Michaela Braun
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Michaela Braun has a total of 30 co-authors. Here are the top co-authors by number of shared publications:
J. C. Woodworth
5 shared publicationsC. B. Paulk
4 shared publications- Kara M. Dunmire
Kansas Agricultural Experiment Station Research Reports Kansas Agricultural Experiment Station Kansas State University Kansas State University Kansas State University Kansas State University Kansas State University Manhattan Kansas
4 shared publications - Caitlin E. Evans
Kansas State University Kansas State University Kansas State University
3 shared publications - Chad B. Paulk
Kansas State University
3 shared publications - Charles R. Stark
Kansas State University
3 shared publications
Latest Publications
- Open Access
Evaluation of Hammermill Tip Speed, Air Assist, and Screen Hole Diameter on Ground Corn Characteristics
This study was performed to evaluate hammermill tip speed, assistive airflow, and screen hole diameter on hammermill throughput and characteristics of ground corn. Corn was ground using two Andritz hammermills measuring 1 m in diameter each equipped with 72 hammers and 300 HP motors. Treatments were arranged in a 3 × 3 × 3 factorial design with three tip speeds (3774, 4975, and 6176 m/min), three screen hole diameters (2.3, 3.9, and 6.3 mm), and three air flow rates (1062, 1416, and 1770 fan revolutions per minute). Corn was ground on three separate days to create three replications and treatments were randomized within day. Samples were collected and analyzed for moisture, particle size, and flowability characteristics. There was a 3-way interaction (p = 0.029) for standard deviation (Sgw). There was a screen hole diameter × hammer tip speed interaction (p < 0.001) for geometric mean particle size dgw (p < 0.001) and composite flow index (CFI) (p < 0.001). When tip speed increased from 3774 to 6176 m/min, the rate of decrease in dgw was greater as screen hole diameter increased from 2.3 to 6.3 mm. For CFI, increasing tip speed decreased the CFI of ground corn when ground using the 3.9 and 6.3 mm screen. However, when grinding corn using the 2.3 mm screen, there was no evidence of difference in CFI when increasing tip speed. In conclusion, the air flow rate did not influence dgw of corn, but hammer tip speed and screen size were altered and achieved a range of dgw from 304 to 617 µm.
Open AccessEvaluation of Hammermill Tip Speed, Air Assist, and Screen Hole Diameter on Ground Corn Characteristics
This study was performed to evaluate hammermill tip speed, assistive airflow, and screen hole diameter on hammermill throughput and characteristics of ground corn. Corn was ground using two Andritz hammermills measuring 1 m in diameter each equipped with 72 hammers and 300 HP motors. Treatments were arranged in a 3 × 3 × 3 factorial design with three tip speeds (3774, 4975, and 6176 m/min), three screen hole diameters (2.3, 3.9, and 6.3 mm), and three air flow rates (1062, 1416, and 1770 fan revolutions per minute). Corn was ground on three separate days to create three replications and treatments were randomized within day. Samples were collected and analyzed for moisture, particle size, and flowability characteristics. There was a 3-way interaction (p = 0.029) for standard deviation (Sgw). There was a screen hole diameter × hammer tip speed interaction (p < 0.001) for geometric mean particle size dgw (p < 0.001) and composite flow index (CFI) (p < 0.001). When tip speed increased from 3774 to 6176 m/min, the rate of decrease in dgw was greater as screen hole diameter increased from 2.3 to 6.3 mm. For CFI, increasing tip speed decreased the CFI of ground corn when ground using the 3.9 and 6.3 mm screen. However, when grinding corn using the 2.3 mm screen, there was no evidence of difference in CFI when increasing tip speed. In conclusion, the air flow rate did not influence dgw of corn, but hammer tip speed and screen size were altered and achieved a range of dgw from 304 to 617 µm.
