Zhengren Huang
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Zhengren Huang has a total of 36 co-authors. Here are the top co-authors by number of shared publications:
- Qing Huang
YongJiang Laboratory
5 shared publications - Quanxing Ren
Zhejiang Key Laboratory of Data-Driven High-Safety Energy Materials and Applications, Ningbo Key Laboratory of Special Energy Materials and Chemistry, Ningbo Institute of Materials Technology and Engineering, Chinese Academy of Sciences, Ningbo 315201, China
3 shared publications - Xishi Wu
State Key Laboratory of Advanced Marine Materials, Ningbo Institute of Materials Technology and Engineering, Chinese Academy of Sciences, Ningbo 315201, China
3 shared publications - Yinsheng Li
Zhejiang Key Laboratory of Data-Driven High-Safety Energy Materials and Applications, Ningbo Key Laboratory of Special Energy Materials and Chemistry, Ningbo Institute of Materials Technology and Engineering, Chinese Academy of Sciences, Ningbo 315201, China
3 shared publications - Haifeng Nie
Zhejiang Key Laboratory of Data-Driven High-Safety Energy Materials and Applications, Ningbo Key Laboratory of Special Energy Materials and Chemistry, Ningbo Institute of Materials Technology and Engineering, Chinese Academy of Sciences, Ningbo 315201, China
2 shared publications - Shuaixu Chun
College of Materials Science and Engineering, Zhejiang University of Technology, Hangzhou 310014, China
2 shared publications
Latest Publications
- Open Access
Hydrothermal Corrosion Resistance of Reaction-Bonded SiC Ceramic: Synergistic Enhancement by Homogeneous MoSi2 Distribution and Residual Silicon Reduction
Reaction-bonded SiC (RBSC) ceramics exhibit limited hydrothermal corrosion resistance due to the presence of residual silicon. This study presents a strategy to enhance the corrosion resistance of RBSC through homogeneous incorporation of MoSi2 and concurrent reduction in residual silicon content. Three material systems were fabricated via reactive melt infiltration: conventional RBSC with a SiC/C preform (SC), a SiC–MoSi2 composite incorporating commercial Mo2C powder via physical mixing (MC), and a SiC–MoSi2 composite derived from a Mo2C/C precursor synthesized by a molten salt method (MS). The Mo2C/C composite synthesized at 1150 °C exhibited fine, uniformly distributed Mo2C particles coated on carbon black, contrasting with the agglomerated distribution in commercial Mo2C mixtures. During reactive sintering at 1600 °C, Mo2C reacted with molten Si to form MoSi2, reducing residual Si content. Sample MS achieved the lowest residual Si (8.77 ± 0.45 vol.%), followed by MC (12.43 ± 0.86 vol.%) and SC (19.17 ± 1.01 vol.%). All samples achieved near-full densification (open porosity < 0.1%), with bulk densities of 2.96 ± 0.05, 3.03 ± 0.03, and 3.07 ± 0.03 g/cm3 for SC, MC, and MS, respectively. Microstructurally, MS displayed homogeneous MoSi2 dispersion, while MC showed partial MoSi2 aggregation, and SC contained continuous residual Si regions. Hydrothermal corrosion tests at 345 °C and 15 MPa for 9 days demonstrated that corrosion resistance followed the order MS > MC > SC. After 9 days, weight loss was 22.3970 ± 1.2059 mg/cm2 (SC), 17.6370 ± 0.8266 mg/cm2 (MC), and 15.4347 ± 0.7807 mg/cm2 (MS), with corrosion depths of 393.17 ± 27.46, 267.40 ± 24.44, and 224.60 ± 25.13 μm, respectively. The enhanced performance of MS arises from two synergistic factors: reduced residual Si minimizes large corrosion pores, while uniform distribution of MoSi2 facilitates the formation of a stable, dissolution-resistant composite oxide layer composed of MoO3 and SiO2, in which MoO3 restrains excessive dissolution of SiO2 through a pinning effect. These findings demonstrate that combining residual Si reduction with homogeneous MoSi2 incorporation via molten salt-synthesized precursors offers an effective strategy for improving hydrothermal corrosion resistance of reaction-bonded SiC-based materials for applications in high-temperature and high-pressure aqueous environments such as nuclear water reactors.
