Tetiana Selivorstova
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Tetiana Selivorstova has a total of 24 co-authors. Here are the top co-authors by number of shared publications:
- Vadim Selivorstov
Ukrainian State University of Science and Technologies
3 shared publications - Kateryna Ostrovska
Ukrainian State University of Science and Technologies
2 shared publications - Petro Hubskyi
Electric Energy Department, Railway Research Institute, 50 Józefa Chłopickiego Street, 04-275 Warsaw, Poland
2 shared publications - Valeriy Kuznetsov
Electric Energy Department, Railway Research Institute, 50 Józefa Chłopickiego Street, 04-275 Warsaw, Poland
2 shared publications - Vitaliy Kuznetsov
Ukrainian State University of Science and Technologies
2 shared publications - Yuriy Dotsenko
Ukrainian State University of Science and Technologies
2 shared publications
Latest Publications
- Open Access
- 30 April 2026
- Published by National Metallurgical Academy of Ukraine in Modern Problems of Metalurgy
- No. 29,p. 376-388
ПЕРКОЛЯЦІЙНИЙ ПІДХІД ДО ОПИСУ МІЖДЕНДРИТНОГО ЖИВЛЕННЯ НА ЗАВЕРШАЛЬНІЙ СТАДІЇ ЗАТВЕРДІННЯ МЕТАЛІВ І СПЛАВІВ
The paper examines the physical foundations of interdendritic feeding during the final stage of solidification of metals and alloys. It is shown that the efficiency of shrinkage compensation within the mushy zone is determined not only by the presence of residual liquid phase, but also by the conditions of its transport through the interdendritic space. Particular attention is paid to the role of permeability, local pressure gradients, morphology of liquid channels, and preservation of continuous feeding paths in ensuring the transport capacity of the liquid phase. The mechanisms of shrinkage and gas-shrinkage porosity formation are analyzed, and it is emphasized that the appearance of such defects is directly related to the degradation of the liquid feeding network at high solid fractions. The study summarizes the influence of increasing solid fraction on the narrowing of interdendritic channels, reduction in permeability, localization of liquid flow, and growth of local hydraulic resistance. It is shown that, as the dendritic skeleton evolves toward a coherent solid framework, the liquid phase gradually loses its ability to form a continuous transport network. Under such conditions, even if some amount of liquid remains in the mushy zone, it may no longer participate in real feeding because of topological isolation. This circumstance indicates the limitations of conventional continuum approaches, which mainly operate with averaged characteristics such as permeability, pressure, or liquid fraction, but do not fully capture the structural transformation of the liquid network at the final stage of solidification. To overcome these limitations, the applicability of the percolation approach is substantiated. Within this interpretation, the mushy zone is considered as a two-phase system in which the liquid phase acts as a transport network and the solid phase forms a constraining framework. It is argued that the loss of interdendritic feeding should be associated not with the complete disappearance of the liquid phase, but with the destruction of its global connectivity and the disappearance of a continuous feeding path. Thus, liquid-phase percolation is proposed as a physically meaningful criterion for feeding loss in the mushy zone. The obtained results confirm that the percolation-based interpretation provides a promising theoretical framework for further modeling of solidification processes, localization of feeding paths, and prediction of shrinkage-related defect formation in metallic castings.
- 30 April 2026
- Published by National Metallurgical Academy of Ukraine in Modern Problems of Metalurgy
- No. 29,p. 376-388
Open AccessПЕРКОЛЯЦІЙНИЙ ПІДХІД ДО ОПИСУ МІЖДЕНДРИТНОГО ЖИВЛЕННЯ НА ЗАВЕРШАЛЬНІЙ СТАДІЇ ЗАТВЕРДІННЯ МЕТАЛІВ І СПЛАВІВ
The paper examines the physical foundations of interdendritic feeding during the final stage of solidification of metals and alloys. It is shown that the efficiency of shrinkage compensation within the mushy zone is determined not only by the presence of residual liquid phase, but also by the conditions of its transport through the interdendritic space. Particular attention is paid to the role of permeability, local pressure gradients, morphology of liquid channels, and preservation of continuous feeding paths in ensuring the transport capacity of the liquid phase. The mechanisms of shrinkage and gas-shrinkage porosity formation are analyzed, and it is emphasized that the appearance of such defects is directly related to the degradation of the liquid feeding network at high solid fractions. The study summarizes the influence of increasing solid fraction on the narrowing of interdendritic channels, reduction in permeability, localization of liquid flow, and growth of local hydraulic resistance. It is shown that, as the dendritic skeleton evolves toward a coherent solid framework, the liquid phase gradually loses its ability to form a continuous transport network. Under such conditions, even if some amount of liquid remains in the mushy zone, it may no longer participate in real feeding because of topological isolation. This circumstance indicates the limitations of conventional continuum approaches, which mainly operate with averaged characteristics such as permeability, pressure, or liquid fraction, but do not fully capture the structural transformation of the liquid network at the final stage of solidification. To overcome these limitations, the applicability of the percolation approach is substantiated. Within this interpretation, the mushy zone is considered as a two-phase system in which the liquid phase acts as a transport network and the solid phase forms a constraining framework. It is argued that the loss of interdendritic feeding should be associated not with the complete disappearance of the liquid phase, but with the destruction of its global connectivity and the disappearance of a continuous feeding path. Thus, liquid-phase percolation is proposed as a physically meaningful criterion for feeding loss in the mushy zone. The obtained results confirm that the percolation-based interpretation provides a promising theoretical framework for further modeling of solidification processes, localization of feeding paths, and prediction of shrinkage-related defect formation in metallic castings.
