Yumeng Cai
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Research Interests
Yumeng Cai has a total of 55 co-authors. Here are the top co-authors by number of shared publications:
- Peng Sun
North China Electric Power University
12 shared publications - Zhibin Zhao
State Key Laboratory of Alternate Electrical Power System with Renewable Energy Sources, North China Electric Power University, Beijing 102206, China
11 shared publications - Xuebao Li
North China Electric Power University
8 shared publications Zhibin Zhao
North China Electric Power University
5 shared publications- Zhong Chen
Department of Electrical Engineering, University of Arkansas, Fayetteville, AR 72701, USA
4 shared publications - Bin Zhao
State Key Laboratory of Alternate Electrical Power System with Renewable Energy Sources, North China Electric Power University, Beijing, China
3 shared publications
Latest Publications
- 1 November 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Electron Devices
- Vol. 73 (11) , 6526-6532
Revisiting Temperature Dependence of d I C /d t and d V CE /d t for Field-Stop IGBTs Under Capacitor-Assisted Soft-Switching Turn-Off
- 1 November 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Electron Devices
- Vol. 73 (11) , 6526-6532
Revisiting Temperature Dependence of d I C /d t and d V CE /d t for Field-Stop IGBTs Under Capacitor-Assisted Soft-Switching Turn-Off
- 1 November 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Power Electronics
- Vol. 41 (11) , 18990-18999
Online Junction Temperature Monitoring Method for Paralleled SiC MOSFETs With the Discrete Gate Drive Control
To meet higher power demands, multiple SiC MOSFET chips are often connected in parallel. However, non-uniform junction temperature distribution among these paralleled devices has emerged as a critical challenge, significantly impacting system reliability and lifetime. Despite various thermal management efforts, existing techniques lack an accurate, real-time method to monitor individual chip junction temperatures in paralleled configurations. In this article, a junction temperature monitoring method for paralleled SiC MOSFETs with discrete gate drive (DGD) control is proposed. And a PCB Rogowski coil is settled on the confluence of paralleled branches to capture dynamic current characteristics. By actively adjusting the turn-on delay among SiC MOSFETs, the junction temperature can be extracted by leveraging the temperature dependence of quasi-threshold voltage (Vth-qua) during a gate delay interval without intrusive sensing. Comprehensive analysis is conducted to evaluate the impact of device temperature imbalance and varying operating conditions on measurement accuracy. The proposed method is finally applied and verified online in a buck experiment platform to sensing junction temperature of paralleled SiC MOSFETs. Under three distinct uneven cooling scenarios, the maximum monitoring error is limited to just 2.9 °C, confirming the method's high accuracy and robustness. This work offers a practical and scalable approach for junction temperature monitoring in paralleled SiC MOSFETs, paving the way for more reliable thermal design and intelligent health monitoring in high-power, safety-critical applications.
- 1 November 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Power Electronics
- Vol. 41 (11) , 18990-18999
Online Junction Temperature Monitoring Method for Paralleled SiC MOSFETs With the Discrete Gate Drive Control
To meet higher power demands, multiple SiC MOSFET chips are often connected in parallel. However, non-uniform junction temperature distribution among these paralleled devices has emerged as a critical challenge, significantly impacting system reliability and lifetime. Despite various thermal management efforts, existing techniques lack an accurate, real-time method to monitor individual chip junction temperatures in paralleled configurations. In this article, a junction temperature monitoring method for paralleled SiC MOSFETs with discrete gate drive (DGD) control is proposed. And a PCB Rogowski coil is settled on the confluence of paralleled branches to capture dynamic current characteristics. By actively adjusting the turn-on delay among SiC MOSFETs, the junction temperature can be extracted by leveraging the temperature dependence of quasi-threshold voltage (Vth-qua) during a gate delay interval without intrusive sensing. Comprehensive analysis is conducted to evaluate the impact of device temperature imbalance and varying operating conditions on measurement accuracy. The proposed method is finally applied and verified online in a buck experiment platform to sensing junction temperature of paralleled SiC MOSFETs. Under three distinct uneven cooling scenarios, the maximum monitoring error is limited to just 2.9 °C, confirming the method's high accuracy and robustness. This work offers a practical and scalable approach for junction temperature monitoring in paralleled SiC MOSFETs, paving the way for more reliable thermal design and intelligent health monitoring in high-power, safety-critical applications.
