Weilei Wang
Research Subjects
Weilei Wang has a total of 13 co-authors. Here are the top co-authors by number of shared publications:
- Weili Liu
National Key Laboratory of Materials for Integrated Circuits, Shanghai Institute of Microsystem and Information Technology, Chinese Academy of Sciences, 865 Changning Road, Shanghai 200050, China
6 shared publications - Zhitang Song
State Key Laboratory of Functional Materials for Informatics, Shanghai Institute of Microsystem and Information Technology, Chinese Academy of Sciences, Shanghai, China
4 shared publications Zhitang Song
State Key Laboratory of Functional Materials for Informatics, Laboratory of Nanotechnology, Shanghai Institute of Microsystem and Information Technology, Chinese Academy of Sciences, Shanghai 200050, People’s Republic of China
3 shared publications- Juntao Gong
National Key Laboratory of Materials for Integrated Circuits, Shanghai Institute of Microsystem and Information Technology, Chinese Academy of Sciences, 865 Changning Road, Shanghai 200050, China
2 shared publications Qiufeng Xu
Piezoelectric Crystal Division, TDG HOLDING Co., Ltd., Zhejiang 314412, People’s Republic of China
2 shared publicationsBai Lin-Sen
1 shared publication
Latest Publications
- Open Access
- 22 August 2024
- Published by MDPI AG in Nanomaterials
- Vol. 14 (16) , 1371
Enhancing Slurry Stability and Surface Flatness of Silicon Wafers through Organic Amine-Catalyzed Synthesis Silica Sol
The stability of slurries used for chemical mechanical polishing (CMP) is a crucial concern in industrial chip production, influencing both the quality and cost-effectiveness of polishing fluids. In silicon wafer polishing, the conventional use of commercial neutral silica sol combined with organic bases often leads to slurry instability. To address this issue, this study proposes organic amines—specifically ethanolamine (MEA), ethylenediamine (EDA), and tetramethylammonium hydroxide (TMAOH)—as catalysts for synthesizing alkaline silica sol tailored for silicon wafer polishing fluids. Sol–gel experiments and zeta potential measurements demonstrate the efficacy of this approach in enhancing the stability of silica sol. The quantitative analysis of surface hydroxyl groups reveals a direct correlation between enhanced stability and increased hydroxyl content. The application of the alkaline silica sol in silicon wafer polishing fluids improves polishing rates and enhances surface flatness according to atomic force microscopy (AFM). In addition, electrochemical experiments validate the capability of this polishing solution to mitigate corrosion on silicon wafer surfaces. These findings hold significant implications for the advancement of chemical mechanical polishing techniques in the field of integrated circuit fabrication.
- 22 August 2024
- Published by MDPI AG in Nanomaterials
- Vol. 14 (16) , 1371
Open AccessEnhancing Slurry Stability and Surface Flatness of Silicon Wafers through Organic Amine-Catalyzed Synthesis Silica Sol
The stability of slurries used for chemical mechanical polishing (CMP) is a crucial concern in industrial chip production, influencing both the quality and cost-effectiveness of polishing fluids. In silicon wafer polishing, the conventional use of commercial neutral silica sol combined with organic bases often leads to slurry instability. To address this issue, this study proposes organic amines—specifically ethanolamine (MEA), ethylenediamine (EDA), and tetramethylammonium hydroxide (TMAOH)—as catalysts for synthesizing alkaline silica sol tailored for silicon wafer polishing fluids. Sol–gel experiments and zeta potential measurements demonstrate the efficacy of this approach in enhancing the stability of silica sol. The quantitative analysis of surface hydroxyl groups reveals a direct correlation between enhanced stability and increased hydroxyl content. The application of the alkaline silica sol in silicon wafer polishing fluids improves polishing rates and enhances surface flatness according to atomic force microscopy (AFM). In addition, electrochemical experiments validate the capability of this polishing solution to mitigate corrosion on silicon wafer surfaces. These findings hold significant implications for the advancement of chemical mechanical polishing techniques in the field of integrated circuit fabrication.
