Hee-Seon Seo
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Hee-Seon Seo has a total of 43 co-authors. Here are the top co-authors by number of shared publications:
- Yohan Cho
Agency for Defense Development, Changwon 51678, Republic of Korea
6 shared publications - Yub Je
Agency for Defense Development, Changwon 51678, Republic of Korea
4 shared publications - Hak Yi
Department of Mechanical Engineering, Kyungpook National University, Daegu, Korea
3 shared publications - Jongkil Lee
Department of Mechanical Engineering Education, Gyeongkuk National University, Andong 36729, Republic of Korea
3 shared publications - Kwan Kyu Park
Department of Convergence Mechanical Engineering, Hanyang University, Seoul 04763, Republic of Korea
3 shared publications - Yongrae Roh
School of Mechanical Engineering, Kyungpook National University, Daegu 41566, Republic of Korea
3 shared publications
Latest Publications
- Open Access
High-Power Characteristics of Piezoelectric Transducers Based on [011] Poled Relaxor-PT Single Crystals
[011] poled relaxor-PT single crystals provide superior piezoelectric constants and electromechanical coupling factors in the 32 crystal directions, and also exhibit high electrical stability under compressive stresses and temperature changes. In particular, Mn-doped Pb(In1/2Nb1/2)O3-Pb(Mg1/3Nb2/3)O3-PbTiO3 (Mn:PIN-PMN-PT) single crystals show a superior coercive field (EC ≥ 8.0 kV/cm) and mechanical quality factor (Qm ≥ 1030), making them suitable for high-power transducers. The high-power characteristics of [011] poled single crystals have been verified from a material perspective; thus, further investigation is required from a transducer perspective. In this study, the high-power characteristics of piezoelectric transducers based on [011] poled PIN-PMN-PT and [011] poled Mn:PIN-PMN-PT single crystals were investigated. To analyze the driving limits of the single crystals, the polarization–electric field (P–E) curves, as a function of the driving electric field, were measured. The results showed that [011] poled Mn:PIN-PMN-PT single crystals demonstrate lower energy loss and THD (Total Harmonic Distortion), directly relating to the driving efficiency and linearity of the transducer. Additionally, [011] poled Mn:PIN-PMN-PT crystals provide excellent stability under the compressive stress and temperature changes. To analyze the high-power characteristics of [011] poled single-crystal transducers, two types of barrel-stave transducers, based on [011] poled PIN-PMN-PT and [011] poled Mn:PIN-PMN-PT, were designed and fabricated. The changes in the impedance and transmitting voltage response with respect to the driving electric fields were measured, and the energy loss and THD of the transducers with respect to the driving electric fields were examined to assess the driving limit of the [011] poled single-crystal transducer. The high-power characteristic tests confirmed the stability of [011] poled Mn:PIN-PMN-PT single crystals and verified their potential for high-power transducer applications.
Open AccessHigh-Power Characteristics of Piezoelectric Transducers Based on [011] Poled Relaxor-PT Single Crystals
[011] poled relaxor-PT single crystals provide superior piezoelectric constants and electromechanical coupling factors in the 32 crystal directions, and also exhibit high electrical stability under compressive stresses and temperature changes. In particular, Mn-doped Pb(In1/2Nb1/2)O3-Pb(Mg1/3Nb2/3)O3-PbTiO3 (Mn:PIN-PMN-PT) single crystals show a superior coercive field (EC ≥ 8.0 kV/cm) and mechanical quality factor (Qm ≥ 1030), making them suitable for high-power transducers. The high-power characteristics of [011] poled single crystals have been verified from a material perspective; thus, further investigation is required from a transducer perspective. In this study, the high-power characteristics of piezoelectric transducers based on [011] poled PIN-PMN-PT and [011] poled Mn:PIN-PMN-PT single crystals were investigated. To analyze the driving limits of the single crystals, the polarization–electric field (P–E) curves, as a function of the driving electric field, were measured. The results showed that [011] poled Mn:PIN-PMN-PT single crystals demonstrate lower energy loss and THD (Total Harmonic Distortion), directly relating to the driving efficiency and linearity of the transducer. Additionally, [011] poled Mn:PIN-PMN-PT crystals provide excellent stability under the compressive stress and temperature changes. To analyze the high-power characteristics of [011] poled single-crystal transducers, two types of barrel-stave transducers, based on [011] poled PIN-PMN-PT and [011] poled Mn:PIN-PMN-PT, were designed and fabricated. The changes in the impedance and transmitting voltage response with respect to the driving electric fields were measured, and the energy loss and THD of the transducers with respect to the driving electric fields were examined to assess the driving limit of the [011] poled single-crystal transducer. The high-power characteristic tests confirmed the stability of [011] poled Mn:PIN-PMN-PT single crystals and verified their potential for high-power transducer applications.
