Ramesh Rudrapati
Ramesh Rudrapati has a total of 38 co-authors. Here are the top co-authors by number of shared publications:
- Asish Bandyopadhyay
Jadavpur University
2 shared publications - D. Harsha Vardhan
PVKK Institute of Technology
2 shared publications Lakhan Rathod
JSPM’s BSIOTR
2 shared publications- Pradip Kumar Pal
Jadavpur University
2 shared publications - Rohinikumar Chebolu
Department of Mechanical Engineering, A.U. College of Engineering(A), Andhra University, Visakhapatnam, Andhra Pradesh, India
2 shared publications Y. Santhosh Kumar Reddy
Department of Mechanical Engineering
2 shared publications
Latest Publications
- 12 December 2024
- Published by Wiley in Energy Storage
- Vol. 6 (8)
Parametric Investigation to Assess the Charging and Discharging Time for a Latent Heat Storage Material‐Based Thermal Energy Storage System for Concentrated Solar Power Plants
Thermal energy storage (TES) systems are becoming increasingly crucial as viable alternatives for effective energy utilization from various sources, such as solar power plants and waste heat from different industrial sectors. The present work focuses on latent heat TES system optimization for solar thermal power plant applications. This study aims to assess the impact of different thermal processing factors on the efficiency of TES systems. Parametric analysis determines a TES system's charging and discharging durations that use latent heat storage material. Thermal processing conditions were selected as input parameters, such as the heat transfer fluid inlet temperature, flow rate, and number of phase change material (PCM) capsules. Experiments were planned to use the L9 orthogonal array of the Taguchi method, and response measures, such as charging time (CT) and discharging time (DT), were monitored. A signal‐to‐noise ratio analysis was used to evaluate the significance of the thermal processing parameters on the response measures. Response surface methodology (RSM) postulates the mathematical relationships between process conditions and responses. Finally, the multi‐objective Jaya optimization algorithm (MOJOA) was used to optimize the parametric combination to minimize CT and maximize DT simultaneously. A heat transfer fluid inlet temperature of 65°C, flow rate of 2 L/min, and 40 PCM capsules were determined as the optimal parametric conditions by MOJOA for predicting the combined CT and DT. The verification test results substantiate the enhanced responses of the latent heat TES system, specifically in the CT and DT. Utilizing the integrated Taguchi method, RSM‐MOJOA is advantageous for examining, modeling, and predicting PCM‐based TES systems.
- 12 December 2024
- Published by Wiley in Energy Storage
- Vol. 6 (8)
Parametric Investigation to Assess the Charging and Discharging Time for a Latent Heat Storage Material‐Based Thermal Energy Storage System for Concentrated Solar Power Plants
Thermal energy storage (TES) systems are becoming increasingly crucial as viable alternatives for effective energy utilization from various sources, such as solar power plants and waste heat from different industrial sectors. The present work focuses on latent heat TES system optimization for solar thermal power plant applications. This study aims to assess the impact of different thermal processing factors on the efficiency of TES systems. Parametric analysis determines a TES system's charging and discharging durations that use latent heat storage material. Thermal processing conditions were selected as input parameters, such as the heat transfer fluid inlet temperature, flow rate, and number of phase change material (PCM) capsules. Experiments were planned to use the L9 orthogonal array of the Taguchi method, and response measures, such as charging time (CT) and discharging time (DT), were monitored. A signal‐to‐noise ratio analysis was used to evaluate the significance of the thermal processing parameters on the response measures. Response surface methodology (RSM) postulates the mathematical relationships between process conditions and responses. Finally, the multi‐objective Jaya optimization algorithm (MOJOA) was used to optimize the parametric combination to minimize CT and maximize DT simultaneously. A heat transfer fluid inlet temperature of 65°C, flow rate of 2 L/min, and 40 PCM capsules were determined as the optimal parametric conditions by MOJOA for predicting the combined CT and DT. The verification test results substantiate the enhanced responses of the latent heat TES system, specifically in the CT and DT. Utilizing the integrated Taguchi method, RSM‐MOJOA is advantageous for examining, modeling, and predicting PCM‐based TES systems.