- 3 February 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Dielectrics and Electrical Insulation
- Vol. 33 (3) , 1622-1629
Bubble Degassing Characteristics in Silicone Gel and Improved Degassing Process to Enhance Its Insulation Capacity
Silicone gel is widely used in the packaging of high-voltage power devices because of its sealing, high temperature resistance and good insulation performance. However, the residual bubbles of silicone gel in the process of encapsulation are very easy to produce partial discharge or even breakdown phenomenon, which seriously restricts insulation reliability of high voltage power devices. To this end, the bubble motion in silicone gel during degassing is investigated to guide process optimization and enhance insulation performance in this paper. Firstly, by simulation and experiment, the influence of viscosity of silicone gel and different degassing pressure conditions on rising velocity of the bubble with initial bubble diameter are obtained. Then, the influence of thickness of silicone gel on the bubble rising velocity rate is also investigated. Furthermore, an optimized repeated degassing curve and stratified degassing method are proposed. The experimental results show that the breakdown voltage of the silicone gel treated by the repeated pressure buck process method increased by 16.84% compared with original process. Moreover, the insulation capability of silicone gel made by stratified degassing method is at least increased by 5.8%. Overall, methods proposed in this paper provide guidance for the advanced preparation process of silicone gel to promote insulation capability of IGBT device encapsulation.
- 3 February 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Dielectrics and Electrical Insulation
- Vol. 33 (3) , 1622-1629
Bubble Degassing Characteristics in Silicone Gel and Improved Degassing Process to Enhance Its Insulation Capacity
Silicone gel is widely used in the packaging of high-voltage power devices because of its sealing, high temperature resistance and good insulation performance. However, the residual bubbles of silicone gel in the process of encapsulation are very easy to produce partial discharge or even breakdown phenomenon, which seriously restricts insulation reliability of high voltage power devices. To this end, the bubble motion in silicone gel during degassing is investigated to guide process optimization and enhance insulation performance in this paper. Firstly, by simulation and experiment, the influence of viscosity of silicone gel and different degassing pressure conditions on rising velocity of the bubble with initial bubble diameter are obtained. Then, the influence of thickness of silicone gel on the bubble rising velocity rate is also investigated. Furthermore, an optimized repeated degassing curve and stratified degassing method are proposed. The experimental results show that the breakdown voltage of the silicone gel treated by the repeated pressure buck process method increased by 16.84% compared with original process. Moreover, the insulation capability of silicone gel made by stratified degassing method is at least increased by 5.8%. Overall, methods proposed in this paper provide guidance for the advanced preparation process of silicone gel to promote insulation capability of IGBT device encapsulation.
- Open Access
- 1 January 2026
- Published by Institution of Engineering and Technology (IET) in IET Power Electronics
- Vol. 19 (1)
Active Gate Circuit for Mitigating Gate Voltage Oscillations during Short Circuit of High Power IGBT
The high‐frequency gate voltage oscillations occurring under short‐circuit (SC) conditions in high‐power insulated‐gate bipolar transistors pose a serious challenge to device reliability. However, existing oscillation suppression methods cannot effectively mitigate gate oscillation during SC without affecting the normal operation of the device. This paper proposes an active gate circuit for mitigating gate oscillation (GOM‐AGC), which consists of a gate overvoltage detection circuit, an equivalent operational transconductance amplifier regulator unit and a dynamic energy release circuit. The closed‐loop operating principle of the proposed circuit is introduced and the circuit delay time is analysed and illustrated through simulation. Furthermore, SC experiments are conducted on a commercial 1.7 kV/3.6 kA IGBT power module to verify the effectiveness of the proposed circuit. The results indicate that the proposed GOM‐AGC can significantly mitigate gate oscillations with a delay of a few hundred nanoseconds, while ensuring device operating performance. At a bus voltage of 700 V, the peak gate voltage is reduced from 90 to 32.4 V. At 800 V, it is decreased from 69.2 to 26 V. Additionally, the proposed circuit can also improve the gate voltage waveform under higher gate resistance. The work presented in this paper has significant application value for improving the SC reliability of high‐power IGBTs.
