Huu-Phuc Kieu
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Huu-Phuc Kieu has a total of 19 co-authors. Here are the top co-authors by number of shared publications:
- Sewan Choi
Department of Electrical and Information Engineering, Seoul National University of Science and Technology, Seoul, South Korea
10 shared publications - Ba Phu Do
Department of Electrical and Information Engineering, Seoul National University of Science and Technology, Seoul, South Korea
4 shared publications - Dinh Bao-Hung Nguyen
Department of Electrical and Information Engineering, Seoul National University of Science and Technology (Seoul Tech), Seoul, South Korea
4 shared publications - Million Gerado Geda
Department of Electrical and Information Engineering, Seoul National University of Science and Technology (Seoul Tech), Seoul, South Korea
3 shared publications - Donghan Lee
Department of New and Renewable Energy Convergence, Seoul National University of Science and Technology, Seoul, South Korea
2 shared publications - Jaehoon Kim
Department of Electrical and Information Engineering, Seoul National University of Science and Technology, Seoul, South Korea
2 shared publications
Latest Publications
- 27 March 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Transportation Electrification
- Vol. PP (4) , 1
An improved transformer-grid inductor magnetic integration for single-stage on-board charger
This article proposes an improved integrated magnetic structure for the single-stage interleaved totem-pole AC-DC converter, which is applicable for on-board chargers (OBCs). The grid inductors are integrated into the high-frequency transformer, which eliminates the core and winding of grid inductors. This results in a reduction in the magnetic loss, core material volume, and total volume. The analytical comparison among three core candidates to implement the integrated magnetic structure is discussed. The four-leg integrated magnetic, whose total volume is 11% smaller than that of the prior art integration, is selected for further design. An optimized design based on the Figure of Merit (FoM) method is carried out to design the proposed magnetic. A single-phase 3.7kW single-stage OBC prototype with both discrete and integrated magnetic structures is assembled and tested. Compared to the discrete structure, the converter efficiency with the integrated one is 1% higher at light load, and 0.1% higher at full load. In addition, the integrated magnetic volume is 35% smaller than the discrete one. The designed module achieves 97.3% peak efficiency.
- 27 March 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Transportation Electrification
- Vol. PP (4) , 1
An improved transformer-grid inductor magnetic integration for single-stage on-board charger
This article proposes an improved integrated magnetic structure for the single-stage interleaved totem-pole AC-DC converter, which is applicable for on-board chargers (OBCs). The grid inductors are integrated into the high-frequency transformer, which eliminates the core and winding of grid inductors. This results in a reduction in the magnetic loss, core material volume, and total volume. The analytical comparison among three core candidates to implement the integrated magnetic structure is discussed. The four-leg integrated magnetic, whose total volume is 11% smaller than that of the prior art integration, is selected for further design. An optimized design based on the Figure of Merit (FoM) method is carried out to design the proposed magnetic. A single-phase 3.7kW single-stage OBC prototype with both discrete and integrated magnetic structures is assembled and tested. Compared to the discrete structure, the converter efficiency with the integrated one is 1% higher at light load, and 0.1% higher at full load. In addition, the integrated magnetic volume is 35% smaller than the discrete one. The designed module achieves 97.3% peak efficiency.
- 1 October 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of Emerging and Selected Topics in Power Electronics
- Vol. 13 (6) , 8051-8061
A Half-Bridge Single-Stage AC–DC Converter With Single- and Three-Phase Compatibility
This paper presents a single-stage AC–DC converter based on a dual-active half-bridge topology, supporting both single-phase and three-phase operation. The proposed architecture employs three interleaved totem-pole legs on the AC side and three half-bridge legs with split capacitors on the DC side, reducing the switch count compared to the previous full-bridge approach. The converter achieves full zero-voltage switching (ZVS) for all switches in continuous conduction mode (CCM) and zero-current switching (ZCS) for DC-side switches in discontinuous conduction mode (DCM). For single-phase operation, an integrated split-capacitor-type active power decoupling circuit eliminates the second-harmonic ripple in the DC charging current without additional components. To validate the concept, an 11-kW laboratory prototype was developed and tested under both single-phase (220 Vac) and three-phase (380 Vac) inputs, with battery voltages ranging from 400 Vdc to 800 Vdc. Experimental results show peak efficiencies of 96.85%, Experimental results demonstrate a peak efficiency of 96.85%, grid current total harmonic distortion (THD) below 3%, and a power density of 2.7 kW/L.
