Vasily Ivanovich Lyashenko
Research Subjects
Vasily Ivanovich Lyashenko has a total of 61 co-authors. Here are the top co-authors by number of shared publications:
- Viktor A. Shapovalov
Kryvyi Rih National University , Kryvyi Rih , Ukraine
11 shared publications - Tamara Dudar
National Aviation University , Kyiv , Ukraine
8 shared publications GP «UkrNIPII promtekhnologii»
7 shared publications- Tatiana Chekushina
Institute of Comprehensive Exploitation of Mineral Resources Russian Academy of Sciences
5 shared publications - Vladimir Ivanovich Golik
Department “Technique and Technology of Mining and Oil and Gas Production”, Moscow Polytechnic University, 38, B. Semenovskaya St., Moscow 107023, Russia
5 shared publications - Arkady Gurin
Kryvyi Rih National University , Kryvyi Rih , Ukraine
4 shared publications
Latest Publications
- Open Access
- 18 December 2025
- Published by Ukrainian Geological Company in Мінеральні ресурси України
- No. 4
Обґрунтування ефективності технології підземної розробки рудних родовищ методами математичного моделювання
Розглянуто обґрунтування ефективності технологій підземної розробки рудних родовищ методами математичного моделювання та мінімізації відходів гірничого виробництва. Це забезпечує підвищення економічної ефективності й екологічної безпеки розробки рудних родовищ, а також раціональне використання й охорону надр. Наведено результати аналізу наукових публікацій та патентної документації в галузі підземної розробки запасів рудних родовищ, обґрунтування технологічних і геомеханічних параметрів експлуатаційних блоків; лабораторні та виробничі експерименти; фізичне моделювання за допомогою математичного апарату прикладних програм “Maple 9.5” та “Microsoft Exсel” за стандартними та новими методиками за участі авторів. Відмічено, що збереження масиву гірських порід і земної поверхні залежить від напружено-деформованого стану та досягається шляхом закладки техногенних порожнин твердіючими сумішами різного складу та міцності від 1,2 до 6,0 МПа. Показано, що збагачення відбитої гірської маси на модульних установках дозволить отримати близько 40 % відсортованої позабалансової руди та порожньої породи без подання їх на земну поверхню. Такі технології ефективні, коли 40 % багатої руди подається на земну поверхню, а 60 % бідної, некондиційної та забалансової руди вилуговується під землею.
- 18 December 2025
- Published by Ukrainian Geological Company in Мінеральні ресурси України
- No. 4
Open AccessОбґрунтування ефективності технології підземної розробки рудних родовищ методами математичного моделювання
Розглянуто обґрунтування ефективності технологій підземної розробки рудних родовищ методами математичного моделювання та мінімізації відходів гірничого виробництва. Це забезпечує підвищення економічної ефективності й екологічної безпеки розробки рудних родовищ, а також раціональне використання й охорону надр. Наведено результати аналізу наукових публікацій та патентної документації в галузі підземної розробки запасів рудних родовищ, обґрунтування технологічних і геомеханічних параметрів експлуатаційних блоків; лабораторні та виробничі експерименти; фізичне моделювання за допомогою математичного апарату прикладних програм “Maple 9.5” та “Microsoft Exсel” за стандартними та новими методиками за участі авторів. Відмічено, що збереження масиву гірських порід і земної поверхні залежить від напружено-деформованого стану та досягається шляхом закладки техногенних порожнин твердіючими сумішами різного складу та міцності від 1,2 до 6,0 МПа. Показано, що збагачення відбитої гірської маси на модульних установках дозволить отримати близько 40 % відсортованої позабалансової руди та порожньої породи без подання їх на земну поверхню. Такі технології ефективні, коли 40 % багатої руди подається на земну поверхню, а 60 % бідної, некондиційної та забалансової руди вилуговується під землею.
- Open Access
- 1 December 2025
- Published by Walter de Gruyter GmbH in Mining Revue
- Vol. 31 (4) , 56-62
Improving Industrial and Environmental Safety When Implementing Technologies of Liquid-Phase Reduction of Iron Oxides
The article examines the main scientific and practical results of the research on improving the envi-ronmental safety of ironmaking processes through the implementation of liquid-phase iron oxide reduction technologies. The current state of industrial and environmental safety in coke-based ironmak-ing using traditional technologies and production processes (coking, sintering, and blast furnace) is described. The results of a comparative analysis of hazardous production factors and harmful emis-sions into the environment from traditional ironmaking technologies and liquid-phase iron oxide re-duction technologies are presented. It is established that the implementation of the liquid-phase iron reduction technology eliminates numerous hazardous technological operations and reduces the envi-ronmental impact of metallurgical production. It is shown that the automation of liquid-phase reduc-tion processes excludes the presence of workers in zones of high temperatures, intense radiation, and other hazardous production factors. The research results can be applied when implementing alterna-tive nonblast-furnace iron production methods.
- 1 December 2025
- Published by Walter de Gruyter GmbH in Mining Revue
- Vol. 31 (4) , 56-62
Open AccessImproving Industrial and Environmental Safety When Implementing Technologies of Liquid-Phase Reduction of Iron Oxides
The article examines the main scientific and practical results of the research on improving the envi-ronmental safety of ironmaking processes through the implementation of liquid-phase iron oxide reduction technologies. The current state of industrial and environmental safety in coke-based ironmak-ing using traditional technologies and production processes (coking, sintering, and blast furnace) is described. The results of a comparative analysis of hazardous production factors and harmful emis-sions into the environment from traditional ironmaking technologies and liquid-phase iron oxide re-duction technologies are presented. It is established that the implementation of the liquid-phase iron reduction technology eliminates numerous hazardous technological operations and reduces the envi-ronmental impact of metallurgical production. It is shown that the automation of liquid-phase reduc-tion processes excludes the presence of workers in zones of high temperatures, intense radiation, and other hazardous production factors. The research results can be applied when implementing alterna-tive nonblast-furnace iron production methods.
