Srinivasu Dasari
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Srinivasu Dasari has a total of 17 co-authors. Here are the top co-authors by number of shared publications:
- Rajesh Kumar Prusty
FRP Composites Laboratory, Metallurgical and Materials Engineering National Institute of Technology Rourkela Rourkela Odisha India
7 shared publications - Bankim Chandra Ray
FRP Composite Laboratory, Department of Metallurgical and Materials Engineering National Institute of Technology Rourkela Odisha India
5 shared publications - Satyaroop Patnaik
FRP Composite Laboratory, Department of Metallurgical and Materials Engineering National Institute of Technology Rourkela India
5 shared publications Bankim Chandra Ray
FRP Composite Lab, Department of Metallurgical and Materials Engineering , National Institute of Technology , Rourkela , India
3 shared publicationsRajesh Kumar Prusty
FRP Composite Lab, Department of Metallurgical and Materials Engineering , National Institute of Technology , Rourkela , India
3 shared publicationsShiny Lohani
FRP Composites Laboratory, Department of Metallurgical and Materials Engineering National Institute of Technology Rourkela India
2 shared publications
Latest Publications
- 27 July 2023
- Published by Wiley in Polymer Composites
- Vol. 44 (10) , 6793-6810
Temperature‐dependent inter‐laminar fracture behavior of waste short carbon fiber embedded glass fiber/epoxy composites
Delamination is one of the life‐limiting failure modes for fiber reinforced polymer (FRP) composite composites resulting in poor damage tolerance, as this failure mode occurs at considerably lower loads. Owing to the enormous demand and mass production of FRP composites, a large amount of fiber waste is produced worldwide. This triggers concern about utilizing these fiber wastes for some valuable applications. The present study aims to improve the overall damage tolerance of laminated glass/epoxy composites via the introduction of waste short carbon fibers (SCFs) reinforcement in the epoxy matrix. The effect of various SCF contents (0.1, 0.3, and 0.5 wt%) in glass fiber/epoxy composites were evaluated experimentally for their interlaminar fracture toughness in terms of both crack development and propagation under mode I and II interlaminar fracture toughness tests, at elevated temperatures (30, 50, and 70°C). Based on the experimental results, glass/epoxy composite with 0.1 wt% of SCF revealed 13.49% and 20.45% increment in mode I and II interlaminar fracture toughness, respectively, at ambient temperature. A positive reinforcement effect could be noticed for GIC and GIIC values up to 50°C. However, due to residual interfacial stresses, interfacial debonding, and epoxy softening, a negative reinforcement effect could be noticed at 70°C. Delamination initiation and crack propagation mechanisms have been explored at elevated temperatures. Fractographic studies have been carried out using a scanning electron microscope to identify the failure mechanisms.
- 27 July 2023
- Published by Wiley in Polymer Composites
- Vol. 44 (10) , 6793-6810
Temperature‐dependent inter‐laminar fracture behavior of waste short carbon fiber embedded glass fiber/epoxy composites
Delamination is one of the life‐limiting failure modes for fiber reinforced polymer (FRP) composite composites resulting in poor damage tolerance, as this failure mode occurs at considerably lower loads. Owing to the enormous demand and mass production of FRP composites, a large amount of fiber waste is produced worldwide. This triggers concern about utilizing these fiber wastes for some valuable applications. The present study aims to improve the overall damage tolerance of laminated glass/epoxy composites via the introduction of waste short carbon fibers (SCFs) reinforcement in the epoxy matrix. The effect of various SCF contents (0.1, 0.3, and 0.5 wt%) in glass fiber/epoxy composites were evaluated experimentally for their interlaminar fracture toughness in terms of both crack development and propagation under mode I and II interlaminar fracture toughness tests, at elevated temperatures (30, 50, and 70°C). Based on the experimental results, glass/epoxy composite with 0.1 wt% of SCF revealed 13.49% and 20.45% increment in mode I and II interlaminar fracture toughness, respectively, at ambient temperature. A positive reinforcement effect could be noticed for GIC and GIIC values up to 50°C. However, due to residual interfacial stresses, interfacial debonding, and epoxy softening, a negative reinforcement effect could be noticed at 70°C. Delamination initiation and crack propagation mechanisms have been explored at elevated temperatures. Fractographic studies have been carried out using a scanning electron microscope to identify the failure mechanisms.