- Open Access
Effects of Grinding Corn with Different Moisture Content on Subsequent Particle Size and Flowability
The objective of this study was to determine the effects of whole-corn moisture and hammermill screen size on subsequent ground corn moisture, particle size and flowability. Treatments were arranged as a 2 × 2 factorial design with two moisture concentrations (14.5 and 16.7%), each ground using 2 hammermill screen sizes (3 mm and 6 mm). Corn was ground using a lab-scale 1.5 HP Bliss Hammermill at three separate timepoints to create three replications per treatment. Ground corn flowability was calculated using angle of repose (AOR), percent compressibility, and critical orifice diameter (COD) measurements to determine the composite flow index (CFI). There was no evidence for a screen size × corn moisture interaction for ground corn moisture content (MC), particle size, standard deviation, or flowability metrics. Grinding corn using a 3 mm screen resulted in decreased (p < 0.041) moisture content compared to corn ground using the 6 mm screen. There was a decrease (p < 0.031) in particle size from the 6 mm screen to the 3 mm, but no evidence of difference was observed for the standard deviation. There was a decrease (p < 0.030) in percent compressibility as screen size increased from 3 mm to 6 mm. Angle of repose tended to decrease (p < 0.056) when corn was ground using a 6 mm screen compared to a 3 mm screen. For the main effects of MC, 16.7% moisture corn had increased (p < 0.001) ground corn MC compared to 14.5%. The 14.5% moisture corn resulted in decreased (p < 0.050) particle size and an increased standard deviation compared to the 16.7% moisture corn. The increased MC of corn increased (p < 0.038) CFI and tended to decrease (p < 0.050) AOR and COD. In conclusion, decreasing hammermill screen size increased moisture loss by 0.55%, decreased corn particle size by 126 µm and resulted in poorer flowability as measured by percent compressibility and AOR. The higher moisture corn increased subsequent particle size by 89 µm and had improved flowability as measured by CFI.
Open AccessEffects of Grinding Corn with Different Moisture Content on Subsequent Particle Size and Flowability
The objective of this study was to determine the effects of whole-corn moisture and hammermill screen size on subsequent ground corn moisture, particle size and flowability. Treatments were arranged as a 2 × 2 factorial design with two moisture concentrations (14.5 and 16.7%), each ground using 2 hammermill screen sizes (3 mm and 6 mm). Corn was ground using a lab-scale 1.5 HP Bliss Hammermill at three separate timepoints to create three replications per treatment. Ground corn flowability was calculated using angle of repose (AOR), percent compressibility, and critical orifice diameter (COD) measurements to determine the composite flow index (CFI). There was no evidence for a screen size × corn moisture interaction for ground corn moisture content (MC), particle size, standard deviation, or flowability metrics. Grinding corn using a 3 mm screen resulted in decreased (p < 0.041) moisture content compared to corn ground using the 6 mm screen. There was a decrease (p < 0.031) in particle size from the 6 mm screen to the 3 mm, but no evidence of difference was observed for the standard deviation. There was a decrease (p < 0.030) in percent compressibility as screen size increased from 3 mm to 6 mm. Angle of repose tended to decrease (p < 0.056) when corn was ground using a 6 mm screen compared to a 3 mm screen. For the main effects of MC, 16.7% moisture corn had increased (p < 0.001) ground corn MC compared to 14.5%. The 14.5% moisture corn resulted in decreased (p < 0.050) particle size and an increased standard deviation compared to the 16.7% moisture corn. The increased MC of corn increased (p < 0.038) CFI and tended to decrease (p < 0.050) AOR and COD. In conclusion, decreasing hammermill screen size increased moisture loss by 0.55%, decreased corn particle size by 126 µm and resulted in poorer flowability as measured by percent compressibility and AOR. The higher moisture corn increased subsequent particle size by 89 µm and had improved flowability as measured by CFI.
- Open Access
- 1 January 2020
- Published by Kansas State University in Kansas Agricultural Experiment Station Research Reports
- Vol. 6 (10) , 28
Evaluation of Conditioning Temperature and Die Specifications on Nursery Pig Performance
