Dileep Madapana
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Dileep Madapana has a total of 16 co-authors. Here are the top co-authors by number of shared publications:
- Jyotsna Dutta Majumdar
Department of Metallurgical & Materials Engineering, Indian Institute of Technology, Kharagpur, India
8 shared publications - Indranil Manna
Department of Metallurgical and Materials Engineering, Indian Institute of Technology Kharagpur, Kharagpur, India
4 shared publications - Ashish Kumar Nath
Department of Mechanical Engineering, Indian Institute of Technology Kharagpur, Kharagpur, India
3 shared publications - Harikrishnan Ramadas
GREMAN UMR CNRS 7347, Insa Centre Val de Loire, Université de Tours, Tours, France
3 shared publications Jyotsna Dutta Majumdar
2 shared publications- Ravi Bathe
Centre for Laser Processing of Materials, International Advanced Research Centre for Powder Metallurgy and New Materials (ARCI), Hyderabad, Telangana, India
2 shared publications
Latest Publications
- Open Access
- 4 August 2026
- Published by Elsevier in SSRN Electronic Journal
Femtosecond Laser-Induced Backward Transfer of Copper on Glass: Microstructural Evolution, Oxidation Behavior, and Conductivity Enhancement
Femtosecond laser-induced backward transfer (LIBT) offers a promising route for direct metallization of transparent substrates while limiting thermal damage, yet the conditions governing film continuity, oxidation state, and electrical behavior in copper deposits are not well established. Here, copper was transferred from a bulk donor onto ultra-clear soda-lime glass using a 1030 nm, 208 fs Yb-based solid-state laser, with donor-receiver gap, fluence, and scan speed systematically varied. Deposited films were characterized by SEM, 3D optical profilometry, Raman spectroscopy, XPS, and four-point probe resistivity measurements. A 40 µm donor-receiver gap yielded the most uniform, continuous coverage. Low fluence produced discontinuous nanoscale clusters, while higher fluence generated denser, continuous tracks, though with greater Cu2O and CuO alongside metallic copper, confirmed by Raman and XPS. Films combining continuous coverage with minimal oxidation showed the lowest as-deposited resistivity (23 × 10⁻⁵ Ω·cm), while discontinuous or heavily oxidized films showed markedly higher values. Subsequent annealing in 5% H2/Ar reduced the LIBT-formed oxides—verified via Raman, high-resolution XPS, and Cu LMM Auger analysis—and promoted grain coalescence, densifying the films and lowering resistivity further to 7.21 × 10⁻⁵ Ω·cm. These findings establish clear structure-property-process relationships for femtosecond LIBT of copper, supporting fabrication of high-quality, low-resistivity Cu films.
- 4 August 2026
- Published by Elsevier in SSRN Electronic Journal
Open AccessFemtosecond Laser-Induced Backward Transfer of Copper on Glass: Microstructural Evolution, Oxidation Behavior, and Conductivity Enhancement
Femtosecond laser-induced backward transfer (LIBT) offers a promising route for direct metallization of transparent substrates while limiting thermal damage, yet the conditions governing film continuity, oxidation state, and electrical behavior in copper deposits are not well established. Here, copper was transferred from a bulk donor onto ultra-clear soda-lime glass using a 1030 nm, 208 fs Yb-based solid-state laser, with donor-receiver gap, fluence, and scan speed systematically varied. Deposited films were characterized by SEM, 3D optical profilometry, Raman spectroscopy, XPS, and four-point probe resistivity measurements. A 40 µm donor-receiver gap yielded the most uniform, continuous coverage. Low fluence produced discontinuous nanoscale clusters, while higher fluence generated denser, continuous tracks, though with greater Cu2O and CuO alongside metallic copper, confirmed by Raman and XPS. Films combining continuous coverage with minimal oxidation showed the lowest as-deposited resistivity (23 × 10⁻⁵ Ω·cm), while discontinuous or heavily oxidized films showed markedly higher values. Subsequent annealing in 5% H2/Ar reduced the LIBT-formed oxides—verified via Raman, high-resolution XPS, and Cu LMM Auger analysis—and promoted grain coalescence, densifying the films and lowering resistivity further to 7.21 × 10⁻⁵ Ω·cm. These findings establish clear structure-property-process relationships for femtosecond LIBT of copper, supporting fabrication of high-quality, low-resistivity Cu films.