- Open Access
- 23 December 2024
- Published by Springer Nature in Journal of the Korean Ceramic Society
- Vol. 62  (2) , 350-358
Mechanical constraint to extend the operational range of (011)-oriented Mn-doped PIN–PMN–PT single crystals
We investigated mechanical stress-dependent behaviors of (011)-oriented Mn-doped PIN–PMN–PT single crystals to further improve their stabilities for high-power piezoelectric applications. In contrast to the common belief that mechanical constraint induces depolarization of active piezoelectric materials, the (011)-oriented single crystals demonstrated up to 44% of enhancements in their coercive field when mechanical stress is loaded on the specific flank surfaces of the single crystals. Furthermore, the suggested strategy is also feasible over practical operational temperatures for electroacoustic sensors (5–60 °C), which is beneficial to high-temperature applications. Nevertheless, consistent with the generally accepted trade-off, their electromechanical responses are inevitably degraded at constrained states due to less shear deformation which is key in piezoelectricity of relaxor-PT single crystals. We hope that the current work will elucidate mechanical stress-dependent behaviors of domain-engineered anisotropic relaxor-PT single crystals and provide a clue for a proper selection of prestress levels to achieve better performances of electroacoustic transducers in a variety of environments.
- 23 December 2024
- Published by Springer Nature in Journal of the Korean Ceramic Society
- Vol. 62  (2) , 350-358
Open AccessMechanical constraint to extend the operational range of (011)-oriented Mn-doped PIN–PMN–PT single crystals
We investigated mechanical stress-dependent behaviors of (011)-oriented Mn-doped PIN–PMN–PT single crystals to further improve their stabilities for high-power piezoelectric applications. In contrast to the common belief that mechanical constraint induces depolarization of active piezoelectric materials, the (011)-oriented single crystals demonstrated up to 44% of enhancements in their coercive field when mechanical stress is loaded on the specific flank surfaces of the single crystals. Furthermore, the suggested strategy is also feasible over practical operational temperatures for electroacoustic sensors (5–60 °C), which is beneficial to high-temperature applications. Nevertheless, consistent with the generally accepted trade-off, their electromechanical responses are inevitably degraded at constrained states due to less shear deformation which is key in piezoelectricity of relaxor-PT single crystals. We hope that the current work will elucidate mechanical stress-dependent behaviors of domain-engineered anisotropic relaxor-PT single crystals and provide a clue for a proper selection of prestress levels to achieve better performances of electroacoustic transducers in a variety of environments.
- Open Access
- 16 July 2024
- Published by MDPI AG in Micromachines
- Vol. 15  (7) , 917
Derivation of Equivalent Material Coefficients of 2-2 Piezoelectric Single Crystal Composite
Piezoelectric composites, which consist of piezoelectric materials and polymers, are widely employed in various applications such as underwater sonar transducers and medical diagnostic ultrasonic transducers. Acoustic transducers based on piezoelectric composites can have high sensitivity with broad bandwidth. In recent studies, it is demonstrated that 2-2 composites based on single crystals provide further increased sensitivity and wide bandwidth. In order to utilize a 2-2 composite in acoustic sensors, it is required to demonstrate the full material coefficients of the 2-2 composite. In this study, we investigated an analytic solution for determining equivalent material coefficients of a 2-2 composite. Impedance spectrums of the single-phase resonators with equivalent material coefficients and 2-2 composite resonators were compared by the finite element method in order to verify the analytic solutions. Furthermore, the equivalent material coefficients derived from the analytic solution were also verified by comparing the measured and the simulated impedance spectrums. The difference in resonance and anti-resonance frequencies between the measured and simulated impedance spectrums was around 0.5% and 1.2%. By utilizing the analytic solutions in this study, it is possible to accurately derive full equivalent material coefficients of a 2-2 composite, which are essential for the development of acoustic sensors.