The objective of this study was to determine the effects on growth performance in nursery pigs that is linked to the conditioning temperature and die specifications used during the feed pelleting process. A total of 315 barrows (DNA; 200 × 400; initial BW 13.2 lb) were used in a 35-d growth trial. Upon arrival, pigs were weighed and assigned to pens in a completely randomized design with 5 pigs per pen, and each pen was randomly assigned to 1 of 7 dietary treatments with 9 replications per treatment. Treatments consisted of a mash control (MC) and 6 pelleted diets manufactured using 2 different pellet dies (length/diameter [L:D]: 6.7 and 2.7) and 3 different conditioning temperatures (low, medium, high). Conditioning temperatures for Phase 1 diets pelleted using the 6.7 L:D die were 80, 100, and 120°F and for the die with a L:D 2.7 were 100, 120, and 140°F for the low, medium, and high, respectively. Phase 2 conditioning temperatures for diets pelleted using the die with a L:D of 6.7 were approximately 120, 140, and 160°F and for the 2.7 L:D die were 140, 160, and 180°F for the low, medium, and high, respectively. Diets were fed in three phases as follows, Phase 1: d 0 to 10, Phase 2: d 10 to 25, and Phase 3: d 25 to 35. During Phase 3 all pigs were fed a common mash diet. Overall from d 0 to 35, similar ADG was observed for pigs fed the MC or pelleted diets with the exception of the diet pelleted at the low conditioning temperature using the 6.7 L:D die, which had decreased (P < 0.05) ADG compared to MC. When pelleting diets using the 2.7 L:D die, there was a tendency for increased (quadratic, P = 0.077) ADG in pigs fed diets conditioned at increasing temperatures, with the medium temperature having the greatest ADG. There was a tendency for increased (P = 0.088) ADG in pigs fed diets pelleted using the 2.7 L:D die compared to the 6.7 L:D die. Pigs fed pelleted diets, with the exception of the medium temperature on the 2.7 L:D die, had decreased (P < 0.05) ADFI compared to the MC. However, diets pelleted using the 6.7 L:D die as well as the diet manufactured at the medium conditioning temperature on the 2.7 L:D die had improved (P < 0.05) F/G compared to the MC diet. Additionally,
- 1 January 2020
- Published by Kansas State University in Kansas Agricultural Experiment Station Research Reports
- Vol. 6 (10) , 28
Open AccessEvaluation of Conditioning Temperature and Die Specifications on Nursery Pig Performance
The objective of this study was to determine the effects on growth performance in nursery pigs that is linked to the conditioning temperature and die specifications used during the feed pelleting process. A total of 315 barrows (DNA; 200 × 400; initial BW 13.2 lb) were used in a 35-d growth trial. Upon arrival, pigs were weighed and assigned to pens in a completely randomized design with 5 pigs per pen, and each pen was randomly assigned to 1 of 7 dietary treatments with 9 replications per treatment. Treatments consisted of a mash control (MC) and 6 pelleted diets manufactured using 2 different pellet dies (length/diameter [L:D]: 6.7 and 2.7) and 3 different conditioning temperatures (low, medium, high). Conditioning temperatures for Phase 1 diets pelleted using the 6.7 L:D die were 80, 100, and 120°F and for the die with a L:D 2.7 were 100, 120, and 140°F for the low, medium, and high, respectively. Phase 2 conditioning temperatures for diets pelleted using the die with a L:D of 6.7 were approximately 120, 140, and 160°F and for the 2.7 L:D die were 140, 160, and 180°F for the low, medium, and high, respectively. Diets were fed in three phases as follows, Phase 1: d 0 to 10, Phase 2: d 10 to 25, and Phase 3: d 25 to 35. During Phase 3 all pigs were fed a common mash diet. Overall from d 0 to 35, similar ADG was observed for pigs fed the MC or pelleted diets with the exception of the diet pelleted at the low conditioning temperature using the 6.7 L:D die, which had decreased (P < 0.05) ADG compared to MC. When pelleting diets using the 2.7 L:D die, there was a tendency for increased (quadratic, P = 0.077) ADG in pigs fed diets conditioned at increasing temperatures, with the medium temperature having the greatest ADG. There was a tendency for increased (P = 0.088) ADG in pigs fed diets pelleted using the 2.7 L:D die compared to the 6.7 L:D die. Pigs fed pelleted diets, with the exception of the medium temperature on the 2.7 L:D die, had decreased (P < 0.05) ADFI compared to the MC. However, diets pelleted using the 6.7 L:D die as well as the diet manufactured at the medium conditioning temperature on the 2.7 L:D die had improved (P < 0.05) F/G compared to the MC diet. Additionally,
- Open Access
- 1 January 2019
- Published by Kansas State University in Kansas Agricultural Experiment Station Research Reports
- Vol. 5 (8) , 38
Effects of Grinding Corn with Different Moisture Concentrations on Subsequent Particle Size and Flowability Characteristics
