Hairu Wang
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Hairu Wang has a total of 11 co-authors. Here are the top co-authors by number of shared publications:
- Oscar Quevedo-Teruel
KTH Royal Institute of Technology
5 shared publications - Cleofás Segura-Gómez
Department of Signal Theory, Telematics and Communications. Research Centre for Information and Communication Technologies, University of Granada, Granada, Spain
2 shared publications - Francisco Mesa
KTH Royal Institute of Technology
2 shared publications - José Rico-Fernández
Northern Waves AB, Stockholm, Sweden
2 shared publications - Mingzheng Chen
Department of Communication Systems, KTH Royal Institute of Technology, Stockholm, Sweden
2 shared publications - Oskar Zetterstrom
KTH Royal Institute of Technology, Stockholm, Sweden
2 shared publications
Latest Publications
- Open Access
- 28 January 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Antennas and Wireless Propagation Letters
- Vol. 25 (4) , 1537-1541
Monolithic Additively Manufactured Broadband Horn Array Antenna in $W$ BandThis letter presents the design, fabrication, and experimental validation of a fully metallic $4\,\times \,4$ horn array antenna operating in the entire $W$-band ($75-110\,$GHz). The array integrates a broadband $1:16$ beamforming network and 16 pyramidal horn elements into a single monolithic structure. The beamforming network is composed of wideband twisters and E-plane power dividers, which are compatible with the metal-only additive manufacturing (AM) technique called laser powder-bed fusion (LPBF). The simulation and measurement results confirm a reflection coefficient below $-12\,$dB in a 37.8% relative bandwidth, with a measured realized gain exceeding $21\,$dBi across the band. The array achieves an aperture efficiency of approximately 80% (calculated using realized gain) while maintaining sidelobe levels below $-10\,$dB.
- 28 January 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Antennas and Wireless Propagation Letters
- Vol. 25 (4) , 1537-1541
Open AccessMonolithic Additively Manufactured Broadband Horn Array Antenna in $W$ BandThis letter presents the design, fabrication, and experimental validation of a fully metallic $4\,\times \,4$ horn array antenna operating in the entire $W$-band ($75-110\,$GHz). The array integrates a broadband $1:16$ beamforming network and 16 pyramidal horn elements into a single monolithic structure. The beamforming network is composed of wideband twisters and E-plane power dividers, which are compatible with the metal-only additive manufacturing (AM) technique called laser powder-bed fusion (LPBF). The simulation and measurement results confirm a reflection coefficient below $-12\,$dB in a 37.8% relative bandwidth, with a measured realized gain exceeding $21\,$dBi across the band. The array achieves an aperture efficiency of approximately 80% (calculated using realized gain) while maintaining sidelobe levels below $-10\,$dB.
- Open Access
- 1 January 2026
- Published by Institution of Engineering and Technology (IET) in IET Microwaves, Antennas & Propagation
- Vol. 20 (1) , e70134
Hybrid Dielectric–Metadome Structures Modelled via 2‐D Ray Tracing and Physical Optics
This study introduces a hybrid dome structure that combines a dielectric lens (DL) and a metadome (MD) to enhance the scanning capabilities of phased array antennas (PAAs). These configurations show great potential for improving the scanning capacity of PAAs with a lightweight dome while allowing a broad frequency range. Since traditional full‐wave simulations of such electrically large structures are computationally intensive and time‐consuming, the radiation characteristics of hybrid dome structures are analysed using a simplified two‐dimensional (2‐D) ray‐tracing and physical‐optics (RT‐PO) model. This RT‐PO model enables precise computation of the radiation pattern in a principal plane using much less computational resources than full‐wave simulations. The RT‐PO model is validated by comparing it with full‐wave simulations of hybrid domes featuring practical metaelements. The novelty of this work lies in the validation of the hybrid dome concept and the use of a simplified 2‐D RT‐PO model that facilitates rapid analysis/design tasks. The hybrid dome is found to be an effective solution to extend the scanning range of PAAs and this integrated system is highly suitable for a wide range of uses in emerging beam‐scanning antenna technologies.