- 24 June 2023
- Published by Wiley in Polymer Composites
- Vol. 44 (9) , 5514-5526
Enhanced interlaminar mechanical behavior of advanced fiber metal laminates via nano Al2O3‐IPN formation and surface pre‐treatments
The inferior delamination resistance and out‐of‐plane performance of fiber metal laminates (FMLs) are of serious concerns. This work employs two modification methods, namely metal surface's chemical pre‐treatment and nano Al2O3 embedded interpenetrating polymer network (IPN) formation for improving the delamination resistance of aluminum and glass fiber‐reinforced polymer (GFRP) composite‐based FMLs. The synergetic effect of the two modification techniques resulted in high degrees of improvement in delamination resistance that were ~28% for critical strain energy release rate during mode‐I interlaminar fracture toughness (ILFT), that is (GIC) and ~37% for GIIC. Simultaneously, the flexural strength, tensile strength, and interlaminar shear strength improved by ~23%, ~17%, and ~24%, respectively. Scanning electron microscopy, atomic force microscopy, and surface energy measurement studies showed that the chemical pre‐treatment significantly influenced the surface morphology, surface roughness, and surface energy responses of aluminum, respectively. Fractographic study validated the effect of modification methods on the failure behavior under various testing modes.
- 24 June 2023
- Published by Wiley in Polymer Composites
- Vol. 44 (9) , 5514-5526
Enhanced interlaminar mechanical behavior of advanced fiber metal laminates via nano Al2O3‐IPN formation and surface pre‐treatments
The inferior delamination resistance and out‐of‐plane performance of fiber metal laminates (FMLs) are of serious concerns. This work employs two modification methods, namely metal surface's chemical pre‐treatment and nano Al2O3 embedded interpenetrating polymer network (IPN) formation for improving the delamination resistance of aluminum and glass fiber‐reinforced polymer (GFRP) composite‐based FMLs. The synergetic effect of the two modification techniques resulted in high degrees of improvement in delamination resistance that were ~28% for critical strain energy release rate during mode‐I interlaminar fracture toughness (ILFT), that is (GIC) and ~37% for GIIC. Simultaneously, the flexural strength, tensile strength, and interlaminar shear strength improved by ~23%, ~17%, and ~24%, respectively. Scanning electron microscopy, atomic force microscopy, and surface energy measurement studies showed that the chemical pre‐treatment significantly influenced the surface morphology, surface roughness, and surface energy responses of aluminum, respectively. Fractographic study validated the effect of modification methods on the failure behavior under various testing modes.
- 21 April 2023
- Published by Wiley in Polymer Composites
- Vol. 44 (6) , 3622-3633
Mode I and II interlaminar fracture toughness of glass/carbon inter‐ply hybrid FRP composites: Effects of stacking sequence and testing temperature
Even though laminated FRP composites show exceptional performance in various modes of loading, they are susceptible to delamination. The ambient temperature and elevated temperature delamination resistance of glass/carbon fiber interply hybrid composites were assessed via mode I and mode II interlaminar fracture toughness tests performed at 30, 50 and 70°C. Interply hybrid composites performed better than composites with single type of fiber. The fracture toughness of inter‐ply hybrid composites varied with the stacking position. At 30°C, mode I fracture toughness value of alternative glass and carbon fiber stacking sequence (G1C1)5 of hybrid composite showed 40% improvement over 10 layered carbon/epoxy (C10) composite. Further, Mode II fracture toughness of C5G5 composite showed 22% enhancement, and C10 exhibited 42% improvement over 10‐layered glass/epoxy composite. Increasing the test temperature of all composites improved their GIC and GIIC values. The increment in the mode I fracture toughness properties of all composite was in the range of 5%–23% at 70°C from its room temperature value. The fractographic images of fractured samples were studied under a scanning electron microscope and failure mechanisms of composites were identified.
