WSWasrin Syafii

Wasrin Syafii

*This is an algorithmically generated author record based on publicly available information.

Wasrin Syafii has a total of 31 co-authors. Here are the top co-authors by number of shared publications:

  • Widya Fatriasari

    Research Center for Biomass and Bioproducts, Research Organization for Nanotechnology and Material, National Research and Innovation Agency (BRIN), Serpong 15314, Indonesia

    2 shared publications
  • Adi Santoso

    Research Center for Biomass and Bioproducts, National Research and Innovation Agency, Cibinong, Indonesia

    1 shared publication
  • Ainun Zalsabila

    Department of Forest Products Faculty of Forestry and Environment IPB University 16680 Bogor Indonesia

    1 shared publication
  • Akhiruddin Maddu

    Department of Physics, Faculty of Mathematics and Natural Sciences, IPB University

    1 shared publication
  • Danu

    Forest Tree Seed Technology Research and Development Institute, Bogor 16001, Indonesia

    1 shared publication
  • Deded Sarip Nawawi

    Research Center for Biomass and Bioproducts, National Research and Innovation Agency (BRIN), Jl Raya Bogor KM 46, Cibinong, 16911, Indonesia

    1 shared publication

Latest Publications

  • Open Access

    Deashing of Agricultural Residues and Its Impact on Isolated Lignin Properties: A Mini Review

    by Eko Budi Santoso, Nur Izyan Wan Azelee, Deded Sarip Nawawi, Wasrin Syafii, Widya Fatriasari

    The significant amount of ash content in agricultural biomass presents an enormous challenge for efficient conversion processes. In addressing this issue, various deashing treatments have been tested and established, including simple leaching techniques, which can either be performed with or without the addition of chemical agents. These techniques hold promise for improving the deashing efficiency while potentially altering the structural and chemical composition of biomass, specifically lignin content, which is the key focus of this review. This review starts by exploring the presence of ash in agricultural residues and its impact on biomass properties. Next, this review examines deashing strategies aimed at reducing ash levels in biomass followed by analysis of the resulting changes in lignin physical and chemical properties as well as its thermal characteristics. The final part of this review is concluded by the discussion on the limitations of current approaches and the possible future directions to address the challenges covering the environmental impacts of the deashing treatments. A green process approach is emphasized as a sustainable solution with the aim to minimize negative environmental impacts associated with chemical usage during deashing. Finally, this review highlights the potential for ash recovery as a byproduct of the deashing processes, paving the way for an integrative, closed-loop approach within the biorefinery concept.


  • Mechanically Strong and Fast‐Curing Kraft Lignin‐Based Polyurethane Foam

    by Naurotul Husna, Maya Ismayati, Wasrin Syafii, Widya Fatriasari, Nissa Nurfajrin Solihat

    The creation of biobased rigid polyurethane from nonfood resources such as lignin has garnered significant interest, especially concerning the biorefinery concept. However, few studies have investigated virgin lignin as a polyol source for polyurethane foam and the effects of single factors, such as the lignin solvent, lignin concentration, and lignin:isocyanate ratio, on the properties of polyurethane. High‐density rigid foam (~500 kg/m3) was successfully formed by all the solvents except sodium hydroxide, which was confirmed via Fourier transform infrared (FTIR) spectroscopy and pyrolysis‐gas chromatography–mass spectrometry (Py‐GCMS). The highest to lowest modulus of elasticity (MOE) and modulus of rupture (MOR) values for the different lignin solvents were as follows: tetrahydrofuran (THF) (402.25 and 13.24 N/mm2) > dimethyl formamide (DMF) (46 and 1.69 N/mm2) > dimethyl sulfoxide (DMSO) (29 and 1.39 N/mm2). DMSO was selected as the optimal solvent because of the considerable curing time (26.67 s) needed to produce rigid foam. A higher lignin concentration resulted in better physical, mechanical, and thermal properties of the foam to some extent. Moreover, the opposite occurred with increasing isocyanate ratio in the system. These findings can serve as a basis for optimizing the utilization of lignin as a bioresource in the manufacture of rigid polyurethane foam with more specific uses.

  • Open Access

    Anti-termite Activity of Tamanu Bark Extract (Calophyllum inophyllum L.)

    by Ainun Zalsabila, Wasrin Syafii, Trisna Priadi, Syahidah

    The Journal of the Korean Wood Science and Technology (JKWST) launched in 1973 as an official publication of the Korean Society of Wood Science and Technology has been served as a core of knowledges on wood science and technology.