- 16 July 2024
- Published by MDPI AG in Micromachines
- Vol. 15  (7) , 917
Open AccessDerivation of Equivalent Material Coefficients of 2-2 Piezoelectric Single Crystal Composite
Piezoelectric composites, which consist of piezoelectric materials and polymers, are widely employed in various applications such as underwater sonar transducers and medical diagnostic ultrasonic transducers. Acoustic transducers based on piezoelectric composites can have high sensitivity with broad bandwidth. In recent studies, it is demonstrated that 2-2 composites based on single crystals provide further increased sensitivity and wide bandwidth. In order to utilize a 2-2 composite in acoustic sensors, it is required to demonstrate the full material coefficients of the 2-2 composite. In this study, we investigated an analytic solution for determining equivalent material coefficients of a 2-2 composite. Impedance spectrums of the single-phase resonators with equivalent material coefficients and 2-2 composite resonators were compared by the finite element method in order to verify the analytic solutions. Furthermore, the equivalent material coefficients derived from the analytic solution were also verified by comparing the measured and the simulated impedance spectrums. The difference in resonance and anti-resonance frequencies between the measured and simulated impedance spectrums was around 0.5% and 1.2%. By utilizing the analytic solutions in this study, it is possible to accurately derive full equivalent material coefficients of a 2-2 composite, which are essential for the development of acoustic sensors.
- Open Access
Theoretical and Experimental Studies on Sensitivity and Bandwidth of Thickness-Mode Driving Hydrophone Utilizing A 2-2 Piezoelectric Single Crystal Composite
Piezoelectric composites, which consist of a piezoelectric material and a polymer, have been extensively studied for the applications of underwater sonar sensors and medical diagnostic ultrasonic transducers. Acoustic sensors utilizing piezoelectric composites can have a high sensitivity and wide bandwidth because of their high piezoelectric coefficient and low acoustic impedance compared to single-phase piezoelectric materials. In this study, a thickness-mode driving hydrophone utilizing a 2-2 piezoelectric single crystal composite was examined. From the theoretical and numerical analysis, material properties that determine the bandwidth and sensitivity of the thickness-mode piezoelectric plate were derived, and the voltage sensitivity of piezoelectric plates with various configurations was compared. It was shown that the 2-2 composite with [011] poled single crystals and epoxy polymers can provide high sensitivity and wide bandwidth when used for hydrophones with a thickness resonance mode. The hydrophone element was designed and fabricated to have a thickness mode at a frequency around 220 kHz by attaching a composite plate of quarter-wavelength thickness to a hard baffle. The fabricated hydrophone demonstrated an open circuit voltage sensitivity of more than −180 dB re 1 V/μPa at the resonance frequency and a −3 dB bandwidth of more than 55 kHz. The theoretical and experimental studies show that the 2-2 single crystal composite can have a high sensitivity and wide bandwidth compared to other configurations of piezoelectric elements when they are used for thickness-mode hydrophones.
Open AccessTheoretical and Experimental Studies on Sensitivity and Bandwidth of Thickness-Mode Driving Hydrophone Utilizing A 2-2 Piezoelectric Single Crystal Composite
Piezoelectric composites, which consist of a piezoelectric material and a polymer, have been extensively studied for the applications of underwater sonar sensors and medical diagnostic ultrasonic transducers. Acoustic sensors utilizing piezoelectric composites can have a high sensitivity and wide bandwidth because of their high piezoelectric coefficient and low acoustic impedance compared to single-phase piezoelectric materials. In this study, a thickness-mode driving hydrophone utilizing a 2-2 piezoelectric single crystal composite was examined. From the theoretical and numerical analysis, material properties that determine the bandwidth and sensitivity of the thickness-mode piezoelectric plate were derived, and the voltage sensitivity of piezoelectric plates with various configurations was compared. It was shown that the 2-2 composite with [011] poled single crystals and epoxy polymers can provide high sensitivity and wide bandwidth when used for hydrophones with a thickness resonance mode. The hydrophone element was designed and fabricated to have a thickness mode at a frequency around 220 kHz by attaching a composite plate of quarter-wavelength thickness to a hard baffle. The fabricated hydrophone demonstrated an open circuit voltage sensitivity of more than −180 dB re 1 V/μPa at the resonance frequency and a −3 dB bandwidth of more than 55 kHz. The theoretical and experimental studies show that the 2-2 single crystal composite can have a high sensitivity and wide bandwidth compared to other configurations of piezoelectric elements when they are used for thickness-mode hydrophones.
