Stefano Stanzione
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Stefano Stanzione has a total of 16 co-authors. Here are the top co-authors by number of shared publications:
- Arjan Breeschoten
Imec/Holst Centre, Eindhoven Netherlands
1 shared publication C. Van Hoof
Holst Centre Eindhoven The Netherlands
1 shared publicationC. van Liempd
Holst Centre Eindhoven The Netherlands
1 shared publication- Chris Van Hoof
IMEC, Leuven, Belgium
1 shared publication Chris van Hoof
Holst Centre/Imec
1 shared publicationChris van Liempd
Holst Centre/Imec
1 shared publication
Latest Publications
- 2 October 2019
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Biomedical Circuits and Systems
- Vol. 13 (6) , 1506-1517
A 769 μW Battery-Powered Single-Chip SoC With BLE for Multi-Modal Vital Sign Monitoring Health Patches
An all-in-one battery powered low-power SoC for measuring multiple vital signs with wearables is proposed. All functionality needed in a typical wearable use case scenario, including dedicated readouts, power management circuitry, digital signal processing and wireless communication (BLE) is integrated in a single die. This high level of integration allows an unprecedented level of miniaturization leading to smaller component count which reduces cost and improves comfort and signal integrity. The SoC includes an ECG, Bio-Impedance and a fully differential PPG readout and can interface with external sensors (like an IMU). In a typical application scenario where all sensor readouts are enabled and key features (like heart rate) are calculated on the chip and streamed over the radio, the SoC consumes only 769μW from the regulated 1.2V supply.
- 2 October 2019
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Biomedical Circuits and Systems
- Vol. 13 (6) , 1506-1517
A 769 μW Battery-Powered Single-Chip SoC With BLE for Multi-Modal Vital Sign Monitoring Health Patches
An all-in-one battery powered low-power SoC for measuring multiple vital signs with wearables is proposed. All functionality needed in a typical wearable use case scenario, including dedicated readouts, power management circuitry, digital signal processing and wireless communication (BLE) is integrated in a single die. This high level of integration allows an unprecedented level of miniaturization leading to smaller component count which reduces cost and improves comfort and signal integrity. The SoC includes an ECG, Bio-Impedance and a fully differential PPG readout and can interface with external sensors (like an IMU). In a typical application scenario where all sensor readouts are enabled and key features (like heart rate) are calculated on the chip and streamed over the radio, the SoC consumes only 769μW from the regulated 1.2V supply.
- 6 August 2016
- Published by Springer Nature
- p. 343-352
An Ultra-Low-Power Electrostatic Energy Harvester Interface
- 6 August 2016
- Published by Springer Nature
- p. 343-352
An Ultra-Low-Power Electrostatic Energy Harvester Interface
- Open Access
- 1 January 2013
- Published by Institution of Engineering and Technology (IET) in Electronics Letters
- Vol. 49 (3) , 210-211
Integrated asynchronous high‐voltage DC–DC buck converter for energy harvesting applications
Reported is a high‐voltage DC–DC buck converter to interface energy harvesters in ultra‐low‐power wireless sensing applications. A measured efficiency between 61 and 91% has been obtained for input power between 10 and 1000 µW and for a large input voltage range between 5 and 60 V. To minimise the power consumption of the control circuits, an asynchronous implementation was used with a zero static power high‐voltage level shifter and a widely applicable ultra‐low‐power n‐switch control circuit architecture.
- 1 January 2013
- Published by Institution of Engineering and Technology (IET) in Electronics Letters
- Vol. 49 (3) , 210-211
Open AccessIntegrated asynchronous high‐voltage DC–DC buck converter for energy harvesting applications
Reported is a high‐voltage DC–DC buck converter to interface energy harvesters in ultra‐low‐power wireless sensing applications. A measured efficiency between 61 and 91% has been obtained for input power between 10 and 1000 µW and for a large input voltage range between 5 and 60 V. To minimise the power consumption of the control circuits, an asynchronous implementation was used with a zero static power high‐voltage level shifter and a widely applicable ultra‐low‐power n‐switch control circuit architecture.