The objective of this study was to determine the effects of whole corn moisture and hammermill screen size on subsequent ground corn moisture, particle size, and flow- ability. Whole yellow dent #2 corn was used for this experiment. Treatments were arranged as a 2 × 2 factorial design with two moisture concentrations (as-received and high) each ground using 2 hammermill screen sizes (1/8 and 1/4 in). Corn was ground using a laboratory scale 1.5 HP Bliss Hammermill (Model 6K630B) at 3 separate time points to create 3 replications per treatment. Increasing initial whole corn moisture was accomplished by adding 5% water and heating at 55°C for 3 hours in sealed glass jars using a Fisherbrand Isotemp Oven (Model 15-103-051). Ground corn flowability was calculated using angle of repose (AOR), percent compressibility, and critical orifice diameter (COD) measurements to determine the composite flow index (CFI). There was no evidence for a screen size × corn moisture interaction for moisture content, particle size, standard deviation, or flowability metrics. Grinding corn using a 1/8 in screen resulted in decreased (P < 0.041) moisture content compared to corn ground using the 1/4 in screen. There was a decrease in particle size from the 1/4 in screen to the 1/8 in but no evidence of difference was observed for the standard deviation. There was a decrease (P < 0.03) in percent compressibility as screen size increased from 1/8 to 1/4 in. Angle of repose tended to decrease (P < 0 .056) when corn was ground using a 1/4 in screen compared to a 1/8 in screen. For the main effects of moisture content, high moisture corn had increased (P < 0.0001) ground corn moisture content compared to as-received corn. As-received corn resulted in decreased (P < 0.029) particle size and an increased standard deviation compared to the high moisture corn. Increased moisture content of corn increased (P < 0.038) CFI and tended to decrease (P < 0.056) AOR and COD. In conclusion, decreasing hammermill screen size increased moisture loss by 0.55%, corn particle size by 126 μm, and resulted in poorer flowability as measured by percent compressibility and AOR. High moisture corn increased subsequent particle size by 89 μm, therefore improving flowability as measured by CFI.
- 1 January 2019
- Published by Kansas State University in Kansas Agricultural Experiment Station Research Reports
- Vol. 5 (8) , 38
Open AccessEffects of Grinding Corn with Different Moisture Concentrations on Subsequent Particle Size and Flowability Characteristics
The objective of this study was to determine the effects of whole corn moisture and hammermill screen size on subsequent ground corn moisture, particle size, and flow- ability. Whole yellow dent #2 corn was used for this experiment. Treatments were arranged as a 2 × 2 factorial design with two moisture concentrations (as-received and high) each ground using 2 hammermill screen sizes (1/8 and 1/4 in). Corn was ground using a laboratory scale 1.5 HP Bliss Hammermill (Model 6K630B) at 3 separate time points to create 3 replications per treatment. Increasing initial whole corn moisture was accomplished by adding 5% water and heating at 55°C for 3 hours in sealed glass jars using a Fisherbrand Isotemp Oven (Model 15-103-051). Ground corn flowability was calculated using angle of repose (AOR), percent compressibility, and critical orifice diameter (COD) measurements to determine the composite flow index (CFI). There was no evidence for a screen size × corn moisture interaction for moisture content, particle size, standard deviation, or flowability metrics. Grinding corn using a 1/8 in screen resulted in decreased (P < 0.041) moisture content compared to corn ground using the 1/4 in screen. There was a decrease in particle size from the 1/4 in screen to the 1/8 in but no evidence of difference was observed for the standard deviation. There was a decrease (P < 0.03) in percent compressibility as screen size increased from 1/8 to 1/4 in. Angle of repose tended to decrease (P < 0 .056) when corn was ground using a 1/4 in screen compared to a 1/8 in screen. For the main effects of moisture content, high moisture corn had increased (P < 0.0001) ground corn moisture content compared to as-received corn. As-received corn resulted in decreased (P < 0.029) particle size and an increased standard deviation compared to the high moisture corn. Increased moisture content of corn increased (P < 0.038) CFI and tended to decrease (P < 0.056) AOR and COD. In conclusion, decreasing hammermill screen size increased moisture loss by 0.55%, corn particle size by 126 μm, and resulted in poorer flowability as measured by percent compressibility and AOR. High moisture corn increased subsequent particle size by 89 μm, therefore improving flowability as measured by CFI.
