Current Organizations / Institutes

The organizations/institutes from the scholar's latest article


Christian Ferrarese has a total of 33 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Open Access

    Abrasion Rates and Service Life of C2 Tyres for Vans

    by Barouch Giechaskiel, Christian Ferrarese, Theodoros Grigoratos, Vicente Franco

    Vans (light commercial vehicles) account for only about 11% of the European light-duty vehicle fleet. However, they are mostly used in urban delivery and service operations where frequent stop-and-go driving increases tyre abrasion. Furthermore, their annual mileage is on average more than 70% higher than that of passenger cars. For these reasons, vans are estimated to generate tyre wear emissions that are at least 2.5 times higher than those of passenger cars on a per-vehicle basis, and therefore make a disproportionate contribution to microplastic pollution in cities. The Euro 7 pollutant emission standards introduce, for the first time, regulatory limits on tyre abrasion for passenger car tyres (C1 class) from 2028 and for light-commercial-vehicle tyres (C2 class) from 2030, building on United Nations (UN) tyre testing procedures developed under UN Regulation 117. While two candidate test methods (a real-world method and a laboratory method) have been agreed on for C1 tyres, no equivalent standard exists yet for C2 tyres, and very few experimental data have been published so far. In this study, we adapt the C1 real-world-based method to winter C2 tyres (snow three-peak mountain snowflake, 3PMSF) fitted to vans, and we discuss the practical and regulatory challenges encountered. The resulting abrasion rate and abrasion level indices provide first experimental emission factors for C2 tyres and can inform the ongoing development of regulatory test procedures and limit values for van tyres. We also develop an experimental and analytical framework to relate abrasion measurements to tyre service life (mileage potential).

  • Open Access

    Wear of Passenger Car C1 Tyres Under Regulatory On-Road Testing Conditions

    by Barouch Giechaskiel, Christian Ferrarese, Theodoros Grigoratos, Vicente Franco

    Tyre wear is a major contributor to global microplastic pollution, affecting air, soil, water, and wildlife as well as human health. In the European Union (EU), the latest Euro 7 regulation foresees the introduction of tyre abrasion limits covering all tyre categories, referring to two testing methods (convoy on road or laboratory drum) developed by the United Nations (UN) Economic Commission for Europe (UNECE) World Forum for Harmonization of Vehicle Regulations (WP.29). In this study, we applied the convoy method adopted by the UNECE Working Group on Noise and Tyres (GRBP) as part of the UN Regulation 117 on tyre performance parameters. The method has been developed by the Task Force on Tyre Abrasion (TFTA) of the UNECE and involves vehicles driving on public roads for about 8000 km. Candidate and reference tyres are fitted in a convoy of up to four vehicles, and an abrasion index for each candidate tyre is determined as a ratio of the abrasion of the candidate and reference tyres. In our tests, in addition to the abrasion rate, we measured the tread depth reduction and defined a service life index (i.e., total mileage potential) without the need of a different methodology. The results from six summer and nine winter C1 class passenger car tyres of various sizes showed a wide range of abrasion rates and service life values. We also compared our results with values reported in the literature and on websites. The conclusions of this study are expected to support the ongoing discussion on limit setting for C1 tyres and the definition of a service life index.


  • Open Access

    Tire Wear, Tread Depth Reduction, and Service Life

    by Barouch Giechaskiel, Christian Ferrarese, Theodoros Grigoratos

    Tires are important for the transmission of forces, good traction of the vehicle, and safety of the passengers. Tires also influence vehicle fuel consumption and cause tire and road wear pollution to the environment in the form of microplastics. In the United States, the Uniform Tire Quality Grading (UTQG) for tread wear is reported on the tire sidewall and is used as an indicator of the expected service life of a tire. In Europe, a similar approach that applies tread depth reduction measurements and projection to the minimum tread depth is under discussion. Tread depth measurements will be carried out in parallel with abrasion measurements over the recently introduced abrasion rate test in the United Nations regulation 117. Testing is carried out with an on-road convoy method accompanied by a vehicle fitted with reference tires to minimize the influence of external parameters. In this brief review, we start with a short historical overview of the methods that have been applied so far for the measurement of tire service life. Based on the limited publicly available data, we calculate the average tread depth reduction per distance driven for summer and winter tires fitted both in the front and rear axles of passenger cars (1–1.2 mm for front wheels and 0.5–0.6 mm for rear wheels per 10,000 km). We theoretically estimate the tread mass loss per mm of tread depth reduction (250 g per 1 mm tread depth reduction, depending on the tire size) and we compare the values to experimental data obtained in recent campaigns. We give estimations of the tire service life as a function of the tread wear UTQG (100 times the indicated tread wear rating). We also discuss the projected service life using tread depth reduction and mass loss.