- 1 January 2026
- Published by Institution of Engineering and Technology (IET) in IET Power Electronics
- Vol. 19 (1)
Open AccessActive Gate Circuit for Mitigating Gate Voltage Oscillations during Short Circuit of High Power IGBT
The high‐frequency gate voltage oscillations occurring under short‐circuit (SC) conditions in high‐power insulated‐gate bipolar transistors pose a serious challenge to device reliability. However, existing oscillation suppression methods cannot effectively mitigate gate oscillation during SC without affecting the normal operation of the device. This paper proposes an active gate circuit for mitigating gate oscillation (GOM‐AGC), which consists of a gate overvoltage detection circuit, an equivalent operational transconductance amplifier regulator unit and a dynamic energy release circuit. The closed‐loop operating principle of the proposed circuit is introduced and the circuit delay time is analysed and illustrated through simulation. Furthermore, SC experiments are conducted on a commercial 1.7 kV/3.6 kA IGBT power module to verify the effectiveness of the proposed circuit. The results indicate that the proposed GOM‐AGC can significantly mitigate gate oscillations with a delay of a few hundred nanoseconds, while ensuring device operating performance. At a bus voltage of 700 V, the peak gate voltage is reduced from 90 to 32.4 V. At 800 V, it is decreased from 69.2 to 26 V. Additionally, the proposed circuit can also improve the gate voltage waveform under higher gate resistance. The work presented in this paper has significant application value for improving the SC reliability of high‐power IGBTs.
- Open Access
- 1 January 2026
- Published by Institution of Engineering and Technology (IET) in IET Power Electronics
- Vol. 19 (1) , e70307
Droop and Offset Error Suppression Method for a PCB Self‐Integrating Rogowski Coil Sensor
To meet the stringent requirements for high bandwidth and low error in current sensors used for condition monitoring of power converters, embedded printed circuit board (PCB) Rogowski coil sensors have become a promising solution. However, existing PCB Rogowski coil sensors exhibit inherent droop and offset errors when monitoring the switching currents of power converters. To address this issue, this paper proposes a droop and offset error suppression method for a PCB self‐integrating Rogowski coil sensor. By optimising the parameters of the self‐integrating integrator circuit, the proposed method mitigates waveform distortion in silicon carbide (SiC) MOSFET pulse‐current monitoring with conventional sensors. Experimental results show that the method reduces the droop rate of a 50 µs pulse to 3.9%, satisfying the requirement of less than 5%, and limits the offset voltage to within 5 V. The improved measurement accuracy enables abnormal states such as short circuit and overheating to be reflected more accurately, providing accurate current information for reliability‐oriented condition monitoring of power converters.