- 1 October 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of Emerging and Selected Topics in Power Electronics
- Vol. 13 (6) , 8051-8061
A Half-Bridge Single-Stage AC–DC Converter With Single- and Three-Phase Compatibility
This paper presents a single-stage AC–DC converter based on a dual-active half-bridge topology, supporting both single-phase and three-phase operation. The proposed architecture employs three interleaved totem-pole legs on the AC side and three half-bridge legs with split capacitors on the DC side, reducing the switch count compared to the previous full-bridge approach. The converter achieves full zero-voltage switching (ZVS) for all switches in continuous conduction mode (CCM) and zero-current switching (ZCS) for DC-side switches in discontinuous conduction mode (DCM). For single-phase operation, an integrated split-capacitor-type active power decoupling circuit eliminates the second-harmonic ripple in the DC charging current without additional components. To validate the concept, an 11-kW laboratory prototype was developed and tested under both single-phase (220 Vac) and three-phase (380 Vac) inputs, with battery voltages ranging from 400 Vdc to 800 Vdc. Experimental results show peak efficiencies of 96.85%, Experimental results demonstrate a peak efficiency of 96.85%, grid current total harmonic distortion (THD) below 3%, and a power density of 2.7 kW/L.
- 19 August 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Power Electronics
- Vol. 41 (1) , 561-573
Three/Single-Phase Compatibility Single-Stage EV Charger With Six-Switch Full-Bridge Configuration
This article presents a single-stage electrolytic capacitor-less ac–dc converter designed for electric vehicle (EV) chargers, featuring a six-switch full-bridge dc side configuration with both three-phase and single-phase compatibility. The proposed topology features three interleaved totem pole modules on the ac side and a six-switch full bridge on the dc side, interconnected via a delta (Δ) transformer configuration. For three-phase grid operation, this article introduces an advanced duty cycle modulation technique to extend the zero voltage switching (ZVS) range across a wide battery voltage range and enhance the total harmonic distortion (THD) performance of the grid current under varying load conditions. An unbalanced control method is proposed to mitigate low-frequency harmonic distortion in the charging current, effectively compensating for both sag and swell conditions in the grid voltage. The integrated buck-type power decoupling circuit is introduced for single-phase grid operation to absorb the second harmonic current component and eliminate the need for external components. To validate the proposed topology, an 11 kW laboratory EV charger prototype was developed and tested, achieving a peak efficiency of 96.8% and a THD of grid current of 2.5%.
- 19 August 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Power Electronics
- Vol. 41 (1) , 561-573
Three/Single-Phase Compatibility Single-Stage EV Charger With Six-Switch Full-Bridge Configuration
This article presents a single-stage electrolytic capacitor-less ac–dc converter designed for electric vehicle (EV) chargers, featuring a six-switch full-bridge dc side configuration with both three-phase and single-phase compatibility. The proposed topology features three interleaved totem pole modules on the ac side and a six-switch full bridge on the dc side, interconnected via a delta (Δ) transformer configuration. For three-phase grid operation, this article introduces an advanced duty cycle modulation technique to extend the zero voltage switching (ZVS) range across a wide battery voltage range and enhance the total harmonic distortion (THD) performance of the grid current under varying load conditions. An unbalanced control method is proposed to mitigate low-frequency harmonic distortion in the charging current, effectively compensating for both sag and swell conditions in the grid voltage. The integrated buck-type power decoupling circuit is introduced for single-phase grid operation to absorb the second harmonic current component and eliminate the need for external components. To validate the proposed topology, an 11 kW laboratory EV charger prototype was developed and tested, achieving a peak efficiency of 96.8% and a THD of grid current of 2.5%.