- Open Access
- 1 March 2025
- Published by Walter de Gruyter GmbH in Mining Revue
- Vol. 31 (1) , 77-87
Increasing the Efficiency and Environmental Safety of Technologies for Extracting Metals from Processing Tailings
One of the most problematic areas of metal extraction from tailings of metal-containing mineral pro-cessing is the complexity of mineral mining and processing tailings utilization without extracting metals and sulfur compounds from them. This is hampered by insufficient efficiency of their secondary pro-cessing technologies. The study utilized the following data from literary sources and patent documentation in the field of technologies and technical means for metal extraction from tailings of metal-containing mineral processing; laboratory and production experiments; physical modeling of metal extraction from tailings of metal-containing mineral processing; data array processing using statistical and probability theory methods, as well as mathematical modeling. The paper presents the main scientific and practical results of research and development of new technologies and technical means for metal extraction from ore processing tailings. Mechanochemical processes during ore enrichment tail-ings utilization into man-made voids and activation of useful ingredient extraction processes are de-scribed. It is shown that mechanic-chemical activation of enrichment tailings in a disintegrator increases metal extraction into solution by 10–25% during one processing cycle by two orders of magnitude faster than agitation leaching and can increase extraction during multiple processing. The use of activation of hardening backfill mixture components at mining enterprises leads to an increase in their activity for each apparatus by up to 10–40%. The conducted studies are a step towards creating a highly efficient technology for ore enrichment tailings utilization with the production of metals and hardening mixture components. The main advantages of the technology are the possibility of utilizing enrichment waste with a storage time of more than 10 years and obtaining metals in an amount of 20 to 60% of their content in the tailings. Mechanochemical activation during a single treatment increases metal ex-traction into solution by up to 25% compared to the base value and has a reserve for increase with an increase in processing cycles. Activation in a disintegrator without leaching increases the strength of the hardening mixture with the addition of cement from 1.30 to 1.52 MPa or by 17%. The mechanochemical technology is recommended for implementation at enterprises of the mining industries. The phenomenon of activation during processing in a disintegrator has been confirmed in related industries. The results of the research can be used in the extraction of metals from tailings of metal-containing minerals at mining and processing enterprises of Ukraine, the Republic of Kazakhstan, the Republic of Kyrgyzstan and other developed mining countries of the world.
- 1 March 2025
- Published by Walter de Gruyter GmbH in Mining Revue
- Vol. 31 (1) , 77-87
Open AccessIncreasing the Efficiency and Environmental Safety of Technologies for Extracting Metals from Processing Tailings
One of the most problematic areas of metal extraction from tailings of metal-containing mineral pro-cessing is the complexity of mineral mining and processing tailings utilization without extracting metals and sulfur compounds from them. This is hampered by insufficient efficiency of their secondary pro-cessing technologies. The study utilized the following data from literary sources and patent documentation in the field of technologies and technical means for metal extraction from tailings of metal-containing mineral processing; laboratory and production experiments; physical modeling of metal extraction from tailings of metal-containing mineral processing; data array processing using statistical and probability theory methods, as well as mathematical modeling. The paper presents the main scientific and practical results of research and development of new technologies and technical means for metal extraction from ore processing tailings. Mechanochemical processes during ore enrichment tail-ings utilization into man-made voids and activation of useful ingredient extraction processes are de-scribed. It is shown that mechanic-chemical activation of enrichment tailings in a disintegrator increases metal extraction into solution by 10–25% during one processing cycle by two orders of magnitude faster than agitation leaching and can increase extraction during multiple processing. The use of activation of hardening backfill mixture components at mining enterprises leads to an increase in their activity for each apparatus by up to 10–40%. The conducted studies are a step towards creating a highly efficient technology for ore enrichment tailings utilization with the production of metals and hardening mixture components. The main advantages of the technology are the possibility of utilizing enrichment waste with a storage time of more than 10 years and obtaining metals in an amount of 20 to 60% of their content in the tailings. Mechanochemical activation during a single treatment increases metal ex-traction into solution by up to 25% compared to the base value and has a reserve for increase with an increase in processing cycles. Activation in a disintegrator without leaching increases the strength of the hardening mixture with the addition of cement from 1.30 to 1.52 MPa or by 17%. The mechanochemical technology is recommended for implementation at enterprises of the mining industries. The phenomenon of activation during processing in a disintegrator has been confirmed in related industries. The results of the research can be used in the extraction of metals from tailings of metal-containing minerals at mining and processing enterprises of Ukraine, the Republic of Kazakhstan, the Republic of Kyrgyzstan and other developed mining countries of the world.
- Open Access
- 1 March 2025
- Published by Walter de Gruyter GmbH in Mining Revue
- Vol. 31 (1) , 88-99
Assessment of the Impact of the Uranium Industry on the Environment and Population
The paper provides an assessment of the impact of the uranium industry on the state of the environment and the population based on the development and implementation of engineering solutions and measures to reduce gamma radiation and radon concentration in the premises, the implementation of environmental and social rehabilitation of the contaminated territory, residential buildings, objects social sphere and the population living in the zone of influence of uranium facilities. The specified measures are aimed at improving the environmental safety of the environment and the population in order to minimize the negative impact of radiation and other factors. Used radiometric methods (measurement of the exposure dose and intensity of γ-radiation, measurement of the radioactivity of γ- and β-radiation, measurement of the power of the exposure dose of γ-radiation, determination of the power of the absorbed dose of γ-radiation in air, analysis of natural radionuclides (PRN); statistical and mathematical research methods using an integrated system approach Radioecological studies included: measurement of the exposure dose rate (PED) of γ-radiation by the network 100 x 10 m (walking survey) in the area of 40 km2, soil sampling for radium and uranium content, determination of radon concentration in residential premises specialists of various bodies of state power and local self-government in solving the above-mentioned tasks, for the regions located in the zone impact of mining and beneficiation plants for mining and primary processing of uranium ores. It was established that exceeding the normative level of the equivalent equilibrium concentration of radon of 50 Bq/m3 in individual rooms is caused by its release from the underground space and input channels of external heat and water supply networks, internal channels of distribution of heat networks. It has been proven that filling the heat network channel from the outside of the building with a layer of clay to a depth of 1 m and sealing it, sealing the entry of heat and water networks through the foundation of the building and concreting the pit reduce the volumetric activity of radon in the room by 5-6 times. The so far rare experience of increasing radiation and social protection of the population of the city of Zhovti Vody, Ukraine, which has been living in the zone of influence of uranium industry facilities for more than 70 years, is presented. It is proposed to continue research and provide funds (at the expense of enterprises, local and central state authorities) for conducting scientific substantiation and developing preventive measures to minimize the negative effects on human health from the action of heavy metals and radiation factors, taking into account the peculiarities of their combined impact on the population and workers of the uranium mining and mining and metallurgical industry.