- 4 February 2025
- Published by Springer Nature in Journal of Materials Engineering and Performance
- Vol. 34 (18) , 21280-21296
Studies on Aluminum Cenosphere Composite Foam Developed by Plasma-Spray-Assisted Additive Manufacturing
- 4 February 2025
- Published by Springer Nature in Journal of Materials Engineering and Performance
- Vol. 34 (18) , 21280-21296
Studies on Aluminum Cenosphere Composite Foam Developed by Plasma-Spray-Assisted Additive Manufacturing
- 25 December 2024
- Published by Elsevier in Tribology International
- Vol. 204
Nanosecond laser shock peening of titanium alloys (Ti6Al4V) and its invitro-tribocorrosion behavior
- 25 December 2024
- Published by Elsevier in Tribology International
- Vol. 204
Nanosecond laser shock peening of titanium alloys (Ti6Al4V) and its invitro-tribocorrosion behavior
- 6 May 2024
- Published by Elsevier in Tribology International
- Vol. 197, 109711
Laser surface structuring of titanium alloy (Ti-6Al-4V) for improved tribocorrosion resistance for bio-implant applications
- 6 May 2024
- Published by Elsevier in Tribology International
- Vol. 197, 109711
Laser surface structuring of titanium alloy (Ti-6Al-4V) for improved tribocorrosion resistance for bio-implant applications
- 13 January 2024
- Published by Wiley in Physica Status Solidi (a)
- Vol. 221 (15)
Studies on Surface Characteristics and Biocorrosion Behavior of Ultrafast Laser‐Structured Titanium Alloy (Ti6Al4V)
Herein, the detailed corrosion behavior of ultrafast laser‐surface structured Ti6Al4V (using a Ti: Sapphire laser processed under optimum parameters) is carried out in simulated body fluid using electrochemical impedance spectroscopy and correlated with surface characteristics. Laser structuring leads to a topographically modified surface consisting of periodic surface patterns (nanoripples, nanodots) in the presence of a thin oxide layer. Surface processing introduces strain on the surface up to a depth of 150 μm, with the grains aligned along the and planes. The detailed electrochemical impedance spectroscopic studies show the formation of stable passive layers in surface‐structured Ti6Al4V as compared to as‐received Ti6Al4V.
- 13 January 2024
- Published by Wiley in Physica Status Solidi (a)
- Vol. 221 (15)
Studies on Surface Characteristics and Biocorrosion Behavior of Ultrafast Laser‐Structured Titanium Alloy (Ti6Al4V)
Herein, the detailed corrosion behavior of ultrafast laser‐surface structured Ti6Al4V (using a Ti: Sapphire laser processed under optimum parameters) is carried out in simulated body fluid using electrochemical impedance spectroscopy and correlated with surface characteristics. Laser structuring leads to a topographically modified surface consisting of periodic surface patterns (nanoripples, nanodots) in the presence of a thin oxide layer. Surface processing introduces strain on the surface up to a depth of 150 μm, with the grains aligned along the and planes. The detailed electrochemical impedance spectroscopic studies show the formation of stable passive layers in surface‐structured Ti6Al4V as compared to as‐received Ti6Al4V.