Open AccessHydrothermal Corrosion Resistance of Reaction-Bonded SiC Ceramic: Synergistic Enhancement by Homogeneous MoSi2 Distribution and Residual Silicon Reduction
Reaction-bonded SiC (RBSC) ceramics exhibit limited hydrothermal corrosion resistance due to the presence of residual silicon. This study presents a strategy to enhance the corrosion resistance of RBSC through homogeneous incorporation of MoSi2 and concurrent reduction in residual silicon content. Three material systems were fabricated via reactive melt infiltration: conventional RBSC with a SiC/C preform (SC), a SiC–MoSi2 composite incorporating commercial Mo2C powder via physical mixing (MC), and a SiC–MoSi2 composite derived from a Mo2C/C precursor synthesized by a molten salt method (MS). The Mo2C/C composite synthesized at 1150 °C exhibited fine, uniformly distributed Mo2C particles coated on carbon black, contrasting with the agglomerated distribution in commercial Mo2C mixtures. During reactive sintering at 1600 °C, Mo2C reacted with molten Si to form MoSi2, reducing residual Si content. Sample MS achieved the lowest residual Si (8.77 ± 0.45 vol.%), followed by MC (12.43 ± 0.86 vol.%) and SC (19.17 ± 1.01 vol.%). All samples achieved near-full densification (open porosity < 0.1%), with bulk densities of 2.96 ± 0.05, 3.03 ± 0.03, and 3.07 ± 0.03 g/cm3 for SC, MC, and MS, respectively. Microstructurally, MS displayed homogeneous MoSi2 dispersion, while MC showed partial MoSi2 aggregation, and SC contained continuous residual Si regions. Hydrothermal corrosion tests at 345 °C and 15 MPa for 9 days demonstrated that corrosion resistance followed the order MS > MC > SC. After 9 days, weight loss was 22.3970 ± 1.2059 mg/cm2 (SC), 17.6370 ± 0.8266 mg/cm2 (MC), and 15.4347 ± 0.7807 mg/cm2 (MS), with corrosion depths of 393.17 ± 27.46, 267.40 ± 24.44, and 224.60 ± 25.13 μm, respectively. The enhanced performance of MS arises from two synergistic factors: reduced residual Si minimizes large corrosion pores, while uniform distribution of MoSi2 facilitates the formation of a stable, dissolution-resistant composite oxide layer composed of MoO3 and SiO2, in which MoO3 restrains excessive dissolution of SiO2 through a pinning effect. These findings demonstrate that combining residual Si reduction with homogeneous MoSi2 incorporation via molten salt-synthesized precursors offers an effective strategy for improving hydrothermal corrosion resistance of reaction-bonded SiC-based materials for applications in high-temperature and high-pressure aqueous environments such as nuclear water reactors.
- Open Access
Tribological Behavior and Self-Lubrication Mechanisms of Cf/SiC-B12(C,Si,B)3 Composites Under Coupled Temperature-Velocity Conditions: A Preliminary Study
To address the increasing demands for lightweight, high-temperature resistant braking materials under extreme service conditions, a novel Cf/SiC-B12(C,Si,B)3 composite was developed in this work. The composite was fabricated via a hybrid slurry infiltration-reactive melt infiltration (SI-RMI) process. The tribological performance under coupled temperature–velocity conditions was systematically evaluated using a ball-on-disk tester over temperatures from 25 to 600 °C (at 900 r/min) and sliding speeds from 300 to 900 r/min (at 600 °C). The results indicate that temperature dominates the friction and wear behavior. At room temperature, the composite exhibits a friction coefficient of 0.52 and a wear rate of 4.019 × 10−4 mm3/(N·m). With increasing temperature, friction coefficients decreased to 0.43 at 400 °C and 0.41 at 600 °C, while wear rates increased sharply to 12.025 × 10−4 mm3/(N·m) at 400 °C before declining to 5.228 × 10−4 mm3/(N·m) at 600 °C. Under the fixed temperature of 600 °C, raising rotational speed from 300 to 900 r/min increased the wear rate only marginally (4.953 to 5.228 × 10−4 mm3/(N·m)). Surface analysis indicates that a continuous Si-B-O oxide layer (mainly SiO2 and B2O3) forms at 600 °C, which may provide solid lubrication and oxidation resistance. The present work offers a preliminary exploration of the tribological evolution and self-lubrication mechanisms of Cf/SiC-B12(C,Si,B)3 composites, providing potential insights for the design of advanced ceramic-matrix braking materials.