- 1 March 2025
- Published by Walter de Gruyter GmbH in Mining Revue
- Vol. 31 (1) , 88-99
Open AccessAssessment of the Impact of the Uranium Industry on the Environment and Population
The paper provides an assessment of the impact of the uranium industry on the state of the environment and the population based on the development and implementation of engineering solutions and measures to reduce gamma radiation and radon concentration in the premises, the implementation of environmental and social rehabilitation of the contaminated territory, residential buildings, objects social sphere and the population living in the zone of influence of uranium facilities. The specified measures are aimed at improving the environmental safety of the environment and the population in order to minimize the negative impact of radiation and other factors. Used radiometric methods (measurement of the exposure dose and intensity of γ-radiation, measurement of the radioactivity of γ- and β-radiation, measurement of the power of the exposure dose of γ-radiation, determination of the power of the absorbed dose of γ-radiation in air, analysis of natural radionuclides (PRN); statistical and mathematical research methods using an integrated system approach Radioecological studies included: measurement of the exposure dose rate (PED) of γ-radiation by the network 100 x 10 m (walking survey) in the area of 40 km2, soil sampling for radium and uranium content, determination of radon concentration in residential premises specialists of various bodies of state power and local self-government in solving the above-mentioned tasks, for the regions located in the zone impact of mining and beneficiation plants for mining and primary processing of uranium ores. It was established that exceeding the normative level of the equivalent equilibrium concentration of radon of 50 Bq/m3 in individual rooms is caused by its release from the underground space and input channels of external heat and water supply networks, internal channels of distribution of heat networks. It has been proven that filling the heat network channel from the outside of the building with a layer of clay to a depth of 1 m and sealing it, sealing the entry of heat and water networks through the foundation of the building and concreting the pit reduce the volumetric activity of radon in the room by 5-6 times. The so far rare experience of increasing radiation and social protection of the population of the city of Zhovti Vody, Ukraine, which has been living in the zone of influence of uranium industry facilities for more than 70 years, is presented. It is proposed to continue research and provide funds (at the expense of enterprises, local and central state authorities) for conducting scientific substantiation and developing preventive measures to minimize the negative effects on human health from the action of heavy metals and radiation factors, taking into account the peculiarities of their combined impact on the population and workers of the uranium mining and mining and metallurgical industry.
- Open Access
- 26 December 2024
- Published by Kyiv National University of Construction and Architecture in Environmental safety and natural resources
- Vol. 52 (4) , 5-27
Improvement of combined technologies of underground block leaching of metals from out of balance and unconditioned ores
The object of the research is technologies and technical means for combined leaching of metals from hard ores in installations mounted in underground leaching blocks (BWB) with their preliminary crushing by explosives (BV). One of the most problematic places is the difficulty of achieving the specified quality of crushing, as well as the necessary height of ore storage in the chamber for further leaching of metals and the coefficient of loosening, taking into account the management of the energy of explosive destruction of rock ores. In the course of the study, the following were used: data from literary sources and patent documentation in the field of technologies and technical means for PBV of metals from ores in energy-disturbed massifs, substantiation of technological parameters of operational units; laboratory and production experiments; physical modeling of metal extraction from ores from the average linear size of a piece of blasted ore. Analytical studies, comparative analysis of theoretical and practical results using standard and new methods were performed with the participation of the authors. It was established that the most intense infiltration leaching occurs in the size class of ore pieces –100+0 mm. For the Michurynske deposit, Ukraine, during leaching, it is recommended that the yield of such a fraction in the reflected ore is about 90%. Metals are extracted less intensively and longer from fractions of –200+100 mm. It has been proven that the main place in PBV should be occupied by the explosive preparation of ore, which ensures effective extraction of metal from stored ores with a loosening coefficient of 1.15 > Kr < 1.20, which is regulated by the volume of ore released from the block (up to 30%) and parameters cameras (length, width and height). The extraction of metal ξ, %, which significantly depends on the average linear size of a piece of blasted ore dср and with a high degree of reliability (R2 = 0.97), was established. Due to the involvement in the production of substandard and off-balance ores, the raw material base of metal extraction at existing mines and those that are being built again can be increased by 1.4–1.6 times. Research results can be used during the underground development of ore deposits of off-balance and non-conditional ores of complex structure.
- 26 December 2024
- Published by Kyiv National University of Construction and Architecture in Environmental safety and natural resources
- Vol. 52 (4) , 5-27
Open AccessImprovement of combined technologies of underground block leaching of metals from out of balance and unconditioned ores
The object of the research is technologies and technical means for combined leaching of metals from hard ores in installations mounted in underground leaching blocks (BWB) with their preliminary crushing by explosives (BV). One of the most problematic places is the difficulty of achieving the specified quality of crushing, as well as the necessary height of ore storage in the chamber for further leaching of metals and the coefficient of loosening, taking into account the management of the energy of explosive destruction of rock ores. In the course of the study, the following were used: data from literary sources and patent documentation in the field of technologies and technical means for PBV of metals from ores in energy-disturbed massifs, substantiation of technological parameters of operational units; laboratory and production experiments; physical modeling of metal extraction from ores from the average linear size of a piece of blasted ore. Analytical studies, comparative analysis of theoretical and practical results using standard and new methods were performed with the participation of the authors. It was established that the most intense infiltration leaching occurs in the size class of ore pieces –100+0 mm. For the Michurynske deposit, Ukraine, during leaching, it is recommended that the yield of such a fraction in the reflected ore is about 90%. Metals are extracted less intensively and longer from fractions of –200+100 mm. It has been proven that the main place in PBV should be occupied by the explosive preparation of ore, which ensures effective extraction of metal from stored ores with a loosening coefficient of 1.15 > Kr < 1.20, which is regulated by the volume of ore released from the block (up to 30%) and parameters cameras (length, width and height). The extraction of metal ξ, %, which significantly depends on the average linear size of a piece of blasted ore dср and with a high degree of reliability (R2 = 0.97), was established. Due to the involvement in the production of substandard and off-balance ores, the raw material base of metal extraction at existing mines and those that are being built again can be increased by 1.4–1.6 times. Research results can be used during the underground development of ore deposits of off-balance and non-conditional ores of complex structure.
