CECaitlin Evans

Caitlin Evans

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article


Caitlin Evans has a total of 11 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Open Access

    Evaluation of Hammermill Tip Speed, Air Assist, and Screen Hole Diameter on Ground Corn Characteristics

    by Michaela Braun, Haley Wecker, Kara Dunmire, Caitlin Evans, Michael W. Sodak, Maks Kapetanovich, Jerry Shepherd, Randy Fisher, Kyle Coble, Charles Stark, et al.

    This study was performed to evaluate hammermill tip speed, assistive airflow, and screen hole diameter on hammermill throughput and characteristics of ground corn. Corn was ground using two Andritz hammermills measuring 1 m in diameter each equipped with 72 hammers and 300 HP motors. Treatments were arranged in a 3 × 3 × 3 factorial design with three tip speeds (3774, 4975, and 6176 m/min), three screen hole diameters (2.3, 3.9, and 6.3 mm), and three air flow rates (1062, 1416, and 1770 fan revolutions per minute). Corn was ground on three separate days to create three replications and treatments were randomized within day. Samples were collected and analyzed for moisture, particle size, and flowability characteristics. There was a 3-way interaction (p = 0.029) for standard deviation (Sgw). There was a screen hole diameter × hammer tip speed interaction (p < 0.001) for geometric mean particle size dgw (p < 0.001) and composite flow index (CFI) (p < 0.001). When tip speed increased from 3774 to 6176 m/min, the rate of decrease in dgw was greater as screen hole diameter increased from 2.3 to 6.3 mm. For CFI, increasing tip speed decreased the CFI of ground corn when ground using the 3.9 and 6.3 mm screen. However, when grinding corn using the 2.3 mm screen, there was no evidence of difference in CFI when increasing tip speed. In conclusion, the air flow rate did not influence dgw of corn, but hammer tip speed and screen size were altered and achieved a range of dgw from 304 to 617 µm.


  • Open Access

    Effects of Grinding Corn with Different Moisture Content on Subsequent Particle Size and Flowability

    by Michaela Braun, Kara Dunmire, Caitlin Evans, Charles Stark, Jason Woodworth, Chad Paulk

    The objective of this study was to determine the effects of whole-corn moisture and hammermill screen size on subsequent ground corn moisture, particle size and flowability. Treatments were arranged as a 2 × 2 factorial design with two moisture concentrations (14.5 and 16.7%), each ground using 2 hammermill screen sizes (3 mm and 6 mm). Corn was ground using a lab-scale 1.5 HP Bliss Hammermill at three separate timepoints to create three replications per treatment. Ground corn flowability was calculated using angle of repose (AOR), percent compressibility, and critical orifice diameter (COD) measurements to determine the composite flow index (CFI). There was no evidence for a screen size × corn moisture interaction for ground corn moisture content (MC), particle size, standard deviation, or flowability metrics. Grinding corn using a 3 mm screen resulted in decreased (p < 0.041) moisture content compared to corn ground using the 6 mm screen. There was a decrease (p < 0.031) in particle size from the 6 mm screen to the 3 mm, but no evidence of difference was observed for the standard deviation. There was a decrease (p < 0.030) in percent compressibility as screen size increased from 3 mm to 6 mm. Angle of repose tended to decrease (p < 0.056) when corn was ground using a 6 mm screen compared to a 3 mm screen. For the main effects of MC, 16.7% moisture corn had increased (p < 0.001) ground corn MC compared to 14.5%. The 14.5% moisture corn resulted in decreased (p < 0.050) particle size and an increased standard deviation compared to the 16.7% moisture corn. The increased MC of corn increased (p < 0.038) CFI and tended to decrease (p < 0.050) AOR and COD. In conclusion, decreasing hammermill screen size increased moisture loss by 0.55%, decreased corn particle size by 126 µm and resulted in poorer flowability as measured by percent compressibility and AOR. The higher moisture corn increased subsequent particle size by 89 µm and had improved flowability as measured by CFI.