Zijian Zhang
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Zijian Zhang has a total of 8 co-authors. Here are the top co-authors by number of shared publications:
- Aiguo Patrick Hu
University of Auckland
1 shared publication - Bassem Andrawes
Univ. of Illinois Urbana-Champaign
1 shared publication - Chongyuan Ma
Department of Automation, Nanjing University of Posts and Telecommunications, Nanjing, China
1 shared publication Daniel A. Kuchma
Department of Civil and Environmental Engineering, Tufts University, Medford, MA, USA
1 shared publication- J. Riley Edwards
University of Illinois at Urbana-Champaign
1 shared publication - Liang Huang
Department of Electrical and Electronic Engineering, University of Nottingham Ningbo China, Ningbo, China
1 shared publication
Latest Publications
- 21 July 2021
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Industrial Electronics
- Vol. 69 (7) , 6881-6891
Redefining the Channel Bandwidth for Simultaneous Wireless Power and Information Transfer
The ideal simultaneous wireless power and information transfer (SWPIT) system should share the same source and channel bandwidth. However, the requirements of the channel bandwidth between wireless power transfer (WPT) and wireless information transfer are different. In order to alleviate the effect of communications on the WPT, three bandwidths are redefined based on traditional communication systems, namely the modulation bandwidth, channel bandwidth and demodulation bandwidth. A square wave circuit is built to track the frequencies of signals at the receiver power coil, and the harmonic components in the same square wave are used to recreate information source to transmit data. Since the harmonic components can enlarge the deviations of the fundamental component, the needed channel bandwidth is decreased. The transmitter power coil and the receiver power coil still work under the quasi-resonant state with online communications. The communication function shows a strong immunity to various disturbances, such as distances, loads and input voltages. Based on the proposed method, two typical SWPIT systems in near-field and far-field are built, and the experimental data are consistent with the analytical results. The proposed SWPIT achieves a good tradeoff between efficiency and data transfer rate.
- 21 July 2021
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Industrial Electronics
- Vol. 69 (7) , 6881-6891
Redefining the Channel Bandwidth for Simultaneous Wireless Power and Information Transfer
The ideal simultaneous wireless power and information transfer (SWPIT) system should share the same source and channel bandwidth. However, the requirements of the channel bandwidth between wireless power transfer (WPT) and wireless information transfer are different. In order to alleviate the effect of communications on the WPT, three bandwidths are redefined based on traditional communication systems, namely the modulation bandwidth, channel bandwidth and demodulation bandwidth. A square wave circuit is built to track the frequencies of signals at the receiver power coil, and the harmonic components in the same square wave are used to recreate information source to transmit data. Since the harmonic components can enlarge the deviations of the fundamental component, the needed channel bandwidth is decreased. The transmitter power coil and the receiver power coil still work under the quasi-resonant state with online communications. The communication function shows a strong immunity to various disturbances, such as distances, loads and input voltages. Based on the proposed method, two typical SWPIT systems in near-field and far-field are built, and the experimental data are consistent with the analytical results. The proposed SWPIT achieves a good tradeoff between efficiency and data transfer rate.
- 9 October 2015
- Published by Taylor & Francis in International Journal of Rail Transportation
- Vol. 4 (1) , 1-19
Numerical and experimental study on dynamic behaviour of concrete sleeper track caused by wheel flat
Impact loads caused by flat spots on railcar wheels impose a major maintenance burden on railroads and can cause severe damage to both railcar and track components. This paper discusses the dynamic behaviour of the railroad track system under impact loads. A finite element (FE) model with multiple crossties and their accompanying fastening systems is developed and validated using field data. The results of the parametric study indicate that impact loading consists of direct wheel impact loads and track system vibration–induced impact loads. Both of these impact mechanisms are sensitive to the stiffness of rail pad. It is observed that rail pad with a moderate stiffness provides the most effective impact attenuation.
- 9 October 2015
- Published by Taylor & Francis in International Journal of Rail Transportation
- Vol. 4 (1) , 1-19
Numerical and experimental study on dynamic behaviour of concrete sleeper track caused by wheel flat
Impact loads caused by flat spots on railcar wheels impose a major maintenance burden on railroads and can cause severe damage to both railcar and track components. This paper discusses the dynamic behaviour of the railroad track system under impact loads. A finite element (FE) model with multiple crossties and their accompanying fastening systems is developed and validated using field data. The results of the parametric study indicate that impact loading consists of direct wheel impact loads and track system vibration–induced impact loads. Both of these impact mechanisms are sensitive to the stiffness of rail pad. It is observed that rail pad with a moderate stiffness provides the most effective impact attenuation.