NTNevine Tagscherer

Nevine Tagscherer

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article


Nevine Tagscherer has a total of 10 co-authors. Here are the top co-authors by number of shared publications:

  • Klaus Drechsler

    Chair of Carbon Composites, Technical University of Munich, Boltzmannstr. 15, 85748 Garching, Germany

    3 shared publications
  • André Marcel Bär

    New Technologies and China, BMW Group, Petuelring 130, 80788 Munich, Germany

    1 shared publication
  • Houyem Latiri

    TUM Department of Mechanical Engineering, Chair of Carbon Composites Technical University of Munich Garching bei München Germany

    1 shared publication
  • Ingo Leonard Kottenstedde

    Research, New Technologies, Innovations BMW Group Munich Germany

    1 shared publication
  • Klaus Drechsler

    TUM Department of Mechanical Engineering, Chair of Carbon Composites Technical University of Munich Garching bei München Germany

    1 shared publication
  • Patrick Consul

    Chair of Carbon Composites, Department of Aerospace and Geodesy, Technical University of Munich, 85748 Garching, Germany

    1 shared publication

Latest Publications

  • Open Access

    Foundational Investigation on the Characterization of Porosity and Fiber Orientation Using XCT in Large-Scale Extrusion Additive Manufacturing

    by Nevine Tagscherer, Thomas Schromm, Klaus Drechsler

    The great potential of Extrusion Additive Manufacturing (EAM) for structural prototyping in the automotive industry is severely limited by the directional bias in the build direction. The layerwise fabrication leads to reduced mechanical properties at the layer-to-layer interface compared to the bulk of the strand. Especially for the often-used semi-crystalline thermoplastics, the mechanical properties strongly depend on the processing parameters, even more so if short fibers are used as fillers. Therefore, ideal processing windows in which the mechanical strength and modulus in the z-direction reach their maximum can be identified for these parameters, resulting in a reduced directional bias. The influence of the EAM processing parameters on mechanical strength has already been investigated, correlating strength with thermal conditions during printing. However, these considerations did not distinguish between the thermal effect on the polymer properties, the formation of voids and pores at the layer interface, and the resulting fiber orientation for different strand proportions. Therefore, in this study, the effect of different processing temperatures and layer heights on the pore size and distribution, as well as the fiber orientation in the different regions of the mesostructure was investigated using X-ray Computed Tomography (XCT).


  • Open Access

    Mechanical Analysis of Parameter Variations in Large-Scale Extrusion Additive Manufacturing of Thermoplastic Composites

    by Nevine Tagscherer, André Marcel Bär, Swen Zaremba, Klaus Drechsler

    Large structural parts manufactured by Extrusion Additive Manufacturing (EAM) are limited by strong anisotropy due to insufficient bond formation and reduced molecular entanglement along the layer interface. To understand the correlation between process and material parameters and to enable digital modeling of EAM, the effect of different substrate temperatures and layer heights on tensile strength was investigated. A simple testing methodology for pelletized carbon fiber-filled polyamide 6 was developed. Tensile tests were performed in a full factorial Design of Experiments (DoE) to determine the tensile properties. For bulk simulation, the nominal strength and modulus were also determined based on contact width obtained by optical microscopy. The results demonstrated high anisotropy, with the maximum transverse tensile strength reaching only 27% of the corresponding longitudinal results and the transverse tensile modulus reaching only 20% of its longitudinal value. The effects of varying layer height were less significant than varying substrate temperature. The results support the hypothesis that sufficient transverse tensile strength is achieved between the extrapolated crystallization onset and melt temperature. The methodology of this study can be used as a benchmark method to qualify new thermoplastic polymers for EAM processes and to determine optimal process parameters for improved fusion bonding.


  • Open Access

    Targeted Temperature Manipulation and Analysis of the Influence on Mechanical Properties in Large-Scale Extrusion Additive Manufacturing

    by Nevine Tagscherer, Tim A. Osswald, Klaus Drechsler

    Layer times in large-scale Extrusion Additive Manufacturing (EAM) of carbon fiber-reinforced thermoplastics are often outside the recommended process window. Brief layer times of tall parts with short path lengths lead to high temperatures and thus to melting of the component. In contrast, the substrate temperature decreases too far at longer layer times to achieve sufficient fusion bonding through molecular diffusion across the interface. Heating by infrared emitters and cooling by compressed air were experimentally tested and evaluated as methods for temperature control. Assuming that bond formation is mainly temperature-controlled, mechanical properties were expected to be similar to those of non-manipulated samples at the same temperatures. Samples of short carbon fiber-filled polyamide 6 in pellet form were manufactured in three test series. Infrared heating resulted in comparable tensile properties to samples at the target temperature and in a significant increase compared to the base temperature without heating. Cooling proved to be more effective when closer to the deposition nozzle, with tensile results even exceeding the expected values at temperatures below 170 °C. Overall, the results support the potential for targeted temperature control in EAM and the hypothesis that comparable bond strength can be achieved in dependence of the final substrate temperature.


  • Open Access

    Investigation of nonisothermal fusion bonding for extrusion additive manufacturing of large structural parts

    by Nevine Tagscherer, Patrick Consul, Ingo Leonard Kottenstedde, Houyem Latiri, Swen Zaremba, Klaus Drechsler

    Fusion bonding is understood to be the decisive mechanism for the interlayer strength in extrusion additive manufacturing. This study links the characteristic temperatures of semicrystalline thermoplastics, namely, PA6 with 40% carbon fibers, to the bond formation in respect to real‐world processing conditions. Based on theoretical investigations, a process window is proposed for bonding to occur without polymer degradation. This range from the glass transition to the initial degradation temperature was determined through differential scanning calorimetry and thermogravimetric analysis. A second process window for optimal bonding is proposed from the extrapolated onset crystallization temperature, , to the melt temperature, . The validation of these process windows was conducted by bending tests according to DIN EN 178. was confirmed as the upper limit, with the part's geometric integrity compromised at higher temperatures. had to be refuted as lower limit as no discrete reduction in bond strength was determined in alignment with . Authors suggest the lower limit is defined by the lowest substrate temperature to lead to interface temperatures above the onset of melt temperature. By utilizing thermal analyses, less time and resources are required to detemine a suitable process window for extrusion additive manufacturing.