- 1 January 2026
- Published by Institution of Engineering and Technology (IET) in IET Power Electronics
- Vol. 19 (1) , e70307
Open AccessDroop and Offset Error Suppression Method for a PCB Self‐Integrating Rogowski Coil Sensor
To meet the stringent requirements for high bandwidth and low error in current sensors used for condition monitoring of power converters, embedded printed circuit board (PCB) Rogowski coil sensors have become a promising solution. However, existing PCB Rogowski coil sensors exhibit inherent droop and offset errors when monitoring the switching currents of power converters. To address this issue, this paper proposes a droop and offset error suppression method for a PCB self‐integrating Rogowski coil sensor. By optimising the parameters of the self‐integrating integrator circuit, the proposed method mitigates waveform distortion in silicon carbide (SiC) MOSFET pulse‐current monitoring with conventional sensors. Experimental results show that the method reduces the droop rate of a 50 µs pulse to 3.9%, satisfying the requirement of less than 5%, and limits the offset voltage to within 5 V. The improved measurement accuracy enables abnormal states such as short circuit and overheating to be reflected more accurately, providing accurate current information for reliability‐oriented condition monitoring of power converters.
- Open Access
- 1 January 2026
- Published by Institution of Engineering and Technology (IET) in IET Power Electronics
- Vol. 19 (1)
A Dynamic Diagnosis Method for Separating Bond‐Wires Fatigue and Gate Oxide Degradation of SiC MOSFETs
Bond‐wire fatigue and gate oxide degradation are the main reliability issues for silicon carbide (SiC) MOSFETs. Accurately separating these two degradation modes and identifying the dominant failure mechanism in operation is crucial for improving device reliability. In this paper, a dynamic diagnosis method for separating bond‐wire‐fatigue and gate oxide degradation in SiC MOSFETs is proposed. A switching transient analytical model considering bond‐wires related parasitic parameters is established first. The analytical analysis reveals that the drain current slope during the turn‐on process can comprehensively characterise both bond wires and gate oxide degradation. Furthermore, numerical analysis is conducted to quantitatively investigate the dependence of the drain current slope on bond‐wire fatigue and gate oxide degradation. It is found that the relative change in drain current slope induced by bond‐wire fatigue decreases with increasing gate resistance, whereas that caused by gate oxide degradation decreases with increasing gate voltage. Based on this observation, a dynamic diagnostic method is proposed to separate the two degradation modes by obtaining the drain current slope under different driving parameters. Finally, equivalent degradation experiments are carried out to validate the proposed dynamic diagnosis method. This work provides a foundation for reliability monitoring and control of SiC MOSFETs in actual switching operation.
- 1 January 2026
- Published by Institution of Engineering and Technology (IET) in IET Power Electronics
- Vol. 19 (1)
Open AccessA Dynamic Diagnosis Method for Separating Bond‐Wires Fatigue and Gate Oxide Degradation of SiC MOSFETs
Bond‐wire fatigue and gate oxide degradation are the main reliability issues for silicon carbide (SiC) MOSFETs. Accurately separating these two degradation modes and identifying the dominant failure mechanism in operation is crucial for improving device reliability. In this paper, a dynamic diagnosis method for separating bond‐wire‐fatigue and gate oxide degradation in SiC MOSFETs is proposed. A switching transient analytical model considering bond‐wires related parasitic parameters is established first. The analytical analysis reveals that the drain current slope during the turn‐on process can comprehensively characterise both bond wires and gate oxide degradation. Furthermore, numerical analysis is conducted to quantitatively investigate the dependence of the drain current slope on bond‐wire fatigue and gate oxide degradation. It is found that the relative change in drain current slope induced by bond‐wire fatigue decreases with increasing gate resistance, whereas that caused by gate oxide degradation decreases with increasing gate voltage. Based on this observation, a dynamic diagnostic method is proposed to separate the two degradation modes by obtaining the drain current slope under different driving parameters. Finally, equivalent degradation experiments are carried out to validate the proposed dynamic diagnosis method. This work provides a foundation for reliability monitoring and control of SiC MOSFETs in actual switching operation.
