KCKaiyu Cai

Kaiyu Cai

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article

Previous Organizations / Institutes

The organizations / institutes from the scholar's other articles in the past ten years


Kaiyu Cai has a total of 15 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Open Access

    The Logical Framework of Human Behavior and Economics

    by Kaiyu Cai

    Human behavior is highly complex, and its underlying logic has long resisted systematic explanation. This paper advances four axioms as a general logical foundation for the analysis of human behavior and economics, from which ten corollaries are derived to form a unified theoretical framework. The framework provides a common basis for addressing major questions in economics and political economy, including the instability of extractive political institutions and the rise of sustained modern economic growth. More broadly, the paper highlights the possibility of explaining important phenomena in human behavior and economics through a small set of general principles rather than only through fragmented, case-specific accounts.

  • Open Access

    Modeling Options in Injection Molding Simulation

    by Kaiyu Cai, Jose Castro

    Injection molding is one of the most widely adopted manufacturing methods in the plastics industry, owing to its high efficiency, design flexibility, and mass production capabilities. Throughout the development and application of Injection molding technology, trade-offs are pervasive, arising from competing requirements such as processability versus material performance, productivity versus quality, and simplicity versus functionality. Injection molding simulation itself embodies such trade-offs, as it is used to design increasingly complex processes and mold systems to achieve improved material properties and part performance, while inevitably balancing physical accuracy against computational efficiency and modeling cost. This review examines typical modeling options in injection-molding simulation from an accuracy–complexity trade-off perspective. The modeling strategies adopted in the primary stages of the molding cycle—namely, the injection, packing, and cooling phases—are systematically reviewed, with emphasis on how simplifying assumptions are introduced to manage numerical complexity. By organizing existing research through the lens of qualitative trade-offs, this review aims to support a more structured understanding of model selection in injection molding simulation for both academic studies and industrial applications.

  • Effect of processing parameter changes on mechanical properties during injection molding: Amorphous versus semi‐crystalline materials

    by Kaiyu Cai, Travis O'LEary, Rachmat Mulyana, Jose M. Castro

    Injection molding is the most common method to mass‐produce plastic parts. The high cost and long lead time of traditional injection molding steel molds make 3D‐printed plastic molds a potential substitute for limited production runs and prototype parts. However, results suggest that for some materials, utilizing plastic molds (compared to metal molds) could decrease the mechanical properties of parts, especially the ductility. In order to better understand the issues with utilizing plastic molds, in this work, we use a design of experiments to investigate how the processing parameter changes affect mechanical properties by comparing a semi‐crystalline polypropylene and an amorphous polystyrene material in a metal mold for better control of the controllable variables. Results show that ductility is the most sensitive property to processing conditions, especially for polypropylene. Our analysis shows that the controllable variable that affects ductility the most is mold temperature, then packing pressure, and injection time.Highlights: 3D‐printed plastic molds is a potential substitute for limited production runs. Effects of processing parameters are analyzed through the design of experiments. Ductility is the most sensitive property to processing conditions for the material studied. Mold temperature is the most significant variable for ductility.


  • Open Access

    A model that discusses human behavior entirely

    by Kaiyu Cai, Lianhui Wang

    The complexity of human behavior results in a lack of understanding of its entirety, which inhibits recognition and progression. Here, we develop a model to describe all kinds of human behaviors and illustrate its excellent applicability in several important activities, i.e., progression, development and differentiation, freedom attainment, and sustainability maintenance.

  • Open Access

    Technical Feasibility of a Thermally Activated Nanotape for Electromagnetic Interference Applications

    by Kaiyu Cai, Dan Zhang, Jose M. Castro

    Multiwalled carbon nanotube (MWCNT) nanopaper (NP)-reinforced in-mold coating (IMC) nanocomposites were fabricated by dip soaking without organic solvent. The thermally activated IMC resin was selected to provide electromagnetic interference shielding protection for sheet molding compound (SMC) material as well as other plastic materials due to the proven good adhesion of IMC resin to the substrate. In this work, the technical feasibility of a continuous fabrication process was evaluated for a nanopaper/IMC (NP/IMC) composite. The curing behavior of the candidate IMC resin was studied for a better understanding of the fabrication of NP/IMC nanotape as a prepreg (with 10% polymerization), as well as the final curing once the nanotape was applied to the substrate. The required limiting maximum temperature to prevent curing during infiltration was established. This allows the fabrication of multilayer nanotape or coatings by stacking several layers of tape to improve the EMI shielding protection. To be specific, the average EMI shielding effectiveness for a one-layer composite was 21 dB, while it increased to 48 dB on average for a six-layer composite.