- Open Access
A Study on the Underwater Energy Harvester with Two PVDFs Installed on the FTEH and CTEH at the End of the Support
In this study, two thin rectangular PVDFs were installed in the form of a cantilever on a FTEH (funnel-type energy harvester), and a CTEH (cymbal-type energy harvester) was fabricated in a form coupled to the upper part of the support. As a result of measuring the energy harvesting sensitivity according to the installation direction of the CTEH, a high voltage was measured in the structure installed on top of the support across all flow velocity conditions. A composite structure PVDF energy harvester combining CTEH and FTEH was fabricated and the amount of power generated was measured. As a result of measuring the open-circuit voltage of the PVDF energy harvester device with a composite structure to which the optimum resistance of CTEH of 241 kΩ and the optimum resistance of FTEH of 1474 kΩ were applied at a flow rate of 0.25 m/s, the output voltage compared to the RMS average value was 7 to 8.5 times higher for FTEH than for CTEH. When the flow rate was 0.5 m/s, the electrical energy charged for 500 s was measured as 2.0 μWs to 2.5 μWs, and when the flow speed was 0.75 m/s, it reached 2.5 μWs when charged for 300 s, generating the same amount when the flow rate increased by 50%. The time to do it was reduced by 66.7%.
Open AccessA Study on the Underwater Energy Harvester with Two PVDFs Installed on the FTEH and CTEH at the End of the Support
In this study, two thin rectangular PVDFs were installed in the form of a cantilever on a FTEH (funnel-type energy harvester), and a CTEH (cymbal-type energy harvester) was fabricated in a form coupled to the upper part of the support. As a result of measuring the energy harvesting sensitivity according to the installation direction of the CTEH, a high voltage was measured in the structure installed on top of the support across all flow velocity conditions. A composite structure PVDF energy harvester combining CTEH and FTEH was fabricated and the amount of power generated was measured. As a result of measuring the open-circuit voltage of the PVDF energy harvester device with a composite structure to which the optimum resistance of CTEH of 241 kΩ and the optimum resistance of FTEH of 1474 kΩ were applied at a flow rate of 0.25 m/s, the output voltage compared to the RMS average value was 7 to 8.5 times higher for FTEH than for CTEH. When the flow rate was 0.5 m/s, the electrical energy charged for 500 s was measured as 2.0 μWs to 2.5 μWs, and when the flow speed was 0.75 m/s, it reached 2.5 μWs when charged for 300 s, generating the same amount when the flow rate increased by 50%. The time to do it was reduced by 66.7%.
- Open Access
Development of Multilayer Transducer and Omnidirectional Reflection Model for Active Reflection Control
Underwater detection is accomplished using an underwater ultrasonic sensor, sound navigation and ranging (SONAR). Stealth to avoid detection by SONAR plays a major role in modern underwater warfare. In this study, we propose a smart skin that avoids detection by SONAR via controlling the signal reflected from an unmanned underwater vehicle (UUV). The smart skin is a multilayer transducer composed of an acoustic window, a double-layer receiver, and a single-layer transmitter. It separates the incident signal from the reflected signal from outside through the time-delay separation method and cancels the reflected wave from the phase-shifted transmission sound. The characteristics of the receiving and transmitting sensors were analyzed using a finite element analysis. Three types of devices were compared in the design of the sensors. Polyvinylidene fluoride (PVDF), which had little effect on the transmitted sound, was selected as the receiving sensor. A stacked piezoelectric transducer with high sensitivity compared to a cymbal transducer was used as the transmitter. The active reflection control system was modeled and verified using 2D 360° reflection experiments. The stealth effect that could be achieved by applying a smart skin to a UUV was presented through an active reflection–control omnidirectional reflection model.
Open AccessDevelopment of Multilayer Transducer and Omnidirectional Reflection Model for Active Reflection Control
Underwater detection is accomplished using an underwater ultrasonic sensor, sound navigation and ranging (SONAR). Stealth to avoid detection by SONAR plays a major role in modern underwater warfare. In this study, we propose a smart skin that avoids detection by SONAR via controlling the signal reflected from an unmanned underwater vehicle (UUV). The smart skin is a multilayer transducer composed of an acoustic window, a double-layer receiver, and a single-layer transmitter. It separates the incident signal from the reflected signal from outside through the time-delay separation method and cancels the reflected wave from the phase-shifted transmission sound. The characteristics of the receiving and transmitting sensors were analyzed using a finite element analysis. Three types of devices were compared in the design of the sensors. Polyvinylidene fluoride (PVDF), which had little effect on the transmitted sound, was selected as the receiving sensor. A stacked piezoelectric transducer with high sensitivity compared to a cymbal transducer was used as the transmitter. The active reflection control system was modeled and verified using 2D 360° reflection experiments. The stealth effect that could be achieved by applying a smart skin to a UUV was presented through an active reflection–control omnidirectional reflection model.