- Open Access
Polishing Mechanism of CMP 4H-SiC Crystal Substrate (0001) Si Surface Based on an Alumina (Al2O3) Abrasive
Silicon carbide, a third-generation semiconductor material, is widely used in the creation of high-power devices. In this article, we systematically study the influence of three crucial parameters on the polishing rate of a silicon carbide surface using orthogonal experiments. By optimizing the parameters of chemical mechanical polishing (CMP) through experiments, we determined that the material removal rate (MRR) is 1.2 μm/h and the surface roughness (Ra) is 0.093 nm. Analysis of the relevant polishing mechanism revealed that manganese dioxide formed during the polishing process. Finally, due to the electrostatic effect of the two, adsorbed on the , which explains the polishing mechanism of in the slurry.Open AccessPolishing Mechanism of CMP 4H-SiC Crystal Substrate (0001) Si Surface Based on an Alumina (Al2O3) Abrasive
Silicon carbide, a third-generation semiconductor material, is widely used in the creation of high-power devices. In this article, we systematically study the influence of three crucial parameters on the polishing rate of a silicon carbide surface using orthogonal experiments. By optimizing the parameters of chemical mechanical polishing (CMP) through experiments, we determined that the material removal rate (MRR) is 1.2 μm/h and the surface roughness (Ra) is 0.093 nm. Analysis of the relevant polishing mechanism revealed that manganese dioxide formed during the polishing process. Finally, due to the electrostatic effect of the two, adsorbed on the , which explains the polishing mechanism of in the slurry. - 1 November 2022
- Published by The Electrochemical Society in ECS Journal of Solid State Science and Technology
- Vol. 11 (11) , 114003
Effect of Ferric Nitrate on Semi-Insulating 4H-SiC (0001) Chemical Mechanical Polishing
Semi-insulating 4H-SiC (0001) has high hardness and high chemical inertness, making it difficult to obtain high material removal rates (MRR) during chemical mechanical polishing (CMP). In this paper, the role of chemical additive ferric nitrate in semi-insulating 4H-SiC(0001) chemical mechanical polishing with α -alumina as abrasive and KMnO 4 as oxidant was discussed. The results showed that 0.5 wt% ferric nitrate can increase the removal rate of semi-insulating 4H-SiC(0001) by 34%, while the semi-insulating 4H-SiC(0001) surface roughness Ra was reduced from 0.123 nm to 0.110 nm. The key point was that the coefficient of friction of the polishing slurry was effectively reduced, which was very beneficial to the ploughing effect of the α -alumina abrasive with vermicular thin section morphology which had the highest removal rate. In the second place, the chemical composition of 4H-SiC(0001) corrosion layer was analyzed by XPS under different corrosion conditions. Si 2P spectrum analysis showed that O atoms only attack C atoms to produce Si–C–O structure under acidic conditions. Whereas with the addition of ferric nitrate, O atoms not only attacked C atoms, but also attacked Si atoms to produce softer SiO 2 and Si-O x -C y structures. At the end of the paper, the chemical mechanical polishing mechanism of semi-insulating 4H-SiC(0001) was given.
- 1 November 2022
- Published by The Electrochemical Society in ECS Journal of Solid State Science and Technology
- Vol. 11 (11) , 114003
Effect of Ferric Nitrate on Semi-Insulating 4H-SiC (0001) Chemical Mechanical Polishing
Semi-insulating 4H-SiC (0001) has high hardness and high chemical inertness, making it difficult to obtain high material removal rates (MRR) during chemical mechanical polishing (CMP). In this paper, the role of chemical additive ferric nitrate in semi-insulating 4H-SiC(0001) chemical mechanical polishing with α -alumina as abrasive and KMnO 4 as oxidant was discussed. The results showed that 0.5 wt% ferric nitrate can increase the removal rate of semi-insulating 4H-SiC(0001) by 34%, while the semi-insulating 4H-SiC(0001) surface roughness Ra was reduced from 0.123 nm to 0.110 nm. The key point was that the coefficient of friction of the polishing slurry was effectively reduced, which was very beneficial to the ploughing effect of the α -alumina abrasive with vermicular thin section morphology which had the highest removal rate. In the second place, the chemical composition of 4H-SiC(0001) corrosion layer was analyzed by XPS under different corrosion conditions. Si 2P spectrum analysis showed that O atoms only attack C atoms to produce Si–C–O structure under acidic conditions. Whereas with the addition of ferric nitrate, O atoms not only attacked C atoms, but also attacked Si atoms to produce softer SiO 2 and Si-O x -C y structures. At the end of the paper, the chemical mechanical polishing mechanism of semi-insulating 4H-SiC(0001) was given.
