Arif Caglar Konukcu
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Arif Caglar Konukcu has a total of 12 co-authors. Here are the top co-authors by number of shared publications:
Jilei Zhang
Department of Sustainable Bioproducts, College of Forest Resources, Mississippi State University, Mississippi State, USA
2 shared publications- Merve Engin
Department of Forest Industrial Engineering, Faculty of Forestry, Izmir Katip Celebi University, Izmir 35620, Türkiye
2 shared publications - Wengang Hu
Nanjing Forestry University
2 shared publications - Amil Volkan Yildizhan
İZMİR KATİP ÇELEBİ ÜNİVERSİTESİ, ORMAN FAKÜLTESİ, ORMAN ENDÜSTRİSİ MÜHENDİSLİĞİ BÖLÜMÜ
1 shared publication - Anıl Taniş
İZMİR KATİP ÇELEBİ ÜNİVERSİTESİ, ORMAN FAKÜLTESİ, ORMAN ENDÜSTRİSİ MÜHENDİSLİĞİ BÖLÜMÜ
1 shared publication - Ayberk Aydoğmuş
İzmir Katip Çelebi Üniversitesi
1 shared publication
Latest Publications
- 6 March 2026
- Published by Institutul de Chimie Macromoleculara Petru Poni in Cellulose Chemistry and Technology
- Vol. 60 (1-2) , 175-183
IMPACT OF PAPER DEINKING SLUDGE AND GLUTARALDEHYDE ON SOME NATURAL FIBER COMPOSITE PROPERTIES
This study investigated the effects of incorporating paper deinking sludge (PDS) and glutaraldehyde (GA) as an alternative binder in the production of fiberboard. Four types of fiberboards were manufactured: control boards with urea formaldehyde resin (CUF) and GA resin (CGA), and boards containing 20% (FS20) and 30% (FS30) PDS with GA resin. The mechanical properties (MOR, MOE, IB, and Shore D hardness) of the produced boards were also measured following EN standards. The GA-bonded boards (CGA, FS20, FS30) exhibited lower mechanical performance, but varying flexibility and hardness. The incorporation of PDS improved the mechanical properties compared to the CGA control. The results showed that adding up to 20% PDS content can enhance the mechanical strength of the boards. Additionally, bacterial and fungal growth on the boards was assessed using hygiene test kits. Bacterial and fungal tests revealed that GA resin effectively reduced microorganism viability on the board surfaces compared to the CUF specimen. However, boards with higher PDS content (FS30) showed more microbial growth than those with lower PDS content (FS20). This study demonstrates the potential for utilizing PDS and GA in fiberboard production, offering a sustainable alternative to conventional raw materials and resins.
- 6 March 2026
- Published by Institutul de Chimie Macromoleculara Petru Poni in Cellulose Chemistry and Technology
- Vol. 60 (1-2) , 175-183
IMPACT OF PAPER DEINKING SLUDGE AND GLUTARALDEHYDE ON SOME NATURAL FIBER COMPOSITE PROPERTIES
This study investigated the effects of incorporating paper deinking sludge (PDS) and glutaraldehyde (GA) as an alternative binder in the production of fiberboard. Four types of fiberboards were manufactured: control boards with urea formaldehyde resin (CUF) and GA resin (CGA), and boards containing 20% (FS20) and 30% (FS30) PDS with GA resin. The mechanical properties (MOR, MOE, IB, and Shore D hardness) of the produced boards were also measured following EN standards. The GA-bonded boards (CGA, FS20, FS30) exhibited lower mechanical performance, but varying flexibility and hardness. The incorporation of PDS improved the mechanical properties compared to the CGA control. The results showed that adding up to 20% PDS content can enhance the mechanical strength of the boards. Additionally, bacterial and fungal growth on the boards was assessed using hygiene test kits. Bacterial and fungal tests revealed that GA resin effectively reduced microorganism viability on the board surfaces compared to the CUF specimen. However, boards with higher PDS content (FS30) showed more microbial growth than those with lower PDS content (FS20). This study demonstrates the potential for utilizing PDS and GA in fiberboard production, offering a sustainable alternative to conventional raw materials and resins.