- 21 April 2023
- Published by Wiley in Polymer Composites
- Vol. 44 (6) , 3622-3633
Mode I and II interlaminar fracture toughness of glass/carbon inter‐ply hybrid FRP composites: Effects of stacking sequence and testing temperature
Even though laminated FRP composites show exceptional performance in various modes of loading, they are susceptible to delamination. The ambient temperature and elevated temperature delamination resistance of glass/carbon fiber interply hybrid composites were assessed via mode I and mode II interlaminar fracture toughness tests performed at 30, 50 and 70°C. Interply hybrid composites performed better than composites with single type of fiber. The fracture toughness of inter‐ply hybrid composites varied with the stacking position. At 30°C, mode I fracture toughness value of alternative glass and carbon fiber stacking sequence (G1C1)5 of hybrid composite showed 40% improvement over 10 layered carbon/epoxy (C10) composite. Further, Mode II fracture toughness of C5G5 composite showed 22% enhancement, and C10 exhibited 42% improvement over 10‐layered glass/epoxy composite. Increasing the test temperature of all composites improved their GIC and GIIC values. The increment in the mode I fracture toughness properties of all composite was in the range of 5%–23% at 70°C from its room temperature value. The fractographic images of fractured samples were studied under a scanning electron microscope and failure mechanisms of composites were identified.
- 1 April 2023
- Published by Walter de Gruyter GmbH in International Journal of Materials Research
- Vol. 114 (4-5) , 276-283
Flexural behavior of carbon/glass inter-ply hybrid FRP composites under elevated temperature environments
In this research work, the three-point flexural performance of carbon and/or glass inter-ply hybrid epoxy composite by altering the hybrid ratio and stacking position was studied. These materials were tested at various temperatures (30 °C, 50 °C, 70 °C and 110 °C). The test results of hybrid composites results were compared with neat glass/epoxy and carbon/epoxy composites. The stacking position of carbon fibers in hybrid composite plays a vital role while doing a flexural test. Incorporation of two stiffer carbon fibers in glass/epoxy composite i.e., C2G3 and C1G3C1, resulted in a remarkable increment in the case of flexural strength. All composites exhibited ductile behavior at 110 °C. The fractured surfaces revealed the failure mechanism of the composites.
- 1 April 2023
- Published by Walter de Gruyter GmbH in International Journal of Materials Research
- Vol. 114 (4-5) , 276-283
Flexural behavior of carbon/glass inter-ply hybrid FRP composites under elevated temperature environments
In this research work, the three-point flexural performance of carbon and/or glass inter-ply hybrid epoxy composite by altering the hybrid ratio and stacking position was studied. These materials were tested at various temperatures (30 °C, 50 °C, 70 °C and 110 °C). The test results of hybrid composites results were compared with neat glass/epoxy and carbon/epoxy composites. The stacking position of carbon fibers in hybrid composite plays a vital role while doing a flexural test. Incorporation of two stiffer carbon fibers in glass/epoxy composite i.e., C2G3 and C1G3C1, resulted in a remarkable increment in the case of flexural strength. All composites exhibited ductile behavior at 110 °C. The fractured surfaces revealed the failure mechanism of the composites.