- 16 June 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Power Electronics
- Vol. 40 (10) , 14210-14221
New Dual Active Bridge-Series Resonant Converter With Switching and Conduction Loss Reduction for HV-LV Converter in EV Application
In this article, a new HV-LV converter for electric vehicle applications is proposed. The topology combines a dual active bridge-series resonant converter (DAB-SRC) with an interleaved buck/ boost converter. An additional phase-shift control on the LV side is introduced, allowing the active switches to operate near-DCX, resulting in a significant reduction in switching loss. Furthermore, the circulating current is reduced by half compared to conventional [S. Inoue et al. 2017] when operating with a wide voltage range, leading to a reduction in conduction loss. As a result, the switching frequency is doubled compared to existing topology, improving power density by 20.7%. The effectiveness of the proposed topology is verified through experiments on a 6.1 kW prototype, with an LV-side voltage of 48 V/4 kW and 9–16 V/2.1 kW, an HV-side voltage of 400–840 V, and a switching frequency of 200 kHz. A peak efficiency of 96.44% and a power density of 7.5 kW/L were achieved.
- 16 June 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Power Electronics
- Vol. 40 (10) , 14210-14221
New Dual Active Bridge-Series Resonant Converter With Switching and Conduction Loss Reduction for HV-LV Converter in EV Application
In this article, a new HV-LV converter for electric vehicle applications is proposed. The topology combines a dual active bridge-series resonant converter (DAB-SRC) with an interleaved buck/ boost converter. An additional phase-shift control on the LV side is introduced, allowing the active switches to operate near-DCX, resulting in a significant reduction in switching loss. Furthermore, the circulating current is reduced by half compared to conventional [S. Inoue et al. 2017] when operating with a wide voltage range, leading to a reduction in conduction loss. As a result, the switching frequency is doubled compared to existing topology, improving power density by 20.7%. The effectiveness of the proposed topology is verified through experiments on a 6.1 kW prototype, with an LV-side voltage of 48 V/4 kW and 9–16 V/2.1 kW, an HV-side voltage of 400–840 V, and a switching frequency of 200 kHz. A peak efficiency of 96.44% and a power density of 7.5 kW/L were achieved.
- 23 December 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of Emerging and Selected Topics in Power Electronics
- Vol. 13 (2) , 1958-1968
Improved Light-Load Efficiency Modulation for Wide Voltage Range Single-Stage AC–DC Converter
This paper introduces a light load efficient modulation strategy for single-stage AC-DC converters. The proposed modulation scheme is implemented on a modified push-pull single-stage AC-DC converter. This converter achieves a ZVS turn-on over a wide voltage range at full power with the introduced auxiliary inductor. However, single-stage converters commonly suffer from low efficiency at light loads due to hard switching and the dominance of circulating current, which causes significant power losses. To address these challenges, this work proposes a modulation strategy that uses adaptive switching frequency to improve light load efficiency. Experimental results from a 3.7 kW single-stage On-Board Charger (OBC) prototype are provided to verify the theoretical claims across various load levels. As a result, light load conversion performance including efficiency and power quality are improved. This concept is particularly important for Battery Energy Storage Systems (BESS) and photovoltaic (PV) conversion systems, where diversified load levels are common.