- 26 April 2026
- Published by National Metallurgical Academy of Ukraine in International scientific and technical conference Information technologies in metallurgy and machine building
- p. 406-409
КОНЦЕПТУАЛЬНІ ОСНОВИ ВИЯВЛЕННЯ АНОМАЛІЙ У ПРОМИСЛОВИХ ІНФОРМАЦІЙНИХ СИСТЕМАХ З ВИКОРИСТАННЯМ МАШИННОГО НАВЧАННЯ
The paper provides a conceptual overview of anomaly detection in industrial information systems with a focus on machine learning methods. The discussion emphasizes unsupervised approaches for modeling normal system behavior and detecting deviations without predefined attack patterns. The work is descriptive and aims to clarify the underlying principles rather than present experimental validation.
- 26 April 2026
- Published by National Metallurgical Academy of Ukraine in International scientific and technical conference Information technologies in metallurgy and machine building
- p. 406-409
КОНЦЕПТУАЛЬНІ ОСНОВИ ВИЯВЛЕННЯ АНОМАЛІЙ У ПРОМИСЛОВИХ ІНФОРМАЦІЙНИХ СИСТЕМАХ З ВИКОРИСТАННЯМ МАШИННОГО НАВЧАННЯ
The paper provides a conceptual overview of anomaly detection in industrial information systems with a focus on machine learning methods. The discussion emphasizes unsupervised approaches for modeling normal system behavior and detecting deviations without predefined attack patterns. The work is descriptive and aims to clarify the underlying principles rather than present experimental validation.
- 26 April 2026
- Published by National Metallurgical Academy of Ukraine in International scientific and technical conference Information technologies in metallurgy and machine building
- p. 88-91
ІНТЕГРОВАНИЙ ПЕРКОЛЯЦІЙНИЙ ПІДХІД ДО МОДЕЛЮВАННЯ МІЖДЕНДРИТНОГО ЖИВЛЕННЯ В УМОВАХ ЗАТВЕРДІННЯ ПІД ТИСКОМ
The paper addresses the problem of interdendritic feeding at the final stage of solidification of metals and alloys under external pressure. It is shown that conventional modeling approaches based only on local liquid-phase parameters and mushy-zone permeability do not fully account for the loss of global connectivity of the liquid network, which is critically important for describing defect formation. An integrated percolation-based model of interdendritic feeding is proposed, combining a microstructural description of the dendritic skeleton, a hydrodynamic approach to liquid-phase filtration in a porous medium, and a percolation criterion for preserving a continuous feeding channel. It is substantiated that the loss of connectivity of the liquid network is one of the key mechanisms governing the transition from effective feeding to the formation of shrinkage and gas-shrinkage porosity. Considering external pressure within the model makes it possible to describe more accurately the conditions for preserving interdendritic feeding and to assess its influence on the final stage of solidification. The proposed approach can be used as a theoretical basis for further mathematical modeling of defect formation in cast metals and alloys.
- 26 April 2026
- Published by National Metallurgical Academy of Ukraine in International scientific and technical conference Information technologies in metallurgy and machine building
- p. 88-91
ІНТЕГРОВАНИЙ ПЕРКОЛЯЦІЙНИЙ ПІДХІД ДО МОДЕЛЮВАННЯ МІЖДЕНДРИТНОГО ЖИВЛЕННЯ В УМОВАХ ЗАТВЕРДІННЯ ПІД ТИСКОМ
The paper addresses the problem of interdendritic feeding at the final stage of solidification of metals and alloys under external pressure. It is shown that conventional modeling approaches based only on local liquid-phase parameters and mushy-zone permeability do not fully account for the loss of global connectivity of the liquid network, which is critically important for describing defect formation. An integrated percolation-based model of interdendritic feeding is proposed, combining a microstructural description of the dendritic skeleton, a hydrodynamic approach to liquid-phase filtration in a porous medium, and a percolation criterion for preserving a continuous feeding channel. It is substantiated that the loss of connectivity of the liquid network is one of the key mechanisms governing the transition from effective feeding to the formation of shrinkage and gas-shrinkage porosity. Considering external pressure within the model makes it possible to describe more accurately the conditions for preserving interdendritic feeding and to assess its influence on the final stage of solidification. The proposed approach can be used as a theoretical basis for further mathematical modeling of defect formation in cast metals and alloys.