- 1 January 2026
- Published by BioResources in BioResources
- Vol. 21 (3)
Effect of glutaraldehyde on the antibacterial resistance of waste office paper-based boards
This research investigated the effect of glutaraldehyde solutions on antibacterial resistance of composite boards manufactured with different combinations of urea formaldehyde (UF) and glutaraldehyde (GA) binder adhesives. The composite boards were general-purpose furniture panels (e.g., kitchen worktops, shelving, laboratory benchtops, or cabinet components) intended for household or workshop environments where surfaces may encounter microbial contamination from hands or spills, but not for direct food contact. Composite boards with varying UF/GA ratios and different binder solution concentrations were manufactured. The surfaces of these boards were treated with different numbers of layers (one or two) using GA solutions at 10% and 20% concentrations. The antibacterial performance of all samples was quantitatively evaluated by measuring the percentage of microbial growth. The results revealed a strong synergistic effect between the binder chemistry and surface treatment on antibacterial activity. The highest antibacterial performance was observed when the board containing 7.5% UF and 7.5% GA was treated with two layers of 10% GA solution, which suppressed microbial growth to a remarkably low level of 4.30%. Conversely, high-concentration GA applications adversely affected performance and noticeably reduced antibacterial efficacy in samples containing only pure UF or GA.
- 1 January 2026
- Published by BioResources in BioResources
- Vol. 21 (3)
Effect of glutaraldehyde on the antibacterial resistance of waste office paper-based boards
This research investigated the effect of glutaraldehyde solutions on antibacterial resistance of composite boards manufactured with different combinations of urea formaldehyde (UF) and glutaraldehyde (GA) binder adhesives. The composite boards were general-purpose furniture panels (e.g., kitchen worktops, shelving, laboratory benchtops, or cabinet components) intended for household or workshop environments where surfaces may encounter microbial contamination from hands or spills, but not for direct food contact. Composite boards with varying UF/GA ratios and different binder solution concentrations were manufactured. The surfaces of these boards were treated with different numbers of layers (one or two) using GA solutions at 10% and 20% concentrations. The antibacterial performance of all samples was quantitatively evaluated by measuring the percentage of microbial growth. The results revealed a strong synergistic effect between the binder chemistry and surface treatment on antibacterial activity. The highest antibacterial performance was observed when the board containing 7.5% UF and 7.5% GA was treated with two layers of 10% GA solution, which suppressed microbial growth to a remarkably low level of 4.30%. Conversely, high-concentration GA applications adversely affected performance and noticeably reduced antibacterial efficacy in samples containing only pure UF or GA.
- 17 December 2025
- Published by Faculty of Forestry, Bursa Technical University in Ağaç ve Orman
- Vol. 6 (2) , 107-114
Kaynatma ve Presleme Süresinin Yoğunlaştırılmış Kavak (I-214 Populus × euramericana) Odununun Bazı Mekanik Özellikleri Üzerine Etkisi
Bu çalışmada, ülkemizde doğal yayılış gösteren kavak (I-214 Populus × euramericana) odununun, iki farklı kaynatma süresi (30 ve 60 dakika), iki farklı pres süresi (30 ve 60 dakika) ve iki farklı sıkıştırma oranı (%20 ve %40) ile termo-mekanik yoğunlaştırma işlemine tabi tutulması sonrasında mekanik özelliklerinde (eğilme direnci (MOR), elastikiyet modülü (MOE) ve Brinell sertlik) meydana gelen değişim incelenmiştir. Kaynatma ve pres sürelerinden bağımsız olarak %20 sıkıştırma sonrası MOE, MOR ve Brinell sertlik değerlerinde kontrol örneklerine kıyasla önemli bir fark olmadığı tespit edilirken, sıkıştırma oranı örnek kalınlığının %40’ına çıkarıldığında, mekanik özelliklerde kontrol örneklerine kıyasla önemli artışların meydana geldiği belirlenmiştir. Elde edilen sonuçlara göre 60 dakika kaynatma ön işlemi sonrasında 60 dakika preslenerek %40 oranında yoğunlaştırılan kavak odununun kontrol örneklerine kıyasla MOE değerinde %59 oranında artış olduğu belirlenmiştir. Ayrıca, yine aynı parametrelerde (60 dakika kaynatma, 60 dakika pres ve %40 sıkıştırma oranı) yoğunlaştırılan kavak odununda MOR ve Brinell sertlik değerlerinin de kontrol örneklerine kıyasla sırasıyla %54 ve %330 oranında artışın meydana geldiği tespit edilmiştir. Elde edilen bulgular, yoğunlaştırma işlemiyle birlikte artan yoğunluğun kavak odununun mekanik özelliklerini iyileştirdiğini göstermektedir. Bu durum, kavak odununun mobilya ve yapı endüstrilerinde yaygın olarak kullanılan diğer ağaç türlerine alternatif bir malzeme olarak kullanılabilme potansiyelini ortaya koymaktadır.
