Marco Becker
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Marco Becker has a total of 23 co-authors. Here are the top co-authors by number of shared publications:
- Thomas Bergs
Manufacturing Technology Institute—MTI of RWTH Aachen University, Campus-Boulevard 30, 52074 Aachen, Germany
3 shared publications - Ali Rajaei
RWTH Aachen University
2 shared publications - Christoph Broeckmann
RWTH Aachen University
2 shared publications - Georg J. Schmitz
ACCESS e.V
2 shared publications - Gerhard Hirt
Institute of Metal Forming (IBF), RWTH Aachen University, Aachen, Germany
2 shared publications - Gerhard Lakemeyer
RWTH Aachen University
2 shared publications
Latest Publications
- Open Access
- 30 December 2023
- Published by Springer Nature
- p. 187-207
Materials in the Drive Chain – Modeling Materials for the Internet of Production
In this chapter, the focus lies on a predictive description of the material response to the thermomechanical loads within different process steps by means of physical and data-driven models. The modeling approaches are demonstrated in examples of innovative production technologies for components of a drive chain: Fine blanking of parts; powder metallurgical (PM) production of gears; open-die forging and machining of drive shafts. In fine blanking, material, process, and quality data are acquired to model interactions between process and material with data-driven methods. Interpretable machine learning is utilized to non-destructively characterize the initial material state, enabling an optimization of process parameters for a given material state in the long-term. The PM process chain of the gear includes sintering, pressing, surface densification, case hardening, and finishing by grinding. Several modeling and characterization approaches are applied to quantitatively describe the microstructure evolutions in terms of porosity during sintering, density profile after cold rolling, hardness and residual stresses after heat treating and grinding and the tooth root load bearing capacity. In the example of the open-die forging, a knowledge-based approach is developed to support the decision-making process regarding the choice of the proper material and optimized pass schedules. Considering the microstructure of the forged shaft, the elastoplastic material behavior is described by a dislocation-based, multiscale modeling approach. On this basis, process simulations could be carried out to predict the process forces, chip form, residual stresses, and the tool life among other output data.
- 30 December 2023
- Published by Springer Nature
- p. 187-207
Open AccessMaterials in the Drive Chain – Modeling Materials for the Internet of Production
In this chapter, the focus lies on a predictive description of the material response to the thermomechanical loads within different process steps by means of physical and data-driven models. The modeling approaches are demonstrated in examples of innovative production technologies for components of a drive chain: Fine blanking of parts; powder metallurgical (PM) production of gears; open-die forging and machining of drive shafts. In fine blanking, material, process, and quality data are acquired to model interactions between process and material with data-driven methods. Interpretable machine learning is utilized to non-destructively characterize the initial material state, enabling an optimization of process parameters for a given material state in the long-term. The PM process chain of the gear includes sintering, pressing, surface densification, case hardening, and finishing by grinding. Several modeling and characterization approaches are applied to quantitatively describe the microstructure evolutions in terms of porosity during sintering, density profile after cold rolling, hardness and residual stresses after heat treating and grinding and the tooth root load bearing capacity. In the example of the open-die forging, a knowledge-based approach is developed to support the decision-making process regarding the choice of the proper material and optimized pass schedules. Considering the microstructure of the forged shaft, the elastoplastic material behavior is described by a dislocation-based, multiscale modeling approach. On this basis, process simulations could be carried out to predict the process forces, chip form, residual stresses, and the tool life among other output data.
- Open Access
- 20 April 2023
- Published by Springer Nature
- p. 1-21
Materials in the Drive Chain – Modeling Materials for the Internet of Production
In this chapter, the focus lies on a predictive description of the material response to the thermomechanical loads within different process steps by means of physical and data-driven models. The modeling approaches are demonstrated in examples of innovative production technologies for components of a drive chain: Fine blanking of parts; powder metallurgical (PM) production of gears; open-die forging and machining of drive shafts. In fine blanking, material, process, and quality data are acquired to model interactions between process and material with data-driven methods. Interpretable machine learning is utilized to non-destructively characterize the initial material state, enabling an optimization of process parameters for a given material state in the long-term. The PM process chain of the gear includes sintering, pressing, surface densification, case hardening, and finishing by grinding. Several modeling and characterization approaches are applied to quantitatively describe the microstructure evolutions in terms of porosity during sintering, density profile after cold rolling, hardness and residual stresses after heat treating and grinding and the tooth root load bearing capacity. In the example of the open-die forging, a knowledge-based approach is developed to support the decision-making process regarding the choice of the proper material and optimized pass schedules. Considering the microstructure of the forged shaft, the elastoplastic material behavior is described by a dislocation-based, multiscale modeling approach. On this basis, process simulations could be carried out to predict the process forces, chip form, residual stresses, and the tool life among other output data.
- 20 April 2023
- Published by Springer Nature
- p. 1-21
Open AccessMaterials in the Drive Chain – Modeling Materials for the Internet of Production
In this chapter, the focus lies on a predictive description of the material response to the thermomechanical loads within different process steps by means of physical and data-driven models. The modeling approaches are demonstrated in examples of innovative production technologies for components of a drive chain: Fine blanking of parts; powder metallurgical (PM) production of gears; open-die forging and machining of drive shafts. In fine blanking, material, process, and quality data are acquired to model interactions between process and material with data-driven methods. Interpretable machine learning is utilized to non-destructively characterize the initial material state, enabling an optimization of process parameters for a given material state in the long-term. The PM process chain of the gear includes sintering, pressing, surface densification, case hardening, and finishing by grinding. Several modeling and characterization approaches are applied to quantitatively describe the microstructure evolutions in terms of porosity during sintering, density profile after cold rolling, hardness and residual stresses after heat treating and grinding and the tooth root load bearing capacity. In the example of the open-die forging, a knowledge-based approach is developed to support the decision-making process regarding the choice of the proper material and optimized pass schedules. Considering the microstructure of the forged shaft, the elastoplastic material behavior is described by a dislocation-based, multiscale modeling approach. On this basis, process simulations could be carried out to predict the process forces, chip form, residual stresses, and the tool life among other output data.
- 1 January 2023
- Published by Springer Nature
- p. 247-264
The Internet of Production as the Foundation of Data Utilization in Production
- 1 January 2023
- Published by Springer Nature
- p. 247-264
The Internet of Production as the Foundation of Data Utilization in Production
- 13 August 2021
- Published by Springer Nature
- p. 275-295
Das Internet of Production als Fundament der Datenverwertung in der Produktion
- 13 August 2021
- Published by Springer Nature
- p. 275-295
Das Internet of Production als Fundament der Datenverwertung in der Produktion