Marc Lany
Marc Lany has a total of 10 co-authors. Here are the top co-authors by number of shared publications:
- Adriaan Bernardus Spierings
Inspire AG
2 shared publications - Marvin Aaron Spurek
Institute for Diagnostic and Interventional Radiology, Faculty of Medicine, University Hospital Cologne, University of Cologne, 50937 Cologne, Germany
2 shared publications Bernard Revaz
1 shared publication- Bernard Revaz
Sensima Inspection SARL, 2 Route Cité Ouest, 1196 Gland, Switzerland
1 shared publication Gilles Santi
1 shared publication- Gilles Santi
Sensima Inspection SARL, 2 Route Cité Ouest, 1196 Gland, Switzerland
1 shared publication
Latest Publications
- Open Access
- 4 November 2022
- Published by Elsevier in Additive Manufacturing
- Vol. 60
In-situ monitoring of powder bed fusion of metals using eddy current testing
- 4 November 2022
- Published by Elsevier in Additive Manufacturing
- Vol. 60
Open AccessIn-situ monitoring of powder bed fusion of metals using eddy current testing
- Open Access
Relative Density Measurement of PBF-Manufactured 316L and AlSi10Mg Samples via Eddy Current Testing
Powder bed fusion (PBF) is the most commonly used additive manufacturing process for fabricating complex metal parts via the layer-wise melting of powder. Despite the tremendous recent technological development of PBF, manufactured parts still lack consistent quality in terms of part properties such as dimensional accuracy, surface roughness, or relative density. In addition to process-inherent variability, this is mainly owing to a knowledge gap in the understanding of process influences and the inability to adequately control them during part production. Eddy current testing (ECT) is a well-established nondestructive testing technique primarily used to detect near-surface defects and measure material properties such as electrical conductivity in metal parts. Hence, it is an appropriate technology for the layer-wise measuring of the material properties of the fused material in PBF. This study evaluates ECT’s potential as a novel in situ monitoring technology for relative part density in PBF. Parts made from SS316L and AlSi10Mg with different densities are manufactured on a PBF machine. These parts are subsequently measured using ECT, as well as the resulting signals correlated with the relative part density. The results indicate a statistically significant and strong correlation (316L: r(8) = 0.998, p < 0.001, AlSi10Mg: r(8) = 0.992, p < 0.001) between relative part density and the ECT signal component, which is mainly affected by the electrical conductivity of the part. The results indicate that ECT has the potential to evolve into an effective technology for the layer-wise measuring of relative part density during the PBF process.
Open AccessRelative Density Measurement of PBF-Manufactured 316L and AlSi10Mg Samples via Eddy Current Testing
Powder bed fusion (PBF) is the most commonly used additive manufacturing process for fabricating complex metal parts via the layer-wise melting of powder. Despite the tremendous recent technological development of PBF, manufactured parts still lack consistent quality in terms of part properties such as dimensional accuracy, surface roughness, or relative density. In addition to process-inherent variability, this is mainly owing to a knowledge gap in the understanding of process influences and the inability to adequately control them during part production. Eddy current testing (ECT) is a well-established nondestructive testing technique primarily used to detect near-surface defects and measure material properties such as electrical conductivity in metal parts. Hence, it is an appropriate technology for the layer-wise measuring of the material properties of the fused material in PBF. This study evaluates ECT’s potential as a novel in situ monitoring technology for relative part density in PBF. Parts made from SS316L and AlSi10Mg with different densities are manufactured on a PBF machine. These parts are subsequently measured using ECT, as well as the resulting signals correlated with the relative part density. The results indicate a statistically significant and strong correlation (316L: r(8) = 0.998, p < 0.001, AlSi10Mg: r(8) = 0.992, p < 0.001) between relative part density and the ECT signal component, which is mainly affected by the electrical conductivity of the part. The results indicate that ECT has the potential to evolve into an effective technology for the layer-wise measuring of relative part density during the PBF process.