- 7 October 2022
- Published by Wiley in Polymer Composites
- Vol. 43 (12) , 9119-9130
Elevated temperature mechanical behavior of waste short carbon fiber incorporated glass fiber/epoxy composites
The fabrication of carbon fiber‐reinforced polymer composites generates vast amounts of waste carbon fiber. In the present work, these waste carbon fibers were added in varying contents (0.1, 0.3, and 0.5 wt%) to glass fiber/epoxy (GE) composite as short carbon fibers (SCFs) to improve its ambient and elevated temperature mechanical performance. The flexural and tensile behavior of the SCF modified GE composites were assessed at 30, 50, 70, and 110°C. The most significant improvement in mechanical performance was achieved by adding only 0.1 wt% of SCF into GE composite across most of the temperatures. At elevated temperatures, all the SCF‐modified GE composites showed superior mechanical performance over the control GE composite. An important correlation between SCF content in GE composite and elevated temperature mechanical performance enhancement has been discussed. Differential scanning calorimetry was performed to understand the effect of SCF addition on GE composite's glass transition behavior. Fractography was conducted to study the various failure mechanisms at ambient and elevated temperatures.
- 7 October 2022
- Published by Wiley in Polymer Composites
- Vol. 43 (12) , 9119-9130
Elevated temperature mechanical behavior of waste short carbon fiber incorporated glass fiber/epoxy composites
The fabrication of carbon fiber‐reinforced polymer composites generates vast amounts of waste carbon fiber. In the present work, these waste carbon fibers were added in varying contents (0.1, 0.3, and 0.5 wt%) to glass fiber/epoxy (GE) composite as short carbon fibers (SCFs) to improve its ambient and elevated temperature mechanical performance. The flexural and tensile behavior of the SCF modified GE composites were assessed at 30, 50, 70, and 110°C. The most significant improvement in mechanical performance was achieved by adding only 0.1 wt% of SCF into GE composite across most of the temperatures. At elevated temperatures, all the SCF‐modified GE composites showed superior mechanical performance over the control GE composite. An important correlation between SCF content in GE composite and elevated temperature mechanical performance enhancement has been discussed. Differential scanning calorimetry was performed to understand the effect of SCF addition on GE composite's glass transition behavior. Fractography was conducted to study the various failure mechanisms at ambient and elevated temperatures.
- 1 October 2022
- Published by Wiley in Polymer Composites
- Vol. 44 (1) , 294-304
Effects of in‐situ cryogenic testing temperature and ex‐situ cryogenic aging on the mechanical performance of glass fiber reinforced polymer composites with waste short carbon fibers as secondary reinforcements
Composite components' fabrication generates vast amounts of fiber wastes. This research suggests using short carbon fibers (SCFs) as secondary reinforcement in glass fiber reinforced polymer (GFRP) composite for cryogenic application. The SCFs (0.1, 0.3, and 0.5 wt%) were embedded in GFRP composites. Flexural test was performed to assess the integrity and durability of composites at in‐situ cryogenic temperature (CT), and after ex‐situ cryo‐aging in liquid nitrogen for various time intervals (0.25, 0.5, 1, 2, 4, 8, and 16 h). The composite with 0.1 wt% of SCFs showed the highest enhancement in flexural performance in all testing conditions, ∼16% at Room Temperature (RT), ∼12% at Cryogenic Temperature (CT, and between 13% and 39% after cryo‐aging. Composites with SCFs retained their strength at CT and after cryo‐aging, suggesting that the waste fibers could be economically reused and preferred over other expensive nanofillers as secondary reinforcements in GFRP composites for cryogenic applications.
- 1 October 2022
- Published by Wiley in Polymer Composites
- Vol. 44 (1) , 294-304
Effects of in‐situ cryogenic testing temperature and ex‐situ cryogenic aging on the mechanical performance of glass fiber reinforced polymer composites with waste short carbon fibers as secondary reinforcements
Composite components' fabrication generates vast amounts of fiber wastes. This research suggests using short carbon fibers (SCFs) as secondary reinforcement in glass fiber reinforced polymer (GFRP) composite for cryogenic application. The SCFs (0.1, 0.3, and 0.5 wt%) were embedded in GFRP composites. Flexural test was performed to assess the integrity and durability of composites at in‐situ cryogenic temperature (CT), and after ex‐situ cryo‐aging in liquid nitrogen for various time intervals (0.25, 0.5, 1, 2, 4, 8, and 16 h). The composite with 0.1 wt% of SCFs showed the highest enhancement in flexural performance in all testing conditions, ∼16% at Room Temperature (RT), ∼12% at Cryogenic Temperature (CT, and between 13% and 39% after cryo‐aging. Composites with SCFs retained their strength at CT and after cryo‐aging, suggesting that the waste fibers could be economically reused and preferred over other expensive nanofillers as secondary reinforcements in GFRP composites for cryogenic applications.
