoted to the study of structural changes occurring in the contact layers of carbon steels during friction with a hard alloy. The relevance of this work is due to the need to understand the processes occurring in the friction zone in order to develop more effective lubrication methods, reduce wear and increase the durability of mechanisms. The purpose was to study the mechanism of build-up formation as a result of stagnant processes during cutting. To achieve this goal, experimental methods were used, including electron microscopy, X-ray diffraction analysis and other methods. The scientific novelty of the work is to develop the features of the mechanism of structural changes in the contact layers of 20, 45, U8 steels during friction while cutting, affecting adhesion to a hard alloy. The results of studies of structural changes in steels during contact with a hard alloy are presented. It is shown that as a result of high deformation rates and contact loads, high-speed heating and the formation of nonequilibrium structures affecting adhesion to a hard alloy are realized. The practical significance of the work lies in the possibility of using the results obtained to develop new technologies capable of increasing the wear resistance and durability of mechanisms operating under friction conditions with hard alloys. In addition, the results of the study may be useful for developing new lubricants and reducing wear of cutting tools. The direction of development of this work may include further study of the effect of various wear-resistant nanostructured coatings on reducing the coefficient of friction and wear of cutting tools during the cutting process. Such tools are characterized by increased hardness of the surface layer and high heat resistance, they are resistant to oxidative and corrosive processes, demonstrate low tendency for adhesion to the processed material and exhibit stable strength properties.
- 30 September 2025
- Published by Nosov Magnitogorsk State Technical University in Vestnik of Nosov Magnitogorsk State Technical University
- Vol. 23 (3)
Structural Changes in Carbon Steels During Contact Interaction with a Hard Alloy Under Conditions of Build-Up Formation During Cutting
The article is devoted to the study of structural changes occurring in the contact layers of carbon steels during friction with a hard alloy. The relevance of this work is due to the need to understand the processes occurring in the friction zone in order to develop more effective lubrication methods, reduce wear and increase the durability of mechanisms. The purpose was to study the mechanism of build-up formation as a result of stagnant processes during cutting. To achieve this goal, experimental methods were used, including electron microscopy, X-ray diffraction analysis and other methods. The scientific novelty of the work is to develop the features of the mechanism of structural changes in the contact layers of 20, 45, U8 steels during friction while cutting, affecting adhesion to a hard alloy. The results of studies of structural changes in steels during contact with a hard alloy are presented. It is shown that as a result of high deformation rates and contact loads, high-speed heating and the formation of nonequilibrium structures affecting adhesion to a hard alloy are realized. The practical significance of the work lies in the possibility of using the results obtained to develop new technologies capable of increasing the wear resistance and durability of mechanisms operating under friction conditions with hard alloys. In addition, the results of the study may be useful for developing new lubricants and reducing wear of cutting tools. The direction of development of this work may include further study of the effect of various wear-resistant nanostructured coatings on reducing the coefficient of friction and wear of cutting tools during the cutting process. Such tools are characterized by increased hardness of the surface layer and high heat resistance, they are resistant to oxidative and corrosive processes, demonstrate low tendency for adhesion to the processed material and exhibit stable strength properties.
- Open Access
- 31 August 2024
- Published by National University of Science and Technology MISiS in Izvestiya. Ferrous Metallurgy
- Vol. 67 (4) , 409-416
Low-cycle fatigue of welded joint from steel of X70 strength class
Steels of X70 strength class are particularly widely used in the field of heavy engineering. One of the most important issues when choosing steel for structures is its behavior under cyclic loads. It is difficult to find a description of the behavior of all zones of the welded joint under fatigue. The purpose of this study was to determine the fatigue characteristics of welded joints made of the Russian analogue of S690QL steel with fixation of acoustic and magnetic parameters for their use in the diagnosis. The objects of the study were the samples from domestic steel of X70 strength class. The chemical composition was determined using optical emission spectrometry. The grinds for microstructural analysis were prepared according to the standard technique with etching in the metal. The fatigue test was carried out on a specialized test bench. The authors used the acoustic system AIS NRK-3 for acoustic measurements and the acoustic parameter D – as an informative parameter. A MA-412MM coercitimeter was applied to evaluate the magnetic characteristics. The following were evaluated: residual magnetization Br , coercive force Hc , Hc/Br ratio. The smallest number of cycles corresponds to the deposited metal zone. The decrease in amplitude showed a significant variation in the behavior of the material depending on the junction zone. However, the curves for heat affected zone (HAZ) and the deposited metal are practically the same. HAZ differs to a lesser extent from the base metal than the deposited metal zone. The graph of the acoustic parameter in its form is the reverse of the magnetic characteristics graph. Thus, there is a minimum for the acoustic parameter, depending on the operating time, and a maximum for the magnetic characteristics. For both graphs, the extremum is the point corresponding to the operating time of 0.6.
