Shidong Zheng
Research Subjects
Shidong Zheng has a total of 19 co-authors. Here are the top co-authors by number of shared publications:
- Qiuyi Li
College of Civil Engineering & Architecture, Qingdao Agricultural University, Qingdao 266109, China
2 shared publications - Yuanxin Guo
College of Civil Engineering & Architecture, Qingdao Agricultural University, Qingdao 266109, China
2 shared publications - Dunlei Su
School of Civil Engineering, Shandong Jiaotong University, Jinan 250357, China
1 shared publication - Gongbing Yue
College of Civil Engineering & Architecture, Qingdao Agricultural University, Qingdao 266109, China
1 shared publication - Guanghao Yang
School of Civil Engineering, Qingdao University of Technology, Qingdao 266525, China
1 shared publication - Guisheng Cai
Shandong Jianke Construction Materials Co., Ltd. Jinan, China
1 shared publication
Latest Publications
- Open Access
Properties of Light Cementitious Composite Materials with Waste Wood Chips
The CO2 emissions from the cement industry and the production of waste wood chips are increasing with the rapid growth of the construction industry. In order to develop a green environmental protection building material with low thermal conductivity and up to standard mechanical properties, in this study, pine waste wood chips were mixed into cement-based materials as fine aggregate, and three different kinds of cementitious binders were used, including sulfur aluminate cement (SAC), ordinary Portland cement (OPC), and granulated blast furnace slag (GBFS), to prepare a recycled light cementitious composite material. The mechanical, thermal conductivity, shrinkage, water absorption, and pore structure of a wood chip light cementitious composite material were studied by changing the Ch/B (the mass ratio of wood chip to binder). The results showed that the strength, dry density, and thermal conductivity of the specimens decreased significantly with the increase in the Ch/B, while the shrinkage, water absorption, and pore size increased with the increase in the Ch/B. By comparing three different kinds of cementitious binders, the dry density of the material prepared with OPC was 942 kg/m3, the compressive strength of the material prepared with SAC was 13.5 MPa, and the thermal conductivity of the material prepared with slag was the lowest at 0.15 W/m/K. From the perspective of low-cost and low-carbon emissions, it was determined that the best way to prepare a light cementitious composite with waste wood chips is to use granulated blast furnace slag (GBFS) as the cementitious binder.
Open AccessProperties of Light Cementitious Composite Materials with Waste Wood Chips
The CO2 emissions from the cement industry and the production of waste wood chips are increasing with the rapid growth of the construction industry. In order to develop a green environmental protection building material with low thermal conductivity and up to standard mechanical properties, in this study, pine waste wood chips were mixed into cement-based materials as fine aggregate, and three different kinds of cementitious binders were used, including sulfur aluminate cement (SAC), ordinary Portland cement (OPC), and granulated blast furnace slag (GBFS), to prepare a recycled light cementitious composite material. The mechanical, thermal conductivity, shrinkage, water absorption, and pore structure of a wood chip light cementitious composite material were studied by changing the Ch/B (the mass ratio of wood chip to binder). The results showed that the strength, dry density, and thermal conductivity of the specimens decreased significantly with the increase in the Ch/B, while the shrinkage, water absorption, and pore size increased with the increase in the Ch/B. By comparing three different kinds of cementitious binders, the dry density of the material prepared with OPC was 942 kg/m3, the compressive strength of the material prepared with SAC was 13.5 MPa, and the thermal conductivity of the material prepared with slag was the lowest at 0.15 W/m/K. From the perspective of low-cost and low-carbon emissions, it was determined that the best way to prepare a light cementitious composite with waste wood chips is to use granulated blast furnace slag (GBFS) as the cementitious binder.
- Open Access
Study on the Mechanical Properties and Durability of Recycled Aggregate Concrete under the Internal Curing Condition
Poor mechanical properties and durability of recycled aggregate concrete (RAC) hinder its application in the construction field. In this study, pre-wetted recycled coarse aggregate was used as the internal curing material for prepared RAC with low water-to-binder ratio (W/B), aiming to improve the mechanical properties and durability. The results show that the workability decreases with increasing contents of pre-wetted recycled coarse aggregate. The variation in compressive strength of RAC with different contents of pre-wetted recycled coarse aggregate is obvious within 28 d. After 28 d, the effect of internal curing of pre-wetted recycled coarse aggregate starts to occur, causing a sustained increase in compressive strength. The sealed concrete with 50% and 75% pre-wetted recycled coarse aggregate contents presents the highest compressive strength and better internal curing effect. The pre-wetted recycled coarse aggregate decreases the relative humidity inside the concrete and effectively inhibits the development of shrinkage in the early stages. The RAC with pre-wetted recycled coarse aggregate presents little effect on the drying shrinkage. Additionally, the electric flux of RAC cured for 28 d increases from 561C to 1001C, which presents good resistance to chloride permeation. Microscopic tests indicate that the incorporation of pre-wetted recycled coarse aggregate is beneficial to the improvements of internal structure of RAC.