Open AccessTribological Behavior and Self-Lubrication Mechanisms of Cf/SiC-B12(C,Si,B)3 Composites Under Coupled Temperature-Velocity Conditions: A Preliminary Study
To address the increasing demands for lightweight, high-temperature resistant braking materials under extreme service conditions, a novel Cf/SiC-B12(C,Si,B)3 composite was developed in this work. The composite was fabricated via a hybrid slurry infiltration-reactive melt infiltration (SI-RMI) process. The tribological performance under coupled temperature–velocity conditions was systematically evaluated using a ball-on-disk tester over temperatures from 25 to 600 °C (at 900 r/min) and sliding speeds from 300 to 900 r/min (at 600 °C). The results indicate that temperature dominates the friction and wear behavior. At room temperature, the composite exhibits a friction coefficient of 0.52 and a wear rate of 4.019 × 10−4 mm3/(N·m). With increasing temperature, friction coefficients decreased to 0.43 at 400 °C and 0.41 at 600 °C, while wear rates increased sharply to 12.025 × 10−4 mm3/(N·m) at 400 °C before declining to 5.228 × 10−4 mm3/(N·m) at 600 °C. Under the fixed temperature of 600 °C, raising rotational speed from 300 to 900 r/min increased the wear rate only marginally (4.953 to 5.228 × 10−4 mm3/(N·m)). Surface analysis indicates that a continuous Si-B-O oxide layer (mainly SiO2 and B2O3) forms at 600 °C, which may provide solid lubrication and oxidation resistance. The present work offers a preliminary exploration of the tribological evolution and self-lubrication mechanisms of Cf/SiC-B12(C,Si,B)3 composites, providing potential insights for the design of advanced ceramic-matrix braking materials.
- Open Access
The Modulation of the Pore Structure in Porous Carbon by Metal Salts and Its Application for Joining Silicon Carbide Ceramics
In this work, the metal salts were introduced into the resin-solvent gel system to leverage their ortho-substitution effect, thereby accelerating the polymerization-induced phase separation process. Subsequent in-situ carbonization resulted in the preparation of porous carbon materials with three-dimensional interconnected pores. By precisely tuning the parameters of the resin-solvent-metal ion system, control over the pore structure of the porous carbon was achieved, with a porosity range of 16.5% to 66.5% and a pore diameter range of 8 to 248 nm. The addition of metallic salts can simply and effectively increase the pore structure after carbonization, making the infiltration of molten silicon easier. This is beneficial to the joining process of silicon carbide ceramics. Based on these findings, a high-reliability joining technique for large-sized (135 mm × 205 mm) silicon carbide ceramics was developed. The resulting interlayer was dense and defect-free, exhibiting a joining strength of 309 ± 33 MPa and a Weibull modulus of 10.67. These results highlight the critical role of structured porous media in advancing the field of large-sized ceramic joining.
Open AccessThe Modulation of the Pore Structure in Porous Carbon by Metal Salts and Its Application for Joining Silicon Carbide Ceramics
In this work, the metal salts were introduced into the resin-solvent gel system to leverage their ortho-substitution effect, thereby accelerating the polymerization-induced phase separation process. Subsequent in-situ carbonization resulted in the preparation of porous carbon materials with three-dimensional interconnected pores. By precisely tuning the parameters of the resin-solvent-metal ion system, control over the pore structure of the porous carbon was achieved, with a porosity range of 16.5% to 66.5% and a pore diameter range of 8 to 248 nm. The addition of metallic salts can simply and effectively increase the pore structure after carbonization, making the infiltration of molten silicon easier. This is beneficial to the joining process of silicon carbide ceramics. Based on these findings, a high-reliability joining technique for large-sized (135 mm × 205 mm) silicon carbide ceramics was developed. The resulting interlayer was dense and defect-free, exhibiting a joining strength of 309 ± 33 MPa and a Weibull modulus of 10.67. These results highlight the critical role of structured porous media in advancing the field of large-sized ceramic joining.