- 10 October 2022
- Published by Springer Nature in JOM
- Vol. 75 (1) , 109-119
Studies on Laser Shock Peening on Nanomechanical and Mechano-Chemical Properties of Titanium Alloy (Ti6Al4V)
- 10 October 2022
- Published by Springer Nature in JOM
- Vol. 75 (1) , 109-119
Studies on Laser Shock Peening on Nanomechanical and Mechano-Chemical Properties of Titanium Alloy (Ti6Al4V)
- 15 April 2022
- Published by Springer Nature in Transactions of the Indian National Academy of Engineering
- Vol. 7 (3) , 851-871
Short and Ultrashort Laser Surface Processing of Alpha + Beta Titanium Alloy (Ti6Al4V): Present Status
- 15 April 2022
- Published by Springer Nature in Transactions of the Indian National Academy of Engineering
- Vol. 7 (3) , 851-871
Short and Ultrashort Laser Surface Processing of Alpha + Beta Titanium Alloy (Ti6Al4V): Present Status
- 1 December 2021
- Published by IOP Publishing in Surface Topography: Metrology and Properties
- Vol. 9 (4) , 045039
Wear and corrosion behavior of nano carbide dispersed AISI304 stainless steel by laser surface processing
In this study, dispersion of tungsten carbide on AISI 304 stainless steel substrate has been carried out by laser melting of the sand blasted substrate using a 5 kW continuous wave (CW) Nd:YAG laser (with the beam diameter of 3 mm) with an output power ranging from 1.5–2 kW, and scan speed varying from 12 to 16 mm s −1 and simultaneous feeding of premixed WC + Co powders in the ratio (wt) of 1:4 (with a flow rate of 10 mg s −1 ). The microstructure of the composite zone is dendritic or cellular in morphology and consists of nano-tungsten carbide (both WC and W 2 C) and M 23 C 6 precipitates. There is an enhancement in hardness due to carbide dispersion from 220 VHN of the as-received substrate to 290–400 VHN. The wear resistance is improved significantly with a maximum enhancement observed in the sample processed with an applied power of 2 kW and a scan speed of 12 mm s −1 . The corrosion rate in a 3.56 wt% NaCl solution is significantly reduced due to laser processing in most samples except when processed with 2.5 kW applied power and 12 mm s −1 scan speed. However, pitting corrosion resistance is found to be improved (shifting of E pit towards noble direction) for the sample processed with an applied power of 2 kW and a scan speed of 12 mm s −1 .
- 1 December 2021
- Published by IOP Publishing in Surface Topography: Metrology and Properties
- Vol. 9 (4) , 045039
Wear and corrosion behavior of nano carbide dispersed AISI304 stainless steel by laser surface processing
In this study, dispersion of tungsten carbide on AISI 304 stainless steel substrate has been carried out by laser melting of the sand blasted substrate using a 5 kW continuous wave (CW) Nd:YAG laser (with the beam diameter of 3 mm) with an output power ranging from 1.5–2 kW, and scan speed varying from 12 to 16 mm s −1 and simultaneous feeding of premixed WC + Co powders in the ratio (wt) of 1:4 (with a flow rate of 10 mg s −1 ). The microstructure of the composite zone is dendritic or cellular in morphology and consists of nano-tungsten carbide (both WC and W 2 C) and M 23 C 6 precipitates. There is an enhancement in hardness due to carbide dispersion from 220 VHN of the as-received substrate to 290–400 VHN. The wear resistance is improved significantly with a maximum enhancement observed in the sample processed with an applied power of 2 kW and a scan speed of 12 mm s −1 . The corrosion rate in a 3.56 wt% NaCl solution is significantly reduced due to laser processing in most samples except when processed with 2.5 kW applied power and 12 mm s −1 scan speed. However, pitting corrosion resistance is found to be improved (shifting of E pit towards noble direction) for the sample processed with an applied power of 2 kW and a scan speed of 12 mm s −1 .
- 29 July 2021
- Published by Springer Nature in Transactions of the Indian National Academy of Engineering
- Vol. 6 (4) , 933-953
3-D Printing by Laser-Assisted Direct Energy Deposition (LDED): The Present Status
- 29 July 2021
- Published by Springer Nature in Transactions of the Indian National Academy of Engineering
- Vol. 6 (4) , 933-953
3-D Printing by Laser-Assisted Direct Energy Deposition (LDED): The Present Status