- Open Access
- 14 April 2023
- Published by Wiley in Advances in Materials Science and Engineering
- Vol. 2023, 1-7
Experimental Studies on Mechanical Behavior of TIG and Friction Stir Welded AA5083 -AA7075 Dissimilar Aluminum Alloys
Welding is a suitable and better process to manufacture complex objects for aerospace, naval, and automotive structures. Service conditions and complexity in load acting force the manufactures to make joints between dissimilar materials. Thus, there is a need for efficient welding techniques to form sound joints and an understanding of imperfections and their effects. In this study an attempt has been made to study the joining feasibility of dissimilar aluminum alloys by two different welding techniques, namely, tungsten inert gas welding (TIG) and friction stir welding (FSW). Dissimilar AA5083-O and AA7075-T651 aluminum alloys successfully joined by considered welding techniques. Metallurgical and mechanical characteristics of fabricated weld joints are studied at different weld currents (80–120 amp) for TIG and various rotational speeds (800, 1000, 1100, 1200, and 1400 rpm) with constant traverse speed for FSW. Weld joints made by FSW exhibit superior tensile strength, whereas the joint line microhardness of TIG samples is higher than the FSW ones.
- 14 April 2023
- Published by Wiley in Advances in Materials Science and Engineering
- Vol. 2023, 1-7
Open AccessExperimental Studies on Mechanical Behavior of TIG and Friction Stir Welded AA5083 -AA7075 Dissimilar Aluminum Alloys
Welding is a suitable and better process to manufacture complex objects for aerospace, naval, and automotive structures. Service conditions and complexity in load acting force the manufactures to make joints between dissimilar materials. Thus, there is a need for efficient welding techniques to form sound joints and an understanding of imperfections and their effects. In this study an attempt has been made to study the joining feasibility of dissimilar aluminum alloys by two different welding techniques, namely, tungsten inert gas welding (TIG) and friction stir welding (FSW). Dissimilar AA5083-O and AA7075-T651 aluminum alloys successfully joined by considered welding techniques. Metallurgical and mechanical characteristics of fabricated weld joints are studied at different weld currents (80–120 amp) for TIG and various rotational speeds (800, 1000, 1100, 1200, and 1400 rpm) with constant traverse speed for FSW. Weld joints made by FSW exhibit superior tensile strength, whereas the joint line microhardness of TIG samples is higher than the FSW ones.
- 1 January 2023
- Published by AIP Publishing in AIP Conference Proceedings
- Vol. 2605 (1) , 020001
Surface roughness prediction in VMC five axis machining of EN 47 steel by RSM and DFA
Milling is very often used metal removal processes for industrial applications. Vertical machining center five - axis (VMC–5-axis) is innovative metal cutting machine, used to perform milling operation which relies on rotary cutters to remove unwanted metal from a workpiece. VMC works based on the concept of vertical milling machine which employs a spindle with a vertical orientation. Because of high cost of the machining setup, machining operations in this process can be performed optimum manner to get economical advantage. Input parameters selection plays critical role in VMC-5-axis to get the machining economics. Surface roughness of any milled part is highly depending on correct selection of process parameters. In the present research, investigational based laboratory analysis has been prepared to examine the implications of milling processing condition(s) on quality measure, surface finish of EN47 steel. The experimental tests have been planned as per response surface methodology (RSM). Mathematical relations between the operating conditions and surface roughness are developed by using RSM. Three-dimensional surface plots had been developed to explore the factor effects on surface roughness. From the surface plots, it is found that process parameters are highly significant for surface quality of EN47 steel. The optimum parametric condition was obtained by desirability function approach (DFA). The factor effects on surface finish have been identified by analysis of variance. The concluding observations has been derived from proposed research investigation.