- 1 April 2022
- Published by The Electrochemical Society in ECS Journal of Solid State Science and Technology
- Vol. 11 (4) , 044004
Effect of Particle Size Distribution, pH, and Na + Concentration on the Chemical Mechanical Polishing of Sapphire and 4H-SiC (0001)
As two typical representatives of super-hard materials, sapphire and silicon carbide, their processing has always been a hot spot. Chemical mechanical polishing (CMP) technology is the only way to achieve global planarization, and it has also become one of the most important processes for precision machining of sapphire and silicon carbide. This paper introduced the relationship between the removal rate and surface roughness of sapphire and 4H-SiC (0001) and the size distribution and pH of alumina slurry. More importantly, this paper explored the negative effect of Na + on the removal rate of alumina-based sapphire polishing slurry, and the more negative effect of Na + on the removal rate of alumina-based silicon carbide polishing slurry and the surface state of SiC(0001). At the end of the article, the polishing mechanism of sapphire with alumina as a brasive was given.
- 1 April 2022
- Published by The Electrochemical Society in ECS Journal of Solid State Science and Technology
- Vol. 11 (4) , 044004
Effect of Particle Size Distribution, pH, and Na + Concentration on the Chemical Mechanical Polishing of Sapphire and 4H-SiC (0001)
As two typical representatives of super-hard materials, sapphire and silicon carbide, their processing has always been a hot spot. Chemical mechanical polishing (CMP) technology is the only way to achieve global planarization, and it has also become one of the most important processes for precision machining of sapphire and silicon carbide. This paper introduced the relationship between the removal rate and surface roughness of sapphire and 4H-SiC (0001) and the size distribution and pH of alumina slurry. More importantly, this paper explored the negative effect of Na + on the removal rate of alumina-based sapphire polishing slurry, and the more negative effect of Na + on the removal rate of alumina-based silicon carbide polishing slurry and the surface state of SiC(0001). At the end of the article, the polishing mechanism of sapphire with alumina as a brasive was given.
- 1 April 2022
- Published by The Electrochemical Society in ECS Journal of Solid State Science and Technology
- Vol. 11 (4) , 044003
Effect of Neotame and pH on LiTaO 3 Chemical Mechanical Polishing
LiTaO 3 has piezoelectric, ferroelectric and pyroelectric optical properties with a broad transparent range from ultraviolet to infrared. In order to ensure good performance of the LiTaO 3 substrate, the surface of the LiTaO 3 substrate must be smooth. Chemical mechanical polishing has been used for planarization of integrated circuits or to obtain substrates of high surface quality. In this paper, neotame was studied as an additive for LiTaO 3 slurry, which plays an important role in the polishing process. In addition, this paper introduced that different pH and different concentrations of neotame have a strong influence on the polishing rate, and the surface roughness of the LiTaO 3 substrate after polishing is different, and the surface roughness of the LiTaO 3 substrate can be reduced to 0.112 nm. More importantly, neotame could improve the work-life of the polishing slurry and reduce the coefficient of friction, thereby reducing the fragmentation rate. Finally, the possible chemical reaction mechanism of neotame to accelerate polishing efficiency was given.
- 1 April 2022
- Published by The Electrochemical Society in ECS Journal of Solid State Science and Technology
- Vol. 11 (4) , 044003
Effect of Neotame and pH on LiTaO 3 Chemical Mechanical Polishing
LiTaO 3 has piezoelectric, ferroelectric and pyroelectric optical properties with a broad transparent range from ultraviolet to infrared. In order to ensure good performance of the LiTaO 3 substrate, the surface of the LiTaO 3 substrate must be smooth. Chemical mechanical polishing has been used for planarization of integrated circuits or to obtain substrates of high surface quality. In this paper, neotame was studied as an additive for LiTaO 3 slurry, which plays an important role in the polishing process. In addition, this paper introduced that different pH and different concentrations of neotame have a strong influence on the polishing rate, and the surface roughness of the LiTaO 3 substrate after polishing is different, and the surface roughness of the LiTaO 3 substrate can be reduced to 0.112 nm. More importantly, neotame could improve the work-life of the polishing slurry and reduce the coefficient of friction, thereby reducing the fragmentation rate. Finally, the possible chemical reaction mechanism of neotame to accelerate polishing efficiency was given.