- 8 February 2025
- Published by Springer Nature in Silicon
- Vol. 17 (4) , 851-860
Catalytic Conversion of Residual Carbon in Precursor-Derived SiC into Carbon Nanotubes Using Metal Nickel and Mechanism Analysis
- 8 February 2025
- Published by Springer Nature in Silicon
- Vol. 17 (4) , 851-860
Catalytic Conversion of Residual Carbon in Precursor-Derived SiC into Carbon Nanotubes Using Metal Nickel and Mechanism Analysis
- Open Access
Effects of Preformed Composition and Pore Size on Microstructure and Properties of SiCf/SiC Composites via Reactive Melt Infiltration
This study investigated the influence of preformed composition and pore size on the microstructure and properties of SiCf/SiC composites fabricated via reactive melt infiltration (RMI). The process began with the impregnation of SiC fiber cloth with phenolic resin, followed by lamination and pyrolysis. Subsequent steps included further impregnations with phenolic resin, SiC slurry, and carbon black slurry, each followed by additional pyrolysis. This process resulted in three types of preforms, designated as PP, PS, and PC. These preforms exhibited a multimodal distribution of pore size, with peak pore diameters around 5 μm for PP, ranging from 200 nm to 4 μm for PS, and approximately 150 nm for PC. The preforms were then subjected to molten silicon infiltration at 1600 °C under vacuum for 1 h to create SiCf/SiC composites. The PP preform contained only pyrolytic carbon, leading to a composite with high closed porosity and unreacted carbon, resulting in poor mechanical properties. The PS preform, which was impregnated with SiC particles, displayed an optimized pore size distribution but retained significant amounts of residual silicon and carbon in the final composite. In contrast, the PC preform featured both an ideal pore size distribution and an adequate amount of carbon, achieving high density and low porosity with reduced residual phases in the final composite. This optimization led to a flexural strength of 152.4 ± 15.4 MPa, an elastic modulus of about 181.1 ± 0.1 GPa, and a thermal conductivity of 27.7 W/mK in the SiCf/SiC composites product. These findings underscore the importance of preform optimization in enhancing the performance of SiCf/SiC composites, potentially paving the way for more reliable nuclear fuel cladding solutions.
Open AccessEffects of Preformed Composition and Pore Size on Microstructure and Properties of SiCf/SiC Composites via Reactive Melt Infiltration
This study investigated the influence of preformed composition and pore size on the microstructure and properties of SiCf/SiC composites fabricated via reactive melt infiltration (RMI). The process began with the impregnation of SiC fiber cloth with phenolic resin, followed by lamination and pyrolysis. Subsequent steps included further impregnations with phenolic resin, SiC slurry, and carbon black slurry, each followed by additional pyrolysis. This process resulted in three types of preforms, designated as PP, PS, and PC. These preforms exhibited a multimodal distribution of pore size, with peak pore diameters around 5 μm for PP, ranging from 200 nm to 4 μm for PS, and approximately 150 nm for PC. The preforms were then subjected to molten silicon infiltration at 1600 °C under vacuum for 1 h to create SiCf/SiC composites. The PP preform contained only pyrolytic carbon, leading to a composite with high closed porosity and unreacted carbon, resulting in poor mechanical properties. The PS preform, which was impregnated with SiC particles, displayed an optimized pore size distribution but retained significant amounts of residual silicon and carbon in the final composite. In contrast, the PC preform featured both an ideal pore size distribution and an adequate amount of carbon, achieving high density and low porosity with reduced residual phases in the final composite. This optimization led to a flexural strength of 152.4 ± 15.4 MPa, an elastic modulus of about 181.1 ± 0.1 GPa, and a thermal conductivity of 27.7 W/mK in the SiCf/SiC composites product. These findings underscore the importance of preform optimization in enhancing the performance of SiCf/SiC composites, potentially paving the way for more reliable nuclear fuel cladding solutions.
- 26 June 2024
- Published by Royal Society of Chemistry (RSC) in Journal of Materials Chemistry C
- Vol. 12 (31) , 11898-11906
Laminated composite of ceramic/glass films to realize high luminous efficiency and high color quality in laser-driven white lighting
As for high-power laser diode (LD) driven lighting, Y3Al5O12:Ce3+ phosphor ceramics (YAG:Ce-CPs) are regarded as ideal converters to produce white light. Due to the lack of the red component, it is still one of the biggest challenges to obtain high-quality light for YAG:Ce-CPs in LD lighting. In this work, CaAlSiN3:Eu2+ phosphor-in-glass-films (CASN:Eu-PiGFs) are introduced to offset the emitting spectrum of YAG:Ce and suitable glass powders are employed as the inorganic binder to fabricate CASN:Eu-PiGFs. After coating CASN:Eu-PiGFs, a broad emitting spectrum (from 500 to 750 nm) is achieved. The luminous performances and thermal stability are optimized by modifying the CASN:Eu content in PiGF. In LD lighting, high luminous flux (858 lm) and luminous efficiency (165 lm W−1) can be obtained. Meanwhile, owing to the remedy of the emitting spectrum, a high color render index (CRI, 82) is acquired for YAG:Ce-CPs in LD lighting. The strategy makes big progress in designing phosphor converters and will inspire more researchers to pursue high-quality white light in LD-driven lighting.
