Current Organizations / Institutes

The organizations/institutes from the scholar's latest article


Mustafa Koçer has a total of 29 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Impact of different cold joints on corrosion vulnerability and structural behavior of reinforced concrete beams with microscale insights

    by Alptuğ Ünal, Mustafa Koçer, Oğuzhan Öztürk

    Delays during concrete casting may form cold joints resulting in weak interfaces, increasing permeability and compromising the structural performance of reinforced concrete members. This study examines how different cold joint configurations affect the corrosion vulnerability and structural response of reinforced concrete beams. Beams with cold joints, both with and without adherence enhancers at the joint interfaces, were fabricated to evaluate the impact on corrosion extent. Microscale deterioration at the steel and concrete interface was investigated by SEM/EDS analyses. Among the specimens tested, the RBS-C beam, which contained a diagonal cold joint in the shear span, showed the largest reductions in load-carrying capacity and ductility and exhibited a brittle shear failure under the adopted corrosion and loading conditions. Although the horizontal joint at mid-span performed better than the diagonal shear region joint, it still showed considerable degradation. Microscale observations confirmed more severe chloride-induced corrosion and localized pitting in the diagonally jointed specimens. The outcomes of the study demonstrate how different cold joint configurations interact with corrosion processes and influence the durability and structural performance of reinforced concrete beams. Within the tested conditions, the results show how joint location and corrosion influenced the failure behavior and suggest that unplanned cold joints in regions of high shear demand warrant particular attention in chloride-exposed reinforced concrete members.

  • Impact of the Code-Based Near-Fault Factor on Buried Steel Pipelines via the Design Response Spectrum: Seydişehir–Ermenek Case Study

    by Mustafa Koçer

    This study investigates the influence of the code-based near-fault factor on the seismic response of buried steel natural-gas pipelines through the design response spectrum approach prescribed in the Turkish Seismic Code for Pipeline Systems and Liquid Storage Tanks (2023). The novelty lies in explicitly incorporating both the maximum-direction and near-fault factors into a spectrum-based finite element assessment and quantitatively evaluating their effects on displacement- and stress-based seismic demands. A planned pipeline route between Seydişehir (Konya) and Ermenek (Karaman), Türkiye, was selected as a case study, and seismic hazard parameters were obtained from the Turkish Seismic Hazard Map. The pipeline was modeled using four-node shell elements, while soil–pipe interaction was represented by linear elastic Winkler springs. Response-spectrum analyses were performed for DD-1, DD-1a, DD-2, and DD-3 ground-motion levels. For the DD-1 level including the near-fault factor, the maximum vertical displacement reached 10.42 mm, and the maximum axial membrane stress was approximately 62 MPa. The inclusion of the near-fault factor increased the maximum vertical displacement by 41% and raised the axial strain and membrane force demands by about 30%. The results demonstrate that neglecting this factor may lead to unconservative estimates of deformation demands in buried steel pipelines near active faults.

  • Behavior of corroded RC beams with varying corrosion percentages and shear reinforcement ratio under impact load

    by Mustafa Koçer, Ahmet Raif Boğa, Tolga Yılmaz, Hakan Erol, H. Selim Şengel, Özgür Anil, Ahmet Muhammed Uludoğan

    This study aims to experimentally and numerically investigate the behavior of reinforced concrete (RC) beams designed to exhibit flexure and shear failure behavior by changing the shear reinforcement ratio, which has undergone different corrosion rates under the effect of impact loading. Corrosion is the damage type that affects RC members the most throughout their economic life due to environmental conditions. Studies in literature examine the behavior of corroded RC beams under the effect of static and reversible repeated dynamic loads such as earthquakes or wind. However, the literature does not present a comprehensive experimental study examining the behavior of corroded RC beams under the effect of sudden dynamic impact loads. The planned study selects the corrosion percentage of RC beams and the status of exhibiting shear or flexural failure as experimental variables in a design approach. Acceleration, displacement, and loading time changes under the impact loading applied to corroded RC beams are measured and evaluated with the authors’ free weight drop test setup. The beams’ collapse mechanisms and energy dissipation capacities are interpreted, and the effects of corrosion on the behavior of the beams under the impact loading are investigated. The results obtained from the experimental part of the study and the numerical analysis results performed with the Ls-Dyna finite element software are compared, and the extent to which successful FEA analyses could be obtained is interpreted. It is observed that the corrosion occurring in RC beams negatively affected behavior under the impact loading significantly, reduced the maximum acceleration values measured from the beams by an average of 118%, and increased the maximum displacement and permanent residual displacement values occurring under the applied impact loading effect by an average of 142% and 167%, respectively. Corrosion also negatively affected the energy dissipation capacities of RC beams under the impact loading effect significantly and caused an average decrease of 81%.


  • An improved finite element code for assessment of corroded reinforced concrete beams subjected to impact loading

    by Mustafa Koçer, Ömer Mercimek, Gamze Nur Çolak, Ahmet Muhammed Uludoğan, Tolga Yılmaz


  • Open Access

    Enhancing the Capacity of Wide-Span Steel Frames Using External Post-Tensioning Cables

    by Mustafa Koçer, Hüseyin Şen

    Steel portal frames are widely used in industrial buildings due to their high strength-to-weight ratio and rapid erection capability. However, many existing structures exhibit insufficient load-carrying capacity under current design requirements. This study investigates the use of external post-tensioning (PT) cables and rigid wedge anchorages to enhance the overall performance of steel portal frames. Two stages of numerical analysis were performed: (i) two-dimensional parametric studies to identify the most efficient configuration and (ii) three-dimensional verification under combined gravity, wind, and seismic loading conditions. Results show that the proposed PT system significantly increases the load-carrying capacity of both beams and columns, reduces bending demands, and improves global stability without major geometric modification. The strengthening method is safe, reversible, and offers a practical alternative to conventional welded or plated retrofit techniques.

