AMAnjibabu Merneedi

Anjibabu Merneedi

*This is an algorithmically generated author record based on publicly available information.

Anjibabu Merneedi has a total of 28 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Prediction of drivers’ impact on green supply chain management using deep learning algorithm

    by Anjibabu Merneedi, Ramesh Palisetty

    Nowadays, for controlling the organizations’ environmental impact and attaining performance enhancement in industries, green supply chain management (GSCM) plays a significant role. This work considers four major drivers and five primary dimensions for the deployment of GSCM systems in industries. The five primary dimensions are consumer intrusiveness, restructuring quality of supply chain, risk and security consciousness, and urbanization in the region leather industry, and the four major drivers are the effectiveness, features, significance, and limitations of the restructured GSCM system. Additionally, this paper investigates the primary factors that are used for deploying the GSCM system in leather industries located in the northern part of Tamil Nadu. Initially, the survey questions are prepared based on the concept and distributed to the authorities of industries. For the survey questions provided to various industries, three leather industries properly answered all the questions. Each question is mandatory. Then, the collected data were analyzed using the deep belief network (DBN) to measure the impact of primary drivers in implementing the GSCM system in industries. The performance of the proposed system is analyzed with various existing methods in terms of accuracy, precision, f-measure, etc. The proposed framework’s implementation has implications for increasing organizational efficiency, lowering costs, minimizing waste, and encouraging green culture among personnel. This study will aid in the development of policies and a better knowledge of how to implement green innovation methods.


  • Retracted
    Open Access

    Investigation of Tribological Behaviour on DLC Coatings for AA5051 using DC Sputtering

    by L. Natrayan, Piyush Gaur, Anjibabu Merneedi, S. Kaliappan, Pravin P. Patil, V. Sivaprakash, Muse Degefe Chewaka

    DLC coatings are deposited on aluminium substrates to improve the wear resistance property of the substrates using sputtering deposition in this study. DLC coatings are deposited using the graphite target onto the Al5051 substrates using DC sputtering. The deposited coatings are then analyzed for their adhesion strength, hardness, coefficient of friction, and chemical compositions. The pin-on-disk method is conducted in vacuumed conditions, dry air conditions (0% RH), and ambient air conditions (40% RH). The different testing conditions have shown different results for the same testing sample. This indicates the nature of DLC film adsorption in ambient air conditions. The chemical composition study has further revealed the adsorbing compounds and the ability of hydrogen and water molecules to get adsorbed on the thin-film surface. This study gives insight into the effect of molecules present in the ambient air on the performance of DLC coatings. It investigates the effect of three DLC coatings deposited using the graphite target onto the Al5051 substrates using DC sputtering.


  • Open Access

    Processing and Characterization of Carbon Nanofibre Composites for Automotive Applications

    by L. Natrayan, Anjibabu Merneedi, G. Bharathiraja, S. Kaliappan, Dhinakaran Veeman, P. Murugan

    Currently, numerous studies have shown that carbon nanofibres have mechanical properties that are replaced by other widely used fibres. The high tensile strength of the carbon fibres makes them ideal to use in polymer matrix composites. The high-strength fibres can be used in short form in a composite and mass-produced to meet the high demands of automotive applications. These composites are capable of addressing the strength requirement of nonstructural and structural components of the automotive industry. Due to these composite lightweight and high-strength weight ratios, the applications can be widely varying. The research for these materials is a never-ending process, as researchers and design engineers are yet to tap its full potential. This study fabricated phenolic resin with different wt% of carbon nanofibre (CNF). The percentage of the CNF as a filler material is varied from 1 to 4 wt%. Mechanical properties such as hardness, tensile strength, and XRD were investigated. Phenolic resin with 4 wt% of carbon nanofibre (CNF) exhibits maximum tensile strength and hardness of 43.8 MPa and 37.8 HV.


  • Open Access

    Experimental Investigation on Mechanical Properties of Carbon Nanotube-Reinforced Epoxy Composites for Automobile Application

    by Anjibabu Merneedi, L. Natrayan, S. Kaliappan, Dhinakaran Veeman, S. Angalaeswari, Chidurala Srinivas, Prabhu Paramasivam

    Carbon nanotubes are established as a superior form of carbon. These have superior characteristics in terms of mechanical and chemical properties when compared to the other fibres available. High-strength fibres can be employed in a composite in a short form and mass-produced to fulfil high demands in composite applications. These composites can meet the strength requirements of nonstructural and structural components in a wide range of industries. Because of their light weight and excellent strength-to-weight ratio, these composites can be used in a wide range of applications. With Young’s modulus as high as 1 TPa and tensile strength up to 63 GPa, they are among the stiffest and strongest fibres. There is currently a lot of interest in using carbon nanotubes in a matrix to take advantage of these features. There have been a variety of polymer matrices used, and nanotube/ceramic and nanotube/metal composites are gaining popularity. The study of these materials is an ongoing process, as researchers and design engineers have yet to realize their full potential. Carbon nanotubes (CNTs) are used in this study to create the composite with the resin. The percentage of CNT used as a filler material in the composite is varied from 1 to 4 percent, with the best percentage chosen for optimal mechanical properties.