- Open Access
- 1 January 2019
- Published by Kansas State University in Kansas Agricultural Experiment Station Research Reports
- Vol. 5 (8) , 10
Effects of Spray-Dried Lactococcus-Based Fermentation Products on Growth Performance of Nursery Pigs
A total of 720 barrows (initially 13.0 lb; Line 200 × 400; DNA, Columbus, NE) from 2 study groups (360 pigs per study group), were used in a 42-d growth trial to test the effects of spray-dried Lactococcus-based fermentation products on nursery pig performance. There were 24 replications per treatment and 5 pigs per pen. For both experiments, pens of pigs were randomly allotted to 1 of 6 dietary treatments in a completely randomized design. There were six treatment diets fed in 3 phases. The positive control diet included zinc oxide (phase 1), zinc oxide + chlortetracycline (CTC; phase 2) while the negative control diet did not include zinc oxide or CTC. Treatment diets included the negative control + 1 of 4 fermentation products (C, D, E, or F) added at 5% of the diet. Phase 3 diets contained a common control diet fed to all pigs plus treatment diets (C, D, E, and F). Phase 1 and 2 diets were fed in pelleted form and phase 3 in mash form. From d 0 to 20, there was an overall treatment effect (P = 0.001) where pigs fed the positive control had increased (P < 0.05) d 20 weight, average daily gain (ADG), average daily intake (ADFI), and improved feed efficiency (F/G) compared to those fed the negative control and negative control + fermentation product. From d 20 to 42, there was an overall treatment effect (P = 0.003) for F/G where pigs fed the negative control had improved (P < 0.05) F/G compared to those fed additive D, E, and F. Overall, there was a treatment effect (P = 0.03) for pigs fed the positive control having improved (P < 0.05) ADG and F/G compared to the negative control and negative control + fermentation product. In addition, pigs fed the negative control had improved (P < 0.05) F/G compared to those fed additive D, E, and F. In conclusion, pigs fed the positive control (zinc + CTC) diet had improved performance compared to pigs fed the negative control with or without fermentation product.
- 1 January 2019
- Published by Kansas State University in Kansas Agricultural Experiment Station Research Reports
- Vol. 5 (8) , 10
Open AccessEffects of Spray-Dried Lactococcus-Based Fermentation Products on Growth Performance of Nursery Pigs
A total of 720 barrows (initially 13.0 lb; Line 200 × 400; DNA, Columbus, NE) from 2 study groups (360 pigs per study group), were used in a 42-d growth trial to test the effects of spray-dried Lactococcus-based fermentation products on nursery pig performance. There were 24 replications per treatment and 5 pigs per pen. For both experiments, pens of pigs were randomly allotted to 1 of 6 dietary treatments in a completely randomized design. There were six treatment diets fed in 3 phases. The positive control diet included zinc oxide (phase 1), zinc oxide + chlortetracycline (CTC; phase 2) while the negative control diet did not include zinc oxide or CTC. Treatment diets included the negative control + 1 of 4 fermentation products (C, D, E, or F) added at 5% of the diet. Phase 3 diets contained a common control diet fed to all pigs plus treatment diets (C, D, E, and F). Phase 1 and 2 diets were fed in pelleted form and phase 3 in mash form. From d 0 to 20, there was an overall treatment effect (P = 0.001) where pigs fed the positive control had increased (P < 0.05) d 20 weight, average daily gain (ADG), average daily intake (ADFI), and improved feed efficiency (F/G) compared to those fed the negative control and negative control + fermentation product. From d 20 to 42, there was an overall treatment effect (P = 0.003) for F/G where pigs fed the negative control had improved (P < 0.05) F/G compared to those fed additive D, E, and F. Overall, there was a treatment effect (P = 0.03) for pigs fed the positive control having improved (P < 0.05) ADG and F/G compared to the negative control and negative control + fermentation product. In addition, pigs fed the negative control had improved (P < 0.05) F/G compared to those fed additive D, E, and F. In conclusion, pigs fed the positive control (zinc + CTC) diet had improved performance compared to pigs fed the negative control with or without fermentation product.
- Open Access
- 1 January 2018
- Published by Kansas State University in Kansas Agricultural Experiment Station Research Reports
- Vol. 4 (9) , 32
Effect of Dietary Fiber Source on Growth Performance, Carcass Characteristics, and Economic Return of Finishing Pigs
A total of 287 pigs (DNA 600 × 241; initially 111.8 lb) were used in an 86-d experiment to determine the effect of dietary fiber source on finishing pig growth performance and carcass characteristics. There were 12 pens per treatment with 7 or 8 pigs per pen. Pens were randomly assigned to 1 of 3 dietary treatments consisting of a control (8.7% neutral detergent fiber; NDF), 20% dried distillers grains with solubles (DDGS; 13.6% NDF), or 14.5% sugar beet pulp (SBP; 13.6% NDF). Experimental diets were fed from d 0 to 86 in 3 phases; d 0 to 18, d 18 to 39, and d 39 to 86. From d 0 to 86, there was no evidence for treatment difference in ADG or ADFI. Pigs fed DDGS had marginally poorer F/G than the control or 14.5% SBP diets (P < 0.10). Caloric efficiency of net energy (NE) in kcal per lb of live gain was marginally poorer (P < 0.10) in pigs fed DDGS compared to those fed control and SBP. There was a decrease (P < 0.10) in hot carcass weight (HCW) and carcass yield (P < .0.05) in pigs fed DDGS and SBP compared to those fed the control diet. Loin depth marginally decreased (P < 0.10) in pigs fed SBP compared to the control, with those fed DDGS intermediate. Feed cost per pig was greatest (P < 0.05) for pigs fed SBP, followed by DDGS, with those fed the control diet having the least. Feed cost per lb of gain increased (P < 0.05) in pigs fed SBP, followed by DDGS, with those fed the control having the least. Gain value decreased (P < 0.05) in pigs fed SBP compared to the control, with those fed DDGS intermediate. Income over feed cost was poorest (P < 0.05) in pigs fed SBP, followed by DDGS, with those fed the control diet being the greatest. In conclusion, pigs fed DDGS tended to have poorer F/G compared to those fed the control diet or SBP. This can be explained by the overestimation of NE of the diet as demonstrated by an increase in caloric efficiency. Increasing dietary NDF reduced carcass yield and economic return.
