Xuebao Li
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Xuebao Li has a total of 155 co-authors. Here are the top co-authors by number of shared publications:
- Xiang Cui
State Key Laboratory of Alternate Electrical Power System with Renewable Energy Sources, North China Electrical Power University, Beijing, China
36 shared publications - Zhibin Zhao
State Key Laboratory of Alternate Electrical Power System with Renewable Energy Sources, North China Electric Power University, Beijing 102206, China
31 shared publications - Lei Qi
North China Electric Power University
11 shared publications - Peng Sun
North China Electric Power University
11 shared publications Zhibin Zhao
North China Electric Power University
10 shared publicationsTiebing Lu
Beijing Key Laboratory of High Voltage and EMC, North China Electric Power University Beijing 102206 People's Republic of China
8 shared publications
Latest Publications
- 1 November 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Electron Devices
- Vol. 73  (11) , 6526-6532
Revisiting Temperature Dependence of d I C /d t and d V CE /d t for Field-Stop IGBTs Under Capacitor-Assisted Soft-Switching Turn-Off
- 1 November 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Electron Devices
- Vol. 73  (11) , 6526-6532
Revisiting Temperature Dependence of d I C /d t and d V CE /d t for Field-Stop IGBTs Under Capacitor-Assisted Soft-Switching Turn-Off
- 1 November 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Power Electronics
- Vol. 41  (11) , 18990-18999
Online Junction Temperature Monitoring Method for Paralleled SiC MOSFETs With the Discrete Gate Drive Control
To meet higher power demands, multiple SiC MOSFET chips are often connected in parallel. However, non-uniform junction temperature distribution among these paralleled devices has emerged as a critical challenge, significantly impacting system reliability and lifetime. Despite various thermal management efforts, existing techniques lack an accurate, real-time method to monitor individual chip junction temperatures in paralleled configurations. In this article, a junction temperature monitoring method for paralleled SiC MOSFETs with discrete gate drive (DGD) control is proposed. And a PCB Rogowski coil is settled on the confluence of paralleled branches to capture dynamic current characteristics. By actively adjusting the turn-on delay among SiC MOSFETs, the junction temperature can be extracted by leveraging the temperature dependence of quasi-threshold voltage (Vth-qua) during a gate delay interval without intrusive sensing. Comprehensive analysis is conducted to evaluate the impact of device temperature imbalance and varying operating conditions on measurement accuracy. The proposed method is finally applied and verified online in a buck experiment platform to sensing junction temperature of paralleled SiC MOSFETs. Under three distinct uneven cooling scenarios, the maximum monitoring error is limited to just 2.9 °C, confirming the method's high accuracy and robustness. This work offers a practical and scalable approach for junction temperature monitoring in paralleled SiC MOSFETs, paving the way for more reliable thermal design and intelligent health monitoring in high-power, safety-critical applications.
- 1 November 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Power Electronics
- Vol. 41  (11) , 18990-18999
Online Junction Temperature Monitoring Method for Paralleled SiC MOSFETs With the Discrete Gate Drive Control
To meet higher power demands, multiple SiC MOSFET chips are often connected in parallel. However, non-uniform junction temperature distribution among these paralleled devices has emerged as a critical challenge, significantly impacting system reliability and lifetime. Despite various thermal management efforts, existing techniques lack an accurate, real-time method to monitor individual chip junction temperatures in paralleled configurations. In this article, a junction temperature monitoring method for paralleled SiC MOSFETs with discrete gate drive (DGD) control is proposed. And a PCB Rogowski coil is settled on the confluence of paralleled branches to capture dynamic current characteristics. By actively adjusting the turn-on delay among SiC MOSFETs, the junction temperature can be extracted by leveraging the temperature dependence of quasi-threshold voltage (Vth-qua) during a gate delay interval without intrusive sensing. Comprehensive analysis is conducted to evaluate the impact of device temperature imbalance and varying operating conditions on measurement accuracy. The proposed method is finally applied and verified online in a buck experiment platform to sensing junction temperature of paralleled SiC MOSFETs. Under three distinct uneven cooling scenarios, the maximum monitoring error is limited to just 2.9 °C, confirming the method's high accuracy and robustness. This work offers a practical and scalable approach for junction temperature monitoring in paralleled SiC MOSFETs, paving the way for more reliable thermal design and intelligent health monitoring in high-power, safety-critical applications.
