Jerzy Sobczak
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Research Interests
Jerzy Sobczak has a total of 103 co-authors. Here are the top co-authors by number of shared publications:
- Natalia Sobczak
Institute of Metallurgy and Materials Science, Polish Academy of Sciences, Krakow, 30-418, Poland
25 shared publications Ludmil Drenchev
6 shared publications- Martah Homa
Foundry Research Institute
6 shared publications - Rafal Nowak
Foundry Research Institute, Krakow, Poland
6 shared publications Savko Malinov
Queen ' s University|School of Mechanical and Aerospace Engineering
6 shared publications- Sylwia Terlicka
Institute of Metallurgy and Materials Science, Polish Academy of Sciences, Kraków, Poland
6 shared publications
Latest Publications
- Open Access
- 23 September 2026
- Published by Elsevier in SSRN Electronic Journal
Liquid-assisted in-situ synthesis of TiC during high-temperature interaction between remelted gray cast iron and pure titanium
The wetting and reactive infiltration behavior of remelted gray cast iron (GCI) on compacted Ti powder was investigated using real-time sessile-drop observations with non-contact heating. Molten GCI showed spontaneous reactive wetting (contact angle ranged from 5 to 30°), rapid melt penetration into the Ti substrate, and bubble-induced oscillations tentatively associated with carbothermal reduction of TiOx. Microstructural analyses (LM, STEM-HAADF, EDS, TEM/SADP) confirmed in-situ formation of TiC, together with FeTi, Fe2Ti and locally Ti5Si3 as reaction products in the Fe–Ti–C–Si system. Reactive infiltration produced a TiC-rich transition zone shaped by coupled chemical and gas-evolution processes. The findings demonstrate the potential of GCI/Ti systems for cost-effective fabrication of TiC-reinforced MMCs with tailored microstructures and improved high-temperature stability.
- 23 September 2026
- Published by Elsevier in SSRN Electronic Journal
Open AccessLiquid-assisted in-situ synthesis of TiC during high-temperature interaction between remelted gray cast iron and pure titanium
The wetting and reactive infiltration behavior of remelted gray cast iron (GCI) on compacted Ti powder was investigated using real-time sessile-drop observations with non-contact heating. Molten GCI showed spontaneous reactive wetting (contact angle ranged from 5 to 30°), rapid melt penetration into the Ti substrate, and bubble-induced oscillations tentatively associated with carbothermal reduction of TiOx. Microstructural analyses (LM, STEM-HAADF, EDS, TEM/SADP) confirmed in-situ formation of TiC, together with FeTi, Fe2Ti and locally Ti5Si3 as reaction products in the Fe–Ti–C–Si system. Reactive infiltration produced a TiC-rich transition zone shaped by coupled chemical and gas-evolution processes. The findings demonstrate the potential of GCI/Ti systems for cost-effective fabrication of TiC-reinforced MMCs with tailored microstructures and improved high-temperature stability.
- Open Access
- 18 September 2026
- Published by Polish Academy of Sciences Chancellery in Archives of Metallurgy and Materials
- Vol. 71 (3) , 751-763
High-temperature interactions between molten Mg-10Ca alloy with Ti substrate under different atmospheric conditions
This work investigates the combined effects of atmosphere and alloying with calcium on the high-temperature interaction between a molten Mg-10Ca alloy and a polished titanium substrate. The sessile drop method was employed with non-contact heating and capillary purification, enabling the generation of an oxide-free Mg-10Ca drop. Experiments were conducted isothermally at 700°C under two flowing atmospheres: (i) pure Ar and (ii) Ar + 5 wt.% H2. In pure Ar, the evolution of the average contact angle results from both evaporation of the oxide-free Mg-10Ca alloy and chemical interaction between Mg-Ca vapor and the oxidized Ti surface. Initially, non-wetting behavior (θ > 90°) was observed. A non-wetting-to-wetting transition occurred at ~200 s (θ = 90°), followed by progressive improvement in wettability, reaching an average final contact angle of ~70° at 300 s. SEM/BSE/EDS analysis of the Mg-10Ca/Ti couple formed in pure Ar revealed interfacial discontinuities, absence of permanent bonding, and pronounced triple-line pinning, which led to an asymmetric drop geometry arising from the inhomogeneous structure and chemistry of the Ti surface. In contrast, excellent wettability and bonding were obtained under the Ar + 5 wt.% H2 atmosphere. Under identical testing conditions, the contact angle decreased rapidly from 19° to 11° within ~50 s and remained nearly constant during holding at 700 °C up to 300 s, with a final contact angle of ~9° at the end of the test. The results of structural characterization suggest that the remarkable improvement in wettability arises from the synergistic effect of several factors: (1) alloying magnesium with calcium, (2) presence of hydrogen in the surrounding atmosphere, (3) the evaporation of both Mg and Ca from the drop and (4) the enhanced chemical interaction between the Mg-Ca alloy and the Ti substrate in the presence of hydrogen.