- 17 December 2025
- Published by Faculty of Forestry, Bursa Technical University in Ağaç ve Orman
- Vol. 6 (2) , 107-114
Kaynatma ve Presleme Süresinin Yoğunlaştırılmış Kavak (I-214 Populus × euramericana) Odununun Bazı Mekanik Özellikleri Üzerine Etkisi
Bu çalışmada, ülkemizde doğal yayılış gösteren kavak (I-214 Populus × euramericana) odununun, iki farklı kaynatma süresi (30 ve 60 dakika), iki farklı pres süresi (30 ve 60 dakika) ve iki farklı sıkıştırma oranı (%20 ve %40) ile termo-mekanik yoğunlaştırma işlemine tabi tutulması sonrasında mekanik özelliklerinde (eğilme direnci (MOR), elastikiyet modülü (MOE) ve Brinell sertlik) meydana gelen değişim incelenmiştir. Kaynatma ve pres sürelerinden bağımsız olarak %20 sıkıştırma sonrası MOE, MOR ve Brinell sertlik değerlerinde kontrol örneklerine kıyasla önemli bir fark olmadığı tespit edilirken, sıkıştırma oranı örnek kalınlığının %40’ına çıkarıldığında, mekanik özelliklerde kontrol örneklerine kıyasla önemli artışların meydana geldiği belirlenmiştir. Elde edilen sonuçlara göre 60 dakika kaynatma ön işlemi sonrasında 60 dakika preslenerek %40 oranında yoğunlaştırılan kavak odununun kontrol örneklerine kıyasla MOE değerinde %59 oranında artış olduğu belirlenmiştir. Ayrıca, yine aynı parametrelerde (60 dakika kaynatma, 60 dakika pres ve %40 sıkıştırma oranı) yoğunlaştırılan kavak odununda MOR ve Brinell sertlik değerlerinin de kontrol örneklerine kıyasla sırasıyla %54 ve %330 oranında artışın meydana geldiği tespit edilmiştir. Elde edilen bulgular, yoğunlaştırma işlemiyle birlikte artan yoğunluğun kavak odununun mekanik özelliklerini iyileştirdiğini göstermektedir. Bu durum, kavak odununun mobilya ve yapı endüstrilerinde yaygın olarak kullanılan diğer ağaç türlerine alternatif bir malzeme olarak kullanılabilme potansiyelini ortaya koymaktadır.
- 30 August 2025
- Published by Springer Nature in Mechanics of Composite Materials
- Vol. 61 (4) , 857-866
Effect of Nanoparticle Reinforcement on Mechanical Properties of Flexible Polyurethane Foams Used in Furniture
- 30 August 2025
- Published by Springer Nature in Mechanics of Composite Materials
- Vol. 61 (4) , 857-866
Effect of Nanoparticle Reinforcement on Mechanical Properties of Flexible Polyurethane Foams Used in Furniture
- 1 May 2024
- Published by BioResources in BioResources
- Vol. 19 (3) , 5935-5948
Shredded waste office paper as a component with wood particles in the production of particleboard
The effect of shredded waste office paper was considered when producing one-layered particleboard. Five different mixing ratios of shredded waste office paper/wood particles were used (0/100, 25/75, 50/50, 75/25, and 100/0) and two amounts of urea formaldehyde (UF) resin (10% and 15%). The boards were tested for their physical and mechanical properties, including modulus of elasticity (MOE), bending strength (MOR), and internal bond (IB) strength, in accordance with the European Norm (EN) standards. All properties of the boards were found to be improved via increasing the resin content. The 15% UF-bonded board with 100% wood particles had the highest MOR, whereas the board containing 100% wastepaper for 15% UF had the highest MOE. However, there was no statistical difference between the board types. Although increasing wastepaper content in the board negatively affected the IB, the usage of wastepaper up to 25% was shown to be acceptable as a raw material in the production of particleboard. None of the prepared boards met the EN 312 (1999) requirements for thickness swelling. The boards made from shredded waste office paper were more suitable for dry and indoor use.