- 12 March 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Plasma Science
- Vol. 54  (4) , 1569-1579
Design and Implementation of a High-Frequency Bipolar Square-Wave Pulse Generator With Full Duty Cycle Control and Nanosecond-Rise Time
To study the partial discharge (PD) of packaging materials for high-voltage silicon carbide devices under conditions of high d $v$ /d $t$ and wide duty cycle, a nanosecond-level high-repetition-rate, full-duty-cycle bipolar square-wave pulse power supply suitable for the research on packaging insulation properties was designed and developed. This power supply forms a bipolar square-wave output through the cascading of multilevel submodules combined with a symmetric positive–negative voltage division structure, and adopts a folded output loop to significantly reduce parasitic inductance. Experimental results show that when the maximum output peak-to-peak value is 10 kV and the repetition frequency reaches 45 kHz, the rise time of the square-wave pulse can be stably maintained at approximately 18 ns, the fall time is about 23 ns, and the duty cycle can be flexibly adjusted within the range of 0%–100%. Based on strict mathematical derivation, the coupling relationship between dead time, repetition frequency, and duty cycle is clarified, and the driving and power supply schemes are optimized accordingly. Compared with existing test power supplies, this system has achieved significant breakthroughs in fast rising edge, high repetition frequency, and full-duty-cycle control, providing a reliable experimental basis for in-depth revelation of the failure mechanism of packaging insulation materials in silicon carbide high-voltage power modules.
- 12 March 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Plasma Science
- Vol. 54  (4) , 1569-1579
Design and Implementation of a High-Frequency Bipolar Square-Wave Pulse Generator With Full Duty Cycle Control and Nanosecond-Rise Time
To study the partial discharge (PD) of packaging materials for high-voltage silicon carbide devices under conditions of high d $v$ /d $t$ and wide duty cycle, a nanosecond-level high-repetition-rate, full-duty-cycle bipolar square-wave pulse power supply suitable for the research on packaging insulation properties was designed and developed. This power supply forms a bipolar square-wave output through the cascading of multilevel submodules combined with a symmetric positive–negative voltage division structure, and adopts a folded output loop to significantly reduce parasitic inductance. Experimental results show that when the maximum output peak-to-peak value is 10 kV and the repetition frequency reaches 45 kHz, the rise time of the square-wave pulse can be stably maintained at approximately 18 ns, the fall time is about 23 ns, and the duty cycle can be flexibly adjusted within the range of 0%–100%. Based on strict mathematical derivation, the coupling relationship between dead time, repetition frequency, and duty cycle is clarified, and the driving and power supply schemes are optimized accordingly. Compared with existing test power supplies, this system has achieved significant breakthroughs in fast rising edge, high repetition frequency, and full-duty-cycle control, providing a reliable experimental basis for in-depth revelation of the failure mechanism of packaging insulation materials in silicon carbide high-voltage power modules.
- 3 March 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Power Electronics
- Vol. 41  (9) , 14596-14613
Mechanism Analysis of Pressure Impacts on Turn-Off Transient Process in Single Press-Pack IGBT Chip
For press-pack insulated gate bipolar transistors (PPIs), an external clamping force is applied to ensure adequate electrical contact between multilayers. The resulting pressure field significantly influences the chip's turn-off capability and is attracting increasing attention. In this article, the pressure effects on the overall turn-off transient of a PPI chip are investigated comprehensively through theoretical analysis, experimental measurements, and semiconductor simulations. Under high-voltage/high-current conditions, as pressure non-uniformity increases, dynamic avalanche and the ensuing current filaments are triggered earlier and persist longer, increasing the risk of failure. In non-destructive experiments, the pressure non-uniformity on the chip is increased stepwise by raising the clamping force. Around the nominal clamping force, a 1 kN increase reduces the dynamic avalanche onset voltage by about 200 V. Two-cell simulations indicate that current filaments form following the onset of dynamic avalanche, leading to a 41% rise in the maximum current density Jmax. This increase intensifies the maximum localized electro-thermal stress and continues to grow with time. In practice, Jmax and its effects are considerably larger than suggested by the simulations, because real PPI chips comprise far more cells, which promotes stronger filament localization.