- 18 September 2026
- Published by Polish Academy of Sciences Chancellery in Archives of Metallurgy and Materials
- Vol. 71 (3) , 751-763
Open AccessHigh-temperature interactions between molten Mg-10Ca alloy with Ti substrate under different atmospheric conditions
This work investigates the combined effects of atmosphere and alloying with calcium on the high-temperature interaction between a molten Mg-10Ca alloy and a polished titanium substrate. The sessile drop method was employed with non-contact heating and capillary purification, enabling the generation of an oxide-free Mg-10Ca drop. Experiments were conducted isothermally at 700°C under two flowing atmospheres: (i) pure Ar and (ii) Ar + 5 wt.% H2. In pure Ar, the evolution of the average contact angle results from both evaporation of the oxide-free Mg-10Ca alloy and chemical interaction between Mg-Ca vapor and the oxidized Ti surface. Initially, non-wetting behavior (θ > 90°) was observed. A non-wetting-to-wetting transition occurred at ~200 s (θ = 90°), followed by progressive improvement in wettability, reaching an average final contact angle of ~70° at 300 s. SEM/BSE/EDS analysis of the Mg-10Ca/Ti couple formed in pure Ar revealed interfacial discontinuities, absence of permanent bonding, and pronounced triple-line pinning, which led to an asymmetric drop geometry arising from the inhomogeneous structure and chemistry of the Ti surface. In contrast, excellent wettability and bonding were obtained under the Ar + 5 wt.% H2 atmosphere. Under identical testing conditions, the contact angle decreased rapidly from 19° to 11° within ~50 s and remained nearly constant during holding at 700 °C up to 300 s, with a final contact angle of ~9° at the end of the test. The results of structural characterization suggest that the remarkable improvement in wettability arises from the synergistic effect of several factors: (1) alloying magnesium with calcium, (2) presence of hydrogen in the surrounding atmosphere, (3) the evaporation of both Mg and Ca from the drop and (4) the enhanced chemical interaction between the Mg-Ca alloy and the Ti substrate in the presence of hydrogen.
- Open Access
- 18 September 2026
- Published by Polish Academy of Sciences Chancellery in Archives of Metallurgy and Materials
- Vol. 71 (3) , 709-722
A Brief History of Metal Casting from the Creative Fire to the Science of High-Temperature Wettability
This essay offers an interdisciplinary synthesis of the historical and modern foundations of metal casting, linking its mythological origins with contemporary surface physics and hydrodynamics. It proposes a new conceptual framework in which wettability is treated as a dynamic, temperature- and composition-dependent boundary condition for the Navier-Stokes equations rather than a static property. The limitations of the classical Young’s equation under high-temperature, reactive, and transient foundry conditions are highlighted, and an extended formulation incorporating vertical interfacial forces and a capillary contact-line term is introduced. Dimensionless numbers governing thin-film flow, mold filling, and defect formation are discussed to emphasize the hydrodynamic relevance of dynamic wettability. The essay argues that future advances in metal casting science should integrate coupled flow-surface energy models with predictive tools such as numerical simulation, additive manufacturing, and AI-based optimization, offering a unified perspective on liquid metal behavior at solid-gas interfaces.