- 15 November 2021
- Published by Wiley in Journal of Applied Polymer Science
- Vol. 139 (12) , 51841
An assessment of mechanical behavior of glass fiber/epoxy composites with secondary short carbon fiber reinforcements
Utilizing recycled or short fibers for making useful engineering composite component is a present research trend and requirement. Current research work explicates the effect of short carbon fibers (SCF) used as secondary reinforcement in woven glass/epoxy hybrid composites and evaluates their mechanical properties. Different concentrations (0.1, 0.3, and 0.5 wt%) of SCF were incorporated to assess the tensile, flexural, and interlaminar fracture toughness (Mode I and II) of the resulted composites. Composites with 0.1 wt% SCF showed 29.02% and 16.08% increment in the tensile and flexural strength, respectively. For Mode I and Mode II interlaminar fracture toughness tests, 0.1 wt% SCF‐GE samples showed the highest strain energy release rate. Double cantilever beam specimens were used for Mode I testing and an improvement of 13.49% invalue was observed. End‐notched flexure method was used for the Mode II tests, and 0.1 wt% SCF‐GE samples showed 20.45% increase invalues. This paper explains the various reasons and mechanisms for obtaining such results. Scanning electron microscopy of the fractured surfaces was carried out to perceive the diverse failure micro‐mechanisms that could have been involved.
- 15 November 2021
- Published by Wiley in Journal of Applied Polymer Science
- Vol. 139 (12) , 51841
An assessment of mechanical behavior of glass fiber/epoxy composites with secondary short carbon fiber reinforcements
Utilizing recycled or short fibers for making useful engineering composite component is a present research trend and requirement. Current research work explicates the effect of short carbon fibers (SCF) used as secondary reinforcement in woven glass/epoxy hybrid composites and evaluates their mechanical properties. Different concentrations (0.1, 0.3, and 0.5 wt%) of SCF were incorporated to assess the tensile, flexural, and interlaminar fracture toughness (Mode I and II) of the resulted composites. Composites with 0.1 wt% SCF showed 29.02% and 16.08% increment in the tensile and flexural strength, respectively. For Mode I and Mode II interlaminar fracture toughness tests, 0.1 wt% SCF‐GE samples showed the highest strain energy release rate. Double cantilever beam specimens were used for Mode I testing and an improvement of 13.49% invalue was observed. End‐notched flexure method was used for the Mode II tests, and 0.1 wt% SCF‐GE samples showed 20.45% increase invalues. This paper explains the various reasons and mechanisms for obtaining such results. Scanning electron microscopy of the fractured surfaces was carried out to perceive the diverse failure micro‐mechanisms that could have been involved.
- 26 July 2021
- Published by Elsevier in Materials Today: Proceedings
- Vol. 47, 3370-3374
A novel study of flexural behavior of short glass fibers as secondary reinforcements in GFRP composite
- 26 July 2021
- Published by Elsevier in Materials Today: Proceedings
- Vol. 47, 3370-3374
A novel study of flexural behavior of short glass fibers as secondary reinforcements in GFRP composite
- 1 January 2020
- Published by Elsevier in Materials Today: Proceedings
- Vol. 33, 5328-5333
Mode I interlaminar fracture toughness improvement of the glass/epoxy composite by using multiscale composite approach
- 1 January 2020
- Published by Elsevier in Materials Today: Proceedings
- Vol. 33, 5328-5333
Mode I interlaminar fracture toughness improvement of the glass/epoxy composite by using multiscale composite approach