VZVilor L. Zakovorotny

Vilor L. Zakovorotny

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article


Vilor L. Zakovorotny has a total of 34 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Dependence of tool wear on evolutionary changes in parameters of the dynamic cutting system

    by Valeria Gvindjilia, Vilor Zakovorotny

    Introduction. A fundamental property of a dynamic cutting system (DCS) is its evolutionary change, caused by irreversible energy transformations in the machining zone. Within this process, the progression of tool wear acts as one of the factors influencing the evolution, while simultaneously being dependent on the state of the DCS. Consequently, wear depends on the parameters of the DCS, and the progression of wear alters the parameters of the dynamic coupling formed by cutting. In this interconnected, and therefore self-organizing, system, the intensity of wear becomes dependent on the initial parameters of the DCS, and the wear trajectory becomes dependent on the initial parameters of the system. However, to date, wear has not been considered as part of an interconnected set of subsystems. Subject. This study examines tool wear as an integral part of an evolutionarily changing cutting system, characterized by the interplay between its coordinates and wear. In particular, it investigates the patterns of change in wear trajectories as a function of the initial parameters of the cutting system. The aim of this study is to investigate the effect of irreversible energy transformations on tool wear in order to align it with the parameters of the DCS. Methods. This paper presents the results of mathematical modelling of the evolutionary changes in the properties of a DCS, which are determined by the phase trajectory of the power of irreversible energy conversions based on the work done. It examines a DCS model in which wear is described using Volterra’s equation, discusses the challenges of parameterizing the equations, presents the results of numerical modelling, and provides a practical example. Results and Discussion. The results of modelling the relationship between wear and DCS parameters, and control parameters (namely, machining conditions), are presented and discussed. An example is given of how the wear behavior changes during the turning of 0.1 C–1.0 Mn-2.0 Ni-0.3 Cu-0.7 V steel. It is demonstrated that the evolutionary properties of wear can be highly sensitive to small variations in the initial DCS parameters, disturbances, and control parameters. The problem of selecting the optimal cutting speed trajectory based on the work done by the forces is also considered, as well as the use of the developed mathematical tools to create a digital twin of the machining process.

  • Information properties of vibroacoustic emission in diagnostic systems for cutting tool wear

    by Vilor Zakovorotny, Valery Gvindjiliya, Kirill Kislov

    Introduction. This paper is devoted to the development of a methodology for diagnosing cutting tool wear based on the analysis of vibroacoustic emission signals. Two tasks are addressed. Firstly, the information feature space related to wear is constructed. Secondly, within this space, decision rules are defined that allow division into separate clusters according to wear levels. Since the construction of the information feature space (IFS) methods is of primary importance in these procedures, the purpose of this work is to determine the regularities of changes in the frequency characteristics of the dynamic cutting system caused by wear development and to construct, on this basis, a rational information space for diagnosing tool wear. Method and methodology. The study is based on mathematical modeling results of a perturbed dynamic cutting system to determine the information feature space representing tool wear. Methods for determining the parameters of information signal parameters (ISPs) are proposed, which provide high sensitivity to wear changes. All ISP parameters should be dimensionless and zeroed at zero wear. They must satisfy additional requirements, including noise immunity conditions. Results and discussion. The paper presents results of constructing ISP parameters for vibroacoustic emission analysis in two frequency ranges. In the low-frequency range, limited by the first natural frequencies of interacting subsystems (up to 1.0–1.5 kHz), vibration response parameters (VRP) are determined based on vibration sequences obtained analytically under power perturbations modeled as “white” noise. In the high-frequency range (above 2.0 kHz), information models based on random pulse sequences are proposed. It is shown that the applicability of a particular information feature depends on the conditions. Thus, the developed methodology, mathematical simulation, and digital and field experiments enabled the formation of a rational information space for wear diagnostics, in which known recognition methods can be used to construct decision rules for classifying information according to wear levels.