- 18 September 2026
- Published by Polish Academy of Sciences Chancellery in Archives of Metallurgy and Materials
- Vol. 71 (3) , 709-722
Open AccessA Brief History of Metal Casting from the Creative Fire to the Science of High-Temperature Wettability
This essay offers an interdisciplinary synthesis of the historical and modern foundations of metal casting, linking its mythological origins with contemporary surface physics and hydrodynamics. It proposes a new conceptual framework in which wettability is treated as a dynamic, temperature- and composition-dependent boundary condition for the Navier-Stokes equations rather than a static property. The limitations of the classical Young’s equation under high-temperature, reactive, and transient foundry conditions are highlighted, and an extended formulation incorporating vertical interfacial forces and a capillary contact-line term is introduced. Dimensionless numbers governing thin-film flow, mold filling, and defect formation are discussed to emphasize the hydrodynamic relevance of dynamic wettability. The essay argues that future advances in metal casting science should integrate coupled flow-surface energy models with predictive tools such as numerical simulation, additive manufacturing, and AI-based optimization, offering a unified perspective on liquid metal behavior at solid-gas interfaces.
- Open Access
- 5 May 2026
- Published by Elsevier in SSRN Electronic Journal
Wettability behavior and interfacial reactions of liquid pure Al and Al-7Si alloy with Ti+C compacted substrate
The study investigates the high‑temperature interaction between liquid Al and Al-7Si alloy and a compacted Ti+C substrate using the sessile drop method with non‑contact heating and capillary purification at 800 °C under high vacuum. Both Al/Ti+C and Al-7Si/Ti+C systems initially exhibited non-wetting behavior (40 s and 150 s, respectively), followed by reactive wetting, with contact angles decreasing to 40° for Al and 60° for Al-7Si. The transition is governed by reaction-controlled spreading at the drop/substrate interface. SEM and TEM analyses revealed that interfacial reactions are dominated by Al-Ti and Al-Ti-Si phase formation. TiAl3 formed in the Al/Ti+C couple, while the Al-7Si/Ti+C system produced Si-enriched α-Ti and Ti(Al,Si)3, explaining the ~550 s delay in spreading. Localized TiC formation occurred due to transient thermal fluctuations enabling short-range Ti-C diffusion. Additionally, oxide films were shown to significantly influence high‑temperature wettability behavior.
- 5 May 2026
- Published by Elsevier in SSRN Electronic Journal
Open AccessWettability behavior and interfacial reactions of liquid pure Al and Al-7Si alloy with Ti+C compacted substrate
The study investigates the high‑temperature interaction between liquid Al and Al-7Si alloy and a compacted Ti+C substrate using the sessile drop method with non‑contact heating and capillary purification at 800 °C under high vacuum. Both Al/Ti+C and Al-7Si/Ti+C systems initially exhibited non-wetting behavior (40 s and 150 s, respectively), followed by reactive wetting, with contact angles decreasing to 40° for Al and 60° for Al-7Si. The transition is governed by reaction-controlled spreading at the drop/substrate interface. SEM and TEM analyses revealed that interfacial reactions are dominated by Al-Ti and Al-Ti-Si phase formation. TiAl3 formed in the Al/Ti+C couple, while the Al-7Si/Ti+C system produced Si-enriched α-Ti and Ti(Al,Si)3, explaining the ~550 s delay in spreading. Localized TiC formation occurred due to transient thermal fluctuations enabling short-range Ti-C diffusion. Additionally, oxide films were shown to significantly influence high‑temperature wettability behavior.
- 22 December 2025
- Published by Polish Academy of Sciences Chancellery in Archives of Metallurgy and Materials
- p. 2033-2042
A Novel Stepwise Thermal Protocol for Sessile Drop Wetting Tests of Liquid Lead and Refractory Metals for Nuclear Applications
By applying the sessile drop method, a novel procedure for testing the physicochemical interaction between liquid metals and refractory solid metals used in nuclear reactors was developed. It involves two methodological approaches: (1) in situ surface purification of liquid metal drops from its native oxide film directly in a vacuum chamber, by squeezing liquid metal from a capillary placed above the tested substrate, and (2) cyclical and stepped temperature change involving stepwise heating from 400 to 600°C, followed by cooling back to 400°C using two separate protocols (i) a single heating cycle from 400 to 600°C, followed by gradual cooling to 400°C, and (ii) a repetitive cycle involving heating from 400 to 600°C, cooling to 400°C, reheating directly to 600°C, and final cooling to 400°C. Wettability tests of selected refractory metal substrates (Me = Mo, Ta, and Ti) with liquid Pb using the sessile drop method and a new procedure showed that the wetting kinetics and contact angle of Pb/Me couples are significantly affected by temperature, but only during the gradual heating up to a maximum of 600°C. During the subsequent steps to final cool down to 400°C, the contact angle for all tested Pb/Me couples remains unchanged. Measurement discrepancies were observed depending on the capillary materials used (graphite vs. alumina) and surface conditions (polished vs. ground). The results indicate that under the investigated conditions, liquid Pb does not wet the Mo substrate (with increase in temperature, θPb/Mo ~ 115-100°), shows weak wetting on the Ta substrate (θPb/Ta ~ 87-84°), better wetting on polished Ti (θPb/Ti = 30° and θPb/Ti = 67°, with graphite and alumina capillaries, respectively), and good wetting on rough, ground, and unpolished Ti substrate (θPb/Ti_unpolished = 28°).