- Open Access
- 1 December 2024
- Published by Walter de Gruyter GmbH in Mining Revue
- Vol. 30 (4) , 32-43
Technologies and Technical Means for Electrosorption Leaching of Gold From Flotation Tailings of Resisting Sulfide Raw Materials
Relevance.: The problem of expanding the raw material base of the gold mining industry is becoming more pressing due to the depletion of explored reserves, rising production costs and the costs of minimizing the man-made impact on the environment. With the depletion of oxidized gold-bearing ores, finely disseminated ores are increasingly being involved in processing. An increase in gold production volumes can be achieved by improving the beneficiation process. An alternative to traditional beneficiation technologies is electrotechnologies that use the phenomenon of energy impact on mineral raw materials. Among them, the range of application of the resin-in-pulp electrosorption leaching technology is expanding. Objective.: Justification of technologies and technical means for electrosorption leaching of gold from flotation tailings of refractory sulfide raw materials. This will increase metal production and strengthen the mineral resource base of gold mining enterprises and reduce damage to the environment. Methodology.: A comprehensive method was applied, including analytical studies using the fundamentals of system analysis and mathematical statistics, technological experimentation using mathematical planning of experiments, economic and mathematical modeling, technical and economic calculations and pilot industrial implementation. Laboratory studies were modeled on the tailings of flotation enrichment of gold from the flotation tailings of refractory sulfide raw materials. The application of electric fields was provided by two parallel electrodes. Scientific novelty.: Theoretical and technological experimentation, substantiation of fundamentally new technologies and technical means of electrosorption leaching of gold from flotation tailings of refractory sulfide raw materials. Results.: The efficiency of using technogenic resources is achieved by combining traditional enrichment technologies with the capabilities of hydrometallurgy and electrochemistry. Flotation tailings of ores with gold content from 1.0-1.5 g/t are leached according to the scheme: granulation to a size of 15-30 mm with the addition of 1 g/l of cyanide, sulfuric acid removal of metals, alkaline treatment to pH 10-11, cyanidation with an irrigation density of 20 l/m 2 per hour, gold sorption on anion exchanger, anion exchanger regeneration and regenerate electrolysis. Gold leaching from refractory sulfide raw materials is possible after the destruction of sulfides upon reaching an oxidation potential of 1000 mV, it effectively proceeds in a solution of 20-30% sodium chloride upon application of direct electric current with a density of 800-1200 A/m 2 , pH of the medium 2.0-4.0 and a temperature of 60-800 C with the extraction of up to 70-80% of gold into the solution with an electric power consumption of 120-220 kW/t. The results of the experiment confirm the efficiency of the technology of electrosorption leaching of gold from gold-bearing pulps. The leaching rate increases by 25-30%, the sorption capacity of the anionite AM-2B increases by 2.5-3 times. An increase in the capacity of the sorbent and a decrease in the amount of gold in the liquid phase shifts the equilibrium of the system towards gold dissolution and intensifies the volume and completeness of its extraction. Implementation.: The technologies of electrosorption and electrochemical leaching of gold from ore flotation tailings have been tested and recommended for industrial development at the Aksu, Bestobe, Zholymbet deposits and implemented in the practice of ABS-Balkhash, Kazakhaltyn JSC (Republic of Kazakhstan) and can be recommended for other developed mining and gold mining countries of the world.
- 1 December 2024
- Published by Walter de Gruyter GmbH in Mining Revue
- Vol. 30 (4) , 32-43
Open AccessTechnologies and Technical Means for Electrosorption Leaching of Gold From Flotation Tailings of Resisting Sulfide Raw Materials
Relevance.: The problem of expanding the raw material base of the gold mining industry is becoming more pressing due to the depletion of explored reserves, rising production costs and the costs of minimizing the man-made impact on the environment. With the depletion of oxidized gold-bearing ores, finely disseminated ores are increasingly being involved in processing. An increase in gold production volumes can be achieved by improving the beneficiation process. An alternative to traditional beneficiation technologies is electrotechnologies that use the phenomenon of energy impact on mineral raw materials. Among them, the range of application of the resin-in-pulp electrosorption leaching technology is expanding. Objective.: Justification of technologies and technical means for electrosorption leaching of gold from flotation tailings of refractory sulfide raw materials. This will increase metal production and strengthen the mineral resource base of gold mining enterprises and reduce damage to the environment. Methodology.: A comprehensive method was applied, including analytical studies using the fundamentals of system analysis and mathematical statistics, technological experimentation using mathematical planning of experiments, economic and mathematical modeling, technical and economic calculations and pilot industrial implementation. Laboratory studies were modeled on the tailings of flotation enrichment of gold from the flotation tailings of refractory sulfide raw materials. The application of electric fields was provided by two parallel electrodes. Scientific novelty.: Theoretical and technological experimentation, substantiation of fundamentally new technologies and technical means of electrosorption leaching of gold from flotation tailings of refractory sulfide raw materials. Results.: The efficiency of using technogenic resources is achieved by combining traditional enrichment technologies with the capabilities of hydrometallurgy and electrochemistry. Flotation tailings of ores with gold content from 1.0-1.5 g/t are leached according to the scheme: granulation to a size of 15-30 mm with the addition of 1 g/l of cyanide, sulfuric acid removal of metals, alkaline treatment to pH 10-11, cyanidation with an irrigation density of 20 l/m 2 per hour, gold sorption on anion exchanger, anion exchanger regeneration and regenerate electrolysis. Gold leaching from refractory sulfide raw materials is possible after the destruction of sulfides upon reaching an oxidation potential of 1000 mV, it effectively proceeds in a solution of 20-30% sodium chloride upon application of direct electric current with a density of 800-1200 A/m 2 , pH of the medium 2.0-4.0 and a temperature of 60-800 C with the extraction of up to 70-80% of gold into the solution with an electric power consumption of 120-220 kW/t. The results of the experiment confirm the efficiency of the technology of electrosorption leaching of gold from gold-bearing pulps. The leaching rate increases by 25-30%, the sorption capacity of the anionite AM-2B increases by 2.5-3 times. An increase in the capacity of the sorbent and a decrease in the amount of gold in the liquid phase shifts the equilibrium of the system towards gold dissolution and intensifies the volume and completeness of its extraction. Implementation.: The technologies of electrosorption and electrochemical leaching of gold from ore flotation tailings have been tested and recommended for industrial development at the Aksu, Bestobe, Zholymbet deposits and implemented in the practice of ABS-Balkhash, Kazakhaltyn JSC (Republic of Kazakhstan) and can be recommended for other developed mining and gold mining countries of the world.