- 3 March 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Power Electronics
- Vol. 41  (9) , 14596-14613
Mechanism Analysis of Pressure Impacts on Turn-Off Transient Process in Single Press-Pack IGBT Chip
For press-pack insulated gate bipolar transistors (PPIs), an external clamping force is applied to ensure adequate electrical contact between multilayers. The resulting pressure field significantly influences the chip's turn-off capability and is attracting increasing attention. In this article, the pressure effects on the overall turn-off transient of a PPI chip are investigated comprehensively through theoretical analysis, experimental measurements, and semiconductor simulations. Under high-voltage/high-current conditions, as pressure non-uniformity increases, dynamic avalanche and the ensuing current filaments are triggered earlier and persist longer, increasing the risk of failure. In non-destructive experiments, the pressure non-uniformity on the chip is increased stepwise by raising the clamping force. Around the nominal clamping force, a 1 kN increase reduces the dynamic avalanche onset voltage by about 200 V. Two-cell simulations indicate that current filaments form following the onset of dynamic avalanche, leading to a 41% rise in the maximum current density Jmax. This increase intensifies the maximum localized electro-thermal stress and continues to grow with time. In practice, Jmax and its effects are considerably larger than suggested by the simulations, because real PPI chips comprise far more cells, which promotes stronger filament localization.
- 9 February 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Instrumentation and Measurement
- Vol. 75  (00189456) , 1-11
Low-Parasitic-Inductance Module With Interleaved Vertical PCB Layout for Dynamic Testing of SiC MOSFET Bare Die
Dynamic characterization of silicon carbide (SiC) MOSFET bare dies is essential but challenging due to their inherently fast switching speed, which makes them highly susceptible to parasitic inductance. To address this, this article proposes a dynamic test module with ultralow parasitic inductance. The design employs multiple short probes in parallel, reducing probe inductance below 2 nH and overall socket inductance to approximately 5.75 nH. An interleaved vertical PCB layout is implemented to minimize the power loop inductance through magnetic field cancellation, achieving an experimental value as low as 3.45 nH. This work first analyzes the detrimental effects of parasitic inductance to justify its minimization, then details the module design and probe characterization. A data-driven optimization method for the PCB layout is introduced. Experimental results validate the effectiveness of the proposed design.
- 9 February 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Instrumentation and Measurement
- Vol. 75  (00189456) , 1-11
Low-Parasitic-Inductance Module With Interleaved Vertical PCB Layout for Dynamic Testing of SiC MOSFET Bare Die
Dynamic characterization of silicon carbide (SiC) MOSFET bare dies is essential but challenging due to their inherently fast switching speed, which makes them highly susceptible to parasitic inductance. To address this, this article proposes a dynamic test module with ultralow parasitic inductance. The design employs multiple short probes in parallel, reducing probe inductance below 2 nH and overall socket inductance to approximately 5.75 nH. An interleaved vertical PCB layout is implemented to minimize the power loop inductance through magnetic field cancellation, achieving an experimental value as low as 3.45 nH. This work first analyzes the detrimental effects of parasitic inductance to justify its minimization, then details the module design and probe characterization. A data-driven optimization method for the PCB layout is introduced. Experimental results validate the effectiveness of the proposed design.
- 3 February 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Dielectrics and Electrical Insulation
- Vol. 33  (3) , 1622-1629
Bubble Degassing Characteristics in Silicone Gel and Improved Degassing Process to Enhance Its Insulation Capacity
Silicone gel is widely used in the packaging of high-voltage power devices because of its sealing, high temperature resistance and good insulation performance. However, the residual bubbles of silicone gel in the process of encapsulation are very easy to produce partial discharge or even breakdown phenomenon, which seriously restricts insulation reliability of high voltage power devices. To this end, the bubble motion in silicone gel during degassing is investigated to guide process optimization and enhance insulation performance in this paper. Firstly, by simulation and experiment, the influence of viscosity of silicone gel and different degassing pressure conditions on rising velocity of the bubble with initial bubble diameter are obtained. Then, the influence of thickness of silicone gel on the bubble rising velocity rate is also investigated. Furthermore, an optimized repeated degassing curve and stratified degassing method are proposed. The experimental results show that the breakdown voltage of the silicone gel treated by the repeated pressure buck process method increased by 16.84% compared with original process. Moreover, the insulation capability of silicone gel made by stratified degassing method is at least increased by 5.8%. Overall, methods proposed in this paper provide guidance for the advanced preparation process of silicone gel to promote insulation capability of IGBT device encapsulation.