  • Open Access

    Alternative Analyzers for the Measurement of Gaseous Compounds During Type-Approval of Heavy-Duty Vehicles

    by Ricardo Suarez-Bertoa, Roberto Gioria, Christian Ferrarese, Lorenzo Finocchiaro, Barouch Giechaskiel

    Emissions standards describe the fuels, the procedures, and, among others, the analyzers to be used for the measurement of the different compounds during the type-approval of heavy-duty engines and vehicles. Traditionally, NOx, CO, hydrocarbons, and CO2 were the gaseous compounds measured within the Euro standard, with the later addition of CH4 and NH3. Euro 7, introduced in early 2024, expanded those compounds, requiring the measurement of N2O and HCHO. With an increasing number of molecules that need to be measured and introducing carbonless fuels, such as hydrogen, that present different requirements compared to carbon-based fuels, the test procedure needs to be updated. The performances of three laboratory-grade instruments and three portable emissions measurement systems based on Fourier-transformed infrared (FTIR) or quantum cascade laser infrared (QCL-IR) technologies were investigated while measuring from the tailpipe of a Diesel engine and a compressed natural gas (CNG) vehicle. All instruments presented good agreement when emissions of NOx, CO, CH4, NH3, N2O, HCHO, and CO2 were compared using: Z-score, F-test and two tail t-test of student. Water concentration measured by the four FTIRs was also in good agreement. Moreover, the dry emissions of CO2 and CO measured by the laboratory non-dispersive infrared (NDIR) and corrected using water were a few percentages different from those obtained using the regulated carbon-based approach. The results indicate that all the investigated systems are suitable for the measurement of the investigated gaseous compounds, including CO2 and H2O.

  • Open Access

    Assessment of a NOx Measurement Procedure for Periodic Technical Inspection (PTI) of Light-Duty Diesel Vehicles

    by Jacopo Franzetti, Tommaso Selleri, Christian Ferrarese, Anastasios Melas, Dario Manara, Barouch Giechaskiel, Ricardo Suarez-Bertoa

    A Periodic Technical Inspection (PTI) of vehicles promotes road safety and environmental protection. Indeed, a PTI is also used to verify the proper functioning of the vehicle’s aftertreatment system (ATS) over its lifetime. While the current Directive 2014/45/EU, which covers the PTI, does not require a NOx emissions measurement, the ongoing revision of the roadworthiness package aims at including new methods for measuring exhaust NOx and particle number (PN) emissions. PTI tests are required to be simple, quick, inexpensive and effective. In this study, a new methodology for a NOx measurement during the PTIs of Diesel vehicles equipped with a selective catalytic reduction (SCR) unit is assed. Seven Euro 6 light-duty Diesel vehicles fulfilling post-Real Driving Emissions (RDE) regulations were tested. The NOx-PTI methodology consists of measuring NOx emissions from the vehicle tailpipe at engine low idle speed after properly conditioning the vehicle ATS. In such conditions, a well-functioning SCR unit reduced NOx emissions and the methodology proved to be suitable to discriminate between functioning and malfunctioning SCR systems.


  • Open Access

    Real-Time Measurement of NOx Emissions from Modern Diesel Vehicles Using On-Board Sensors

    by Tommaso Selleri, Christian Ferrarese, Jacopo Franzetti, Ricardo Suarez-Bertoa, Dario Manara

    In this work, the performance of on-board vehicle exhaust emission sensors is investigated and compared to reference laboratory and on-road instrumentation for two modern diesel light-duty commercial vehicles, type-approved as Euro 6d-TEMP-EVAP-ISC and Euro 6d-ISC-FCM. The first step of the analysis was to perform emissions tests in the laboratory and compare the NOx concentrations registered by the vehicle sensors available at the engine-out and tailpipe positions with those recorded by reference laboratory instrumentation. In a second step, tests were also conducted on road, comparing the performance of on-board sensors with those of Portable Emission Measurement System (PEMS) analysers, which were taken as references. The uncertainty related to exhaust flow measurements was also addressed. In particular, emissions factors calculated using the flow rates measured either in the laboratory or on-road were compared to those obtained by computing exhaust flows with on-board recorded data available from the vehicle electronic control unit. Results showed maximum deviations on the order of 34% in laboratory tests and of 21% during on-road measurements. Finally, measurements were also carried out during a diesel particulate filter regeneration event, showing the good performance of the on-board sensors even when high NOx concentrations were present. These conditions can be similar to those experienced in the case of an after-treatment system malfunction or of a high-emitting event, and can thus be of interest for real-time malfunction identification and monitoring.