- 23 December 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of Emerging and Selected Topics in Power Electronics
- Vol. 13 (2) , 1958-1968
Improved Light-Load Efficiency Modulation for Wide Voltage Range Single-Stage AC–DC Converter
This paper introduces a light load efficient modulation strategy for single-stage AC-DC converters. The proposed modulation scheme is implemented on a modified push-pull single-stage AC-DC converter. This converter achieves a ZVS turn-on over a wide voltage range at full power with the introduced auxiliary inductor. However, single-stage converters commonly suffer from low efficiency at light loads due to hard switching and the dominance of circulating current, which causes significant power losses. To address these challenges, this work proposes a modulation strategy that uses adaptive switching frequency to improve light load efficiency. Experimental results from a 3.7 kW single-stage On-Board Charger (OBC) prototype are provided to verify the theoretical claims across various load levels. As a result, light load conversion performance including efficiency and power quality are improved. This concept is particularly important for Battery Energy Storage Systems (BESS) and photovoltaic (PV) conversion systems, where diversified load levels are common.
- 28 November 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Power Electronics
- Vol. 40 (3) , 4268-4278
Dual Floating Based Three Port DC-DC Converter for EV-APM
This article proposes a new isolated three-port DC-DC converter (TPC) named dual floating dual active bridge (DAB) three-port converter. The proposed converter combines an isolated DAB converter and an interleaved non-isolated dual floating boost (DFB) converter. As the power demand of auxiliary loads in the vehicles rapidly increases due to autonomous and entertainment systems, a dual auxiliary voltage (48V and 12V) system is introduced to mitigate the burden of high current. The high voltage gain feature of the DFB converter ensures that the operating duty remains around 0.5, reducing filter size, turn-off current, and circulating current, and increasing the power transfer capability from the high voltage side. Additionally, the lower voltage stress on the low-side switches allows for the use of switches with lower RDS,on, reducing conduction losses. To validate the theoretical claims, a 6.1kW, 100kHz prototype of the proposed TPC has been built. The prototype operates with a wide HV-port voltage range of 400V-840V and a 12V-port voltage range of 9V-16V while providing a fixed 48V to the 48V-port. The prototype achieves a power density of 9.14kW/L and a peak efficiency of 96.6%.
- 28 November 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Power Electronics
- Vol. 40 (3) , 4268-4278
Dual Floating Based Three Port DC-DC Converter for EV-APM
This article proposes a new isolated three-port DC-DC converter (TPC) named dual floating dual active bridge (DAB) three-port converter. The proposed converter combines an isolated DAB converter and an interleaved non-isolated dual floating boost (DFB) converter. As the power demand of auxiliary loads in the vehicles rapidly increases due to autonomous and entertainment systems, a dual auxiliary voltage (48V and 12V) system is introduced to mitigate the burden of high current. The high voltage gain feature of the DFB converter ensures that the operating duty remains around 0.5, reducing filter size, turn-off current, and circulating current, and increasing the power transfer capability from the high voltage side. Additionally, the lower voltage stress on the low-side switches allows for the use of switches with lower RDS,on, reducing conduction losses. To validate the theoretical claims, a 6.1kW, 100kHz prototype of the proposed TPC has been built. The prototype operates with a wide HV-port voltage range of 400V-840V and a 12V-port voltage range of 9V-16V while providing a fixed 48V to the 48V-port. The prototype achieves a power density of 9.14kW/L and a peak efficiency of 96.6%.
- 11 June 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Power Electronics
- Vol. 39 (10) , 13336-13347
An All-in-One Magnetic Structure for Entire ZVS Range Auxiliary Power Module in Electrical Vehicles
This article proposes an all-in-one magnetic structure that integrates a leakage inductor, two filter inductors, and a transformer in the phase shift full bridge (PSFB) current doubler converter for the auxiliary power module (APM). The proposed integration technique significantly reduces the number of magnetic components, not only achieving a 17.5% reduction in the magnetic volume and a 26% reduction in the magnetic loss but also simplifying the manufacturing processes. Considering the coupling effect in the proposed integrated structure, the zero voltage switching (ZVS) energy is increased. An optimized coupling coefficient is proposed to cover the entire ZVS range, considering the increase in RMS current associated with an elevated coupling coefficient. To validate the effectiveness of the proposed structure, a 3-kW and 200-kHz prototype APM with an input range of 360–800 V and an output voltage range of 11.5–15.3 V is built and tested. The achieved peak efficiency is 95.5%, and the power density reaches 8.4 kW/L.