  • Open Access

    System-synergetic analysis and synthesis of a controlled cutting process

    by Vilor Zakovorotny, Valeriya Gvindzhiliya

    Currently, good progress has been produced in the creation of machine tools with CNC computer systems. They are able to ensure the coincidence of program and the trajectories of the actuators with high accuracy. But when manufacturing parts with the same accuracy it becomes possible in rare circumstances. This is because of the necessity to take into account the entire controlled dynamic cutting system when manufacturing parts, while the quality of the part depends on various physical interactions under process work. In contrast to the well-known research and development, the paper focuses on the fact that the modeling level is based on a system-synergetic representation, which includes the procedure of expansion – compression of the state space. The system takes into account elastic deformations of its elements, evolutionary changes in their properties, uncontrollable disturbances, revealing physical interactions. This is a complex system, where its individual coordinates of the state depend on programmable trajectories first of all, secondly, they are characterized by internal connections and self-organization, and finally, they affect the output properties of cutting. The output properties include parts quality parameters and specified costs for parts manufacture. The article describes the main provisions of the synergetic system analysis and synthesis of a dynamic cutting system control, provides its mathematical modeling, views a simple procedure for analyzing and synthesizing a model. The example of practical application has been also observed.


  • Information properties of frequency characteristics of dynamic cutting systems in the diagnosis of tool wear

    by Vilor Zakovorotny, Valery Gvindjiliya, Kirill Kislov

    Introduction. One of the directions for increasing the efficiency of cutting is related to the creation of tool wear diagnostic systems. Algorithms and devices have been developed that evaluate wear based on analysis of the vibroacoustic emission signal. These algorithms, as a rule, do not reveal the nature of its formation and the reasons for the change as wear develops. Subject. The paper is devoted to the analysis of the reasons for changes in vibration properties with the development of tool wear. The aim of the work is to study the changes in the frequency characteristics of a dynamic cutting system caused by the development of wear, and to build diagnostic information models on this basis, as well as its use in industry. Method and methodology. The results of mathematical simulation of a perturbed dynamic cutting system are presented, in which the observed vibration sequences are a consequence of disturbances transformed by a dynamic system, the parameters of which depend on wear. Two frequency ranges are considered. Results and discussions. The first range includes frequencies that lie within the bandwidth of the instrument subsystem. The second is outside of it. In the first frequency range, it has been analytically and experimentally proven that the development of wear leads to fundamental changes in the frequency properties of the cutting system as a converter of disturbances into tool vibrations. There is a shift in the natural frequencies of the oscillatory circuits formed by the cutting system, a decrease in its quality factor, and as wear develops, some identified features of the vibration spectra appear, including the ratio of the low-frequency and high-frequency parts of the spectrum, etc. In the second frequency range, a model of force emission in the form of a random pulse sequence is considered and wear is displayed in it. The results of studying the coherence function between the forces acting on the tool and vibrational displacement are presented. Information models of wear are proposed, an example of an information model of wear and the results of its use in industry are given.

  • The features of the evolution of the dynamic cutting system due to the regenerative effect

    by Vilor Zakovorotny, Valery Gvindjiliya

    Dynamic machining system integrates tool and workpiece subsystems through the dynamic coupling formed by cutting. In studying the dynamics, equilibrium stabilit


  • Application of the synergistic concept in determining the CNC program for turning

    by Vilor Zakovorotny, Valery Gvindjiliya, Elina Fesenko

    Introduction. One of the dynamically developing areas of increasing the efficiency of CNC machines is associated with the use of the synergetic concept in determining the CNC program. The principle of compression-expansion of the dimensionality of the state space is used. Subject. On the example of the workpiece machining, the stiffness parameters of which are a function of the toolpath, all stages of control synthesis, which ensures the mutual consistency of dynamic subsystems, including the cutting process, are described in the paper. The aim of the work is to determine asymptotically stable machine actuator toolpath, given by CNC program parameters, from the set of paths, for which the condition of minimum wear intensity is fulfilled. Method and methodology. Mathematical modeling of the controlled cutting system, which is based on the principle of compression-expansion state space, is presented. When the dimension of the state space is expanded, the model of the dynamic cutting system includes all elements from the CNC system that programs the motion of the actuating elements to the elastic deformations of the tool, which interacts with the workpiece through the connection formed by the cutting process. The dynamic coupling integrates the subsystems into a single coupled control system. In this space, the desired shaping motion path of the tool tip relative to the workpiece is constructed, which should be the attractor of the entire state space. The transformation of the desired motion path into an attractor characterizes the procedure of compressing the dimensionality of the state space. It is supposed that it is possible to control the motion trajectories of the actuators within the bandwidths of the servomotors. Results and Discussion. The analysis of the stability of the cutting process is performed; the example of the efficiency of a NC program on the basis of the synergetic paradigm is presented. It is shown that by coordinating the external control with the internal dynamics of the system it is possible to increase the efficiency of a part production up to two times in machine time.