- 26 April 2026
- Published by National Metallurgical Academy of Ukraine in International scientific and technical conference Information technologies in metallurgy and machine building
- p. 460-464
ЗАСТОСУВАННЯ МЕТОДІВ МАШИННОГО НАВЧАННЯ ДЛЯ ВИЯВЛЕННЯ АНОМАЛІЙ У МЕРЕЖЕВОМУ ТРАФІКУ
This paper investigates the effectiveness of machine learning methods for anomaly detection in network traffic. The main approaches to building intelligent intrusion detection systems (IDS) are analyzed, including signature-based analysis and machine learning-based methods. An experimental comparison of Random Forest, Support Vector Machine, k-Nearest Neighbors, and Multilayer Perceptron algorithms was performed on the NSL-KDD dataset. Classification quality was assessed using Accuracy, Precision, Recall, and F1-score metrics. The results showed that the Random Forest method provides the best balance of accuracy and computational efficiency for real-time network anomaly detection tasks. The prospects of applying ensemble methods and deep learning for improving cyber threat detection quality are identified.
- 26 April 2026
- Published by National Metallurgical Academy of Ukraine in International scientific and technical conference Information technologies in metallurgy and machine building
- p. 460-464
ЗАСТОСУВАННЯ МЕТОДІВ МАШИННОГО НАВЧАННЯ ДЛЯ ВИЯВЛЕННЯ АНОМАЛІЙ У МЕРЕЖЕВОМУ ТРАФІКУ
This paper investigates the effectiveness of machine learning methods for anomaly detection in network traffic. The main approaches to building intelligent intrusion detection systems (IDS) are analyzed, including signature-based analysis and machine learning-based methods. An experimental comparison of Random Forest, Support Vector Machine, k-Nearest Neighbors, and Multilayer Perceptron algorithms was performed on the NSL-KDD dataset. Classification quality was assessed using Accuracy, Precision, Recall, and F1-score metrics. The results showed that the Random Forest method provides the best balance of accuracy and computational efficiency for real-time network anomaly detection tasks. The prospects of applying ensemble methods and deep learning for improving cyber threat detection quality are identified.
- 26 April 2026
- Published by National Metallurgical Academy of Ukraine in International scientific and technical conference Information technologies in metallurgy and machine building
- p. 83-87
ДОСЛІДЖЕННЯ МЕТОДІВ УНІФІКАЦІЇ ТА ПОПЕРЕДНЬОЇ ОБРОБКИ ЕКСПЕРИМЕНТАЛЬНИХ ДАНИХ ДЛЯ ПІДВИЩЕННЯ ЯКОСТІ ІНТЕГРАЦІЇ В ШІ-МОДЕЛІ КОМПЕНСАЦІЇ ЕКСЦЕНТРИСИТЕТУ ВАЛКІВ
The paper addresses the issues of unification and preprocessing of experimental data for their effective use in AI models for roll eccentricity compensation in sheet rolling processes. It is substantiated that the performance quality of intelligent models largely depends on the consistency, completeness, and informativeness of the input data. Approaches to time-series synchronization, data cleaning, noise filtering, normalization, and feature engineering are analyzed. It is shown that the application of data unification and preprocessing procedures improves the quality of data integration into AI models and creates prerequisites for more accurate roll eccentricity compensation.
- 26 April 2026
- Published by National Metallurgical Academy of Ukraine in International scientific and technical conference Information technologies in metallurgy and machine building
- p. 83-87
ДОСЛІДЖЕННЯ МЕТОДІВ УНІФІКАЦІЇ ТА ПОПЕРЕДНЬОЇ ОБРОБКИ ЕКСПЕРИМЕНТАЛЬНИХ ДАНИХ ДЛЯ ПІДВИЩЕННЯ ЯКОСТІ ІНТЕГРАЦІЇ В ШІ-МОДЕЛІ КОМПЕНСАЦІЇ ЕКСЦЕНТРИСИТЕТУ ВАЛКІВ
The paper addresses the issues of unification and preprocessing of experimental data for their effective use in AI models for roll eccentricity compensation in sheet rolling processes. It is substantiated that the performance quality of intelligent models largely depends on the consistency, completeness, and informativeness of the input data. Approaches to time-series synchronization, data cleaning, noise filtering, normalization, and feature engineering are analyzed. It is shown that the application of data unification and preprocessing procedures improves the quality of data integration into AI models and creates prerequisites for more accurate roll eccentricity compensation.