- 31 August 2024
- Published by National University of Science and Technology MISiS in Izvestiya. Ferrous Metallurgy
- Vol. 67 (4) , 409-416
Open AccessLow-cycle fatigue of welded joint from steel of X70 strength class
Steels of X70 strength class are particularly widely used in the field of heavy engineering. One of the most important issues when choosing steel for structures is its behavior under cyclic loads. It is difficult to find a description of the behavior of all zones of the welded joint under fatigue. The purpose of this study was to determine the fatigue characteristics of welded joints made of the Russian analogue of S690QL steel with fixation of acoustic and magnetic parameters for their use in the diagnosis. The objects of the study were the samples from domestic steel of X70 strength class. The chemical composition was determined using optical emission spectrometry. The grinds for microstructural analysis were prepared according to the standard technique with etching in the metal. The fatigue test was carried out on a specialized test bench. The authors used the acoustic system AIS NRK-3 for acoustic measurements and the acoustic parameter D – as an informative parameter. A MA-412MM coercitimeter was applied to evaluate the magnetic characteristics. The following were evaluated: residual magnetization Br , coercive force Hc , Hc/Br ratio. The smallest number of cycles corresponds to the deposited metal zone. The decrease in amplitude showed a significant variation in the behavior of the material depending on the junction zone. However, the curves for heat affected zone (HAZ) and the deposited metal are practically the same. HAZ differs to a lesser extent from the base metal than the deposited metal zone. The graph of the acoustic parameter in its form is the reverse of the magnetic characteristics graph. Thus, there is a minimum for the acoustic parameter, depending on the operating time, and a maximum for the magnetic characteristics. For both graphs, the extremum is the point corresponding to the operating time of 0.6.
- Open Access
- 25 February 2024
- Published by National University of Science and Technology MISiS in Izvestiya. Ferrous Metallurgy
- Vol. 67 (1) , 65-72
Structure and its defects in additive manufacturing of stainless steels by laser melting and electric arc surfacing
Currently, there is an active development and study of additive technologies. Metal 3D printing makes it possible to obtain parts and structures of complex configuration using a minimum of shaping operations, which can lead to a reduction in overall cost of the resulting products. In this paper, we studied the structure formation in manufacture of products made of stainless steels 10Cr12Ni10Ti (analogue of AISI 321) and 08Cr18Ni9 (analogue of AISI 304) by additive methods – SLM (Selective Laser Melting) and WAAM (Wire Arc Additive Manufacturing). In the course of microstructural analysis, it was found that during the manufacture of products using SLM technology, small austenitic grains oriented in the direction of heat removal are formed, and with WAAM method, austenite is formed mainly in form of dendrites. It is shown that porosity is formed during manufacture of the samples by SLM method, which is associated with non-melting of individual powder particles. When implementing additive manufacturing by WAAM (electric arc surfacing), there is no increased porosity. In the course of the study, a new defect of the structure formed during the manufacture of products by both methods was revealed – formation of interface boundaries between layers, which is associated with the technology of additive manufacturing itself. When manufacturing a WAAM product, it manifests itself more clearly than when obtaining metal by SLM. Boundaries of the surfacing rollers in the manufacture of products by SLM accumulate various intermetallides and structural defects more intensively, relative to WAAM. As a result of the small relative volume of one surfacing roller, compared with WAAM, accumulation of these defects and intermetallides can act as an effective barrier during movement of dislocations, which can lead to an increase in the strength properties of products.