  • Open Access

    Utilization of Lignocellulosic Waste as a Source of Liquid Smoke: A Literature Review, Lampung, Indonesia

    by Santiyo Wibowo, Wasrin Syafii, Gustan Pari, Elis Nina Herliyana

    Introduction: Lignocellulosic biomass waste will become a problem for environmental health if not managed correctly. Biomass waste decomposition can produce methane gas which impacts climate change; it can also be a source of breeding pests and diseases. Various efforts have been made to utilize the waste so that it has an added economic value and is environmentally friendly. One of the waste utilization techniques is the carbonization of lignocellulosic biomass into charcoal and liquid smoke. Discussion: A literature review used the articles from Science Direct, Pubmed, Google Scholar, and Research Gate databases over ten years. This literature review paper aims to provide information on producing and utilizing liquid smoke and concludes with some suggestions on production and application. The literature review results show evidence that liquid smoke has been used since the time of the Neanderthals. Then, since the early nineteen century, liquid smoke has been applied in agriculture as plant growth, soil treatment, pesticide, antimicrobial, rubber coagulant/deodorizer, and antioxidant. Conclusion: A significant contribution of liquid smoke utilization is all lignocellulosic biomass waste that can be carbonized into charcoal and liquid smoke so that it can reduce waste problems. Therefore, liquid smoke can reduce the use of pesticides, herbicides, and insect repellents made from synthetic chemicals that can poison the environment. Not much research has been produced and utilized liquid smoke in the pyrolysis temperature stratification technique. So, there are still quite a lot of research opportunities for the diversification of liquid smoke production.


  • Open Access

    A Novel Mesoporous Activated Carbon Derived from Calliandra calothyrsus via Physical Activation: Saturation and Superheated

    by Nur Adi Saputra, Saptadi Darmawan, Lisna Efiyanti, Djeni Hendra, Santiyo Wibowo, Adi Santoso, Djarwanto, Gusmailina, Sri Komarayati, Dian Anggraini Indrawan, et al.

    In this work, both pyrochar and activated carbon were prepared by physical activation (i.e., saturation and superheated) by involving a thermal agent as a comparison. The effects of three agents on the pore development of activated carbon from a new material, Calliandra calothyrsus, were observed in detail. The BET surface area and the iodine index of the prepared activated carbon were used as pyrochar selection. Proximate, ultimate, XRD, FTIR, TGA, and SEM were used to characterize the physical and chemical properties of the product. Pyrochar pores were found to develop significantly at 350 °C, indicated by an increase in the BET surface area and iodine index. Pyrochar from a temperature of 350 °C was then selected as a precursor of activated carbon. S–SS and SS–S activated carbon samples were declared to have the highest iodine index (870 mg/g) and the highest BET surface area (642 m2/g), respectively. The pore distribution data showed that the superheated agent widened the pore and provided an active site for iodine adsorption, while the saturation agent resulted in a narrower pore for an increase in the BET surface area. S–SS has a lower C fraction and higher O fraction than SS–S. The SS–S samples have both Vol and Volmic for an increased BET surface area. The number of aromatic layers and –OH functional groups of the S–SS sample is more convenient for iodine enhancement than for increasing the BET surface area. Less water droplets and greater energy from superheated resulting pores widen, increasing the aromatic layer and providing additional functional groups.


  • Open Access

    Pharmacological Activity and Phytochemical Profile of Acacia Heartwood Extracts

    by Yanico Hadi Prayogo, Wasrin Syafii, Rita Kartika Sari, Irmanida Batubara, Danu

    Reactive oxygen species (ROS) are related to several degenerative diseases. In this study, Acacia, a genus with many fast-growing species, was investigated to explore the many phytochemical compounds that are biologically active in processes dealing with ROS-related diseases. This study aimed to select extracts of Acacia heartwood on the basis of their pharmacological and phytochemical profiles and identify their bioactive compounds. Five methanolic extracts from Acacia heartwood were evaluated for their antioxidant activity using three different in vitro assays: toxicity toward Artemia salina and phenolic and polyphenolic content. Multivariate analysis was conducted to select two promising extracts and then their bioactive compounds were identified using liquid chromatography coupled with mass spectrometry. Acacia crassicarpa extracts showed the highest antioxidant activity, as well as phenolic and hydrolyzable tannin contents, but low toxicity. The A. mangium extract exhibited high flavonoid and condensed tannin content, whereas A. decurrrens had the highest toxicity with low antioxidant activity. Pearson’s correlation analysis demonstrated no correlation between antioxidant activity and toxicity. Moreover, the phytochemical profile exhibited an association with pharmacological parameters. Principal component analysis followed by cluster analysis divided the extracts into three clusters. Two heartwood extracts of A. crassicarpa and A. auriculiformis were chosen as the best extracts. Identification showed that these extracts were dominated by phenolic compounds, as well as anthraquinone and xanthone.