- Open Access
- 1 December 2024
- Published by Walter de Gruyter GmbH in Mining Revue
- Vol. 30 (4) , 44-55
Increasing the Efficiency of Titanium-Iron ORE Enrichment Through Using New Type Separators
The object of the research is technologies and technical means for selective destruction of mineral matrices of complex multicomponent titanium ores of primary deposits and beneficiation of minerals with altered magnetic properties. The aim of the work is to increase the efficiency of enrichment of titanium-iron ores by preliminary high-temperature treatment using new-type separators. This is achieved by substantiating the targeted selective destruction of mineral complexes and changing the magnetic properties of ore minerals as a result of temperature-controlled oxidation reactions. Methods of complex generalization, analysis and evaluation of practical experience and scientific achievements in the field of creation and introduction of new technologies and technical means for increase of efficiency of enrichment of titanium ores on the basis of separators of new type by substantiation of the directed selective destruction of mineral complexes and change of magnetic properties of ore minerals are described. It was found that for ilmenite, the main titanium component of raw materials, a low mass fraction of titanium is typical - no more than 30.0%, and ilmenite has lamellar-thin nano inclusions of hematite - 31.53 vol. %, which are difficult to remove from the ilmenite matrix. It is proved that in titanium-containing ores selective opening of splices occurs due to recrystallization of grains due to previous reduction, strengthening of bonds in hematiteilmenite contact zones and non-ore inclusions and creation of a network of germinal cracks inside nano splices due to exposure to mineral matrix. C. It is shown that the use of magnetic separation of raw materials after high-temperature treatment reduces the mass fraction of harmful elements such as silicon, aluminum and calcium oxides from 11.89 to 1.2% in the concentrate product and allows to increase the mass fraction of titanium oxide from 32.3 up to 37.6%, and total iron from 33.86 to 42.29%; The technology of complex ore beneficiation has been developed to provide concentrates used for the extraction of titanium slag (mass fraction of titanium oxide - 80-81.84%) and high-purity metallic iron Fe with an average chemical composition of Fe 0.993 Ti 0.006. The results of development and implementation of new generation technologies and separators in the enrichment and processing of titanium ore were obtained in the laboratories of the State Higher Educational Institution (KVUZ) "Kryvyi Rih National University" (Krivoy Rog, Ukraine) and implemented at the Public Joint Stock Company (PJSC) » (Zaporozhye, Ukraine) and the State Institute for the Design of Mining Enterprises SE" Krivbasproekt "(Krivoy Rog, Ukraine). The developed technologies are also the basis for the feasibility study of ore processing technology of the Abu Galaga field (Egypt), in the design of the industrial complex and can be useful for other enterprises in developed mining countries. Research and implementation of new technologies and technical means using dry magnetic separation will allow for the stable production of high-quality concentrates, as well as the reduction of the grinding and enrichment front by at least 15–20% of the original, which will reduce operating and capital costs by more than 30% and will become a powerful technological reserve for the development of mining production.
- 1 December 2024
- Published by Walter de Gruyter GmbH in Mining Revue
- Vol. 30 (4) , 44-55
Open AccessIncreasing the Efficiency of Titanium-Iron ORE Enrichment Through Using New Type Separators
The object of the research is technologies and technical means for selective destruction of mineral matrices of complex multicomponent titanium ores of primary deposits and beneficiation of minerals with altered magnetic properties. The aim of the work is to increase the efficiency of enrichment of titanium-iron ores by preliminary high-temperature treatment using new-type separators. This is achieved by substantiating the targeted selective destruction of mineral complexes and changing the magnetic properties of ore minerals as a result of temperature-controlled oxidation reactions. Methods of complex generalization, analysis and evaluation of practical experience and scientific achievements in the field of creation and introduction of new technologies and technical means for increase of efficiency of enrichment of titanium ores on the basis of separators of new type by substantiation of the directed selective destruction of mineral complexes and change of magnetic properties of ore minerals are described. It was found that for ilmenite, the main titanium component of raw materials, a low mass fraction of titanium is typical - no more than 30.0%, and ilmenite has lamellar-thin nano inclusions of hematite - 31.53 vol. %, which are difficult to remove from the ilmenite matrix. It is proved that in titanium-containing ores selective opening of splices occurs due to recrystallization of grains due to previous reduction, strengthening of bonds in hematiteilmenite contact zones and non-ore inclusions and creation of a network of germinal cracks inside nano splices due to exposure to mineral matrix. C. It is shown that the use of magnetic separation of raw materials after high-temperature treatment reduces the mass fraction of harmful elements such as silicon, aluminum and calcium oxides from 11.89 to 1.2% in the concentrate product and allows to increase the mass fraction of titanium oxide from 32.3 up to 37.6%, and total iron from 33.86 to 42.29%; The technology of complex ore beneficiation has been developed to provide concentrates used for the extraction of titanium slag (mass fraction of titanium oxide - 80-81.84%) and high-purity metallic iron Fe with an average chemical composition of Fe 0.993 Ti 0.006. The results of development and implementation of new generation technologies and separators in the enrichment and processing of titanium ore were obtained in the laboratories of the State Higher Educational Institution (KVUZ) "Kryvyi Rih National University" (Krivoy Rog, Ukraine) and implemented at the Public Joint Stock Company (PJSC) » (Zaporozhye, Ukraine) and the State Institute for the Design of Mining Enterprises SE" Krivbasproekt "(Krivoy Rog, Ukraine). The developed technologies are also the basis for the feasibility study of ore processing technology of the Abu Galaga field (Egypt), in the design of the industrial complex and can be useful for other enterprises in developed mining countries. Research and implementation of new technologies and technical means using dry magnetic separation will allow for the stable production of high-quality concentrates, as well as the reduction of the grinding and enrichment front by at least 15–20% of the original, which will reduce operating and capital costs by more than 30% and will become a powerful technological reserve for the development of mining production.