- 1 May 2024
- Published by BioResources in BioResources
- Vol. 19 (3) , 5935-5948
Shredded waste office paper as a component with wood particles in the production of particleboard
The effect of shredded waste office paper was considered when producing one-layered particleboard. Five different mixing ratios of shredded waste office paper/wood particles were used (0/100, 25/75, 50/50, 75/25, and 100/0) and two amounts of urea formaldehyde (UF) resin (10% and 15%). The boards were tested for their physical and mechanical properties, including modulus of elasticity (MOE), bending strength (MOR), and internal bond (IB) strength, in accordance with the European Norm (EN) standards. All properties of the boards were found to be improved via increasing the resin content. The 15% UF-bonded board with 100% wood particles had the highest MOR, whereas the board containing 100% wastepaper for 15% UF had the highest MOE. However, there was no statistical difference between the board types. Although increasing wastepaper content in the board negatively affected the IB, the usage of wastepaper up to 25% was shown to be acceptable as a raw material in the production of particleboard. None of the prepared boards met the EN 312 (1999) requirements for thickness swelling. The boards made from shredded waste office paper were more suitable for dry and indoor use.
- 16 December 2022
- Published by Taylor & Francis in Wood Material Science & Engineering
- Vol. 18 (4) , 1478-1486
Study on tensile strength of single dovetail joint: experimental, numerical, and analytical analysis
The tensile strength of the single dovetail joint was investigated by experimental, numerical, and analytical methods. First, a numerical model of the dovetail joint was constructed based on the cohesive model using the Traction Separation law. Secondly, an analytical model was proposed based on the mechanical properties of the wood and the geometric dimensions of the dovetail joint. Finally, limited experimental tests (only changing the thickness length and width of the dovetail joint) were conducted to validate the numerical and analytical models. The results showed that the numerical model was an efficient method with ratios ranging from 0.84 to 1.35. The analytical model underestimated the tensile strength with ratios ranging from 0.63 to 0.85. The numerical analysis results showed that the dovetail tenon length and thickness significantly affect the maximum tensile strength. The tail angle and thickness significantly affected the elastic stiffness of the dovetail joint. The analytical model indicated the relationships between the dimensions of the dovetail joint and the tensile strength. The proposed methods will help to rationally design and optimize the tensile strength of a single dovetail joint.
- 16 December 2022
- Published by Taylor & Francis in Wood Material Science & Engineering
- Vol. 18 (4) , 1478-1486
Study on tensile strength of single dovetail joint: experimental, numerical, and analytical analysis
The tensile strength of the single dovetail joint was investigated by experimental, numerical, and analytical methods. First, a numerical model of the dovetail joint was constructed based on the cohesive model using the Traction Separation law. Secondly, an analytical model was proposed based on the mechanical properties of the wood and the geometric dimensions of the dovetail joint. Finally, limited experimental tests (only changing the thickness length and width of the dovetail joint) were conducted to validate the numerical and analytical models. The results showed that the numerical model was an efficient method with ratios ranging from 0.84 to 1.35. The analytical model underestimated the tensile strength with ratios ranging from 0.63 to 0.85. The numerical analysis results showed that the dovetail tenon length and thickness significantly affect the maximum tensile strength. The tail angle and thickness significantly affected the elastic stiffness of the dovetail joint. The analytical model indicated the relationships between the dimensions of the dovetail joint and the tensile strength. The proposed methods will help to rationally design and optimize the tensile strength of a single dovetail joint.
- Open Access
- 15 November 2022
- Published by University of Zagreb, Faculty of Forestry and Wood Technology in Drvna industrija
- Vol. 73 (4) , 445-452
Fracture Behavior of Wood Under Mode I Loading in Tangential Direction
The aim of this study was to determine the fracture behavior of southern yellow pine (Pinus taeda L.) and red oak (Quercus falcata) wood under mode I loading in the tangential-radial and tangential-longitudinal crack propagation systems by a compact tension test method. The results of the study indicated that, in general, red oak had a significantly different fracture behavior than southern yellow pine for each of the two crack propagation systems. The fracture toughness was higher in the tangential-radial crack propagation system than that in the tangential-longitudinal crack system, but there was no significant difference between the two crack propagation systems for southern yellow pine. The specific fracture energy of the tangential-longitudinal crack propagation system for both wood species was significantly lower than that of the tangential-radial crack propagation system. It means that more energy per unit area for the tangential-radial crack propagation system was needed to separate a wood sample into two halves. The difference in the fracture behavior of wood by the crack propagation system can be explained by the structural features of the tested samples since the crack propagation of the tangentialradial system crosses the annual ring and wood fibers can bridge the crack surface.