- 1 January 2026
- Published by Institution of Engineering and Technology (IET) in IET Microwaves, Antennas & Propagation
- Vol. 20 (1) , e70134
Open AccessHybrid Dielectric–Metadome Structures Modelled via 2‐D Ray Tracing and Physical Optics
This study introduces a hybrid dome structure that combines a dielectric lens (DL) and a metadome (MD) to enhance the scanning capabilities of phased array antennas (PAAs). These configurations show great potential for improving the scanning capacity of PAAs with a lightweight dome while allowing a broad frequency range. Since traditional full‐wave simulations of such electrically large structures are computationally intensive and time‐consuming, the radiation characteristics of hybrid dome structures are analysed using a simplified two‐dimensional (2‐D) ray‐tracing and physical‐optics (RT‐PO) model. This RT‐PO model enables precise computation of the radiation pattern in a principal plane using much less computational resources than full‐wave simulations. The RT‐PO model is validated by comparing it with full‐wave simulations of hybrid domes featuring practical metaelements. The novelty of this work lies in the validation of the hybrid dome concept and the use of a simplified 2‐D RT‐PO model that facilitates rapid analysis/design tasks. The hybrid dome is found to be an effective solution to extend the scanning range of PAAs and this integrated system is highly suitable for a wide range of uses in emerging beam‐scanning antenna technologies.
- Open Access
- 20 October 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Terahertz Science and Technology
- Vol. 16 (3) , 296-306
A Sub-THz Low-Cost Additive Manufactured Monolithic Geodesic H-Plane Horn Array Antenna
A monolithic geodesic H-plane horn array antenna that operates up to 170 GHz is achieved for the first time using a low-cost additive manufacturing (AM) technique. To reach high gain and symmetric beam, a truncated geodesic H-plane horn is used to obtain a narrow beam in the H-plane, while a 1:8 power divider built on parallel-plate waveguides is constructed to narrow the beam in the E-plane. A ray-tracing and physical-optics model is developed to facilitate the design, which is capable of computing the full radiation pattern, directivity, and gain (considering conductive losses) of geodesic H-plane horn array antennas with significant time efficiency and high degree of accuracy. The adopted metal-only laser powder–bed fusion AM technique is especially suitable for fast prototyping structures with intricate shapes at a low cost. However, special adaptations are still considered in the design to ensure a successful fabrication of the prototype operating at the D-band. The prototype maintains good frequency stability from 110 to 170 GHz with a return loss better than 10 dB and a symmetric pencil beam. The measured data show a maximum realized gain of 29 dBi, a maximum aperture efficiency of 67% (calculated using realized gain), and a maximum radiation efficiency of 86%.
- 20 October 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Terahertz Science and Technology
- Vol. 16 (3) , 296-306
Open AccessA Sub-THz Low-Cost Additive Manufactured Monolithic Geodesic H-Plane Horn Array Antenna
A monolithic geodesic H-plane horn array antenna that operates up to 170 GHz is achieved for the first time using a low-cost additive manufacturing (AM) technique. To reach high gain and symmetric beam, a truncated geodesic H-plane horn is used to obtain a narrow beam in the H-plane, while a 1:8 power divider built on parallel-plate waveguides is constructed to narrow the beam in the E-plane. A ray-tracing and physical-optics model is developed to facilitate the design, which is capable of computing the full radiation pattern, directivity, and gain (considering conductive losses) of geodesic H-plane horn array antennas with significant time efficiency and high degree of accuracy. The adopted metal-only laser powder–bed fusion AM technique is especially suitable for fast prototyping structures with intricate shapes at a low cost. However, special adaptations are still considered in the design to ensure a successful fabrication of the prototype operating at the D-band. The prototype maintains good frequency stability from 110 to 170 GHz with a return loss better than 10 dB and a symmetric pencil beam. The measured data show a maximum realized gain of 29 dBi, a maximum aperture efficiency of 67% (calculated using realized gain), and a maximum radiation efficiency of 86%.
- Open Access
- 22 April 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of Microwaves
- Vol. 4 (3) , 568-580
Simulation Conditions to Compute the Dispersion Diagram of 3D Periodic Structures
In this work, we examine the methodology for numerically computing the dispersion diagram of three-dimensional periodic structures using commercial electromagnetic simulators. Examples of periodic structures based on body-centered cubic, face-centered cubic, and monoclinic lattices are used to illustrate this methodology. We first outline the characteristics of these structures in both physical and reciprocal spaces from a theoretical point of view. On this basis, we provide a comprehensive explanation of how to adjust the setting in simulation software commonly used in microwave engineering to generate the dispersion diagrams of these structures. The appropriate simulation conditions are tabulated to serve as a further guide for other researchers. This study also explores the influence of the elements of the unit cell on the dispersion characteristics. Additionally, we evaluate and contrast the dispersion properties of identical periodic elements when having simple cubic, body-centered cubic, and face-centered cubic arrangements. We found that symmetries, such as those seen in body-centered cubic and face-centered cubic arrangements, can improve the isotropy and maintain low-dispersion characteristics over a wider frequency range. The monoclinic structure is also taken as an example to demonstrate that the reported analysis method can be applied to the dispersion analysis of other more complex noncubic lattices. Our findings offer useful information for the examination and engineering of three-dimensional periodic structures, which can be used to design microwave and antenna devices.