- 26 June 2024
- Published by Royal Society of Chemistry (RSC) in Journal of Materials Chemistry C
- Vol. 12 (31) , 11898-11906
Laminated composite of ceramic/glass films to realize high luminous efficiency and high color quality in laser-driven white lighting
As for high-power laser diode (LD) driven lighting, Y3Al5O12:Ce3+ phosphor ceramics (YAG:Ce-CPs) are regarded as ideal converters to produce white light. Due to the lack of the red component, it is still one of the biggest challenges to obtain high-quality light for YAG:Ce-CPs in LD lighting. In this work, CaAlSiN3:Eu2+ phosphor-in-glass-films (CASN:Eu-PiGFs) are introduced to offset the emitting spectrum of YAG:Ce and suitable glass powders are employed as the inorganic binder to fabricate CASN:Eu-PiGFs. After coating CASN:Eu-PiGFs, a broad emitting spectrum (from 500 to 750 nm) is achieved. The luminous performances and thermal stability are optimized by modifying the CASN:Eu content in PiGF. In LD lighting, high luminous flux (858 lm) and luminous efficiency (165 lm W−1) can be obtained. Meanwhile, owing to the remedy of the emitting spectrum, a high color render index (CRI, 82) is acquired for YAG:Ce-CPs in LD lighting. The strategy makes big progress in designing phosphor converters and will inspire more researchers to pursue high-quality white light in LD-driven lighting.
- Open Access
Joining of SiC Ceramic by Si–C Reaction Bonding Using Organic Resin as Carbon Precursor
In this study, the joining of silicon carbide (SiC) ceramics was achieved via a Si–C reaction bonding method using the phenolic resin (PF)–MgCl2 system as the carbon precursor. Specifically, by adding MgCl2 to the phenolic resin mixture, the average pore size of the product of carbonization of the PF resin mixture increased from 14 ± 5 nm to 524 ± 21 nm, which was beneficial for the infiltration of molten silicon at high temperature. The microstructure of the joined specimens and the effect of the inert filler on the joint strength were investigated. It was demonstrated that SiC–SiC joints with strong interfacial bonding and high flexural strength could be obtained by the Si–C reaction bonding method using a phenol formaldehyde resin/alcohol sol-gel system as the carbon precursor. The flexural strength of the joined specimens reached the highest value, i.e., 308 ± 27 MPa when the solid loading of the inert filler was 26%. Overall, stable joining of silicon carbide ceramics was achieved by the proposed method, which has significance for realizing the preparation of complex-shaped or large silicon carbide ceramic parts.
Open AccessJoining of SiC Ceramic by Si–C Reaction Bonding Using Organic Resin as Carbon Precursor
In this study, the joining of silicon carbide (SiC) ceramics was achieved via a Si–C reaction bonding method using the phenolic resin (PF)–MgCl2 system as the carbon precursor. Specifically, by adding MgCl2 to the phenolic resin mixture, the average pore size of the product of carbonization of the PF resin mixture increased from 14 ± 5 nm to 524 ± 21 nm, which was beneficial for the infiltration of molten silicon at high temperature. The microstructure of the joined specimens and the effect of the inert filler on the joint strength were investigated. It was demonstrated that SiC–SiC joints with strong interfacial bonding and high flexural strength could be obtained by the Si–C reaction bonding method using a phenol formaldehyde resin/alcohol sol-gel system as the carbon precursor. The flexural strength of the joined specimens reached the highest value, i.e., 308 ± 27 MPa when the solid loading of the inert filler was 26%. Overall, stable joining of silicon carbide ceramics was achieved by the proposed method, which has significance for realizing the preparation of complex-shaped or large silicon carbide ceramic parts.
- 1 January 2022
- Published by Shanghai Institute of Ceramics in Journal of Inorganic Materials
- Vol. 37 (12) , 1275-1280
Effect of Pore Structure of Organic Resin-based Porous Carbon on Joining Properties of Cf/SiC Composites
- 1 January 2022
- Published by Shanghai Institute of Ceramics in Journal of Inorganic Materials
- Vol. 37 (12) , 1275-1280
Effect of Pore Structure of Organic Resin-based Porous Carbon on Joining Properties of Cf/SiC Composites
- Open Access
- 20 August 2021
- Published by Wiley in Nano Select
- Vol. 3 (4) , 834-840
Facile synthesis of a novel transparent melt‐spinnable polysilazane
- 20 August 2021
- Published by Wiley in Nano Select
- Vol. 3 (4) , 834-840
Open AccessFacile synthesis of a novel transparent melt‐spinnable polysilazane