- 15 November 2022
- Published by University of Zagreb, Faculty of Forestry and Wood Technology in Drvna industrija
- Vol. 73 (4) , 445-452
Open AccessFracture Behavior of Wood Under Mode I Loading in Tangential Direction
The aim of this study was to determine the fracture behavior of southern yellow pine (Pinus taeda L.) and red oak (Quercus falcata) wood under mode I loading in the tangential-radial and tangential-longitudinal crack propagation systems by a compact tension test method. The results of the study indicated that, in general, red oak had a significantly different fracture behavior than southern yellow pine for each of the two crack propagation systems. The fracture toughness was higher in the tangential-radial crack propagation system than that in the tangential-longitudinal crack system, but there was no significant difference between the two crack propagation systems for southern yellow pine. The specific fracture energy of the tangential-longitudinal crack propagation system for both wood species was significantly lower than that of the tangential-radial crack propagation system. It means that more energy per unit area for the tangential-radial crack propagation system was needed to separate a wood sample into two halves. The difference in the fracture behavior of wood by the crack propagation system can be explained by the structural features of the tested samples since the crack propagation of the tangentialradial system crosses the annual ring and wood fibers can bridge the crack surface.
- 20 June 2022
- Published by Taylor & Francis in Wood Material Science & Engineering
- Vol. 18 (1) , 334-343
Study on withdrawal load resistance of screw in wood-based materials: experimental and numerical
The effects of screw diameter, pilot hole, and material type on withdrawal load resistance (WLR) of screw driven in medium density fibreboard (MDF) and particleboard (PB) were investigated through using experimental and numerical methods. Meanwhile, the results of experimental tests and numerical analysis were compared with the empirical equations. The results showed that (1) the material type and the diameter of screw had significant effects on the WLR, but the pilot hole was not; (2) the equations proposed in Eurocode 5 had better performance in predicting WLRs of screw in both MDF and PB than the other equations; (3) density distributions of wood-based materials affected the mechanical behaviours of WLR of screw; (4) finite element model (FE-model) established could be used to simulate the WLR of screw in wood-based samples; (5) the complex FE-model considering threads of screw can reflect the stress distributions on threads in detail, which contributes to optimal design of threads geometry of screws. And the simplified FE-model without considering threads of screw had advantages in predicting the WLR with higher accuracy.
- 20 June 2022
- Published by Taylor & Francis in Wood Material Science & Engineering
- Vol. 18 (1) , 334-343
Study on withdrawal load resistance of screw in wood-based materials: experimental and numerical
The effects of screw diameter, pilot hole, and material type on withdrawal load resistance (WLR) of screw driven in medium density fibreboard (MDF) and particleboard (PB) were investigated through using experimental and numerical methods. Meanwhile, the results of experimental tests and numerical analysis were compared with the empirical equations. The results showed that (1) the material type and the diameter of screw had significant effects on the WLR, but the pilot hole was not; (2) the equations proposed in Eurocode 5 had better performance in predicting WLRs of screw in both MDF and PB than the other equations; (3) density distributions of wood-based materials affected the mechanical behaviours of WLR of screw; (4) finite element model (FE-model) established could be used to simulate the WLR of screw in wood-based samples; (5) the complex FE-model considering threads of screw can reflect the stress distributions on threads in detail, which contributes to optimal design of threads geometry of screws. And the simplified FE-model without considering threads of screw had advantages in predicting the WLR with higher accuracy.
- 2 August 2021
- Published by Springer Nature in European Journal of Wood and Wood Products
- Vol. 79 (6) , 1495-1506
Effect of growth rings on fracture toughness of wood
- 2 August 2021
- Published by Springer Nature in European Journal of Wood and Wood Products
- Vol. 79 (6) , 1495-1506
Effect of growth rings on fracture toughness of wood