- Open Access
Impedance Coupled Voltage Boosting Circuit for Polyvinylidene Fluoride Based Energy Harvester
Polyvinylidene fluoride (PVDF) is an emerging method for energy harvesting by fluid motion with superior flexibility. However, the PVDF energy harvester, which has a high internal impedance and generates a low voltage, has a large power transmission loss. To overcome this problem, we propose an impedance-coupled voltage-boosting circuit (IC-VBC) that reduces the impedance of the PVDF energy harvester and boosts the voltage. SPICE simulation results show that IC-VBC reduces the impedance of the PVDF energy harvester from 4.3 MΩ to 320 kΩ and increases the output voltage by 2.52 times. We successfully charged lithium-ion batteries using the PVDF energy harvester and IC-VBC with low-speed wind power generation.
Open AccessImpedance Coupled Voltage Boosting Circuit for Polyvinylidene Fluoride Based Energy Harvester
Polyvinylidene fluoride (PVDF) is an emerging method for energy harvesting by fluid motion with superior flexibility. However, the PVDF energy harvester, which has a high internal impedance and generates a low voltage, has a large power transmission loss. To overcome this problem, we propose an impedance-coupled voltage-boosting circuit (IC-VBC) that reduces the impedance of the PVDF energy harvester and boosts the voltage. SPICE simulation results show that IC-VBC reduces the impedance of the PVDF energy harvester from 4.3 MΩ to 320 kΩ and increases the output voltage by 2.52 times. We successfully charged lithium-ion batteries using the PVDF energy harvester and IC-VBC with low-speed wind power generation.
- Open Access
Fabrication and Underwater Testing of a Vector Hydrophone Comprising a Triaxial Piezoelectric Accelerometer and Spherical Hydrophone
A vector hydrophone is an underwater acoustic sensor that can detect the direction of a sound source. Wide-band characteristics and high sensitivity enhance the performance of underwater surveillance systems in complex environments. A vector hydrophone comprising a triaxial piezoelectric accelerometer and spherical hydrophone was fabricated and tested in the air and underwater. The vector hydrophone was designed to exceed the quantitative figures of merit (i.e., receiving voltage sensitivity and bandwidth) of commercially available hydrophones. Accelerometer performance was enhanced by placing a pair of piezoelectric single crystals on each axis and modifying the seismic mass material. The receiving voltage sensitivity of the omnidirectional hydrophone was approximately −160 dB relative to with the amplifier in water; the sensitivity of the accelerometer exceeded 300 mV/g in air and −215 dB relative to underwater over the frequency range of interest. The receiving directivity of the vector hydrophone was validated underwater, which confirmed that it could detect the direction of a sound source.Open AccessFabrication and Underwater Testing of a Vector Hydrophone Comprising a Triaxial Piezoelectric Accelerometer and Spherical Hydrophone
A vector hydrophone is an underwater acoustic sensor that can detect the direction of a sound source. Wide-band characteristics and high sensitivity enhance the performance of underwater surveillance systems in complex environments. A vector hydrophone comprising a triaxial piezoelectric accelerometer and spherical hydrophone was fabricated and tested in the air and underwater. The vector hydrophone was designed to exceed the quantitative figures of merit (i.e., receiving voltage sensitivity and bandwidth) of commercially available hydrophones. Accelerometer performance was enhanced by placing a pair of piezoelectric single crystals on each axis and modifying the seismic mass material. The receiving voltage sensitivity of the omnidirectional hydrophone was approximately −160 dB relative to with the amplifier in water; the sensitivity of the accelerometer exceeded 300 mV/g in air and −215 dB relative to underwater over the frequency range of interest. The receiving directivity of the vector hydrophone was validated underwater, which confirmed that it could detect the direction of a sound source. - Open Access
Equivalent Circuit to Analyze the Transmitting Characteristics of a Cymbal Array
A cymbal transducer has a simple structure consisting of a piezoceramic disk and metallic caps and has broadband characteristics when built as an array. The finite element method (FEM) is generally used to analyze the characteristics of acoustic transducers. However, the FEM requires a longer analysis time as the model becomes larger, which makes it limited and less efficient for analyzing the cymbal array. In this study, a new equivalent circuit with higher efficiency and accuracy, comparable to that of the FEM, was proposed to analyze the performance of cymbal arrays. The equivalent circuit for the array was constructed by connecting the equivalent circuits of individual cymbal transducers in parallel with a radiation impedance matrix that included both the self- and mutual radiation characteristics of the array. The validity of the new equivalent circuit was verified by measuring the transmitting voltage response of a cymbal array specimen and comparing it with that calculated using the circuit. The comparison confirmed the efficiency of the equivalent circuit in analyzing the characteristics of the cymbal array. The proposed equivalent circuit can facilitate the design of a large array of cymbal transducers.