- Open Access
- 1 January 2026
- Published by Institution of Engineering and Technology (IET) in IET Power Electronics
- Vol. 19 (1)
An Accurate On‐State Voltage Measurement Circuit for Chip‐Level Junction Temperature Monitoring of Press‐Pack IGBT
Junction temperature monitoring for multiple chips inside a press‐pack insulated gate bipolar transistor (PP IGBT) is essential to evaluate the temperature uniformity and operational reliability of the device. The low‐current collector–emitter on‐state voltage ( V ce ) is the most promising method for chip‐level junction temperature monitoring owing to its high measurement accuracy. However, for conventional on‐state voltage measurement circuits (OVMCs), the temperature difference occurs between the dual diodes during long‐term operation, leading to errors in the online V ce measurement. This paper proposes a novel OVMC for accurately extracting V ce online. By adopting a power‐balanced differential diode topology, the temperature of the dual diodes is equalised, thereby minimising the error of V ce measurement. Comparative experiments with the conventional circuits indicate that the proposed OVMC reduces the temperature difference between the dual diodes from approximately 5°C in the conventional circuits to 0.3°C, and the maximum V ce measurement error is within 1 mV. Furthermore, the proposed circuit is applied to the Buck operating condition to monitor the junction temperature of chips inside the PP IGBT. The maximum temperature monitoring error is only 2.0°C compared with that of the contact thermocouple measurements, demonstrating the accuracy of the proposed OVMC for online junction temperature monitoring.
- 1 January 2026
- Published by Institution of Engineering and Technology (IET) in IET Power Electronics
- Vol. 19 (1)
Open AccessAn Accurate On‐State Voltage Measurement Circuit for Chip‐Level Junction Temperature Monitoring of Press‐Pack IGBT
Junction temperature monitoring for multiple chips inside a press‐pack insulated gate bipolar transistor (PP IGBT) is essential to evaluate the temperature uniformity and operational reliability of the device. The low‐current collector–emitter on‐state voltage ( V ce ) is the most promising method for chip‐level junction temperature monitoring owing to its high measurement accuracy. However, for conventional on‐state voltage measurement circuits (OVMCs), the temperature difference occurs between the dual diodes during long‐term operation, leading to errors in the online V ce measurement. This paper proposes a novel OVMC for accurately extracting V ce online. By adopting a power‐balanced differential diode topology, the temperature of the dual diodes is equalised, thereby minimising the error of V ce measurement. Comparative experiments with the conventional circuits indicate that the proposed OVMC reduces the temperature difference between the dual diodes from approximately 5°C in the conventional circuits to 0.3°C, and the maximum V ce measurement error is within 1 mV. Furthermore, the proposed circuit is applied to the Buck operating condition to monitor the junction temperature of chips inside the PP IGBT. The maximum temperature monitoring error is only 2.0°C compared with that of the contact thermocouple measurements, demonstrating the accuracy of the proposed OVMC for online junction temperature monitoring.
- 21 November 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Dielectrics and Electrical Insulation
- Vol. PP (10709878) , 1
Space Charge Characteristic of Silicone Elastomer Used in SiC Device under High Temperature up to 200°C
In order to study the space charge characteristics of silicone elastomers at high temperatures, a high-temperature PEA space charge characteristic measurement system with a temperature range of room temperature (25°C)-200°C was developed in this paper. The system developed in this paper can meet the temperature control and measurement requirements through actual temperature measurement and calibration. Through this system, this paper studies the space charge characteristics and short-circuit characteristics of silicone elastomers under different polarity DC voltages in the range of 25°C-200°C. With the increase of temperature, the charge accumulation depth first increases and then decreases, and the charge accumulation amount first increases and then decreases. The migration rate of negative polarity charges is greater than that of positive polarity charges. The trap characteristics of silicone elastomers at different temperatures are analyzed by charge dissipation characteristics. At lower temperatures, the deep trap density is greater than the shallow trap density, whether it is electron traps or hole traps. When it is greater than a certain temperature, the shallow trap density is greater than the deep trap density. Temperature affects charge generation and charge migration. At low temperatures, the charge injection amount increases and becomes the dominant factor. When the temperature increases, the charge mobility increases and becomes the dominant factor, so the charge accumulation amount and trap density both increase and then decrease with temperature.