- 3 February 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Dielectrics and Electrical Insulation
- Vol. 33  (3) , 1622-1629
Bubble Degassing Characteristics in Silicone Gel and Improved Degassing Process to Enhance Its Insulation Capacity
Silicone gel is widely used in the packaging of high-voltage power devices because of its sealing, high temperature resistance and good insulation performance. However, the residual bubbles of silicone gel in the process of encapsulation are very easy to produce partial discharge or even breakdown phenomenon, which seriously restricts insulation reliability of high voltage power devices. To this end, the bubble motion in silicone gel during degassing is investigated to guide process optimization and enhance insulation performance in this paper. Firstly, by simulation and experiment, the influence of viscosity of silicone gel and different degassing pressure conditions on rising velocity of the bubble with initial bubble diameter are obtained. Then, the influence of thickness of silicone gel on the bubble rising velocity rate is also investigated. Furthermore, an optimized repeated degassing curve and stratified degassing method are proposed. The experimental results show that the breakdown voltage of the silicone gel treated by the repeated pressure buck process method increased by 16.84% compared with original process. Moreover, the insulation capability of silicone gel made by stratified degassing method is at least increased by 5.8%. Overall, methods proposed in this paper provide guidance for the advanced preparation process of silicone gel to promote insulation capability of IGBT device encapsulation.
- 11 December 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Computer-Aided Design of Integrated Circuits and Systems
- Vol. PP  (02780070) , 1
A Transient State Electric Field Model Considering Maxwell-Wagner Effect for Electric Field Calculation of Semiconductor with Multilayer Dielectrics
In high-voltage devices, the voltage-blocking structure is composed of chip termination and packaging, which is a semiconductor with multilayer dielectrics stacked structure. However, existing TCAD (Technology Computer-Aided Design) software fails to consider the Maxwell-Wagner effect in multilayer dielectrics. To address this issue, a transient state electric field model considering the Maxwell-Wagner effect for dielectric materials is developed and integrated into the standard TCAD workflow with acceptable computational cost. By experimental verification, the proposed model corresponds well with the measurement results and it reveals the influence of the Maxwell-Wagner effect in the multilayer dielectrics on the electric field characteristics of semiconductor. Moreover, the maximum relative error between the simulation based on the proposed model and measurement is 2.3%, while it is 15.38% when using original model in existing TCAD software. In addition, the influence of mesh size and parameters of dielectrics are discussed. Overall, the proposed model yields more accurate simulation results and can be used for robust insulation design under transient state.
- 11 December 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Computer-Aided Design of Integrated Circuits and Systems
- Vol. PP  (02780070) , 1
A Transient State Electric Field Model Considering Maxwell-Wagner Effect for Electric Field Calculation of Semiconductor with Multilayer Dielectrics
In high-voltage devices, the voltage-blocking structure is composed of chip termination and packaging, which is a semiconductor with multilayer dielectrics stacked structure. However, existing TCAD (Technology Computer-Aided Design) software fails to consider the Maxwell-Wagner effect in multilayer dielectrics. To address this issue, a transient state electric field model considering the Maxwell-Wagner effect for dielectric materials is developed and integrated into the standard TCAD workflow with acceptable computational cost. By experimental verification, the proposed model corresponds well with the measurement results and it reveals the influence of the Maxwell-Wagner effect in the multilayer dielectrics on the electric field characteristics of semiconductor. Moreover, the maximum relative error between the simulation based on the proposed model and measurement is 2.3%, while it is 15.38% when using original model in existing TCAD software. In addition, the influence of mesh size and parameters of dielectrics are discussed. Overall, the proposed model yields more accurate simulation results and can be used for robust insulation design under transient state.
- 9 December 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Power Electronics
- Vol. 41  (5) , 7800-7812
A Noninvasive Monitoring Method for Uniformity of Pressure Distribution on the Chip Surface in Single-Chip Press-Pack IGBTs With Turn-Off v CE
In a press-pack insulated gate bipolar transistor (PPI), the uniformity of pressure distribution on the chip surface significantly impacts its reliability. Currently, this uniformity is primarily assessed by pressure film, which is invasive and limited. This article proposes an electrical parameter method for monitoring uniformity of pressure distribution on the chip surface in single-chip PPIs offline at room temperature. First, the collector voltage at a specified moment during turn-off, Vce,D, is introduced as a highly sensitive indicator of this uniformity. For example, a mere 1 mm misalignment between the clamping force center and the chip center can cause a variation in Vce,D exceeding 100 V. To minimize interference from other factors, monitoring with Vce,D is performed at room temperature, and its implementation method is carefully developed. Second, the proposed method is validated with a specially designed experimental platform. Its broad applicability across various chip types and packaging technologies is illustrated as well. Moreover, a detailed comparison between this novel method and traditional pressure film is provided. The proposed method is noninvasive, highly sensitive, and supports quantitative assessment. Finally, the method's measurement error margin, and its great potential for extension to multichip PPIs are discussed.