Open AccessEquivalent Circuit to Analyze the Transmitting Characteristics of a Cymbal Array
A cymbal transducer has a simple structure consisting of a piezoceramic disk and metallic caps and has broadband characteristics when built as an array. The finite element method (FEM) is generally used to analyze the characteristics of acoustic transducers. However, the FEM requires a longer analysis time as the model becomes larger, which makes it limited and less efficient for analyzing the cymbal array. In this study, a new equivalent circuit with higher efficiency and accuracy, comparable to that of the FEM, was proposed to analyze the performance of cymbal arrays. The equivalent circuit for the array was constructed by connecting the equivalent circuits of individual cymbal transducers in parallel with a radiation impedance matrix that included both the self- and mutual radiation characteristics of the array. The validity of the new equivalent circuit was verified by measuring the transmitting voltage response of a cymbal array specimen and comparing it with that calculated using the circuit. The comparison confirmed the efficiency of the equivalent circuit in analyzing the characteristics of the cymbal array. The proposed equivalent circuit can facilitate the design of a large array of cymbal transducers.
- Open Access
- 7 April 2022
- Published by MDPI AG in Micromachines
- Vol. 13  (4) , 579
A Funnel Type PVDF Underwater Energy Harvester with Spiral Structure Mounted on the Harvester Support
For the purpose of stably supplying electric power to the underwater wireless sensor, the energy harvesting technology in which a voltage is obtained by generating displacement in a piezoelectric material using flow-induced vibration is one of the most attractive research fields. The funnel type energy harvester (FTEH) with PVDF proposed in this study is an energy harvester in which the inlet has a larger cross-sectional area than the outlet and a spiral structure is inserted to generate a vortex flow at the inlet. Based on numerical analysis, when PVDF with L = 100 mm and t = 1 mm was used, the electric power of 39 μW was generated at flow velocity of 0.25 m/s. In experiment the average RMS voltage of FTEH increased by 0.0209 V when the flow velocity increased by 1 m/s. When measured at 0.25 m/s flow velocity for 25 s, it was shown that voltage doubler rectifier (VDR) generated a voltage of 133.4 mV, 2.25 times larger than that of full bridge rectifier (FBR), and the energy charged in the capacitor was 44.3 nJ, 14% higher in VDR than that of the FBR. In addition, the VDR can deliver power of 17.75 μW for 1 k load. It is shown that if the voltage generated by the FTEH using the flow velocity is stored using the VDR electric circuit, it will greatly contribute to the stable power supply of the underwater wireless sensor.- 7 April 2022
- Published by MDPI AG in Micromachines
- Vol. 13  (4) , 579
Open AccessA Funnel Type PVDF Underwater Energy Harvester with Spiral Structure Mounted on the Harvester Support
For the purpose of stably supplying electric power to the underwater wireless sensor, the energy harvesting technology in which a voltage is obtained by generating displacement in a piezoelectric material using flow-induced vibration is one of the most attractive research fields. The funnel type energy harvester (FTEH) with PVDF proposed in this study is an energy harvester in which the inlet has a larger cross-sectional area than the outlet and a spiral structure is inserted to generate a vortex flow at the inlet. Based on numerical analysis, when PVDF with L = 100 mm and t = 1 mm was used, the electric power of 39 μW was generated at flow velocity of 0.25 m/s. In experiment the average RMS voltage of FTEH increased by 0.0209 V when the flow velocity increased by 1 m/s. When measured at 0.25 m/s flow velocity for 25 s, it was shown that voltage doubler rectifier (VDR) generated a voltage of 133.4 mV, 2.25 times larger than that of full bridge rectifier (FBR), and the energy charged in the capacitor was 44.3 nJ, 14% higher in VDR than that of the FBR. In addition, the VDR can deliver power of 17.75 μW for 1 k load. It is shown that if the voltage generated by the FTEH using the flow velocity is stored using the VDR electric circuit, it will greatly contribute to the stable power supply of the underwater wireless sensor.