Yiming Wang
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Yiming Wang has a total of 10 co-authors. Here are the top co-authors by number of shared publications:
- Yanjun Liu
Key Laboratory of High-Efficiency and Clean Mechanical Manufacture of Ministry of Education, National Demonstration Center for Experimental Mechanical Engineering Education, School of Mechanical Engineering, Shandong University, Jinan 250061, China
3 shared publications - Yun Chen
Institute of Marine Science and Technology, Shandong University, Qingdao 266237, China
2 shared publications - Gang Xue
Key Laboratory of High-Efficiency and Clean Mechanical Manufacture of Ministry of Education, National Demonstration Center for Experimental Mechanical Engineering Education, School of Mechanical Engineering, Shandong University, Jinan 250061, China
1 shared publication - Hongjun Liu
Shenyang Aerospace University,Shenyang,China
1 shared publication - Li Zhang
Southern Marine Science and Engineering Guangdong Laboratory (Zhanjiang)
1 shared publication - Qiang Zhang
School of Mechanical Engineering, Shandong University, Jinan 250061, China
1 shared publication
Latest Publications
- Open Access
Auxiliary Heat System Design and Off-Design Performance Optimization of OTEC Radial Inflow Turbine
In this paper, solar energy is used as the auxiliary heat source of the ocean thermal energy radial inflow turbine, and the thermodynamic model of the circulation system is established. In addition, the ejector is introduced into the ocean thermal power generation system, and the process simulation is carried out using Aspen Plus V12. To address performance attenuation of the radial turbine under varying working conditions, shape optimization of a 30 kW OTEC radial turbine was conducted. Finally, the off-design performance variation in the radial inflow turbine is analyzed in the presence of a solar auxiliary heat source. The results show that the use of an auxiliary heat source can effectively improve the cycle efficiency of the system and is also conducive to the stable operation of the radial turbine. Under the condition of auxiliary heat source, the system cycle efficiency is increased by 2.269%.
Open AccessAuxiliary Heat System Design and Off-Design Performance Optimization of OTEC Radial Inflow Turbine
In this paper, solar energy is used as the auxiliary heat source of the ocean thermal energy radial inflow turbine, and the thermodynamic model of the circulation system is established. In addition, the ejector is introduced into the ocean thermal power generation system, and the process simulation is carried out using Aspen Plus V12. To address performance attenuation of the radial turbine under varying working conditions, shape optimization of a 30 kW OTEC radial turbine was conducted. Finally, the off-design performance variation in the radial inflow turbine is analyzed in the presence of a solar auxiliary heat source. The results show that the use of an auxiliary heat source can effectively improve the cycle efficiency of the system and is also conducive to the stable operation of the radial turbine. Under the condition of auxiliary heat source, the system cycle efficiency is increased by 2.269%.
- Open Access
- 3 December 2023
- Published by MDPI AG in Journal of Marine Science and Engineering
- Vol. 11 (12) , 2293
Parameter Optimization and Performance Research: Radial Inflow Turbine in Ocean Thermal Energy Conversion
Combining one-dimensional parameter optimization and three-dimensional modeling optimization, a 30 kW radial inflow turbine for ocean thermal energy conversion was designed. In this paper, the effects of blade tip clearance, blade number, twist angle, and wheel–diameter ratio on the radial inflow turbine were analyzed. The results show that the model prediction method based on 3D numerical simulation data can effectively complete secondary optimization of the radial turbine rotor. The prediction model can be used to directly obtain the optimal modeling parameter of the rotor. The tip clearance, blade number, twist angle, wheel–diameter ratio, and shaft efficiency were found to be 0.273 mm, 16, 43.378°, 0.241, and 88.467%, respectively. The optimized shaft efficiency of the turbine was found to be 2.239% higher than the one-dimensional design result, which is of great significance in reducing the system’s power generation costs and promoting the application of this approach in engineering power generation using ocean thermal energy.
- 3 December 2023
- Published by MDPI AG in Journal of Marine Science and Engineering
- Vol. 11 (12) , 2293
Open AccessParameter Optimization and Performance Research: Radial Inflow Turbine in Ocean Thermal Energy Conversion
Combining one-dimensional parameter optimization and three-dimensional modeling optimization, a 30 kW radial inflow turbine for ocean thermal energy conversion was designed. In this paper, the effects of blade tip clearance, blade number, twist angle, and wheel–diameter ratio on the radial inflow turbine were analyzed. The results show that the model prediction method based on 3D numerical simulation data can effectively complete secondary optimization of the radial turbine rotor. The prediction model can be used to directly obtain the optimal modeling parameter of the rotor. The tip clearance, blade number, twist angle, wheel–diameter ratio, and shaft efficiency were found to be 0.273 mm, 16, 43.378°, 0.241, and 88.467%, respectively. The optimized shaft efficiency of the turbine was found to be 2.239% higher than the one-dimensional design result, which is of great significance in reducing the system’s power generation costs and promoting the application of this approach in engineering power generation using ocean thermal energy.