- 1 January 2023
- Published by AIP Publishing in AIP Conference Proceedings
- Vol. 2605 (1) , 020001
Surface roughness prediction in VMC five axis machining of EN 47 steel by RSM and DFA
Milling is very often used metal removal processes for industrial applications. Vertical machining center five - axis (VMC–5-axis) is innovative metal cutting machine, used to perform milling operation which relies on rotary cutters to remove unwanted metal from a workpiece. VMC works based on the concept of vertical milling machine which employs a spindle with a vertical orientation. Because of high cost of the machining setup, machining operations in this process can be performed optimum manner to get economical advantage. Input parameters selection plays critical role in VMC-5-axis to get the machining economics. Surface roughness of any milled part is highly depending on correct selection of process parameters. In the present research, investigational based laboratory analysis has been prepared to examine the implications of milling processing condition(s) on quality measure, surface finish of EN47 steel. The experimental tests have been planned as per response surface methodology (RSM). Mathematical relations between the operating conditions and surface roughness are developed by using RSM. Three-dimensional surface plots had been developed to explore the factor effects on surface roughness. From the surface plots, it is found that process parameters are highly significant for surface quality of EN47 steel. The optimum parametric condition was obtained by desirability function approach (DFA). The factor effects on surface finish have been identified by analysis of variance. The concluding observations has been derived from proposed research investigation.
- Open Access
- 17 August 2022
- Published by Wiley in Journal of Engineering
- Vol. 2022, 1-5
Influence of SiC/TiB2 Particles Addition on Corrosion Behavior of As-Cast Zn-Al-Cu Alloy Hybrid Composites
In this work, the silicon carbide (SiC) and titanium diboride (TiB2) reinforced as-cast Zn-Al-Cu alloy-based hybrid composites were produced with ultrasonic-assisted stir casting. The corrosion behavior of as-cast Zn-Al-Cu/TiB2/SiC hybrid composites with varying 0, 5, 10, and 15 weight percent of SiC+TiB2 particulates in Zn-Al-Cu matrix alloy was investigated in this study, The effect of additional reinforcements content on the corrosion behavior of hybrid composites with respect to Zn-Al-Cu alloy was investigated. The corrosion rate of hybrid composites was taken by using potentiodynamic polarization equipment (with 3.5 wt. NaCl solution). The potentiodynamic polarization test findings showed that the hybrid composites uniform and localized corrosion resistances were enhanced by the addition of dual reinforcements. As the weight fraction of the SiC/TiB2 reinforcement increases, weak microgalvanic cells that form between the constituent phases of the fabricated as-cast Zn-Al-Cu hybrid composites weaken, improving their resistance to uniform and localized corrosion. The results revealed that the corrosion rate values were reduced to 28.88 at 15 of reinforcement when compared to the base alloy.
- 17 August 2022
- Published by Wiley in Journal of Engineering
- Vol. 2022, 1-5
Open AccessInfluence of SiC/TiB2 Particles Addition on Corrosion Behavior of As-Cast Zn-Al-Cu Alloy Hybrid Composites
In this work, the silicon carbide (SiC) and titanium diboride (TiB2) reinforced as-cast Zn-Al-Cu alloy-based hybrid composites were produced with ultrasonic-assisted stir casting. The corrosion behavior of as-cast Zn-Al-Cu/TiB2/SiC hybrid composites with varying 0, 5, 10, and 15 weight percent of SiC+TiB2 particulates in Zn-Al-Cu matrix alloy was investigated in this study, The effect of additional reinforcements content on the corrosion behavior of hybrid composites with respect to Zn-Al-Cu alloy was investigated. The corrosion rate of hybrid composites was taken by using potentiodynamic polarization equipment (with 3.5 wt. NaCl solution). The potentiodynamic polarization test findings showed that the hybrid composites uniform and localized corrosion resistances were enhanced by the addition of dual reinforcements. As the weight fraction of the SiC/TiB2 reinforcement increases, weak microgalvanic cells that form between the constituent phases of the fabricated as-cast Zn-Al-Cu hybrid composites weaken, improving their resistance to uniform and localized corrosion. The results revealed that the corrosion rate values were reduced to 28.88 at 15 of reinforcement when compared to the base alloy.