- 9 December 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Power Electronics
- Vol. 41  (5) , 7800-7812
A Noninvasive Monitoring Method for Uniformity of Pressure Distribution on the Chip Surface in Single-Chip Press-Pack IGBTs With Turn-Off v CE
In a press-pack insulated gate bipolar transistor (PPI), the uniformity of pressure distribution on the chip surface significantly impacts its reliability. Currently, this uniformity is primarily assessed by pressure film, which is invasive and limited. This article proposes an electrical parameter method for monitoring uniformity of pressure distribution on the chip surface in single-chip PPIs offline at room temperature. First, the collector voltage at a specified moment during turn-off, Vce,D, is introduced as a highly sensitive indicator of this uniformity. For example, a mere 1 mm misalignment between the clamping force center and the chip center can cause a variation in Vce,D exceeding 100 V. To minimize interference from other factors, monitoring with Vce,D is performed at room temperature, and its implementation method is carefully developed. Second, the proposed method is validated with a specially designed experimental platform. Its broad applicability across various chip types and packaging technologies is illustrated as well. Moreover, a detailed comparison between this novel method and traditional pressure film is provided. The proposed method is noninvasive, highly sensitive, and supports quantitative assessment. Finally, the method's measurement error margin, and its great potential for extension to multichip PPIs are discussed.
- 21 November 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Dielectrics and Electrical Insulation
- Vol. PP  (10709878) , 1
Space Charge Characteristic of Silicone Elastomer Used in SiC Device under High Temperature up to 200°C
In order to study the space charge characteristics of silicone elastomers at high temperatures, a high-temperature PEA space charge characteristic measurement system with a temperature range of room temperature (25°C)-200°C was developed in this paper. The system developed in this paper can meet the temperature control and measurement requirements through actual temperature measurement and calibration. Through this system, this paper studies the space charge characteristics and short-circuit characteristics of silicone elastomers under different polarity DC voltages in the range of 25°C-200°C. With the increase of temperature, the charge accumulation depth first increases and then decreases, and the charge accumulation amount first increases and then decreases. The migration rate of negative polarity charges is greater than that of positive polarity charges. The trap characteristics of silicone elastomers at different temperatures are analyzed by charge dissipation characteristics. At lower temperatures, the deep trap density is greater than the shallow trap density, whether it is electron traps or hole traps. When it is greater than a certain temperature, the shallow trap density is greater than the deep trap density. Temperature affects charge generation and charge migration. At low temperatures, the charge injection amount increases and becomes the dominant factor. When the temperature increases, the charge mobility increases and becomes the dominant factor, so the charge accumulation amount and trap density both increase and then decrease with temperature.
- 21 November 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Dielectrics and Electrical Insulation
- Vol. PP  (10709878) , 1
Space Charge Characteristic of Silicone Elastomer Used in SiC Device under High Temperature up to 200°C
In order to study the space charge characteristics of silicone elastomers at high temperatures, a high-temperature PEA space charge characteristic measurement system with a temperature range of room temperature (25°C)-200°C was developed in this paper. The system developed in this paper can meet the temperature control and measurement requirements through actual temperature measurement and calibration. Through this system, this paper studies the space charge characteristics and short-circuit characteristics of silicone elastomers under different polarity DC voltages in the range of 25°C-200°C. With the increase of temperature, the charge accumulation depth first increases and then decreases, and the charge accumulation amount first increases and then decreases. The migration rate of negative polarity charges is greater than that of positive polarity charges. The trap characteristics of silicone elastomers at different temperatures are analyzed by charge dissipation characteristics. At lower temperatures, the deep trap density is greater than the shallow trap density, whether it is electron traps or hole traps. When it is greater than a certain temperature, the shallow trap density is greater than the deep trap density. Temperature affects charge generation and charge migration. At low temperatures, the charge injection amount increases and becomes the dominant factor. When the temperature increases, the charge mobility increases and becomes the dominant factor, so the charge accumulation amount and trap density both increase and then decrease with temperature.