Open AccessStudy on the Mechanical Properties and Durability of Recycled Aggregate Concrete under the Internal Curing Condition
Poor mechanical properties and durability of recycled aggregate concrete (RAC) hinder its application in the construction field. In this study, pre-wetted recycled coarse aggregate was used as the internal curing material for prepared RAC with low water-to-binder ratio (W/B), aiming to improve the mechanical properties and durability. The results show that the workability decreases with increasing contents of pre-wetted recycled coarse aggregate. The variation in compressive strength of RAC with different contents of pre-wetted recycled coarse aggregate is obvious within 28 d. After 28 d, the effect of internal curing of pre-wetted recycled coarse aggregate starts to occur, causing a sustained increase in compressive strength. The sealed concrete with 50% and 75% pre-wetted recycled coarse aggregate contents presents the highest compressive strength and better internal curing effect. The pre-wetted recycled coarse aggregate decreases the relative humidity inside the concrete and effectively inhibits the development of shrinkage in the early stages. The RAC with pre-wetted recycled coarse aggregate presents little effect on the drying shrinkage. Additionally, the electric flux of RAC cured for 28 d increases from 561C to 1001C, which presents good resistance to chloride permeation. Microscopic tests indicate that the incorporation of pre-wetted recycled coarse aggregate is beneficial to the improvements of internal structure of RAC.
- Open Access
- 27 July 2021
- Published by MDPI AG in Sustainability
- Vol. 13 (15) , 8385
Study of the Properties of Full Component Recycled Dry-Mixed Masonry Mortar and Concrete Prepared from Construction Solid Waste
Solutions are needed to solve the problem of a large amount of construction solid waste and a shortage of natural aggregate (coarse and fine aggregates). In this paper, simple-crushed coarse aggregate (SCRCA) and simple-crushed fine aggregate (SCRFA) were obtained by simple-crushing of construction solid waste. On this basis, SCRCA and SCRFA were treated with particle-shaping to obtain particle-shaping coarse aggregate (PSRCA) and particle-shaping fine aggregate (PSRFA), and the recycled powder (RP) produced in the process of particle-shaping was collected. Under the condition of a 1:4 cement-sand ratio, RP was used to replace cement with four substitution rates of 0, 10%, 20%, and 30%, and dry-mixed masonry mortar was prepared with 100% SCRFA, PSRFA, and river sand (RS). The basic and mechanical properties and microstructure of hydration products of dry-mixed mortar were analyzed, and the maximum substitution rate of RP was determined. Under the condition that the amount of cementitious material is 400 kg/m3 and the RP is at the maximum replacement rate, three different aggregate combinations to prepare concrete are the 100% use of SCRCA and SCRFA, PSRCA and PSRFA, and RS and natural aggregate (NCA); the workability, mechanical properties, and aggregate interface transition zone of the prepared concrete were analyzed. The results show that when the replacement rate of RP is less than 20%, it has little effect on the properties of products. The performance of PSRCA and PSRFA after treatment is better than that of SCRCA and SCRFA. Under different RP substitution rates, the performance of dry-mixed mortar prepared with PSRFA is very close to that prepared with RS. The performance of recycled concrete prepared with PSRCA and PSRFA is also very close to that of products prepared with NCA and RS. The failure morphology of PSRCA and RSRFA concrete is also similar to that of NCA and RS concrete.
- 27 July 2021
- Published by MDPI AG in Sustainability
- Vol. 13 (15) , 8385
Open AccessStudy of the Properties of Full Component Recycled Dry-Mixed Masonry Mortar and Concrete Prepared from Construction Solid Waste
Solutions are needed to solve the problem of a large amount of construction solid waste and a shortage of natural aggregate (coarse and fine aggregates). In this paper, simple-crushed coarse aggregate (SCRCA) and simple-crushed fine aggregate (SCRFA) were obtained by simple-crushing of construction solid waste. On this basis, SCRCA and SCRFA were treated with particle-shaping to obtain particle-shaping coarse aggregate (PSRCA) and particle-shaping fine aggregate (PSRFA), and the recycled powder (RP) produced in the process of particle-shaping was collected. Under the condition of a 1:4 cement-sand ratio, RP was used to replace cement with four substitution rates of 0, 10%, 20%, and 30%, and dry-mixed masonry mortar was prepared with 100% SCRFA, PSRFA, and river sand (RS). The basic and mechanical properties and microstructure of hydration products of dry-mixed mortar were analyzed, and the maximum substitution rate of RP was determined. Under the condition that the amount of cementitious material is 400 kg/m3 and the RP is at the maximum replacement rate, three different aggregate combinations to prepare concrete are the 100% use of SCRCA and SCRFA, PSRCA and PSRFA, and RS and natural aggregate (NCA); the workability, mechanical properties, and aggregate interface transition zone of the prepared concrete were analyzed. The results show that when the replacement rate of RP is less than 20%, it has little effect on the properties of products. The performance of PSRCA and PSRFA after treatment is better than that of SCRCA and SCRFA. Under different RP substitution rates, the performance of dry-mixed mortar prepared with PSRFA is very close to that prepared with RS. The performance of recycled concrete prepared with PSRCA and PSRFA is also very close to that of products prepared with NCA and RS. The failure morphology of PSRCA and RSRFA concrete is also similar to that of NCA and RS concrete.