- Open Access
- 23 September 2024
- Published by Institute of Geological Sciences of the National Academy of Sciences of Ukraine in Geological Journal
- No. 3,p. 61-78
RESEARCH AND ASSESSMENT OF MINERAL RESERVES BASED ON AUTOMATED GEO-INFORMATION SYSTEM SUPPORT USING THE EXAMPLE OF THE NOVOKOSTIANTYNIV URANIUM ORE DEPOSIT
The article presents the scientific and practical results of research and assessment of mineral reserves based on automated geo-information system support using the example of the Novokostiantyniv uranium ore deposit. This will ensure the creation of databases of mining-geological and mining-technological conditions of mining operations with the use of computer graphics tools, which make it easier to detail the outline of the ore body by logging the fans of exploratory and explosive wells. It also makes it easier to manage the preparation of ore and metal reserves in it for mining. In the course of the study, data from literary sources and documentation in the field of underground development of ore deposits of complex structure were used. Classical clustering methods were used for data selection. The most practical is the method of inverse weighted distances, spine, trend, kriking, etc. The methods of mathematical statistics, correlation methods, determination of difference equations using the Wiener–Hopf equation, classic and new methods of multi-link systems with the participation of the authors were used in the creation of models. It has been proven that in the contour zone of the chamber, the coefficients of ore desalting reach 60–70% of the total values, and on average they are 29–32% for the operational block. Reserve coefficients are set, taking into account the verifiability of ore reserves (1.10) and metal in it (1.05). The general reserve coefficient (its value is in the range of 1.30–1.45) for rational use and protection of the subsoil during the development of deposits of a complex structure is substantiated. It is shown that the total reserve coefficient should take into account not only the technological reliability of the mine for the extraction of ore and metal in it, but also the verifiability of subsoil reserves. In particular, the values of readiness of reserves for extraction are determined by ore, differ by 10–15% from similar values for metal, and the indicators of extraction of minerals from the subsoil – from the characteristics of the elements of ore deposits (loss and depletion coefficients for metal are about 75%, similar indicators determined by ore). On the basis of the received data, albums-catalogues, methods for them were compiled, specialized computer modules based on K-MINE® GIS were developed. The proposed graph-analytical, tabular and computer calculation methods simplify the management and control of extraction of mineral reserves from the subsoil. The Derzhhirpromnahlyad “Instructions on rationing of ore reserves, prepared and ready for extraction at the Novokostyantinivska mine” of the State Enterprise “Skhidnyi GZK” was developed and agreed upon. Geophysical devices and systems with RAM simplify data entry into the computer database using special programs such as Surfer or GIS K-MINE®, VENTSIM, etc. Their implementation with the help of the automated system of geological and economic assessment (AT GEO) GIS K-MINE® makes it easier to solve applied questions of GEO of reserves of mineral deposits. The obtained results of the research allow to determine, optimize and control losses and depletion of ore and metal in it due to the establishment of the optimal contour of ore reflection in the contour zone, as well as to effectively manage ore reserves prepared and ready for extraction during the development of deposits of complex structure, which are, in particular, uranium deposits.
- 23 September 2024
- Published by Institute of Geological Sciences of the National Academy of Sciences of Ukraine in Geological Journal
- No. 3,p. 61-78
Open AccessRESEARCH AND ASSESSMENT OF MINERAL RESERVES BASED ON AUTOMATED GEO-INFORMATION SYSTEM SUPPORT USING THE EXAMPLE OF THE NOVOKOSTIANTYNIV URANIUM ORE DEPOSIT
The article presents the scientific and practical results of research and assessment of mineral reserves based on automated geo-information system support using the example of the Novokostiantyniv uranium ore deposit. This will ensure the creation of databases of mining-geological and mining-technological conditions of mining operations with the use of computer graphics tools, which make it easier to detail the outline of the ore body by logging the fans of exploratory and explosive wells. It also makes it easier to manage the preparation of ore and metal reserves in it for mining. In the course of the study, data from literary sources and documentation in the field of underground development of ore deposits of complex structure were used. Classical clustering methods were used for data selection. The most practical is the method of inverse weighted distances, spine, trend, kriking, etc. The methods of mathematical statistics, correlation methods, determination of difference equations using the Wiener–Hopf equation, classic and new methods of multi-link systems with the participation of the authors were used in the creation of models. It has been proven that in the contour zone of the chamber, the coefficients of ore desalting reach 60–70% of the total values, and on average they are 29–32% for the operational block. Reserve coefficients are set, taking into account the verifiability of ore reserves (1.10) and metal in it (1.05). The general reserve coefficient (its value is in the range of 1.30–1.45) for rational use and protection of the subsoil during the development of deposits of a complex structure is substantiated. It is shown that the total reserve coefficient should take into account not only the technological reliability of the mine for the extraction of ore and metal in it, but also the verifiability of subsoil reserves. In particular, the values of readiness of reserves for extraction are determined by ore, differ by 10–15% from similar values for metal, and the indicators of extraction of minerals from the subsoil – from the characteristics of the elements of ore deposits (loss and depletion coefficients for metal are about 75%, similar indicators determined by ore). On the basis of the received data, albums-catalogues, methods for them were compiled, specialized computer modules based on K-MINE® GIS were developed. The proposed graph-analytical, tabular and computer calculation methods simplify the management and control of extraction of mineral reserves from the subsoil. The Derzhhirpromnahlyad “Instructions on rationing of ore reserves, prepared and ready for extraction at the Novokostyantinivska mine” of the State Enterprise “Skhidnyi GZK” was developed and agreed upon. Geophysical devices and systems with RAM simplify data entry into the computer database using special programs such as Surfer or GIS K-MINE®, VENTSIM, etc. Their implementation with the help of the automated system of geological and economic assessment (AT GEO) GIS K-MINE® makes it easier to solve applied questions of GEO of reserves of mineral deposits. The obtained results of the research allow to determine, optimize and control losses and depletion of ore and metal in it due to the establishment of the optimal contour of ore reflection in the contour zone, as well as to effectively manage ore reserves prepared and ready for extraction during the development of deposits of complex structure, which are, in particular, uranium deposits.