  • Synergetic approach to improve the efficiency of machining process control on metal-cutting machines

    by Vilor Zakovorotny, Valery Gvindjiliya

    Introduction. The efficiency of processing on metal-cutting machines is evaluated by the reduced cost of producing a batch of parts while ensuring the required quality. In modern production, parts are usually made on CNC machines. Today the CNC program and the trajectories of the machine tool actuators match each other with high accuracy, which, however, does not yet guarantee quality and efficiency of production. The definition of the CNC program is based on the knowledge base of rational modes, tools, coolant and etc. during processing. This base reflects some averaging over the set of machines, tools and processing conditions, and does not take into account changes in the properties of the dynamic system in the process of cutting. Subject. The paper deals with the synergistic matching of external control (CNC programs) and cutting dynamics (internal control). The internal control factors can be set a priori, as well as determined as a result of the influence of irreversible energy transformations in the cutting zone. The purpose of the work is to determine the law of controlling the trajectories of the machine's executive elements in such a way that, with changing properties of the dynamic cutting system, the required surface quality of the part and minimizing the intensity of tool wear are ensured during the processing of the part. Method and methodology. Mathematical simulation of the controlled dynamic system, which properties change due to the a priori set laws of variation of subsystem parameters, as well as changes in the cutting properties conditioned by the power of irreversible energy transformation is presented. Consideration of the power of irreversible energy transformations is necessary for predicting back-edge wear, changes in dynamic coupling parameters, and evolutionary restructuring of cutting dynamics. Results and Discussion. The regularity of matching the CNC program with the changing properties of the cutting process, which allows increasing the processing efficiency while ensuring the required quality of parts, is disclosed. A number of properties of the dynamic cutting system caused by changing trajectory of the longitudinal feed rate of the tool during processing of the shaft, the stiffness change of which is given, are revealed and analyzed.


  • Open Access

    Influence of stiffness of the mechanical part of the drive and cutting parameters on the shaping elastic deformation control

    by В. Л. Заковоротный, V. Е. Gvindjiliya, А. А. Zakalyuzhny

    Introduction. One of the ways to improve the accuracy of manufacturing parts by cutting is related to the control of elastic deformations of the tool and the workpiece. This is particularly true for slender parts, whose stiffness law along the tool path is given. In this case, the control parameter, as a rule, is the return flow rate, which affects the cutting forces, whose change causes variations in elastic deformations. To provide the specified accuracy of the diameter, it is required to coordinate the controlled trajectory of the feed drive speed with the feed rate and a priori given law of change in the stiffness of the workpiece or the law of variation of the cutting process parameters. To do this, it is required to determine the law of converting the engine speed into the feed rate, and, ultimately, into elastic deformations. This law depends on the stiffness of the mechanical part of the feed drive and the changing parameters of the cutting process. Materials and Methods. The paper presents mathematical modeling and, on its basis, analysis of the conversion of the feed rate into cutting forces, taking into account the final stiffness value of the mechanical part of the drive and the evolutionary parameters of the cutting process. Results. It is shown that, starting from a certain critical value, the law of converting the feed rate into cutting forces becomes fundamentally dependent on the stiffness of the mechanical part of the drive. At the same time, there is an increase in time for setting a new force value when the feed rate varies, which affects the accuracy of providing forces that are consistent with the stiffness law of the part. The paper presents algorithms for calculating elastic deformations for a given stiffness law, as well as algorithms for calculating the trajectory of the feed rate at which the deformations remain constant. It is shown that the law of conversion is also affected by variations in the cutting parameters. Discussion and Conclusion. The frequency and time characteristics of the conversion are discussed. A conclusion is made about the accuracy of the diameter formed through cutting, depending on the stiffness of the mechanical part of the feed drive and on some parameters of the cutting process.