- 17 January 2026
- Published by Springer Nature
- p. 624-634
Digital Simulation of Metallurgical Production: 3D Scene Development of Steel-Making Furnaces in Unreal Engine 5
- 17 January 2026
- Published by Springer Nature
- p. 624-634
Digital Simulation of Metallurgical Production: 3D Scene Development of Steel-Making Furnaces in Unreal Engine 5
- 19 June 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 1-4
Gamification of Electrical Engineering Education: Development of an Educational VR Simulation
The modern educational process is undergoing significant transformations under the influence of digital technologies. One of the directions for improving teaching methods is the implementation of gamification and the use of virtual reality (VR) technologies. In the field of electrical engineering education, traditional methods often prove to be insufficiently effective in engaging students and fostering a deep understanding of complex technical concepts. The use of VR simulations, enhanced with gamification elements, can improve the learning process, increase material retention, and boost student motivation [1], [2].
- 19 June 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 1-4
Gamification of Electrical Engineering Education: Development of an Educational VR Simulation
The modern educational process is undergoing significant transformations under the influence of digital technologies. One of the directions for improving teaching methods is the implementation of gamification and the use of virtual reality (VR) technologies. In the field of electrical engineering education, traditional methods often prove to be insufficiently effective in engaging students and fostering a deep understanding of complex technical concepts. The use of VR simulations, enhanced with gamification elements, can improve the learning process, increase material retention, and boost student motivation [1], [2].
- 19 June 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 1-4
Ai for Teaching Subjects of Electrical Engineering
Undoubtedly, Artificial Intelligence (AI) is becoming an integral part of modern education, offering new approaches to learning and teaching. Its implementation is particularly relevant in the context of electrical engineering disciplines, which are characterized by a high level of complexity and require the integration of theoretical knowledge with practical skills.
- 19 June 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 1-4
Ai for Teaching Subjects of Electrical Engineering
Undoubtedly, Artificial Intelligence (AI) is becoming an integral part of modern education, offering new approaches to learning and teaching. Its implementation is particularly relevant in the context of electrical engineering disciplines, which are characterized by a high level of complexity and require the integration of theoretical knowledge with practical skills.
- Open Access
- 4 April 2025
- Published by Private Company Technology Center in Technology audit and production reserves
- Vol. 2 (1(82)) , 19-23
Construction of a kinetic equation of carbon removal for controlling steel melting in the metallurgical system “cupola furnace – small converter”
The object of research in the paper is the process of steelmaking in a small converter, which works in tandem with a cupola furnace. The existing problem is that the control of the process of obtaining steel in an oxygen converter is complicated by the need to determine in real time the current chemical composition of the melt, in particular carbon. This is due to the fact that the rate of carbon removal is too high, as a result of which the process of carbon removal is transient. Therefore, it is too difficult to implement regulation based on feedback on continuous measurement. The presence of the specified problem requires solutions related to the possibilities of developing or improving software control of the process. It is shown that in certain sections of the process within each time section of oxygen purging of the melt in the converter, the kinetic curve has a linear form with a constant coefficient value in front of the inlet mine. But the value of the initial coefficient for each equation that describes the process within its limits changes. This allows to state that in case of a change in the initial condition, the kinetic curves shift relative to each other in parallel. On this basis, a system of equations has been constructed that describes the process of carbon removal in a small oxygen converter that receives liquid iron from a cupola furnace. It has been shown that to use the obtained system of equations, it is necessary to know the initial carbon content in the melt discharged from the cupola furnace, and it depends on the method of oxygen supply to the cupola furnace. Based on the modeling of this process in two variants – using a “sharp blow” and supplying oxygen to the air blown into the tuyeres, a nomogram has been constructed. It allows to determine the initial carbon content for the practical use of the obtained system of equations. Using the obtained system makes it possible to determine the time after which oxygen cutoff should be made. This will allow to decide to implement software control of the melt blowing process in the converter. The presented study will be useful for machine-building enterprises that have foundry shops in their structure, where cast iron is smelted for the manufacture of castings.