  • Open Access

    Real-Time Measurements of Formaldehyde Emissions from Modern Vehicles

    by Ricardo Suarez-Bertoa, Tommaso Selleri, Roberto Gioria, Anastasios D. Melas, Christian Ferrarese, Jacopo Franzetti, Bertold Arlitt, Naoki Nagura, Takaaki Hanada, Barouch Giechaskiel

    Formaldehyde (HCHO), a carcinogenic carbonyl compound and precursor of tropospheric ozone, can be found in vehicle exhaust. Even though the continuous monitoring of HCHO has been recommended, the real-world emissions from the road transport sector are not commonly available. The main reason for this knowledge gap has been the difficulty to measure HCHO in real-time and during real-world testing. This, for instance, increases the uncertainty of the O3 simulated by air quality models. The present study investigates real-time HCHO measurements comparing three Fourier Transform InfraRed spectrometers (FTIRs) and one Quantum Cascade Laser InfraRed spectrometer (QCL-IR) directly sampling from the exhaust of one gasoline passenger car, one Diesel commercial vehicle and one Diesel heavy-duty vehicle, all meeting recent European emission standards (Euro 6/VI). Non-negligible emissions of HCHO were measured from the Diesel light-duty vehicle, with emissions increasing as temperature decreased. Relatively low emissions were measured for the gasoline car and the Diesel heavy-duty vehicle. The results showed a good correlation between the different instruments under all the conditions tested (in most cases R2 > 0.9). Moreover, it was shown that HCHO can be accurately measured during on-road and real-world-like tests using instruments based on FTIR and QCL-IR technologies.


  • Open Access

    Assessment of a Euro VI Step E Heavy-Duty Vehicle’s Aftertreatment System

    by Barouch Giechaskiel, Tommaso Selleri, Roberto Gioria, Anastasios D. Melas, Jacopo Franzetti, Christian Ferrarese, Ricardo Suarez-Bertoa

    The latest generation of heavy-duty vehicles (Euro VI step E) have to respect low emission limits both in the laboratory and on the road. The most challenging pollutants for diesel vehicles are NOx and particles; nevertheless, NH3 and N2O need attention. In this study, we measured regulated and unregulated pollutants of a Euro VI step E Diesel vehicle. Samples were taken downstream of (i) the engine, (ii) the Diesel oxidation catalyst (DOC) and catalyzed Diesel particulate filter (cDPF), and (iii) the selective catalytic reduction (SCR) unit for NOx with an ammonia slip catalyst (ASC). In addition to typical laboratory and real-world cycles, various challenging tests were conducted (urban driving with low payload, high-speed full-load driving, and idling) at 23 °C and 5 °C. The results showed high efficiencies of the DOC, DPF, and SCR under most testing conditions. Cold start cycles resulted in high NOx emissions, while high-temperature cycles resulted in high particle emissions. The main message of this study is that further improvements are necessary, also considering possible reductions in the emission limits in future EU regulations.


  • Open Access

    Emissions from a Modern Euro 6d Diesel Plug-In Hybrid

    by Tommaso Selleri, Anastasios Melas, Christian Ferrarese, Jacopo Franzetti, Barouch Giechaskiel, Ricardo Suarez-Bertoa

    Plug-in hybrid electric vehicles (PHEVs) are promoted as an alternative to conventional vehicles to meet European decarbonisation and air quality targets. However, several studies have shown that gasoline PHEVs present similar criteria and particulate emissions as their conventional gasoline counterparts. In the present work, we investigate the environmental performance of a modern plug-in hybrid Diesel-fuelled vehicle meeting the Euro 6d standard under a large variety of driving patterns, ambient temperatures, and battery states of charge (SOC). Emissions of regulated pollutants, currently unregulated pollutants, and CO2 were measured in the laboratory and following various on-road routes. The vehicle, whose electric range was 82 km, presented emissions below the Euro 6 regulatory limits in all the different driving cycles performed at 23 °C and all the on-road tests at the different battery SOC. The emissions were lower than the average of the conventional Diesel vehicles tested at JRC in 2020–2021 for all the SOC tested, the exception being solid particle number emissions >23 nm (SPN23) emissions that were comparable at all SOC. Moreover, the emissions obtained with the high voltage battery fully charged during on-road tests were comparable to those obtained with the battery at the minimum SOC for the entire test (ca. 91 km) as well as for the urban section (ca. 36 km). Overall, NOx and SPN23 emissions increased at lower temperatures, showing that at very low temperatures, there is no benefit in terms of particulate emissions from the electric range. Finally, it is shown that the emissions of N2O, the only unregulated pollutant presenting relevant emissions for this vehicle, and which are of catalytic nature, were proportional to the utilisation of the internal combustion engine. The scope of the manuscript is thus to deepen the knowledge on the emission performances of Diesel PHEVs through the systematic testing of a modern representative of this class of vehicles in a wide range of driving and environmental conditions.