- 27 October 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- Vol. 55, 520-524
Tool wear prediction method based on KPCA and GWO-LS-SVM
To improve the real-time and accuracy of detecting tool wear status, a new tool wear prediction method based on Kernel Principal Component Analysis (KPCA) and Grey Wolf Optimized Least Squares Support Vector Machine (GWO-LS-SVM) was proposed. This method uses cutting force signals to extract multiple features correlated with tool wear from time domain, frequency domain, and wavelet domain, and performs dimensionality reduction processing through kernel principal component analysis, then uses the gray wolf to optimize the LS-SVM to achieve prediction of tool wear. Through experimental comparison and verification, it is found that this method can accurately predict the value of tool wear, and has good real-time performance.
- 27 October 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- Vol. 55, 520-524
Tool wear prediction method based on KPCA and GWO-LS-SVM
To improve the real-time and accuracy of detecting tool wear status, a new tool wear prediction method based on Kernel Principal Component Analysis (KPCA) and Grey Wolf Optimized Least Squares Support Vector Machine (GWO-LS-SVM) was proposed. This method uses cutting force signals to extract multiple features correlated with tool wear from time domain, frequency domain, and wavelet domain, and performs dimensionality reduction processing through kernel principal component analysis, then uses the gray wolf to optimize the LS-SVM to achieve prediction of tool wear. Through experimental comparison and verification, it is found that this method can accurately predict the value of tool wear, and has good real-time performance.
- Open Access
- 20 August 2021
- Published by MDPI AG in Journal of Marine Science and Engineering
- Vol. 9 (8) , 901
Research on Optimization and Verification of the Number of Stator Blades of kW Ammonia Working Medium Radial Flow Turbine in Ocean Thermal Energy Conversion
Ocean Thermal Energy Conversion (OTEC) is one of the emerging industries of ocean energy and an important link in carbon neutrality. Turbine is a key component of ocean thermal energy conversion, which has an important impact on the performance and energy conversion efficiency of the system. This paper fully considers the application characteristics of ocean thermal energy conversion and the state conversion characteristics of ammonia working fluid. Taking the 100 kW radial inflow turbine in the OTEC application system as an example, based on the design, the turbine is optimized for the key parameters of the turbine stator and the influence of different geometric parameters is analyzed. Subsequently, the optimization results are verified by CFD numerical simulation analysis under different conditions. The results show that the number of stator blades has an important influence on the performance of the turbine. Further optimization studies have shown that through optimization, when the number of stator blades is 33, the internal flow field performance is the best, and the working conditions of the inlet and outlet working fluids are in accordance with the design points without obvious shock wave and reverse flow phenomenon, the efficiency is 89.46%, 3.94% higher than the design value.
- 20 August 2021
- Published by MDPI AG in Journal of Marine Science and Engineering
- Vol. 9 (8) , 901
Open AccessResearch on Optimization and Verification of the Number of Stator Blades of kW Ammonia Working Medium Radial Flow Turbine in Ocean Thermal Energy Conversion
Ocean Thermal Energy Conversion (OTEC) is one of the emerging industries of ocean energy and an important link in carbon neutrality. Turbine is a key component of ocean thermal energy conversion, which has an important impact on the performance and energy conversion efficiency of the system. This paper fully considers the application characteristics of ocean thermal energy conversion and the state conversion characteristics of ammonia working fluid. Taking the 100 kW radial inflow turbine in the OTEC application system as an example, based on the design, the turbine is optimized for the key parameters of the turbine stator and the influence of different geometric parameters is analyzed. Subsequently, the optimization results are verified by CFD numerical simulation analysis under different conditions. The results show that the number of stator blades has an important influence on the performance of the turbine. Further optimization studies have shown that through optimization, when the number of stator blades is 33, the internal flow field performance is the best, and the working conditions of the inlet and outlet working fluids are in accordance with the design points without obvious shock wave and reverse flow phenomenon, the efficiency is 89.46%, 3.94% higher than the design value.