- Open Access
- 23 September 2024
- Published by Ukrainian Geological Company in Мінеральні ресурси України
- No. 3,p. 78-85
Обґрунтування ефективності охорони надр та екологічної безпеки під час розробки приповерхневих запасів рудних родовищ
Викладені головні наукові та практичні результати обґрунтування ефективності охорони надр та екологічної безпеки під час розробки приповерхневих запасів рудних родовищ камерними системами із заповненням порожнин твердючою сумішшю під об’єктами, що охороняються, на глибині 150–200 м від денної поверхні з урахуванням сейсмічної та екологічної безпеки і соціального фактора, які реалізовані в інструкціях, стандартах і практиці роботи рудних шахт України. Проведення означених заходів дозволяє забезпечити максимальне вилучення руди, надійне збереження об’єктів, що охороняються, і зниження проникнення небезпечних речовин на земну поверхню.Встановлені параметри гранично стійких еквівалентних прольотів горизонтальних оголень стелини камер з урахуванням властивості гірського масиву, часу стояння, глибини розташування і технології утворення камер у діапазоні глибин 45–210 м під час відпрацювання рудних родовищ ДП “СхідГЗК” (Україна) під об’єктами, що охороняються. Для забезпечення запропонованих мінімально допустимих, за умовами стійкості, параметрів стелини доцільно зміцнювати гірські породи розробленими інженерними методами, які дозволяють зберегти денну поверхню під об’єктами, що охороняються, і виключити вихід забруднюючих речовин на поверхню та оточуюче навколишнє середовище.Запропоновано також метод зустрічно-направленого ініціювання зарядів у суміжних свердловинах, що позитивно впливає на стійкість стелини за рахунок зниження динамічної дії вибуху. Обґрунтовано, що при зустрічно-направленому ініціюванні із застосуванням неелектричних засобів підривання свердловинних зарядів вихід негабариту (νн) зменшується і знаходиться в експоненційній залежності від лінії найменшого опору (W) типу νн = 5,57 × е0,022W. Це дозволяє збільшити вагу зарядів вибухових речовин на одне уповільнення в межах віяла свердловин від 300 до 1250 кг та знизити швидкість сейсмічних коливань масиву стелини від 0,46 до 0,28 см/с. На погляд авторів, було б корисно розробити нормативно-методичний документ “Рекомендації щодо розвитку дистанційного радіаційного моніторингу довкілля в районах розміщення об’єктів атомної промисловості”, в яких надати вимоги до моніторингу повітряного, водного середовища, ґрунтів тощо.
- 23 September 2024
- Published by Ukrainian Geological Company in Мінеральні ресурси України
- No. 3,p. 78-85
Open AccessОбґрунтування ефективності охорони надр та екологічної безпеки під час розробки приповерхневих запасів рудних родовищ
Викладені головні наукові та практичні результати обґрунтування ефективності охорони надр та екологічної безпеки під час розробки приповерхневих запасів рудних родовищ камерними системами із заповненням порожнин твердючою сумішшю під об’єктами, що охороняються, на глибині 150–200 м від денної поверхні з урахуванням сейсмічної та екологічної безпеки і соціального фактора, які реалізовані в інструкціях, стандартах і практиці роботи рудних шахт України. Проведення означених заходів дозволяє забезпечити максимальне вилучення руди, надійне збереження об’єктів, що охороняються, і зниження проникнення небезпечних речовин на земну поверхню.Встановлені параметри гранично стійких еквівалентних прольотів горизонтальних оголень стелини камер з урахуванням властивості гірського масиву, часу стояння, глибини розташування і технології утворення камер у діапазоні глибин 45–210 м під час відпрацювання рудних родовищ ДП “СхідГЗК” (Україна) під об’єктами, що охороняються. Для забезпечення запропонованих мінімально допустимих, за умовами стійкості, параметрів стелини доцільно зміцнювати гірські породи розробленими інженерними методами, які дозволяють зберегти денну поверхню під об’єктами, що охороняються, і виключити вихід забруднюючих речовин на поверхню та оточуюче навколишнє середовище.Запропоновано також метод зустрічно-направленого ініціювання зарядів у суміжних свердловинах, що позитивно впливає на стійкість стелини за рахунок зниження динамічної дії вибуху. Обґрунтовано, що при зустрічно-направленому ініціюванні із застосуванням неелектричних засобів підривання свердловинних зарядів вихід негабариту (νн) зменшується і знаходиться в експоненційній залежності від лінії найменшого опору (W) типу νн = 5,57 × е0,022W. Це дозволяє збільшити вагу зарядів вибухових речовин на одне уповільнення в межах віяла свердловин від 300 до 1250 кг та знизити швидкість сейсмічних коливань масиву стелини від 0,46 до 0,28 см/с. На погляд авторів, було б корисно розробити нормативно-методичний документ “Рекомендації щодо розвитку дистанційного радіаційного моніторингу довкілля в районах розміщення об’єктів атомної промисловості”, в яких надати вимоги до моніторингу повітряного, водного середовища, ґрунтів тощо.