- 22 December 2025
- Published by Polish Academy of Sciences Chancellery in Archives of Metallurgy and Materials
- p. 2033-2042
A Novel Stepwise Thermal Protocol for Sessile Drop Wetting Tests of Liquid Lead and Refractory Metals for Nuclear Applications
By applying the sessile drop method, a novel procedure for testing the physicochemical interaction between liquid metals and refractory solid metals used in nuclear reactors was developed. It involves two methodological approaches: (1) in situ surface purification of liquid metal drops from its native oxide film directly in a vacuum chamber, by squeezing liquid metal from a capillary placed above the tested substrate, and (2) cyclical and stepped temperature change involving stepwise heating from 400 to 600°C, followed by cooling back to 400°C using two separate protocols (i) a single heating cycle from 400 to 600°C, followed by gradual cooling to 400°C, and (ii) a repetitive cycle involving heating from 400 to 600°C, cooling to 400°C, reheating directly to 600°C, and final cooling to 400°C. Wettability tests of selected refractory metal substrates (Me = Mo, Ta, and Ti) with liquid Pb using the sessile drop method and a new procedure showed that the wetting kinetics and contact angle of Pb/Me couples are significantly affected by temperature, but only during the gradual heating up to a maximum of 600°C. During the subsequent steps to final cool down to 400°C, the contact angle for all tested Pb/Me couples remains unchanged. Measurement discrepancies were observed depending on the capillary materials used (graphite vs. alumina) and surface conditions (polished vs. ground). The results indicate that under the investigated conditions, liquid Pb does not wet the Mo substrate (with increase in temperature, θPb/Mo ~ 115-100°), shows weak wetting on the Ta substrate (θPb/Ta ~ 87-84°), better wetting on polished Ti (θPb/Ti = 30° and θPb/Ti = 67°, with graphite and alumina capillaries, respectively), and good wetting on rough, ground, and unpolished Ti substrate (θPb/Ti_unpolished = 28°).
- Open Access
- 1 March 2025
- Published by KEAI Publishing in Journal of Magnesium and Alloys
- Vol. 13 (3) , 1149-1159
Wetting behavior of Mo, Ta, and stainless steel substrates in contact with molten Mg
- 1 March 2025
- Published by KEAI Publishing in Journal of Magnesium and Alloys
- Vol. 13 (3) , 1149-1159
Open AccessWetting behavior of Mo, Ta, and stainless steel substrates in contact with molten Mg
- 19 February 2024
- Published by Elsevier in Ceramics International
- Vol. 50 (10) , 17452-17464
Production of metal matrix composite reinforced by TiC by reactive infiltration of cast iron into Ti + C preforms
- 19 February 2024
- Published by Elsevier in Ceramics International
- Vol. 50 (10) , 17452-17464
Production of metal matrix composite reinforced by TiC by reactive infiltration of cast iron into Ti + C preforms
- Open Access
- 1 February 2024
- Published by KEAI Publishing in Journal of Magnesium and Alloys
- Vol. 12 (2) , 659-672
Wettability, reactivity, and interface structure in Mg/Ni system
- 1 February 2024
- Published by KEAI Publishing in Journal of Magnesium and Alloys
- Vol. 12 (2) , 659-672
Open AccessWettability, reactivity, and interface structure in Mg/Ni system
- 1 February 2022
- Published by Elsevier in Materials Letters
- Vol. 309, 131399
Improvement of TiC/Fe in situ composite layer formation on surface of Fe-based castings
- 1 February 2022
- Published by Elsevier in Materials Letters
- Vol. 309, 131399
Improvement of TiC/Fe in situ composite layer formation on surface of Fe-based castings