  • Open Access

    Evaluating the Mechanical and Tribological Properties of DLC Nanocoated Aluminium 5051 Using RF Sputtering

    by L. Natrayan, Anjibabu Merneedi, Dhinakaran Veeman, S. Kaliappan, P. Satyanarayana Raju, Ram Subbiah, S. Venkatesh Kumar

    The diamond-like carbon- (DLC-) coating technique is used in the sliding parts of automotive engines, among other applications, to reduce friction and wear. In this work, DLC has been coated on the Aluminium 5051 sample to assess the mechanical and tribological properties. A sputtering deposition mechanism is used, and the DLC is coated using a graphite target. The developed DLC coatings are tested for adhesion strength, hardness, chemical composition using XRD, and wear behaviour. The developed DLC thin films have considerably increased the wear behaviour of the Aluminium 5051 sample and have fulfilled the objective of this study. The XRD data indicated the presence of amorphous carbon in the coating with a threefold increase to the hardness of the naked aluminium. This study provides insight into improving the aluminium wear resistance by developing a considerably hard coating.


  • Open Access

    Synthesis and Characterization of Polypropylene/Ramie Fiber with Hemp Fiber and Coir Fiber Natural Biopolymer Composite for Biomedical Application

    by T. Sathish, Kumaran Palani, L. Natrayan, Anjibabu Merneedi, Melvin Victor De Poures, Dinesh Kumar Singaravelu

    In the current scenario, many natural fibers available in the world can be used in various applications in the day-to-day life of biomedical products, automobile parts, industrial products, etc. Biocomposites can replace or serve as a framework allowing the regeneration of traumatized, degenerated tissues, and organs, thus, improving the patients’ quality of life. This research work is aimed at fabricating and investigating the natural biopolymer composites for biomedical applications. There are two sets of fiber composites fabricated in this research work. Ramie fiber considers a common base fiber for both composites. Hemp fibers and coir fibers were considered as filler in this research work. Biodegradable and bioresorbable polypropylene resins are used to fabricate the biocomposite using the compression moulding technique. Different proportion specimen mechanical properties were compared for bone fixtures and joint applications. The contour plots and bar charts were plotted to identify the variations in the volume percentage. The individual fiber specimens also have significant properties when compared with the composite fibers. Then, the individual superior property-based combinations such as hemp and coir fiber mixed with biodegradable and bioresorbable polypropylene/ramie fiber were recommended to produce joints and bone fixtures to alleviate pain for patients.


  • Retracted
    Open Access

    [Retracted] Free Vibration Analysis of Thick Rectangular and Elliptical Plates with Concentric Cut‐Out

    by Anjibabu Merneedi, Nalluri Mohan Rao, L. Natrayan, L. Yuvaraj, Prabhu Paramasivam

    This research paper deals with a numerical method which is modified and applied, by the authors to derive an eigenvalue of a thick plate having cut‐out in which geometries of plate and cut‐outs are different, through a deflection matching condition by including shear deformation and rotary inertia effects, with less computational efforts and high accuracy. The modified Independent Coordinate Coupling Method (ICCM) is validated with FEM package (ANSYS) and applied to know the change in eigenvalues for a plate with cut‐out by varying various parameters like aspect ratios, cut‐out size, and thickness ratios. Trigonometric functions considered at the boundary level conditions of a simply supported plate should be satisfied. Free vibrational exploration on a thick isotropic plate with various aspect ratios and an elliptical plate with various sizes is carried out through the modified ICCM. Independent coordinates are applied for a plate domain and for a hole domain individually followed by equating the deflection condition of hole and plate, a reduced mass to express with cut‐out from which eigenvalues can be obtained. The deflection matching condition facilitates the analysis even though the geometries of plate and cut‐outs are different.


  • Retracted
    Open Access

    [Retracted] Improvement on Mechanical Properties of Submerged Friction Stir Joining of Dissimilar Tailor Welded Aluminum Blanks

    by R. Suryanarayanan, V. G. Sridhar, L. Natrayan, S. Kaliappan, Anjibabu Merneedi, T. Sathish, Alazar Yeshitla

    Friction stir welding is a solid‐state welding method that produces joints with superior mechanical and metallurgical properties. However, the negative effects of the thermal cycle during welding dent the mechanical performance of the weld joint. Hence, in this research study, the joining of aluminum tailor welded blanks by friction stir welding is carried out in underwater conditions by varying the welding parameters. The tensile tests revealed that the underwater welded samples showed better results when compared to the air welded samples. Maximum tensile strength of 229.83 MPa was obtained at 1000 rpm, 36 mm/min. The improved tensile strength of the underwater welded samples was credited to the suppression of the precipitation of the secondary precipitates due to the cooling action provided by the water. The lowest hardness of 72 HV was obtained at the edge of the stir zone which indicated the weakest region in the weld zone.