  • Difference in mechanical properties between plastic and metal molds for injection molding a talc reinforced rubber modified polypropylene

    by Dan Zhang, Leah Bartlett, Kaiyu Cai, Ben Hoffman, Rachmat Mulyana, Edward Herderick, Jose M. Castro

    Tooling for injection molding is costly, and delivery time is a concern, especially for companies that are on a tight production schedule. The introduction of additive manufacturing tooling for injection molding is an attractive rapid tooling for cutting cost and time not only for prototype parts but also for low volume production, that is, less than 100 parts. In this work, digital acrylonitrile butadiene styrene (ABS) mold insert was 3D printed on a Stratasys PolyJet printer, and then installed on the mold frame for injection molding investigation. The mechanical properties of talc reinforced rubber modified polypropylene (PP) parts molded by 3D printed ABS mold and conventional steel mold are compared. When the 3D printed ABS mold was used, a significantly higher mold temperature was observed during the molding cycles compared to the steel mold because of the lower thermal conductivity of ABS. The ductility of PP parts molded by the ABS mold is much lower compared to the metal mold, while other mechanical properties, such as tensile strength, Young's modulus, and flexural strength are not significantly different.


  • Improving processability for in‐mold coating formulations

    by Kaiyu Cai, Dan Zhang, Elliott J. Straus, Maria G. Villarreal, Jose M. Castro

    In‐mold coating (IMC) being 100% solids upon polymerization is an environmentally friendly alternative to traditional painting/coating. The standard commercial IMC formulation contains 2.8 wt% carbon black (CB) to achieve the electrical conductivity needed for maximum transfer efficiency during electrostatic painting. This formulation, however, makes the primed surface deep black and significantly increases the viscosity. To address this issue, our previous research evaluated the use of single‐wall carbon nanotubes as an alternative to CB. It was found that IMC with 0.15 wt% SWCNT provides the same level of conductivity as the standard IMC, but a much clear coating. However, the processability of this new formulation was adversely affected. In this research, other carbon‐based materials, that is, carbon nanofiber (CNF), multi‐wall carbon nanotube (MWCNT), and industrial graphene (grapheneblack [G]), were evaluated. Results indicate that the same level of conductivity can be reached by adding 1.6 wt% CNF, 1.8 wt% MWCNT, or 11.3 wt% G. Results also suggest that IMC with 1.8 wt% MWCNT has the best curing process, IMC with 11.3 wt% G has the highest flowability, and all three new formulations have a slightly better greyscale reading than the standard IMC.


  • Improving processability for in‐mold coating formulations: Part II: Two‐reinforcement formulations

    by Kaiyu Cai, Dan Zhang, Elliott J. Straus, Maria G. Villarreal, Jose M. Castro

    The in‐mold coating (IMC) process nowadays is well accepted by the sheet molding compound industry. The currently used IMC contains 2.8 wt% carbon black (CB) to provide enough electrical conductivity for maximum paint transfer efficiency (PTE) for electrostatic painting. Due to its relatively large viscosity, this formulation makes use of more than one injection gate for coating some large parts necessary. Our previous research investigated the possibility to replace the CB with higher conductivity carbon‐based nanoparticles, namely carbon nanofibers (CNFs), multi‐wall carbon nanotubes (MWCNTs), industrial graphene (grapheneblack [G]), and single‐wall carbon nanotubes (SWCNTs) and found that the IMC with 11.3 wt% G has the best processability among all IMC formulations. To improve this formulation, herein, we study the use of a second reinforcement in combination with G, i.e., CB, CNF, and MWCNT. Results from this study suggest that most G/CB‐reinforced IMC formulations have a better performance than the G‐reinforced IMC formulations, and IMC with 1 wt% CB and 6 wt% G is the best among all G/CB‐reinforced IMC formulations. To be specific, the new formulation allows parts to be painted to have a 300% increase in size when compared with the standard IMC.


  • A novel carbon nanotube nanopaper polyurethane coating for fiber reinforced composite substrates

    by Dan Zhang, Kaiyu Cai, Junjie Pan, L. James Lee, Jose M. Castro

    High performance carbon nanotube (CNT) nanopaper (NP) reinforced polyurethane (PU) nanocomposite coating with high potential for aerospace and automotive applications was successfully fabricated and evaluated in this work. Different PU formulations were used to fabricate nanocomposites to study the effect of hard segment content on resin infiltration and nanocomposite mechanical properties. The process window of PU infiltration into the CNT NP was established by rheology measurements and thermal gravimetric analysis (TGA). The micro‐structure morphology of the nanocomposite was characterized by scanning electron microscope (SEM). Uniform CNT distribution in PU matrix was observed in the high‐resolution SEM images, which indicated good resin impregnation quality. Based on mechanical properties and process window, a PU formulation was selected as matrix to fabricate NP/PU nanocomposite coating for carbon fiber/epoxy composites (CFPC) substrate. The flexural strength and impact resistance of the CFPC were significantly improved by 9% and 14.7% after applying the NP/PU nanocomposite coating. Aimed at industrial applications, a continuous nanopaper fabrication process was successfully demonstrated in this work. Through the process window study, a continuous process to fabricate nanocomposite is proposed for future scale‐up.