- 1 January 2018
- Published by Kansas State University in Kansas Agricultural Experiment Station Research Reports
- Vol. 4 (9) , 32
Open AccessEffect of Dietary Fiber Source on Growth Performance, Carcass Characteristics, and Economic Return of Finishing Pigs
A total of 287 pigs (DNA 600 × 241; initially 111.8 lb) were used in an 86-d experiment to determine the effect of dietary fiber source on finishing pig growth performance and carcass characteristics. There were 12 pens per treatment with 7 or 8 pigs per pen. Pens were randomly assigned to 1 of 3 dietary treatments consisting of a control (8.7% neutral detergent fiber; NDF), 20% dried distillers grains with solubles (DDGS; 13.6% NDF), or 14.5% sugar beet pulp (SBP; 13.6% NDF). Experimental diets were fed from d 0 to 86 in 3 phases; d 0 to 18, d 18 to 39, and d 39 to 86. From d 0 to 86, there was no evidence for treatment difference in ADG or ADFI. Pigs fed DDGS had marginally poorer F/G than the control or 14.5% SBP diets (P < 0.10). Caloric efficiency of net energy (NE) in kcal per lb of live gain was marginally poorer (P < 0.10) in pigs fed DDGS compared to those fed control and SBP. There was a decrease (P < 0.10) in hot carcass weight (HCW) and carcass yield (P < .0.05) in pigs fed DDGS and SBP compared to those fed the control diet. Loin depth marginally decreased (P < 0.10) in pigs fed SBP compared to the control, with those fed DDGS intermediate. Feed cost per pig was greatest (P < 0.05) for pigs fed SBP, followed by DDGS, with those fed the control diet having the least. Feed cost per lb of gain increased (P < 0.05) in pigs fed SBP, followed by DDGS, with those fed the control having the least. Gain value decreased (P < 0.05) in pigs fed SBP compared to the control, with those fed DDGS intermediate. Income over feed cost was poorest (P < 0.05) in pigs fed SBP, followed by DDGS, with those fed the control diet being the greatest. In conclusion, pigs fed DDGS tended to have poorer F/G compared to those fed the control diet or SBP. This can be explained by the overestimation of NE of the diet as demonstrated by an increase in caloric efficiency. Increasing dietary NDF reduced carcass yield and economic return.