- 25 February 2024
- Published by National University of Science and Technology MISiS in Izvestiya. Ferrous Metallurgy
- Vol. 67 (1) , 65-72
Open AccessStructure and its defects in additive manufacturing of stainless steels by laser melting and electric arc surfacing
Currently, there is an active development and study of additive technologies. Metal 3D printing makes it possible to obtain parts and structures of complex configuration using a minimum of shaping operations, which can lead to a reduction in overall cost of the resulting products. In this paper, we studied the structure formation in manufacture of products made of stainless steels 10Cr12Ni10Ti (analogue of AISI 321) and 08Cr18Ni9 (analogue of AISI 304) by additive methods – SLM (Selective Laser Melting) and WAAM (Wire Arc Additive Manufacturing). In the course of microstructural analysis, it was found that during the manufacture of products using SLM technology, small austenitic grains oriented in the direction of heat removal are formed, and with WAAM method, austenite is formed mainly in form of dendrites. It is shown that porosity is formed during manufacture of the samples by SLM method, which is associated with non-melting of individual powder particles. When implementing additive manufacturing by WAAM (electric arc surfacing), there is no increased porosity. In the course of the study, a new defect of the structure formed during the manufacture of products by both methods was revealed – formation of interface boundaries between layers, which is associated with the technology of additive manufacturing itself. When manufacturing a WAAM product, it manifests itself more clearly than when obtaining metal by SLM. Boundaries of the surfacing rollers in the manufacture of products by SLM accumulate various intermetallides and structural defects more intensively, relative to WAAM. As a result of the small relative volume of one surfacing roller, compared with WAAM, accumulation of these defects and intermetallides can act as an effective barrier during movement of dislocations, which can lead to an increase in the strength properties of products.
- Open Access
- 1 January 2023
- Published by Togliatti State University in Frontier materials & technologies
- No. 3,p. 43-51
Control of the dynamic stability of metal-cutting systems in the process of cutting based on the fractality of roughness of the machined surface
The problem of increasing the efficiency of mechanical treatment within modern automated production is relevant for many branches of the processing industry. This problem requires a deep study of the physical processes occurring during cutting. The urgency of the problem increases even more with the development of digital production in our country. Today, in the presence of a wide range of products, enterprises are forced to create conditions for reducing the technological cycle when manufacturing a particular product. To carry out the study, an experiment was conducted in which the U8 carbon steel was used as the processed material, and the T15K6 alloy was used as the tool material. During the experiment, the authors observed a change in the roughness of the machined surface depending on the cutting speed. The paper considers the possibility of assessing the quality of the surface layer during cutting based on fractal and neural network modeling. It is identified that the fractal dimension shows the regularity of the reproduction of the machined surface roughness during cutting. The calculated fractal dimension of the machined surface roughness correlates well with the values of the machined surface roughness (correlation coefficient is 0.8–0.9). A neural network structure has been developed, which allows controlling the machined surface quality depending on the cutting conditions. The authors studied the possibility of using neural network models to control technological systems of cutting treatment. When creating digital twins, it is proposed to take into account factors affecting the quality of the treated surface and processing performance, which are poorly accounted for in modeling, as well as when conducting full-scale experiments during machining. Such factors are wear of the cutting tool, the process of plastic deformation, and cutting dynamics.
- 1 January 2023
- Published by Togliatti State University in Frontier materials & technologies
- No. 3,p. 43-51
Open AccessControl of the dynamic stability of metal-cutting systems in the process of cutting based on the fractality of roughness of the machined surface
The problem of increasing the efficiency of mechanical treatment within modern automated production is relevant for many branches of the processing industry. This problem requires a deep study of the physical processes occurring during cutting. The urgency of the problem increases even more with the development of digital production in our country. Today, in the presence of a wide range of products, enterprises are forced to create conditions for reducing the technological cycle when manufacturing a particular product. To carry out the study, an experiment was conducted in which the U8 carbon steel was used as the processed material, and the T15K6 alloy was used as the tool material. During the experiment, the authors observed a change in the roughness of the machined surface depending on the cutting speed. The paper considers the possibility of assessing the quality of the surface layer during cutting based on fractal and neural network modeling. It is identified that the fractal dimension shows the regularity of the reproduction of the machined surface roughness during cutting. The calculated fractal dimension of the machined surface roughness correlates well with the values of the machined surface roughness (correlation coefficient is 0.8–0.9). A neural network structure has been developed, which allows controlling the machined surface quality depending on the cutting conditions. The authors studied the possibility of using neural network models to control technological systems of cutting treatment. When creating digital twins, it is proposed to take into account factors affecting the quality of the treated surface and processing performance, which are poorly accounted for in modeling, as well as when conducting full-scale experiments during machining. Such factors are wear of the cutting tool, the process of plastic deformation, and cutting dynamics.