  • Open Access

    Çeşitli Parametrelerin Betonun Mekanik Özelliklerine Etkisinin Taguchi Yöntemi Kullanılarak Araştırılması

    by Kemal Uray, Hicran Açikel, Mustafa Koçer, Esra Uray

    Bu çalışma kapsamında, beton karışımlarının optimizasyonu için çeşitli parametrelerin etkisi incelenmiş ve bu amaçla istatistiksel temelli Taguchi yöntemi kullanılmıştır. Araştırma, sürdürülebilir, ekonomik ve üretim süresi açısından verimli bir beton tasarımının oluşturulmasını hedeflemiştir. Silis dumanı (SD), yüksek fırın cürufu (YFC), su/bağlayıcı oranı (S/B), çimento dozajı ve kalsiyum nitrit (DCI) gibi parametrelerin farklı seviyelerinin yer aldığı toplam 17 farklı karışım hazırlanmıştır. Bu karışımlar üzerinden basınç dayanımı ve eğilme dayanımı özelliklerini belirlemek amacıyla her seriden 3 tekrarlı örnekler üretilmiştir. Üretilen numuneler, 7, 28 ve 56 günlük standart kür sürelerinin ardından eğilme ve basınç dayanımı testlerine tabi tutulmuştur. Elde edilen deney sonuçları, Taguchi yöntemi çerçevesinde istatistiksel analizlere tabi tutulmuş ve parametrelerin optimum seviyeleri belirlenmiştir. Bu belirlenen optimum parametre seviyelerinde karışımlar üretilerek doğrulama deneyleri gerçekleştirilmiştir. Yapılan deneylerin sonuçları, çimento tüketimini minimize eden, atık ve kimyasal malzemeleri kullanarak betonun sürdürülebilirlik performansını artıran ve aynı zamanda ekonomik açıdan hızlı bir değerlendirmenin mümkün olduğunu göstermiştir.

  • Open Access

    İnşaat Mühendisliği Deneysel ve Analitik Tasarımlarında Taguchi Yönteminin Kullanılabilirliğinin Araştırılması

    by Kemal Uray, Mustafa Koçer, Esra Uray, Hicran Açikel

    Küresel ısınma, dünya üzerindeki tüm canlıları etkileyen en önemli çevre sorunlarından biridir. Karbondioksit (CO2) gibi sera gazlarının atmosfere salınması küresel ısınmada önemli rol oynamaktadır. Dünya çapında yapıların inşası için her yıl büyük miktarda çimento üretilmektedir. Çimento üretiminden kaynaklı olarak atmosferde önemli ölçüde (%15-24) CO2 gazı oluşmaktadır. Bu nedenle çimento yerine daha çevreci, sürdürülebilir malzemelerin belirli oranlarda kullanılması çevresel sürdürülebilirlik açısından önemlidir. İnşaat mühendisliği alanında özellikle beton üretimi ve zemin iyileştirmede yoğun bir şekilde kullanılan çimento yerine bu malzemelerin ikame edilmesi durumunda, sürdürülebilir malzemeler de dayanım ve durabilite özelliklerini olumlu yönde etkilemelidir. İnşaat mühendisliğinde, deneysel ve analitik çalışmalarda birçok parametre etkili olabilmektedir. Uçucu kül, silis dumanı ve öğütülmüş yüksek fırın cürufu gibi malzemeler kullanarak sürdürülebilir geopolimer betonların üretiminde optimum mineral katkı miktarını belirlemek veya bu parametrelerin istenilen beton özelliklerine etkisini araştırmak için birçok deney yapılması gerekmektedir. Diğer yandan birçok parametrenin etkili olduğu analitik çalışmalarda ise çok sayıda analize ihtiyaç duyulmaktadır. Japon bilim insanı Dr. Genichi Taguchi tarafından geliştirilen ve kalite iyileştirmede kullanılan yöntem sayesinde birçok parametrenin ve bu parametre seviyelerinin hedeflenen tasarım üzerindeki etkisi güvenilir bir şekilde belirlenebilmekte ve parametre optimizasyonu sağlam bir şekilde yapılabilmektedir. Yöntem sayesinde zamandan, iş gücünden, maliyetten ve enerjiden tasarruf sağlanarak güvenilir sonuçlar elde edilmektedir.

  • Open Access

    RC Structural Damages Observed After 30.10.2020 Seferihisar-İZMİR Earthquake and Analytical Evaluation Existing Sample RC Buildings

    by Mustafa Koçer, Alptuğ ÜNAL

    In Turkey, the İzmir Earthquake with Mw = 6.9 moment magnitude with the epicenter 17.26 km off the Seferihisar (İzmir) coast in the Aegean Sea occurred in 30th October 2020 at Turkish time 14.51. According to the acceleration records of İzmir earthquake, the recorded peak ground acceleration (PGA) was approximately 0.182g, and 117 deaths occurred in this earthquake, while 1032 people were injured. In this study, the structural damages occurred on the buildings due to the İzmir Earthquake were examined and discussed in details according to the current and former Turkish regulations. Moreover, a RC building constructed in 1998 and survived the earthquake without any permanent damage (a 5-storey building designed as 3-storey in the existing static project but added 2 more floors without any in-situ strengthening) was subjected to pushover analysis, linear analyses considering regulations and nonlinear time history pushover analysis according to the acceleration records of İzmir Earthquake. The obtained structural results were compared and discussed according to the current and former regulations.