- 22 April 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of Microwaves
- Vol. 4 (3) , 568-580
Open AccessSimulation Conditions to Compute the Dispersion Diagram of 3D Periodic Structures
In this work, we examine the methodology for numerically computing the dispersion diagram of three-dimensional periodic structures using commercial electromagnetic simulators. Examples of periodic structures based on body-centered cubic, face-centered cubic, and monoclinic lattices are used to illustrate this methodology. We first outline the characteristics of these structures in both physical and reciprocal spaces from a theoretical point of view. On this basis, we provide a comprehensive explanation of how to adjust the setting in simulation software commonly used in microwave engineering to generate the dispersion diagrams of these structures. The appropriate simulation conditions are tabulated to serve as a further guide for other researchers. This study also explores the influence of the elements of the unit cell on the dispersion characteristics. Additionally, we evaluate and contrast the dispersion properties of identical periodic elements when having simple cubic, body-centered cubic, and face-centered cubic arrangements. We found that symmetries, such as those seen in body-centered cubic and face-centered cubic arrangements, can improve the isotropy and maintain low-dispersion characteristics over a wider frequency range. The monoclinic structure is also taken as an example to demonstrate that the reported analysis method can be applied to the dispersion analysis of other more complex noncubic lattices. Our findings offer useful information for the examination and engineering of three-dimensional periodic structures, which can be used to design microwave and antenna devices.
- Open Access
- 3 August 2021
- Published by MDPI AG in Applied Sciences
- Vol. 11 (15) , 7153
Three-Dimensional Broadband and Isotropic Double-Mesh Twin-Wire Media for Meta-Lenses
Lenses are used for multiple applications, including communications, surveillance and security, and medical instruments. In homogeneous lenses, the contour is used to control the electromagnetic propagation. Differently, graded-index lenses make use of inhomogeneous materials, which is an extra degree of freedom. This extra degree of freedom enables the design of devices with a high performance. For instance, rotationally symmetric lenses without spherical aberrations, e.g., the Luneburg lens, can be designed. However, the manufacturing of such lenses is more complex. One possible approach to implement these lenses is using metamaterials, which are able to produce equivalent refractive indices. Here, we propose a new type of three-dimensional metamaterial formed with two independent sets of wires. The double-mesh twin-wire structure permits the propagation of a first mode without cut-off frequency and with low dispersion and high isotropy. These properties are similar to periodic structures with higher symmetries, such as glide symmetry. The variations of the equivalent refractive index are achieved with the dimension of the meandered wires. The potential of this new metamaterial is demonstrated with simulated results of a Luneburg meta-lens.
- 3 August 2021
- Published by MDPI AG in Applied Sciences
- Vol. 11 (15) , 7153
Open AccessThree-Dimensional Broadband and Isotropic Double-Mesh Twin-Wire Media for Meta-Lenses
Lenses are used for multiple applications, including communications, surveillance and security, and medical instruments. In homogeneous lenses, the contour is used to control the electromagnetic propagation. Differently, graded-index lenses make use of inhomogeneous materials, which is an extra degree of freedom. This extra degree of freedom enables the design of devices with a high performance. For instance, rotationally symmetric lenses without spherical aberrations, e.g., the Luneburg lens, can be designed. However, the manufacturing of such lenses is more complex. One possible approach to implement these lenses is using metamaterials, which are able to produce equivalent refractive indices. Here, we propose a new type of three-dimensional metamaterial formed with two independent sets of wires. The double-mesh twin-wire structure permits the propagation of a first mode without cut-off frequency and with low dispersion and high isotropy. These properties are similar to periodic structures with higher symmetries, such as glide symmetry. The variations of the equivalent refractive index are achieved with the dimension of the meandered wires. The potential of this new metamaterial is demonstrated with simulated results of a Luneburg meta-lens.