- 11 June 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Power Electronics
- Vol. 39 (10) , 13336-13347
An All-in-One Magnetic Structure for Entire ZVS Range Auxiliary Power Module in Electrical Vehicles
This article proposes an all-in-one magnetic structure that integrates a leakage inductor, two filter inductors, and a transformer in the phase shift full bridge (PSFB) current doubler converter for the auxiliary power module (APM). The proposed integration technique significantly reduces the number of magnetic components, not only achieving a 17.5% reduction in the magnetic volume and a 26% reduction in the magnetic loss but also simplifying the manufacturing processes. Considering the coupling effect in the proposed integrated structure, the zero voltage switching (ZVS) energy is increased. An optimized coupling coefficient is proposed to cover the entire ZVS range, considering the increase in RMS current associated with an elevated coupling coefficient. To validate the effectiveness of the proposed structure, a 3-kW and 200-kHz prototype APM with an input range of 360–800 V and an output voltage range of 11.5–15.3 V is built and tested. The achieved peak efficiency is 95.5%, and the power density reaches 8.4 kW/L.
- 22 May 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Industrial Electronics
- Vol. 71 (12) , 15815-15825
A GaN-Based Improved Zeta Converter With Integrated Planar Transformer for 800-V Electric Vehicles
This article proposes a high-step-down dc-dc converter for electric vehicles with an 800 V battery system. The proposed converter significantly reduces the current rating requirement for the dc blocking capacitor on the secondary side by reconstructing the secondary side circuit. The maximum duty cycle of the proposed converter is larger than the phase-shift full-bridge converter, which allows the use of larger leakage inductance. This turns out to be a crucial advantage to achieve the wide range zero voltage switching (ZVS) in high switching frequencies over 500 kHz. In addition, with a three-level structure, the voltage rating of the primary side switch is determined as half the input voltage and the energy to achieve ZVS turn-on is reduced, so it is suitable for high-frequency operation using a gallium nitride (GaN) device. The two transformers are integrated with partial flux cancelation, resulting in 10.3% of power loss and 27.7% of footprint reduction. Finally, a 700 kHz GaN-based 1.2 kW prototype achieved a power density of 10.2 kW/L and a peak efficiency of 93.4%.
- 22 May 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Industrial Electronics
- Vol. 71 (12) , 15815-15825
A GaN-Based Improved Zeta Converter With Integrated Planar Transformer for 800-V Electric Vehicles
This article proposes a high-step-down dc-dc converter for electric vehicles with an 800 V battery system. The proposed converter significantly reduces the current rating requirement for the dc blocking capacitor on the secondary side by reconstructing the secondary side circuit. The maximum duty cycle of the proposed converter is larger than the phase-shift full-bridge converter, which allows the use of larger leakage inductance. This turns out to be a crucial advantage to achieve the wide range zero voltage switching (ZVS) in high switching frequencies over 500 kHz. In addition, with a three-level structure, the voltage rating of the primary side switch is determined as half the input voltage and the energy to achieve ZVS turn-on is reduced, so it is suitable for high-frequency operation using a gallium nitride (GaN) device. The two transformers are integrated with partial flux cancelation, resulting in 10.3% of power loss and 27.7% of footprint reduction. Finally, a 700 kHz GaN-based 1.2 kW prototype achieved a power density of 10.2 kW/L and a peak efficiency of 93.4%.