- Open Access
- 1 January 2018
- Published by Kansas State University in Kansas Agricultural Experiment Station Research Reports
- Vol. 4 (9) , 43
Effect of Mill Type and Particle Size Variation on Growth Performance and Carcass Characteristics of Finishing Pigs
The objective of this experiment was to determine the effects of mill type used to grind corn and its particle size variation on diet flowability and subsequent finishing pig growth performance and carcass characteristics. A total of 200 pigs (DNA Line 241 × 600; initially 121.9 lb) were used in a 75-d growth trial. Pigs were randomly assigned to pens with either 5 barrows or 5 gilts per pen. Pens were then randomly allotted to 1 of 4 treatments balanced by weight and gender with 10 pens per treatment. Treatments were arranged as a 2 × 2 factorial with 2 mill types (3-high roller mill; RMS, Model 924 or a hammermill; Bliss, model 22115) and 2 particle size variations (standard vs. blended). Increasing corn particle size variation was accomplished by blending 30% 400 μm corn, 40% 600 μm corn, and 30% 800 μm corn. Standard treatments were accomplished by grinding corn to an average of 600 μm with either mill. On d 75, pigs were transported to a commercial packing plant for processing and determination of carcass characteristics. The average analyzed complete diet mean particle sizes and standard deviations were 497, 540, 503, and 520 μm and 2.70, 2.75. 3.35, and 3.35 for the roller mill standard, roller mill blended, hammermill standard, and hammermill blended treatments, respectively. Diet flowability was calculated using angle of repose (AoR), percent compressibility, and critical orifice diameter (COD) measurements to determine the composite flow index (CFI). The AOR were 34.2, 33.0, 35.4, and 36.2º; COD were 32.0, 31.3, 30.0, and 33.0 mm; compressibilitys were 18.7, 18.4, 17.0, and 15.7%; and CFI were 52.9, 55.4, 53.9, and 53.2 for the roller mill standard, roller mill blended, hammermill standard, and hammermill blended treatments, respectively. There were no interactions or main effects of mill type on growth performance or carcass characteristics. However, pigs fed the blended diets had marginally significant decreased (P < 0.083) average daily gain (ADG) compared to those fed the standard diets. No differences were observed in total feed cost or cost per lb of gain between treatments. Pigs fed blended diets also had marginally decreased (P < 0.059) gain value and income over feed costs (IOFC) compared to those fed diets that were not blended. In conclusion, mill type used to grind corn and increasing particle size variation did not impact flowability metrics of complete diets. Mill type used to grind corn did not
- 1 January 2018
- Published by Kansas State University in Kansas Agricultural Experiment Station Research Reports
- Vol. 4 (9) , 43
Open AccessEffect of Mill Type and Particle Size Variation on Growth Performance and Carcass Characteristics of Finishing Pigs
The objective of this experiment was to determine the effects of mill type used to grind corn and its particle size variation on diet flowability and subsequent finishing pig growth performance and carcass characteristics. A total of 200 pigs (DNA Line 241 × 600; initially 121.9 lb) were used in a 75-d growth trial. Pigs were randomly assigned to pens with either 5 barrows or 5 gilts per pen. Pens were then randomly allotted to 1 of 4 treatments balanced by weight and gender with 10 pens per treatment. Treatments were arranged as a 2 × 2 factorial with 2 mill types (3-high roller mill; RMS, Model 924 or a hammermill; Bliss, model 22115) and 2 particle size variations (standard vs. blended). Increasing corn particle size variation was accomplished by blending 30% 400 μm corn, 40% 600 μm corn, and 30% 800 μm corn. Standard treatments were accomplished by grinding corn to an average of 600 μm with either mill. On d 75, pigs were transported to a commercial packing plant for processing and determination of carcass characteristics. The average analyzed complete diet mean particle sizes and standard deviations were 497, 540, 503, and 520 μm and 2.70, 2.75. 3.35, and 3.35 for the roller mill standard, roller mill blended, hammermill standard, and hammermill blended treatments, respectively. Diet flowability was calculated using angle of repose (AoR), percent compressibility, and critical orifice diameter (COD) measurements to determine the composite flow index (CFI). The AOR were 34.2, 33.0, 35.4, and 36.2º; COD were 32.0, 31.3, 30.0, and 33.0 mm; compressibilitys were 18.7, 18.4, 17.0, and 15.7%; and CFI were 52.9, 55.4, 53.9, and 53.2 for the roller mill standard, roller mill blended, hammermill standard, and hammermill blended treatments, respectively. There were no interactions or main effects of mill type on growth performance or carcass characteristics. However, pigs fed the blended diets had marginally significant decreased (P < 0.083) average daily gain (ADG) compared to those fed the standard diets. No differences were observed in total feed cost or cost per lb of gain between treatments. Pigs fed blended diets also had marginally decreased (P < 0.059) gain value and income over feed costs (IOFC) compared to those fed diets that were not blended. In conclusion, mill type used to grind corn and increasing particle size variation did not impact flowability metrics of complete diets. Mill type used to grind corn did not
