JWJack R. J. Wetherell

Jack R. J. Wetherell

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article


Jack R. J. Wetherell has a total of 6 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Open Access

    The unsteadiness of liquid jet breakup in subsonic crossflow

    by Jack R.J. Wetherell, Mark Brend, Andrew Garmory, Dan Sykes, A. Duncan Walker


  • PREDICTION OF AERODYNAMIC FORCES ON A LIQUID JET IN CROSSFLOW

    by Jack R. J. Wetherell, Mark Brend, Andrew Garmory, A. Duncan Walker

    Liquid jet in crossflow (JICF) injectors are a popular method of producing a spray of liquid droplets. Lagrangian based models are an attractive option for simulation of JICF due to their convenience in a wider simulation methodology. To further develop these models, it is desirable to know the aerodynamic forces exerted on the liquid jet. In this paper, we present simulations of a liquid jet injected into a subsonic crossflow at two different momentum flux ratios. A coupled level set and volume of fluid solver with adaptive meshing is used for the simulations. Methods for calculating the instantaneous pressure and viscous forces on the surface of the liquid column are presented, which are used to calculate forces. It is shown that the force on the liquid column is dominated by the pressure drag. The choice of reference area between actual frontal area and a nominal value found from injection diameter and penetration length is found to give significant differences. When using the nominal value, a drag coefficient for the whole column of approximately 4 is found for both cases, in agreement with previous studies based on overall trajectory. The variation of force coefficients along the column show that in the streamwise direction the force initially increases due to the flattening of the jet before decreasing as the jet area reduces. A force in the direction opposite to the jet injection is produced which increases along the jet and becomes particularly significant for the low momentum case considered.

  • Open Access

    Air-Film Coupling in Prefilming Airblast Atomisers and the Implications for Subsequent Atomisation

    by Jack R. J. Wetherell, Andrew Garmory

    Prefilming airblast atomisers are commonly used in gas turbine combustion system fuel injectors. As the film propagates across the prefilmer it interacts with the high velocity gas stream above it. In this paper a numerical investigation into this interaction is presented. A Coupled Level Set & Volume of Fluid method is used to simulate the development of the film along the KIT-ITS planar prefilmer (Gepperth et al., in: 23rd European conference on liquid atomization and spray systems (ILASS-Europe 2010), Brno, Czech Republic, September, 2010). Initial results showed the importance of correctly specifying the contact angle as too high a value leads to the formation of rivulets instead of a continuous film. An analysis of the film and air showed two-way coupling. The presence of the film increases the growth rate of the gas phase boundary layer, and the strength and size of the turbulent structures within it. Surface waves form in the film, initially driven by the turbulent fluctuations, but developing into transverse waves. These waves are shown to be independent, stochastic events instead of a periodic wave system. At the trailing edge of the prefilmer the increased turbulence level in the air, the variations in the film thickness and the associated change in fuel mass flow and momentum will have large implications for the atomisation process and subsequent fuel spray. These will also impact simulation of the atomisation, as the boundary condition complexity is much greater than commonly used, and the variations will require larger domains and longer simulation times to obtain fully converged atomisation statistics.


  • Open Access

    Air-film coupling in prefilming airblast atomisers and the implications for subsequent atomisation

    by Jack R. J. Wetherell, Andrew Garmory

    Prefilming airblast atomisers are commonly used in gas turbine combustion system fuel injectors. As the film propagates across the prefilmer it interacts with the high velocity gas stream above it. In this paper a numerical investigation into this interaction is presented. A Coupled Level Set \& Volume of Fluid method is used to simulate the development of the film along the KIT-ITS planar prefilmer (Gepperth et al., 2010). Initial results showed the importance of correctly specifying the contact angle as too high a value leads to the formation of rivulets instead of a continuous film. An analysis of the film and air showed two-way coupling. The presence of the film increases the growth rate of the gas phase boundary layer, and the strength and size of the turbulent structures within it. Surface waves form in the film, initially driven by the turbulent fluctuations, but developing into transverse waves. These waves are shown to be independent, stochastic events instead of a periodic wave system. At the trailing edge of the prefilmer the increased turbulence level in the air, the variations in the film thickness and the associated change in fuel mass flow and momentum will have large implications for the atomisation process and subsequent fuel spray. These will also impact simulation of the atomisation, as the boundary condition complexity is much greater than commonly used, and the variations will require larger domains and longer simulation times to obtain fully converged atomisation statistics.

  • The Effect of Film Development on Primary Breakup in a Prefilming Airblast Atomizer

    by Jack R. J. Wetherell, Andrew Garmory

    Liquid fueled gas turbines are likely to remain a dominant force in aviation propulsion for the foreseeable future, and therefore understanding the atomization process is key to meeting future emissions and performance legislation. To make experiments and simulations possible, simplified geometry and boundary conditions are often used, for example, simulations of primary atomization often use a fixed film height and velocity. This paper aims to quantify the effect of a fully developed unsteady film on the atomization process. A custom Coupled Level Set & Volume of Fluid (CLSVOF) solver with adaptive meshing built in OpenFOAM v9 is used. A simulation of the atomization process in the Karlsruhe Institute of Technology atomization experiment (Warncke et al., 2017, “Experimental and Numerical Investigation of the Primary Breakup of an Airblasted Liquid Sheet,” Int. J. Multiphase Flow, 91, pp. 208–224) is presented. A precursor simulation of the film development is used to provide accurate, temporally and spatially resolved inlet boundary conditions. These results are compared to previous CLSVOF simulations from Wetherell et al. (2020, “Coupled Level Set Volume of Fluid Simulations of Prefilming Airblast Atomization With Adaptive Meshing,” ASME Paper No. GT2020-14213)” using traditional boundary conditions. The unsteady film has doubled the modal ligament length and widened the distribution, and is now in better agreement with experimental measurements. A clear correlation in both time and space is observed between the film, atomization process, and spray. The sauter mean diameter (SMD) is significantly increased, again giving better agreement with the experiment. A discussion of extracting statistical descriptions of the spray is given, outlining the unfeasible computational cost required to converge droplet diameter distributions and other high order statistics for a case such as this.


  • Open Access

    Coupled Level Set Volume of Fluid Simulations of Prefilming Airblast Atomization With Adaptive Meshing

    by Jack Wetherell, Andrew Garmory, Maciej Skarysz

    The fuel atomisation process and the resultant spray drive nearly all aspects of gas turbine combustion system performance, including emissions. A greater understanding of the fuel atomisation process is therefore required if future requirements are to be met. The majority of investigations into fuel atomisation mechanisms and performance to date have been performed at atmospheric