- Open Access
- 21 March 2022
- Published by Volga State University of Water Transport in Russian Journal of Water Transport
- No. 70,p. 30-38
Evaluation of the effect of heat treatment on the structure parameters and cold resistance of metals produced by additive electric arc growth
In this work, we studied the influence of the type and mode of heat treatment on the structure and parameters of cold resistance of 09Mn2Si and 07Cr25Ni13 steels obtained by additive electric arc growth. It is shown that, under optimal printing conditions, a relatively uniform and fine-grained material structure is observed in 09Mn2Si steel, while a dendritic structure is observed in the 07Cr25Ni13 alloy. Heat treatment of the investigated alloys leads to a more uniform distribution of structural components in metals, and in steel 07Cr25Ni13 the dendrites are destroyed, which leads to a decrease in the anisotropy of material properties. Also, heat treatment leads to a significant reduction in internal residual stresses in the material. The results of the study of impact strength in a wide range of low temperatures show that in the initial state after surfacing, the investigated alloys have a significant anisotropy of impact strength (up to 8 and 25% for alloy 09Mn2Si and 07Cr25Ni13, respectively). Heat treatment significantly reduces the anisotropy of the properties of the studied alloys and increases the values of impact strength. So for steel 09Mn2Si after heat treatment, an increase in impact strength by more than 1.5 times is observed over the entire temperature range. The studies carried out made it possible to identify the temperature range of the ductile-brittle transition and the impact strength of 09Mn2Si and 07Cr25Ni13 alloys, which is of great practical importance in the manufacture of parts and structural elements of the Northern version.
- 21 March 2022
- Published by Volga State University of Water Transport in Russian Journal of Water Transport
- No. 70,p. 30-38
Open AccessEvaluation of the effect of heat treatment on the structure parameters and cold resistance of metals produced by additive electric arc growth
In this work, we studied the influence of the type and mode of heat treatment on the structure and parameters of cold resistance of 09Mn2Si and 07Cr25Ni13 steels obtained by additive electric arc growth. It is shown that, under optimal printing conditions, a relatively uniform and fine-grained material structure is observed in 09Mn2Si steel, while a dendritic structure is observed in the 07Cr25Ni13 alloy. Heat treatment of the investigated alloys leads to a more uniform distribution of structural components in metals, and in steel 07Cr25Ni13 the dendrites are destroyed, which leads to a decrease in the anisotropy of material properties. Also, heat treatment leads to a significant reduction in internal residual stresses in the material. The results of the study of impact strength in a wide range of low temperatures show that in the initial state after surfacing, the investigated alloys have a significant anisotropy of impact strength (up to 8 and 25% for alloy 09Mn2Si and 07Cr25Ni13, respectively). Heat treatment significantly reduces the anisotropy of the properties of the studied alloys and increases the values of impact strength. So for steel 09Mn2Si after heat treatment, an increase in impact strength by more than 1.5 times is observed over the entire temperature range. The studies carried out made it possible to identify the temperature range of the ductile-brittle transition and the impact strength of 09Mn2Si and 07Cr25Ni13 alloys, which is of great practical importance in the manufacture of parts and structural elements of the Northern version.
- 3 February 2022
- Published by Trans Tech Publications, Ltd. in Materials Science Forum
- Vol. 1052, 414-419
Optimization of 3D Printing Modes for Electric Arc Surfacing Using a Digital Twin of the Process
The article proposes a method for choosing the optimal modes of 3D printing by electric arc surfacing on CNC machines using a digital twin of the process. As a digital twin, a neural network model is used that approximates the dependence of the stability of the surfacing process and the geometric parameters of the printed layer on the surfacing modes: voltage, current and minute feed. The possibility of optimizing 3D printing modes using neural network modeling based on a modified backpropagation method is shown.
- 3 February 2022
- Published by Trans Tech Publications, Ltd. in Materials Science Forum
- Vol. 1052, 414-419
Optimization of 3D Printing Modes for Electric Arc Surfacing Using a Digital Twin of the Process
The article proposes a method for choosing the optimal modes of 3D printing by electric arc surfacing on CNC machines using a digital twin of the process. As a digital twin, a neural network model is used that approximates the dependence of the stability of the surfacing process and the geometric parameters of the printed layer on the surfacing modes: voltage, current and minute feed. The possibility of optimizing 3D printing modes using neural network modeling based on a modified backpropagation method is shown.