- Open Access
- 1 January 2018
- Published by Kansas State University in Kansas Agricultural Experiment Station Research Reports
- Vol. 4 (9) , 4
Effects of a Bacillus-Based Probiotic on Sow Performance and on Progeny Growth Performance, Fecal Consistency, and Fecal Microflora
The objective of this study was to evaluate the effects of supplementation of Bacillus subtilis C- 3102 on sow performance and fecal microflora and on progeny growth performance, fecal consistency, and fecal microflora. For the sow portion of this study, a total of 29 sows (DNA 241, DNA Genetics, Columbus, NE) and litters were used from d 30 of gestation until weaning (d 19 of lactation). Treatments consisted of providing a control diet (n = 14 sows) or a probiotic diet (n = 15 sows) supplemented with Bacillus subtilis C-3102 (Calsporin®, Calpis Co. Ltd., Tokyo, Japan) at 500,000 CFU/g of complete feed in gestation and 1,000,000 CFU/g of complete feed in lactation. For the nursery portion of the study, a total of 358 weaned pigs (DNA 241 × 600, DNA Genetics, Columbus, NE) progeny of the sows on study, were used in a 42-d nursery trial. There were 4 or 5 pigs per pen and 18 or 19 replications per treatment. Treatments were arranged in a 2 × 2 factorial with main effects of sow treatment (control diet vs. probiotic diet) and nursery treatment (control diet vs. probiotic diet). In the nursery probiotic diet, a combination of the probiotic Bacillus subtilis C-3102 and prebiotics based on beta glucans and mannan oligosaccharides (BacPack ABF™, Quality Technology International, Inc., Elgin, IL) was included at 0.05% of complete feed. Fecal scoring was used to categorize fecal consistency of nursing litters and nursery pens. Fecal samples were collected from sows and piglets for microbial analysis performed by culture method and bacterial quantification. The results demonstrate that sows fed the probiotic diet had a marginally significant (P = 0.056) increase in lactation average daily feed intake (ADFI), consuming on average 0.6 lb more feed per day than sows fed the control diet, but it did not result (P > 0.10) in improvement in sow or piglet body weight (BW) at weaning. Sows fed the probiotic diet had marginally significant (P = 0.060) larger litter size after equalization on d 2 after birth, with on average 0.5 more piglet per litter than sows fed the control diet, but it did not result (P > 0.10) in larger litter size at weaning. In the nursery, there was no evidence for effect of sow treatment, nursery treatment, or interactions (P > 0.10) on overall growth performance. However, growth performance from d 21 to 42 and final nursery BW
- 1 January 2018
- Published by Kansas State University in Kansas Agricultural Experiment Station Research Reports
- Vol. 4 (9) , 4
Open AccessEffects of a Bacillus-Based Probiotic on Sow Performance and on Progeny Growth Performance, Fecal Consistency, and Fecal Microflora
The objective of this study was to evaluate the effects of supplementation of Bacillus subtilis C- 3102 on sow performance and fecal microflora and on progeny growth performance, fecal consistency, and fecal microflora. For the sow portion of this study, a total of 29 sows (DNA 241, DNA Genetics, Columbus, NE) and litters were used from d 30 of gestation until weaning (d 19 of lactation). Treatments consisted of providing a control diet (n = 14 sows) or a probiotic diet (n = 15 sows) supplemented with Bacillus subtilis C-3102 (Calsporin®, Calpis Co. Ltd., Tokyo, Japan) at 500,000 CFU/g of complete feed in gestation and 1,000,000 CFU/g of complete feed in lactation. For the nursery portion of the study, a total of 358 weaned pigs (DNA 241 × 600, DNA Genetics, Columbus, NE) progeny of the sows on study, were used in a 42-d nursery trial. There were 4 or 5 pigs per pen and 18 or 19 replications per treatment. Treatments were arranged in a 2 × 2 factorial with main effects of sow treatment (control diet vs. probiotic diet) and nursery treatment (control diet vs. probiotic diet). In the nursery probiotic diet, a combination of the probiotic Bacillus subtilis C-3102 and prebiotics based on beta glucans and mannan oligosaccharides (BacPack ABF™, Quality Technology International, Inc., Elgin, IL) was included at 0.05% of complete feed. Fecal scoring was used to categorize fecal consistency of nursing litters and nursery pens. Fecal samples were collected from sows and piglets for microbial analysis performed by culture method and bacterial quantification. The results demonstrate that sows fed the probiotic diet had a marginally significant (P = 0.056) increase in lactation average daily feed intake (ADFI), consuming on average 0.6 lb more feed per day than sows fed the control diet, but it did not result (P > 0.10) in improvement in sow or piglet body weight (BW) at weaning. Sows fed the probiotic diet had marginally significant (P = 0.060) larger litter size after equalization on d 2 after birth, with on average 0.5 more piglet per litter than sows fed the control diet, but it did not result (P > 0.10) in larger litter size at weaning. In the nursery, there was no evidence for effect of sow treatment, nursery treatment, or interactions (P > 0.10) on overall growth performance. However, growth performance from d 21 to 42 and final nursery BW