- 21 November 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Dielectrics and Electrical Insulation
- Vol. PP (10709878) , 1
Space Charge Characteristic of Silicone Elastomer Used in SiC Device under High Temperature up to 200°C
In order to study the space charge characteristics of silicone elastomers at high temperatures, a high-temperature PEA space charge characteristic measurement system with a temperature range of room temperature (25°C)-200°C was developed in this paper. The system developed in this paper can meet the temperature control and measurement requirements through actual temperature measurement and calibration. Through this system, this paper studies the space charge characteristics and short-circuit characteristics of silicone elastomers under different polarity DC voltages in the range of 25°C-200°C. With the increase of temperature, the charge accumulation depth first increases and then decreases, and the charge accumulation amount first increases and then decreases. The migration rate of negative polarity charges is greater than that of positive polarity charges. The trap characteristics of silicone elastomers at different temperatures are analyzed by charge dissipation characteristics. At lower temperatures, the deep trap density is greater than the shallow trap density, whether it is electron traps or hole traps. When it is greater than a certain temperature, the shallow trap density is greater than the deep trap density. Temperature affects charge generation and charge migration. At low temperatures, the charge injection amount increases and becomes the dominant factor. When the temperature increases, the charge mobility increases and becomes the dominant factor, so the charge accumulation amount and trap density both increase and then decrease with temperature.
- 5 December 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Device and Materials Reliability
- Vol. PP (15304388) , 1
Influence of Short-Circuit Time on Short-Circuit Failure Modes of Planar Silicon Carbide MOSFETs
The short-circuit (SC) capability of silicon carbide (SiC) MOSFETs is weaker than that of silicon (Si) devices. Gate failure and thermal runaway failure are two typical SC failure modes and both failure mechanisms are related to temperature. In practical application, affected by SC protection action time, devices may fail during conduction or after turn-off, and it is of vital significance to investigate the impact of SC time (tsc) on failure modes. In this paper, a SC failure experimental platform is built. The failure modes of planar SiC MOSFETs from different manufactures under limited and unlimited tsc are investigated and divided more detailed. Results indicate that there are multiple failure modes for failures after turn-off affecting by limited tsc, while the devices from different manufactures have different SC failure modes during SC conduction period when tsc is unlimited. In addition, the characteristics of failures are more complex for planar SiC MOSFETs with negative off-state gate voltage. Moreover, the behavior of electrical quantities under different operating conditions is analyzed and the relationship between SC failure modes with different tsc is revealed with an improved Cauer thermal model. It is verified that tsc has an influence on the SC failure modes of planar SiC MOSFETs.
- 5 December 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Device and Materials Reliability
- Vol. PP (15304388) , 1
Influence of Short-Circuit Time on Short-Circuit Failure Modes of Planar Silicon Carbide MOSFETs
The short-circuit (SC) capability of silicon carbide (SiC) MOSFETs is weaker than that of silicon (Si) devices. Gate failure and thermal runaway failure are two typical SC failure modes and both failure mechanisms are related to temperature. In practical application, affected by SC protection action time, devices may fail during conduction or after turn-off, and it is of vital significance to investigate the impact of SC time (tsc) on failure modes. In this paper, a SC failure experimental platform is built. The failure modes of planar SiC MOSFETs from different manufactures under limited and unlimited tsc are investigated and divided more detailed. Results indicate that there are multiple failure modes for failures after turn-off affecting by limited tsc, while the devices from different manufactures have different SC failure modes during SC conduction period when tsc is unlimited. In addition, the characteristics of failures are more complex for planar SiC MOSFETs with negative off-state gate voltage. Moreover, the behavior of electrical quantities under different operating conditions is analyzed and the relationship between SC failure modes with different tsc is revealed with an improved Cauer thermal model. It is verified that tsc has an influence on the SC failure modes of planar SiC MOSFETs.