- Open Access
- 20 May 2022
- Published by Wolters Kluwer Health in Annals of Medicine & Surgery
- Vol. 78, 103811
Using industrial 4.0 technologies to combat the COVID-19 pandemic
The COVID 19 (Coronavirus) pandemic has led to a surge in the demand for healthcare devices, pre-cautions, or medicines along with advanced information technology. It has become a global mission to control the Coronavirus to prevent the death of innocent people. The fourth industrial revolution (I4.0) is a new approach to thinking that is proposed across a wide range of industries and services to achieve greater success and quality of life. Several initiatives associated with industry 4.0 are expected to make a difference in the fight against COVID-19. Implementing I4.0 components effectively could lead to a reduction in barriers between patients and healthcare workers and could result in improved communication between them. The present study aims to review the components of I4.0 and related tools used to combat the Coronavirus. This article highlights the benefits of each component of the I4.0, which is useful in controlling the spread of COVID-19. From the present study, it is stated that I4.0 technologies could provide an effective solution to deal with local as well as global medical crises in an innovative way.
- 20 May 2022
- Published by Wolters Kluwer Health in Annals of Medicine & Surgery
- Vol. 78, 103811
Open AccessUsing industrial 4.0 technologies to combat the COVID-19 pandemic
The COVID 19 (Coronavirus) pandemic has led to a surge in the demand for healthcare devices, pre-cautions, or medicines along with advanced information technology. It has become a global mission to control the Coronavirus to prevent the death of innocent people. The fourth industrial revolution (I4.0) is a new approach to thinking that is proposed across a wide range of industries and services to achieve greater success and quality of life. Several initiatives associated with industry 4.0 are expected to make a difference in the fight against COVID-19. Implementing I4.0 components effectively could lead to a reduction in barriers between patients and healthcare workers and could result in improved communication between them. The present study aims to review the components of I4.0 and related tools used to combat the Coronavirus. This article highlights the benefits of each component of the I4.0, which is useful in controlling the spread of COVID-19. From the present study, it is stated that I4.0 technologies could provide an effective solution to deal with local as well as global medical crises in an innovative way.
- Open Access
- 19 April 2022
- Published by Elsevier in Composites Part C: Open Access
- Vol. 8
Effects of welding process conditions on friction stir welding of polymer composites: A review
- 19 April 2022
- Published by Elsevier in Composites Part C: Open Access
- Vol. 8
Open AccessEffects of welding process conditions on friction stir welding of polymer composites: A review
- 1 January 2022
- Published by Springer Nature
- p. 945-953
Minimization of Surface Roughness of WEDM’ed H13 Tool Steel Using Taguchi Method
- 1 January 2022
- Published by Springer Nature
- p. 945-953
Minimization of Surface Roughness of WEDM’ed H13 Tool Steel Using Taguchi Method
- RetractedOpen Access
- 1 January 2021
- Published by Wiley in Advances in Materials Science and Engineering
- Vol. 2021 (1)
[Retracted] Experimental Study of Thermal and Mechanical Behaviour of Graphite‐Filled UJF Composite
The advancement of composites mixed with natural fibers and with fillers has become the most supportable alternative material for engineering applications, especially in industries such as automotive and aerospace. Natural fibers are renewable, cheap, biodegradable, and ecological materials. In the present work, already used woven jute fibers, which are extracted from gunny bags with the same grams per square meter (GSM), were used, and then, woven jute fibers were chemically treated to improve their characteristics. Graphite powder‐filled used jute fiber reinforced epoxy composite (UJF) are prepared by using the hand‐layup technique. Tests such as tensile, flexure, impact, and thermo‐gravimetric analysis (TGA) were conducted. These tests were according to ASTM standards to evaluate the effect of graphite filler content on hybrid epoxy jute composites. The composite material is prepared by changing the content by weight of the filler by 3%, 6%, 9%, and 12%. The experimental results reveal that 6% of the graphite composites showed the maximum tensile strength and modulus. With the increase in the filler content, there is a decrease in the flexural properties. The impact resistance increases slightly up to 6% of the filler content. The study of thermal decomposition showed that the lowest mass loss was found at 9% by weight of the filler content. Morphological analysis performed by FE‐SEM showed that the addition of filler content improved the binding of the fiber and matrix up to 6% by weight of the filler content. It should be noted that these hybrid composites are a promising material at low cost for lightweight structural applications.