- 1 July 2021
- Published by The Electrochemical Society in ECS Journal of Solid State Science and Technology
- Vol. 10 (7) , 074004
Two-Step Chemical Mechanical Polishing of 4H-SiC (0001) Wafer
Chemical mechanical polishing (CMP), as a widely used global smoothing technique, requires a high polishing rate and a low surface roughness. However, it is difficult to meet these requirements with single-step polishing. To obtain a perfect 4H-SiC wafer surface, we studied a two-step CMP 4H-SiC wafer using a-Al 2 O 3 -based slurry and nano-SiO 2 -based slurry. Before the two-step process was determined, the effect of concentration of KMnO 4 and pH on the polishing rate of 4H-SiC was first studied with Al 2 O 3 as the abrasive, and the maximum polishing rate of 1400 nm h −1 was determined under the condition of pH of 2.00 and KMnO 4 concentration of 6.5 wt% in the step. Furthermore, the effect of H 2 O 2 concentration on the polishing rate of 4H-SiC was investigated using SiO 2 as the abrasive and V 2 O 5 as the catalyst. It was determined that under the condition of V 2 O 5 concentration of 4 wt% and H 2 O 2 concentration of 10 wt%, the maximum polishing rate of the second step polishing was 150 nm h −1 , and a perfect surface was obtained, with a surface roughness of 0.066 nm. In addition, the in situ friction coefficients have used to characterize the two-step process. At the end, the CMP mechanisms of the above two slurry have been deduced and preliminarily demonstrated.
- 1 July 2021
- Published by The Electrochemical Society in ECS Journal of Solid State Science and Technology
- Vol. 10 (7) , 074004
Two-Step Chemical Mechanical Polishing of 4H-SiC (0001) Wafer
Chemical mechanical polishing (CMP), as a widely used global smoothing technique, requires a high polishing rate and a low surface roughness. However, it is difficult to meet these requirements with single-step polishing. To obtain a perfect 4H-SiC wafer surface, we studied a two-step CMP 4H-SiC wafer using a-Al 2 O 3 -based slurry and nano-SiO 2 -based slurry. Before the two-step process was determined, the effect of concentration of KMnO 4 and pH on the polishing rate of 4H-SiC was first studied with Al 2 O 3 as the abrasive, and the maximum polishing rate of 1400 nm h −1 was determined under the condition of pH of 2.00 and KMnO 4 concentration of 6.5 wt% in the step. Furthermore, the effect of H 2 O 2 concentration on the polishing rate of 4H-SiC was investigated using SiO 2 as the abrasive and V 2 O 5 as the catalyst. It was determined that under the condition of V 2 O 5 concentration of 4 wt% and H 2 O 2 concentration of 10 wt%, the maximum polishing rate of the second step polishing was 150 nm h −1 , and a perfect surface was obtained, with a surface roughness of 0.066 nm. In addition, the in situ friction coefficients have used to characterize the two-step process. At the end, the CMP mechanisms of the above two slurry have been deduced and preliminarily demonstrated.
- 1 January 2017
- Published by Shanghai Institute of Ceramics in Journal of Inorganic Materials
- Vol. 32 (10) , 1109-1114
Surface Modified Alumina Particles and Their Chemical Mechanical Polishing (CMP) Behavior on C-plane (0001) Sapphire Substrate
- 1 January 2017
- Published by Shanghai Institute of Ceramics in Journal of Inorganic Materials
- Vol. 32 (10) , 1109-1114
Surface Modified Alumina Particles and Their Chemical Mechanical Polishing (CMP) Behavior on C-plane (0001) Sapphire Substrate