Donghan Lee
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Donghan Lee has a total of 8 co-authors. Here are the top co-authors by number of shared publications:
- Jaehoon Kim
Department of Electrical and Information Engineering, Seoul National University of Science and Technology, Seoul, South Korea
3 shared publications - Sewan Choi
Department of Electrical and Information Engineering, Seoul National University of Science and Technology, Seoul, South Korea
3 shared publications - Huu-Phuc Kieu
Department of Electrical and Information Engineering, Seoul National University of Science and Technology (Seoul Tech), Seoul, South Korea
2 shared publications - Chaeyoung Suk
Department of Converter Development Project, LG Magna, Incheon, South Korea
1 shared publication - Gibum Yu
Bradley Department of Electrical and Computer Engineering, Center for Power Electronics Systems (CPES), Virginia Polytechnic and State University, Blacksburg, VA, USA
1 shared publication - Sangjin Kim
Department of Electric Power Conversion Engineering Design, Hyundai Motor Company, Hwaseong, South Korea
1 shared publication
Latest Publications
- 27 November 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Industrial Electronics
- Vol. 72 (6) , 6027-6037
Single/Three-Phase Compatible Sigma-Type OBC With Reduced Electrolytic Capacitor Volume
This article proposes a sigma-type dc–dc converter with a reduced energy volume of the electrolytic capacitor (E-cap) for single- and three-phase compatible on-board charger (OBC). The proposed relay box configuration uses a minimal number of relays. In single-phase grid, the E-cap is connected to the dc-link via the input-parallel output-series (IPOS) structure to absorb second harmonic current. In a three-phase grid, a film capacitor connects to the dc-link instead of E-cap, maintaining the low voltage rating of the E-cap by the input-independent output-series (IIOS) structure. Additionally, the power of the regulated converter is reduced, allowing most of the power to flow through the unregulated converter, achieving high efficiency. The proposed sigma converter achieves soft-switching under a wide voltage range and reduces the power burden of the regulated converter through a reconfigurable leg. Experimental results from an 11 kW prototype validate the proposed circuit. The converter achieved a peak efficiency of 98.12% and maintained high efficiency under a wide voltage range.
- 27 November 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Industrial Electronics
- Vol. 72 (6) , 6027-6037
Single/Three-Phase Compatible Sigma-Type OBC With Reduced Electrolytic Capacitor Volume
This article proposes a sigma-type dc–dc converter with a reduced energy volume of the electrolytic capacitor (E-cap) for single- and three-phase compatible on-board charger (OBC). The proposed relay box configuration uses a minimal number of relays. In single-phase grid, the E-cap is connected to the dc-link via the input-parallel output-series (IPOS) structure to absorb second harmonic current. In a three-phase grid, a film capacitor connects to the dc-link instead of E-cap, maintaining the low voltage rating of the E-cap by the input-independent output-series (IIOS) structure. Additionally, the power of the regulated converter is reduced, allowing most of the power to flow through the unregulated converter, achieving high efficiency. The proposed sigma converter achieves soft-switching under a wide voltage range and reduces the power burden of the regulated converter through a reconfigurable leg. Experimental results from an 11 kW prototype validate the proposed circuit. The converter achieved a peak efficiency of 98.12% and maintained high efficiency under a wide voltage range.
- 22 May 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Industrial Electronics
- Vol. 71 (12) , 15815-15825
A GaN-Based Improved Zeta Converter With Integrated Planar Transformer for 800-V Electric Vehicles
This article proposes a high-step-down dc-dc converter for electric vehicles with an 800 V battery system. The proposed converter significantly reduces the current rating requirement for the dc blocking capacitor on the secondary side by reconstructing the secondary side circuit. The maximum duty cycle of the proposed converter is larger than the phase-shift full-bridge converter, which allows the use of larger leakage inductance. This turns out to be a crucial advantage to achieve the wide range zero voltage switching (ZVS) in high switching frequencies over 500 kHz. In addition, with a three-level structure, the voltage rating of the primary side switch is determined as half the input voltage and the energy to achieve ZVS turn-on is reduced, so it is suitable for high-frequency operation using a gallium nitride (GaN) device. The two transformers are integrated with partial flux cancelation, resulting in 10.3% of power loss and 27.7% of footprint reduction. Finally, a 700 kHz GaN-based 1.2 kW prototype achieved a power density of 10.2 kW/L and a peak efficiency of 93.4%.
- 22 May 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Industrial Electronics
- Vol. 71 (12) , 15815-15825
A GaN-Based Improved Zeta Converter With Integrated Planar Transformer for 800-V Electric Vehicles
This article proposes a high-step-down dc-dc converter for electric vehicles with an 800 V battery system. The proposed converter significantly reduces the current rating requirement for the dc blocking capacitor on the secondary side by reconstructing the secondary side circuit. The maximum duty cycle of the proposed converter is larger than the phase-shift full-bridge converter, which allows the use of larger leakage inductance. This turns out to be a crucial advantage to achieve the wide range zero voltage switching (ZVS) in high switching frequencies over 500 kHz. In addition, with a three-level structure, the voltage rating of the primary side switch is determined as half the input voltage and the energy to achieve ZVS turn-on is reduced, so it is suitable for high-frequency operation using a gallium nitride (GaN) device. The two transformers are integrated with partial flux cancelation, resulting in 10.3% of power loss and 27.7% of footprint reduction. Finally, a 700 kHz GaN-based 1.2 kW prototype achieved a power density of 10.2 kW/L and a peak efficiency of 93.4%.
- 14 July 2021
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Power Electronics
- Vol. 37 (1) , 617-628
Modular Bidirectional Differential Converter With Series Parallel Connected Output for Ultra-Wide-Voltage Applications: Control, Module Shedding, and Fail-Safe Operation
In this paper, a modular output series-parallel SRC-differential buck converter is analyzed for high-power, ultra-wide-voltage applications such as battery formation systems and bench-type power supplies where a zero voltage discharging function is required. An independent control method in one module is proposed to increase the efficiency of the converter compared to the conventional complementary control method. In the modular output-series connection, higher efficiency can be achieved by shedding needless modules in the low voltage range. Module shedding and activating techniques are proposed to eliminate current and voltage transients during a mode change under any load condition without the use of additional bypass switches. In addition, when a fault occurs in one module, its effect on the other module is analyzed. A practical solution involving turn-off processes for fail-safe operation is proposed, which reduces current stress and voltage spikes on devices and effect among modules without depending on the external signal from the central controller and the communication delay. A modular 30kW series-parallel SRC- differential buck converter is implemented to verify the proposed concept.
- 14 July 2021
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Power Electronics
- Vol. 37 (1) , 617-628
Modular Bidirectional Differential Converter With Series Parallel Connected Output for Ultra-Wide-Voltage Applications: Control, Module Shedding, and Fail-Safe Operation
In this paper, a modular output series-parallel SRC-differential buck converter is analyzed for high-power, ultra-wide-voltage applications such as battery formation systems and bench-type power supplies where a zero voltage discharging function is required. An independent control method in one module is proposed to increase the efficiency of the converter compared to the conventional complementary control method. In the modular output-series connection, higher efficiency can be achieved by shedding needless modules in the low voltage range. Module shedding and activating techniques are proposed to eliminate current and voltage transients during a mode change under any load condition without the use of additional bypass switches. In addition, when a fault occurs in one module, its effect on the other module is analyzed. A practical solution involving turn-off processes for fail-safe operation is proposed, which reduces current stress and voltage spikes on devices and effect among modules without depending on the external signal from the central controller and the communication delay. A modular 30kW series-parallel SRC- differential buck converter is implemented to verify the proposed concept.