- 1 January 2021
- Published by Wiley in Advances in Materials Science and Engineering
- Vol. 2021 (1)
RetractedOpen Access[Retracted] Experimental Study of Thermal and Mechanical Behaviour of Graphite‐Filled UJF Composite
The advancement of composites mixed with natural fibers and with fillers has become the most supportable alternative material for engineering applications, especially in industries such as automotive and aerospace. Natural fibers are renewable, cheap, biodegradable, and ecological materials. In the present work, already used woven jute fibers, which are extracted from gunny bags with the same grams per square meter (GSM), were used, and then, woven jute fibers were chemically treated to improve their characteristics. Graphite powder‐filled used jute fiber reinforced epoxy composite (UJF) are prepared by using the hand‐layup technique. Tests such as tensile, flexure, impact, and thermo‐gravimetric analysis (TGA) were conducted. These tests were according to ASTM standards to evaluate the effect of graphite filler content on hybrid epoxy jute composites. The composite material is prepared by changing the content by weight of the filler by 3%, 6%, 9%, and 12%. The experimental results reveal that 6% of the graphite composites showed the maximum tensile strength and modulus. With the increase in the filler content, there is a decrease in the flexural properties. The impact resistance increases slightly up to 6% of the filler content. The study of thermal decomposition showed that the lowest mass loss was found at 9% by weight of the filler content. Morphological analysis performed by FE‐SEM showed that the addition of filler content improved the binding of the fiber and matrix up to 6% by weight of the filler content. It should be noted that these hybrid composites are a promising material at low cost for lightweight structural applications.
- RetractedOpen Access
- 1 January 2021
- Published by Wiley in Advances in Materials Science and Engineering
- Vol. 2021 (1)
[Retracted] Effect of Grey and White Portland Cement Fillers on Flexural and Shear Strength of GFRP Composite Material
The mechanical behaviour of glass fiber reinforced polymer (GFRP) composite depends on the type of matrix, filler, and fiber architecture. In order to develop high‐strength polymer matrix composites, the composites containing 5%, 10%, and 15% each of Portland grey and white cement filler are prepared by uniformly mixing the epoxy and filler materials, followed by casting by hand layup technique. The flexural and shear test is performed in accordance with ASTM 790 and ASTM D5379, respectively. It has been found that the values of shear strength, flexural strength, and modulus of elasticity vary with the increasing amount of cement component in the polymer. In addition, for a given percentage of the components of the cementitious filler, the values of the mechanical strength of the composites that contain white cement are higher than those of the composites that contain grey cement filler. Damage to composites has been found to involve fiber breakage and delamination primarily.
- 1 January 2021
- Published by Wiley in Advances in Materials Science and Engineering
- Vol. 2021 (1)
RetractedOpen Access[Retracted] Effect of Grey and White Portland Cement Fillers on Flexural and Shear Strength of GFRP Composite Material
The mechanical behaviour of glass fiber reinforced polymer (GFRP) composite depends on the type of matrix, filler, and fiber architecture. In order to develop high‐strength polymer matrix composites, the composites containing 5%, 10%, and 15% each of Portland grey and white cement filler are prepared by uniformly mixing the epoxy and filler materials, followed by casting by hand layup technique. The flexural and shear test is performed in accordance with ASTM 790 and ASTM D5379, respectively. It has been found that the values of shear strength, flexural strength, and modulus of elasticity vary with the increasing amount of cement component in the polymer. In addition, for a given percentage of the components of the cementitious filler, the values of the mechanical strength of the composites that contain white cement are higher than those of the composites that contain grey cement filler. Damage to composites has been found to involve fiber breakage and delamination primarily.