- Open Access
- 1 September 2024
- Published by Walter de Gruyter GmbH in Mining Revue
- Vol. 30 (3) , 30-42
Evaluation of Technologies and Technical Means for Using the Phenomenon of Natural Bischofite in the Field of Mining Industry and Ecology
Goal: Evaluation of technologies and technical means for the use of the phenomenon of the aqueous solution of natural bischophyte (RPB) in various branches of the national economy, in particular, the mining and mineral industry, ecology and medicine. Their use will improve the economic efficiency and environmental safety of the processes of blasting rock mass in quarries and storing waste from enrichment of ore raw materials in tailings storage facilities, freezing and freezing of ore mass during its transportation to enrichment plants. Research methods: During the study, systematization, and generalization of technologies and technical means of using RPB, the analysis of research and publications, the results of industrial and experimental research at landfills using standard and new methods with the participation of authors and leading specialists in the specified fields were used. Scientific novelty: The main scientific, practical and social results of the assessment of technologies and technical means for the use of the phenomenon of water RPB in various sectors of the national economy, in particular, in the mining industry, ecology and medicine, are given. The functional dependence between the freezing temperature of the mining mass (t с , °С) and the content of the aqueous solution of natural bischofite in it (С b , %) was established. Practical significance: The technology to prevent winter slippage on quarry roads using RPB has been developed and implemented. Recommendations are given for combating the release of dust during the transportation of rock mass by rail transport, during mass explosions in quarries, on quarry highways and on tailings piles of GZK, with the use of RPB and bitumen emulsion, which allow to effectively fix dust surfaces from blowing dust. To reduce dust emission into the atmosphere during mass blasts in quarries, it is proposed to wet the surface of drilling dust with RPB with a density of 1250 - 1270 kg / m 3 and a consumption of 4.5 - 5.0 l / m 2 . The results: When using RPB instead of water during blasting operations in quarries, BP costs are reduced by 1.4-1.5 times and emissions of harmful gases during blasting are reduced by 20-30%. In underground mining operations, when water is replaced with RPB for moistening BP granules, the release of gases during a mass explosion in the mine is reduced by 1.3-1.4 times. To prevent freezing or freezing of rock mass to the inner surface of open wagons during transportation in the cold, preventive treatment of the inner surface of RPB railway wagons is carried out. In order to prevent ice on highways in quarries, they are also pre-treated with RPB. The technology of preventing winter slippage and dusting of quarry roads with RPB reagents with the use of watering machines was developed and implemented in the conditions of PJSC "Southern GZK" (Kryvbas, Ukraine). Recommendations for fighting dust on highways, landfills and tailings storage facilities of GZK, using RPB and bitumen emulsion, which allow to effectively fix dusty surfaces from blowing dust, using specially developed equipment, are given. In particular, the cost of processing ragweed RPB with an average overgrowth density of 5.0 kg/m 2 at the current cost of the solution of UAH 960/ton does not exceed UAH 40 per 100 m 2 (acre). One of the promising areas of further research is the use of large volumes of man-made underground cavities, formed during the leaching of bischofite, for the storage of useful liquid substances or for the disposal of waste at a depth of more than 1500 m.
- 1 September 2024
- Published by Walter de Gruyter GmbH in Mining Revue
- Vol. 30 (3) , 30-42
Open AccessEvaluation of Technologies and Technical Means for Using the Phenomenon of Natural Bischofite in the Field of Mining Industry and Ecology
Goal: Evaluation of technologies and technical means for the use of the phenomenon of the aqueous solution of natural bischophyte (RPB) in various branches of the national economy, in particular, the mining and mineral industry, ecology and medicine. Their use will improve the economic efficiency and environmental safety of the processes of blasting rock mass in quarries and storing waste from enrichment of ore raw materials in tailings storage facilities, freezing and freezing of ore mass during its transportation to enrichment plants. Research methods: During the study, systematization, and generalization of technologies and technical means of using RPB, the analysis of research and publications, the results of industrial and experimental research at landfills using standard and new methods with the participation of authors and leading specialists in the specified fields were used. Scientific novelty: The main scientific, practical and social results of the assessment of technologies and technical means for the use of the phenomenon of water RPB in various sectors of the national economy, in particular, in the mining industry, ecology and medicine, are given. The functional dependence between the freezing temperature of the mining mass (t с , °С) and the content of the aqueous solution of natural bischofite in it (С b , %) was established. Practical significance: The technology to prevent winter slippage on quarry roads using RPB has been developed and implemented. Recommendations are given for combating the release of dust during the transportation of rock mass by rail transport, during mass explosions in quarries, on quarry highways and on tailings piles of GZK, with the use of RPB and bitumen emulsion, which allow to effectively fix dust surfaces from blowing dust. To reduce dust emission into the atmosphere during mass blasts in quarries, it is proposed to wet the surface of drilling dust with RPB with a density of 1250 - 1270 kg / m 3 and a consumption of 4.5 - 5.0 l / m 2 . The results: When using RPB instead of water during blasting operations in quarries, BP costs are reduced by 1.4-1.5 times and emissions of harmful gases during blasting are reduced by 20-30%. In underground mining operations, when water is replaced with RPB for moistening BP granules, the release of gases during a mass explosion in the mine is reduced by 1.3-1.4 times. To prevent freezing or freezing of rock mass to the inner surface of open wagons during transportation in the cold, preventive treatment of the inner surface of RPB railway wagons is carried out. In order to prevent ice on highways in quarries, they are also pre-treated with RPB. The technology of preventing winter slippage and dusting of quarry roads with RPB reagents with the use of watering machines was developed and implemented in the conditions of PJSC "Southern GZK" (Kryvbas, Ukraine). Recommendations for fighting dust on highways, landfills and tailings storage facilities of GZK, using RPB and bitumen emulsion, which allow to effectively fix dusty surfaces from blowing dust, using specially developed equipment, are given. In particular, the cost of processing ragweed RPB with an average overgrowth density of 5.0 kg/m 2 at the current cost of the solution of UAH 960/ton does not exceed UAH 40 per 100 m 2 (acre). One of the promising areas of further research is the use of large volumes of man-made underground cavities, formed during the leaching of bischofite, for the storage of useful liquid substances or for the disposal of waste at a depth of more than 1500 m.