- 23 September 2022
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Power Electronics
- Vol. 38 (2) , 2115-2126
Compact Integrated Transformer – Grid Inductor Structure for E-Capless Single-Stage EV Charger
This article proposes a planar magnetic integration technique that combines the grid inductors and transformer in the single-stage E-capless electric vehicle charger into one core. The proposed integration technique reduces the number of magnetic components; therefore, the cost, total magnetic core loss, and volume can be significantly reduced. Using the integrated structure, the overall converter power density increases up to 11.1% compared to the nonintegrated one. This article also presents a detailed analysis of the optimal printed circuit board (PCB) winding arrangement considering both ac resistance and winding stray capacitance. Due to the high dc resistance of PCB winding, Litz wire was also considered for the proposed integrated structure. The effectiveness of the proposed structure was validated by implementing it on a 3.7-kW prototype of a single-stage ac–dc converter. Results show that the prototype with the proposed integrated structure achieved higher efficiency with both PCB winding and Litz wire. Peak efficiency of 97.17% and 6.55-kW/L power density were achieved.
- 23 September 2022
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Power Electronics
- Vol. 38 (2) , 2115-2126
Compact Integrated Transformer – Grid Inductor Structure for E-Capless Single-Stage EV Charger
This article proposes a planar magnetic integration technique that combines the grid inductors and transformer in the single-stage E-capless electric vehicle charger into one core. The proposed integration technique reduces the number of magnetic components; therefore, the cost, total magnetic core loss, and volume can be significantly reduced. Using the integrated structure, the overall converter power density increases up to 11.1% compared to the nonintegrated one. This article also presents a detailed analysis of the optimal printed circuit board (PCB) winding arrangement considering both ac resistance and winding stray capacitance. Due to the high dc resistance of PCB winding, Litz wire was also considered for the proposed integrated structure. The effectiveness of the proposed structure was validated by implementing it on a 3.7-kW prototype of a single-stage ac–dc converter. Results show that the prototype with the proposed integrated structure achieved higher efficiency with both PCB winding and Litz wire. Peak efficiency of 97.17% and 6.55-kW/L power density were achieved.
- 14 July 2021
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Power Electronics
- Vol. 37 (1) , 617-628
Modular Bidirectional Differential Converter With Series Parallel Connected Output for Ultra-Wide-Voltage Applications: Control, Module Shedding, and Fail-Safe Operation
In this paper, a modular output series-parallel SRC-differential buck converter is analyzed for high-power, ultra-wide-voltage applications such as battery formation systems and bench-type power supplies where a zero voltage discharging function is required. An independent control method in one module is proposed to increase the efficiency of the converter compared to the conventional complementary control method. In the modular output-series connection, higher efficiency can be achieved by shedding needless modules in the low voltage range. Module shedding and activating techniques are proposed to eliminate current and voltage transients during a mode change under any load condition without the use of additional bypass switches. In addition, when a fault occurs in one module, its effect on the other module is analyzed. A practical solution involving turn-off processes for fail-safe operation is proposed, which reduces current stress and voltage spikes on devices and effect among modules without depending on the external signal from the central controller and the communication delay. A modular 30kW series-parallel SRC- differential buck converter is implemented to verify the proposed concept.
- 14 July 2021
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Power Electronics
- Vol. 37 (1) , 617-628
Modular Bidirectional Differential Converter With Series Parallel Connected Output for Ultra-Wide-Voltage Applications: Control, Module Shedding, and Fail-Safe Operation
In this paper, a modular output series-parallel SRC-differential buck converter is analyzed for high-power, ultra-wide-voltage applications such as battery formation systems and bench-type power supplies where a zero voltage discharging function is required. An independent control method in one module is proposed to increase the efficiency of the converter compared to the conventional complementary control method. In the modular output-series connection, higher efficiency can be achieved by shedding needless modules in the low voltage range. Module shedding and activating techniques are proposed to eliminate current and voltage transients during a mode change under any load condition without the use of additional bypass switches. In addition, when a fault occurs in one module, its effect on the other module is analyzed. A practical solution involving turn-off processes for fail-safe operation is proposed, which reduces current stress and voltage spikes on devices and effect among modules without depending on the external signal from the central controller and the communication delay. A modular 30kW series-parallel SRC- differential buck converter is implemented to verify the proposed concept.