- 4 April 2025
- Published by Private Company Technology Center in Technology audit and production reserves
- Vol. 2 (1(82)) , 19-23
Open AccessConstruction of a kinetic equation of carbon removal for controlling steel melting in the metallurgical system “cupola furnace – small converter”
The object of research in the paper is the process of steelmaking in a small converter, which works in tandem with a cupola furnace. The existing problem is that the control of the process of obtaining steel in an oxygen converter is complicated by the need to determine in real time the current chemical composition of the melt, in particular carbon. This is due to the fact that the rate of carbon removal is too high, as a result of which the process of carbon removal is transient. Therefore, it is too difficult to implement regulation based on feedback on continuous measurement. The presence of the specified problem requires solutions related to the possibilities of developing or improving software control of the process. It is shown that in certain sections of the process within each time section of oxygen purging of the melt in the converter, the kinetic curve has a linear form with a constant coefficient value in front of the inlet mine. But the value of the initial coefficient for each equation that describes the process within its limits changes. This allows to state that in case of a change in the initial condition, the kinetic curves shift relative to each other in parallel. On this basis, a system of equations has been constructed that describes the process of carbon removal in a small oxygen converter that receives liquid iron from a cupola furnace. It has been shown that to use the obtained system of equations, it is necessary to know the initial carbon content in the melt discharged from the cupola furnace, and it depends on the method of oxygen supply to the cupola furnace. Based on the modeling of this process in two variants – using a “sharp blow” and supplying oxygen to the air blown into the tuyeres, a nomogram has been constructed. It allows to determine the initial carbon content for the practical use of the obtained system of equations. Using the obtained system makes it possible to determine the time after which oxygen cutoff should be made. This will allow to decide to implement software control of the melt blowing process in the converter. The presented study will be useful for machine-building enterprises that have foundry shops in their structure, where cast iron is smelted for the manufacture of castings.
- 11 September 2024
- Published by The Dnipropetrovsk State University of Internal Affairs in Naukovyy Visnyk Dnipropetrovs'kogo Derzhavnogo Universytety Vnutrishnikh Sprav
- No. 2
КІБЕРБЕЗПЕКА В УПРАВЛІННІ ЛАНЦЮГАМИ ПОСТАЧАНЬ (SCM)
Кібербезпека в управлінні ланцюгами постачань (SCM) стає все більш актуальною, оскільки сучасні компанії все більше використовують інформаційні технології та цифрові системи. А самі ланцюги постачань стають все більш розгалуженими та включають все більше учасників. З такою кількістю точок взаємодії та сторонніх постачальників і покупців важко відслідковувати, чи всі сторони дотримуються належних протоколів кібербезпеки. Hозглянуто сутність управління ланцюгами постачань та проаналізовано роль кібербезпеки в системі управління. Зазначено, що в сучасних умовах кібербезпека стає елементом управління ланцюгами постачань. Проаналізовано основні види ризиків та кіберзагоз в ланцюгах постачань, зокрема питання безпеки сторонніх постачальників. Запропоновано заходи щодо усунення кіберризиків та підвищення кібербезпеки в управлінні ланцюгами постачань. Застосовуючи проактивний підхід і впроваджуючи потужні заходи кібербезпеки, компанії можуть зменшити ризик кібератак і забезпечити безпеку свого ланцюжка постачань.
- 11 September 2024
- Published by The Dnipropetrovsk State University of Internal Affairs in Naukovyy Visnyk Dnipropetrovs'kogo Derzhavnogo Universytety Vnutrishnikh Sprav
- No. 2
КІБЕРБЕЗПЕКА В УПРАВЛІННІ ЛАНЦЮГАМИ ПОСТАЧАНЬ (SCM)
Кібербезпека в управлінні ланцюгами постачань (SCM) стає все більш актуальною, оскільки сучасні компанії все більше використовують інформаційні технології та цифрові системи. А самі ланцюги постачань стають все більш розгалуженими та включають все більше учасників. З такою кількістю точок взаємодії та сторонніх постачальників і покупців важко відслідковувати, чи всі сторони дотримуються належних протоколів кібербезпеки. Hозглянуто сутність управління ланцюгами постачань та проаналізовано роль кібербезпеки в системі управління. Зазначено, що в сучасних умовах кібербезпека стає елементом управління ланцюгами постачань. Проаналізовано основні види ризиків та кіберзагоз в ланцюгах постачань, зокрема питання безпеки сторонніх постачальників. Запропоновано заходи щодо усунення кіберризиків та підвищення кібербезпеки в управлінні ланцюгами постачань. Застосовуючи проактивний підхід і впроваджуючи потужні заходи кібербезпеки, компанії можуть зменшити ризик кібератак і забезпечити безпеку свого ланцюжка постачань.